Sea gull lighting | 44851-782 | Installation guide | Sea Gull Lighting 44851-782 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don't need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
UNIVERSAL
MOUNTING
BAR (D)
012108
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
HC-1287
GREEN
GROUND
GROUNDING WIRE
SCREW (G)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
CANOPY (I)
CAP NUT (E)
SOCKET
CUP (B)
NIPPLE (F)
NUT (J)
SHADE (A)
RETAINING RING (H)
FIGURE 1
*NOT INCLUDED
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
GREEN
GROUNDING
SCREW (G)
*OUTLET BOX
SCREWS
NIPPLE (F)
GROUND
WIRE
NUT (J)
*WIRE CONNECTOR
UNIVERSAL
MOUNTING BAR (D)
FIGURE 2
*NOT SUPPLIED
INSTALLATION
HC-1287
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert nipple (F) into universal mounting bar (D) so five threads are
exposed past universal mounting bar (D). Secure by threading nut
(J) onto universal mounting bar (D).
STEP 2:
Using outlet box screws (not supplied) fasten universal mounting bar
(D) to outlet box through slots in universal mounting bar (D).
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (D). Wrap the ground wire from the fixture (if supplied) and
the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (G) on the
universal mounting bar (D) if uninsulated wire is on the universal
mounting bar (D), connect the ground wire from the fixture (if
supplied) and the outlet box to it using a small wire connector (not
supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors. After
wires are connected, tuck them carefully inside outlet box. Push the
fixture firmly over the nipple (F) and against the wall. Secure canopy
(I) in place by threading cap nut (E) onto nipple (F).
Place shade (A) on socket cup (B) and secure by threading retaining
ring (H) onto socket.
STEP 2:
Install lamps.
STEP 3:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF