Sea gull lighting | 49850BLE-782 | Installation guide | Sea Gull Lighting 49850BLE-782 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
BEFORE YOU BEGIN
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Save these instructions.
*OUTLET BOX
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
UNIVERSAL
MOUNTING
BAR (D)
CAP
NUT
(H)
GLASS (J)
CANOPY (I)
MOUNTING
SCREWS (F)
GLASS RETAINING
RING (M)
FIGURE 1
*NOT INCLUDED
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
GREEN
GROUNDING
SCREW (G)
*OUTLET BOX
SCREWS
MOUNTING
SCREWS (F)
GROUND
WIRE
*WIRE CONNECTOR
UNIVERSAL
MOUNTING BAR (D)
FIGURE 2
Installation And Safety
Instruction
HC-1375 052708
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_________
HC-1375
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Run fixture mounting screws (F) through holes in universal mounting
bar (D) all the way down to their heads. Using outlet box screws (not
supplied) fasten universal mounting bar (D) to outlet box through
slots in universal mounting bar (D). Be sure fixture mounting screws
(F) are perfectly horizontal so fixture hangs straight.
STEP 2:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 3:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is
to be inserted into the hole with two raised dimples provided on the
universal mounting bar (D). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (G) on the
universal mounting bar (D). Tighten the green grounding screw (G)
to secure. If uninsulated wire is on the universal mounting bar (D),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors.
STEP 2:
After wires are connected, tuck them carefully inside outlet box. Push
the fixture firmly over the mounting screws (F) and against the wall.
Secure canopy (I) in place by threading cap nuts (H) to nipple (F).
STEP 3:
Place glass (J) over socket (B) and secure in place or by threading
retaining ring (M) to socket (B).
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 4:
Install lamp (A) by twisting into socket (B).
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
ONE PIECE
LAMP/BALLAST
COMBINATION
ONE PIECE LAMP/
BALLAST
COMBINATION (A)
Hg
MARK MEANS LAMP CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
SOCKET (B)
FIGURE 2
Download PDF