Sea gull lighting | 51521-845 | Installation guide | Sea Gull Lighting 51521-845 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
BEFORE YOU BEGIN
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
To reduce the risk of fire, electric shock, or personal injury, mount to
outlet box or supporting system able to support the weight of the
fixture.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house electrical
wires, nor should a swag type fixture be installed on a ceiling which
contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
*GROUND WIRE
NUT (B)
NIPPLE (C)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
STEP 1:
Rotate arms (N) (if applicable).
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
*WIRE CONNECTORS
MOUNTING BAR (A)
*OUTLET BOX SCREWS
*WIRE
CONNECTORS
SCREW COLLAR (E)
CANOPY (H)
SCREW COLLAR
RING (G)
CHAIN (S)
MOUNTING
BAR (A)
*OUTLET BOX
SCREWS
FIXTURE LOOP (K)
GREEN
GROUNDING
SCREW (D)
FIGURE 2
NUT (B)
NIPPLE (C)
*NOT SUPPLIED
ARMS (N)
BOBECHE (M)
BOBECHE (O)
Installation And
Safety Instruction
HC-1151
081307
FIGURE 1
FINIAL (Z)
*NOT SUPPLIED
Fill In Item Number On Carton And
File This Sheet For Fixture Reference.
ITEM#_______________
INSTALLATION
HC-1151
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
1. Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that five threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A)
and secure by tightening nut (B) to mounting bar (A). Thread screw
collar (E) to nipple (C).
2. Using two pairs of pliers, open one link of chain (S) and connect it
to the fixture loop (K) at the top of the fixture. Pass the wire
through screw collar ring (G) and canopy (H). Slide screw collar
ring (G) and canopy (H) to fixture loop (K).
3. Open one link on the other end of the chain (S) and attach it to
screw collar (E). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
4. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the following directions:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND &
SMOOTH)
*PARALLEL WIRE (SQUARE &
RIDGED)
*Note: When parallel wire is used, the tracer wire is square
shaped or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
5. GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on
the mounting bar (A). Wrap the ground wire (F) from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated wire is on the mounting bar (A),
connect the ground wire (F) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
1. After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (H) against the ceiling and thread the screw
collar ring (G) to the screw collar (E).
2. Place glass (M) into bobeche (O).
3. Install lamps.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when ordering
parts.
Download PDF