Quick Start Guide: Cisco Aironet 1250 Series Access Point

Add to my manuals
36 Pages

advertisement

Quick Start Guide: Cisco Aironet 1250 Series Access Point | Manualzz

Read This First

This guide is designed to help you prepare your Cisco Aironet 1250 Series

Access Point (hereafter referred to as the access point) for use on your wireless network. This section contains important information on what you you need to know so that you can successfully prepare and deploy your access point.

Login and Password

The default login and password used to access the access point GUI or CLI is

Cisco. The password and login is case sensitive.

Removing the Mounting Plate

The access point ships with the mounting plate attached. You must remove the plate before you can connect the power and Ethernet cables and access the console port.

After unpacking the access point, follow these steps to remove the mounting plate.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

1

Step 1

Grasp the access point with both hands as shown in the illustration below.

2

78-17831-01

Step 2

With your right thumb or forefinger, pull the security hasp toward you to release it from the mounting plate.

Step 3

Maintain pressure on the security hasp, use your thumb or forefinger to push the mounting plate to the right, and slide it off the mounting plate pins.

Step 4

Remove the mounting plate from the access point.

Radio and IP Address Configuration

The access point ships with its radios disabled and no assigned IP address or service set identifier (SSID). You must enable the radios when you configure the access point for the first time. Also, the access point no longer is assigned a default IP address. It is configured to obtain an IP address using a DHCP server. If your network does not use a DHCP server, you must connect to the access point’s console port and assign a static IP address. See the

“Obtaining and Assigning an IP Address” section on page 18 .

Bridging Feature Not Tested

The 1250 series access point has not been tested for bridging purposes, even though the commands for configuring the unit as a bridge are available.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

3

Before You Start

Because the configuration process varies depending on how you intend to use your access point, detailed configuration instructions are not discussed in this guide.

Configuration instructions specific to your intended use are covered in the

“Configuring the Access Point for the First Time” chapter of the Cisco IOS

Software Configuration Guide for Cisco Aironet Access Points.

We also recommend that you have the following documents available:

Cisco IOS Software Configuration Guide for Cisco Aironet Access

Points—provides detailed information for advanced configurations.

Cisco Aironet Command Reference for Cisco Aironet Access Points and

Bridges—lists all Cisco IOS commands with descriptions and syntax instructions.

Cisco Aironet 1250 Series Access Point Hardware Installation

Guide—provides mounting instructions, compliance information, and technical specifications.

Release Notes for Cisco Aironet Access Points for Cisco IOS Release

12.4(3g)JA (or later)—provides system requirements, new feature descriptions, important notes, limitations, and last-minute updates.

4

78-17831-01

These documents are also available on cisco.com. Follow this link: http://www.cisco.com/en/US/products/ps6973/tsd_products_support_series_ home.html

Make sure that you are using a computer connected to the same network as the access point, and obtain the following information from your network administrator:

A host name for the access point.

The case-sensitive SSID for your 802.11 radio network.

A Simple Network Management Protocol (SNMP) community name and the SNMP file attribute (if SNMP is in use).

The Media Access Control (MAC) address from the label on the bottom of the access point (such as 0016462584c), if you plan to use the Cisco

IP Setup Utility to find an access point IP address.

If you are not connected to a DHCP server, you can assign an IP address to the access point using the CLI. In this situation, obtain a unique IP address for your access point, a default gateway, and subnet mask from your network system administrator.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

5

Safety Information

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by

FCC certified equipment. When used with approved Cisco Aironet antennas,

Cisco Aironet products meet the uncontrolled environmental limits found in

OET-65 and ANSI C95.1, 1991.

Proper installation of this radio according to the instructions found in this manual will result in user exposure that is substantially below the FCC recommended limits.

Do not hold any component containing a radio so that the antenna is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.

The use of wireless devices in hazardous locations is limited to the constraints posed by the safety directors of such environments.

Warnings

Translated versions of the following safety warnings are provided in the

Safety Warnings for Cisco Aironet 1250 Series Access Points document that ships with the access point.

6

78-17831-01

Warning

Read the installation instructions before you connect the

system to its power source. Statement 1004

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than:

20A Statement 1005

Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such

use. Statement 245B

Warning

In order to comply with FCC radio frequency (RF) exposure limits, antennas should be located at a minimum of 7.9 inches

(20 cm) or more from the body of all persons. Statement 332

Quick Start Guide: Cisco Aironet 1250 Series Access Point

7

Unpacking the Access Point

Package Contents

Each access point package contains the following items:

Cisco Aironet 1250 series autonomous access point

Mounting hardware kit

– One mounting plate, two 4 x 40 x 3/16 in screws, and a mounting plate latch (all attached to the access point)

– Two suspended ceiling T-rail clips, spacers (accommodates standard and recessed T-rails), and nuts

– Four 8 x 18 x 3/4 in pan head Phillips sheet metal screws

– Four #8 plastic wall anchors

– One 10 x 24 nut (for ground stud on the mounting plate)

– Two cable tie wraps

Product quick start guide

Product translated safety warning document

Cisco product registration card

Follow these steps to unpack the access point:

8

78-17831-01

Step 1

Open the shipping container and carefully remove the contents.

Step 2

Return all packing materials to the shipping container and save it.

Step 3

Ensure that all items listed in the Package Contents section are included in the shipment. Check each item for damage. If any item is damaged or missing, notify your authorized Cisco sales representative.

Note

The access point has two radio module slots: Slot 0 and Slot 1. Slot

0 can only be used with the 2.4-GHz radio module and slot 1 can only be used with the 5-GHz radio module. New radio configuration changes are associated with the specific module slot where the radio module is located. Once the default radio settings are changed, the radio modules should not be moved to a different slot. If you move the radio to a different slot, the radio configuration must be deleted and then remade.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

9

Before Beginning the Installation

Before you begin the installation, refer to the illustrations on the following pages to become familiar with the access point and the mounting hardware

Caution

Be careful when handling the access point; the bottom plate might be hot.

Caution

The access point must be located indoors within the same building, including the associated LAN connections.

The following illustrations show the access point and identify its features.

10

78-17831-01

1

2

3

6

4

ETHERNET STATUS RADIO

5

1

2.4-GHz radio antennas

2

2.4-GHz radio module

3

LEDs

4

5

6

5-GHz radio antennas

5-GHz radio module

Security lock slot (hidden)

Quick Start Guide: Cisco Aironet 1250 Series Access Point

11

This illustration shows LED placement.

ETHERNET STATUS RADIO

12

ETHERNET STATUS RADIO

78-17831-01

This illustration shows the bottom of the access point with the mounting plate removed.

48vDC ETHERNET CONSOLE MODE

1 2

1

Radio module latch

2

Ethernet cable bay

3 4

3

Console port cable bay

4

Radio module latch

Quick Start Guide: Cisco Aironet 1250 Series Access Point

13

This illustration shows the connections inside the Ethernet and console port bays.

CAUTION

EXTERNAL DC AND INLINE PoE

POWER SOURCE REQUIREMENTS

DETERMINED BY INSTALLED

RADIO MODULES

REFER TO

PRODUCT DOCUMENTATION

+56VDC ETHERNET

1

1

DC power receptacle

2

Ethernet port (RJ-45)

2

CONSOLE MODE

3 4

3

Console port (RJ-45)

4

Mode button

14

78-17831-01

Installation Summary

Installing the access point involves these operations:

Mounting the Access Point

Connecting Power

Obtaining and Assigning an IP Address

Configuring Power

Configuring Security Settings

Mounting the Access Point

Detailed mounting instructions are in the Cisco Aironet 1250 Series Access

Point Hardware Configuration Guide. This document is available on

Cisco.com.

UL 2043 Compliance

The access point has adequate fire resistance and low smoke-producing characteristics. The device is suitable for operation in a building’s environmental air space, such as above suspended ceilings. The access point complies with with Section 300-22(c) of the NEC and with Sections 2-128,

12-010(3), and 12-100 of the Canadian Electrical Code, Part 1, C22.1.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

15

Note

The 1250 series power injector, 1250 series DC power module, and antennas are not tested to UL 2043 and should not be placed in a building’s environmental air space.

Connecting Power

The access point can be powered locally by the 1250 DC power module or an

IEEE 802.3af compliant Power-over-Ethernet (PoE) power source. However, if the access point is powered by an 802.3af source, only one radio is supported because the two radio operation requires 18.5 watts. Two radio operation is supported only by the 1250 series power injector and an 802.at compliant PoE switch.

IEC60950 and IEEE 802.3af devices include:

A 1250 DC power module connected to the access point’s power connector

The 1250 DC power module should be plugged into a 100-240 VAC source

The following devices provide PoE:

An IEEE 802.af compliant power source

16

78-17831-01

An IEEE 802.3af compliant Cisco inline power switch

A Cisco 1250 series power injector (AIR-PWRINJ4)

Note

Some older switches and patch panels might not provide enough power to operate the access point. At power-up, if the access point is unable to detect sufficient power, the access point deactivates both radios to prevent an over-current condition, and the Status LED displays a low power error (cycles blue, green, red, and off).

When power is applied to the access point, it begins a routine power-up sequence that you can monitor by observing the three LEDs on top of the access point. When all three LEDs turn green to indicate the starting of the

IOS operating system, the Status LED blinks green signifying that IOS is operational. When in an operational status, the Ethernet LED is continuously green when no traffic is being passed and dark when traffic is being passed.

The sequence takes about 1 minute to complete. Refer to the “Checking the

Access Point LEDs” section on page 28 for LED descriptions.

When the sequence is complete, you can obtain the access point’s IP address and perform an initial configuration. Refer to the

“Obtaining and Assigning an IP Address” section on page 18 for instructions on assigning basic settings

to the access point.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

17

Note

If your access point is connected to in-line power, do not connect the power module to the access point. Using two power sources on the access point might cause the access point to shut down to protect internal components and might cause the switch to shut down the port to which the access point is connected. If your access point shuts down, you must remove all power and reconnect only a single power source.

Obtaining and Assigning an IP Address

To browse to the access point Express Setup page, you must either obtain or assign the access point IP address using these methods:

Assign a static IP address by connecting to its console port and opening the access point CLI.

Use a DHCP server (if available) to automatically assign an IP address.

You can find out the DHCP-assigned IP address by using one of the following methods:

Connect to the access point console port and use a Cisco IOS command such as show interface bvi1 to display the IP address.

18

78-17831-01

Provide your organization’s network administrator with your access point MAC address. Your network administrator will query the

DHCP server using the MAC address to identify the IP address. The

MAC address is on a label attached to the bottom of the access point.

Use the CLI and serial port to identify the assigned IP address.

Connecting to the Access Point Locally

If you need to configure the access point locally (without connecting it to a wired LAN), you can connect a PC to its console port by using a DB-9 to

RJ-45 serial cable.

Follow these steps to open the CLI by connecting to the access point console port.

Step 1

Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and to the COM port on the PC.

Step 2

Set up a terminal emulator on your PC to communicate with the access point. Use the following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

19

Assigning an IP Address Using the CLI

When you assign an IP address to the access point using the CLI, you must assign the address to the BVI. Beginning in a privileged EXEC mode, follow these steps to assign an IP address to the access point BVI using the console port:

Step 1

Step 2

Step 3

Step 4

Step 5

Command enable configure terminal

Interface bvi1

Purpose

Enter privileged EXEC mode.

Enter global configuration mode.

Enters interface configuration mode for the BVI.

ip address address mask Assigns an IP address and subnet mask address to the BVI.

end

Return to privileged EXEC mode.

Configuring Power

The access point receives power through the Ethernet cable or an external power module. The following illustration shows the power options for the access point.

20

78-17831-01

SYST

STAT UTIL

MODE

RPS

DUPLX

SPEED

Option 1

Switch

(with or without inline power)

10 11

10Base-T / 10

12

0Base-TX

13

14 15

16

17 18

19 20

21 22

23

24

Catalyst 2950

SERIES

23

100Base-FX

24

Power injector

Power cord

DC power module

Option 2

Access Point

Warning This product must be connected to a Power over Ethernet (PoE)

IEEE 802.3af compliant power source or an IEC60950 compliant limited power source. Statement 353

Quick Start Guide: Cisco Aironet 1250 Series Access Point

21

The access point power options:

Option 1—Switches with sufficient inline power (single radio only):

An inline power capable switch, such as the Cisco Catalyst 3550

PWR XL, 3560-48PS, 4500 with 802.3af PoE module, or the 6500 with 802.3af PoE module

Other inline power switches supporting the IEEE 802.3af inline power standard

Option 2—Switches without sufficient inline power can use the power injector (two radio operation):

– 1250 series power injector (AIR-PWRINJ4)

Option 3—Local power using the 1250 series DC power module

(AIR-PWRSPLY1)

Option 4—An 802.at compliant PoE switch

Note

Some older switches and patch panels might not provide enough power to operate the access point. At power-up, if the access point is unable to determine that the power source can supply sufficient power, the access point automatically deactivates both radios to prevent an over-current condition. The access point Status LED turns amber and an error log entry is created

22

78-17831-01

Connecting to an Ethernet Network with an Inline Power

Source

Caution

Be careful when handling the access point; the bottom plate might be hot.

Note

If your access point is connected to in-line power, do not connect the power module to the access point. Using two power sources on the access point might cause the access point to shut down to protect internal components and might cause the switch to shut down the port to which the access point is connected. If your access point shuts down, you must remove all power and reconnect only a single power source.

Follow these steps to connect the access point to the Ethernet LAN when you have an inline power source:

Step 1

Connect a Category 5E (or higher) Ethernet cable to the RJ-45

Ethernet connector labeled Ethernet on the access point.

Step 2

Step 2 Connect the other end of the Ethernet cable to one of the following:

Quick Start Guide: Cisco Aironet 1250 Series Access Point

23

A switch with inline power.

The Ethernet connector on the 1250 series power injector labeled To

AP.

Step 3

When using the power injector, connect a Category 5E (or higher)

Ethernet cable from your your inline power switch to the power injector connector labeled To Switch.

Step 4

When using the power injector, connect an AC power cord to the power injector and the AC wall socket.

Connecting to an Ethernet Network with Local Power

Note

If your access point is connected to in-line power, do not connect the

DC power module to the access point. Using two power sources on the access point might cause the access point to shut down to protect internal components and might cause the switch to shut down the port to which the access point is connected. If your access point shuts down, you must remove all power and reconnect only a single power source.

24

78-17831-01

Follow these steps to connect the access point to an Ethernet LAN when you are using a local power source:

Step 1

Connect a Category 5E (or higher) Ethernet cable to the RJ-45

Ethernet connector labeled Ethernet on the access point.

Step 2

Connect the 1250 series DC power module’s output connector to the access point’s DC-IN power connector.

Step 3

Plug the other end of the Ethernet cable into an unpowered Ethernet port on your LAN network.

Step 4

Plug the 1250 series DC power module’s AC power cord into an approved 100- to 240-VAC outlet.

Configuring the Access Point

How you configure your access point depends on how you intend to use it in your wireless network. This guide provides a brief synopsis of the configuration process. For detailed information, refer to the “Configuring the

Access Point for the First Time” chapter of the Cisco IOS Software

Configuration Guide for Cisco Aironet Access Points for the Cisco IOS release you are using.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

25

The following basic settings must be configured on your access point.

Host Name

Configuration Server Protocol

IP Address

IP Subnet Mask

Default Gateway

SNMP Community

The following radio settings must be applied separately to each radio.

Role in Radio Network

Optimize Radio Network For

Aironet Extensions

Configuring Security Settings

After you assign basic settings to your access point, you must configure security settings to prevent unauthorized access to your network. Because it is a radio device, the access point can communicate beyond the physical boundaries of your work site.

26

78-17831-01

Basic security settings are explained in the “Configuring the Access Point for the First Time” chapter of the Cisco IOS Software Configuration Guide for

Cisco Aironet Access Points for the Cisco IOS release you are using.

The following security settings are available on the Express Security Setup page.

No Security

Static WEP Key

EAP Authentication

WPA and WPA2

Advanced security settings are described in appropriate chapters of the Cisco

IOS Software Configuration Guide for Cisco Aironet Access Points for the

Cisco IOS release you are using.

Note

The 802.11n radio only supports no encryption, WPA2 Enterprise, and WPA-2 Personal. WPA-2 Enterprise and WPA-2 Personal requires AES encryption.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

27

In Case of Difficulty

If you followed the instructions in previous sections of this guide, you should have had no trouble getting your access point installed and running. If you do experience difficulty, the following sections provide basic troubleshooting information.

Before contacting Cisco, look for a solution to your problem in this guide or the “Troubleshooting” chapter of the Cisco Aironet 1250 Series Access Point

Hardware Installation Guide.

Follow this link to access the Technical Assistance Center (TAC) on

Cisco.com: http://www.cisco.com/cisco/web/support/index.html

Checking the Access Point LEDs

If your access point is not working properly, check the Status, Ethernet, and

Radio LEDs on the top panel. You can use the LED colors to assess the unit status.

The LED meanings are in the following table.

28

78-17831-01

Note

Regarding LED status colors, it is expected that there will be small variations in color intensity and hue from unit to unit. This is within the normal range of the LED manufacturer’s specifications and is not a defect.

Ethernet LED

Green

Blinking green

Radio LED

Blinking green

Blinking green

Status LED

Green

Blue

Meaning

Normal operation; no wireless clients associated.

Normal operation; at least one wireless client associated.

Ethernet link is operational.

Transmitting or receiving radio packets

Software upgrade in progress.

Blinking blue

Blinking green

Access location command.

Blinking red Ethernet link not operational in FlexConnect mode.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

29

Ethernet LED

Red

Amber

Radio LED

Blinking green

Blinking amber

Red

Red

Blinking amber

Red

Status LED

Red

Blinking blue

Blinking green

Meaning

Ethernet failure

Configuration recovery in progress (Mode button pressed for 2–3 seconds).

Image recovery in progress

(Mode button pressed for

20–30 seconds).

Ethernet transmit or receive errors.

Maximum retries or buffer full failure on radio.

Software failure.

Cycling blue, green, red, off

General warning; insufficient inline power.

For more details on these LED status codes, see the “Troubleshooting” chapter of the Cisco Aironet 1250 Series Access Point Hardware Installation

Guide.

30

78-17831-01

Resetting to Default Configuration

Note

These steps reset all configuration settings to factory defaults, including passwords, WEP keys, the IP address, and the SSID.

If you forget the password that allows you to configure the access point, you may need to completely reset the configuration. You can use the MODE button on the access point or your web browser to reset the configuration.

Using the MODE Button

Follow these steps to delete the current configuration and return all access point settings to the factory defaults:

Step 1

If the access point is mounted using its mounting plate, remove it to gain access to the MODE button.

Step 2

Disconnect power from the access point (the power jack for external power or the Ethernet cable for in-line power).

Step 3

Press and hold the MODE button while you reconnect power to the access point.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

31

Step 4

Continue holding the MODE button until the Ethernet LED turns amber (approximately 2 to 3 seconds), then release the button.

Step 5

After the access point reboots, you must reconfigure it using the web browser interface, the Telnet interface, or connecting to the access point console port.

Using the Web Browser Interface

Follow these steps to delete the current configuration and return all access point settings to factory defaults using the web browser interface:

Step 1

Open your Internet browser. You must use Microsoft Explorer

(version 5.x or later) or Netscape Navigator (version 4.x or later).

Step 2

Enter the access point IP address in the browser address line, and press Enter. An Enter Network Password window appears.

Step 3

Enter your username in the User Name field.

Step 4

Enter your password in the Password field and press Enter. The

Summary Status page appears.

Step 5

Click System Software. The System Software page appears.

Step 6

Click System Configuration. The System Configuration page appears.

32

78-17831-01

Step 7

Click the Reset to Defaults or Reset to Defaults (Except IP) button (depending on your configuration).

Step 8

After the access point reboots, reconfigure it.

Compliance Information

This equipment has been tested and found to comply with the European

Telecommunications Standard ETS 300.328. This standard covers Wideband

Data Transmission Systems referred to in CEPT recommendation T/R 10.01.

This type-accepted equipment is designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed in accordance with the instruction manual, may cause harmful interference to radio communications.

The Declarations of Compliance for this product relevant to the European

Union and other countries following EU Directive 1999/5/EC (R&TTE

Directive) can be found in the Cisco Aironet 1250 Series Access Point

Hardware Installation Guide. This guide is available on Cisco.com.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

33

Cisco 90-Day Limited Hardware Warranty

Terms

There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranties and license agreements applicable to Cisco software, is available on Cisco.com.

Follow these steps to access and download the Cisco Information

Packet and your warranty and license agreements from Cisco.com.

1.

Launch your browser, and go to this URL: http://www.cisco.com/en/US/products/prod_warranties_listing.html

The Warranties and License Agreements page appears.

2.

To read the Cisco Information Packet, follow these steps:

a. Click the Information Packet Number field, and make sure that the part number 78-5235-03B0 is highlighted.

b. Select the language in which you would like to read the document.

c. Click Go.

The Cisco Limited Warranty and Software License page from the

Information Packet appears.

34

78-17831-01

d. Read the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF).

Note

You must have Adobe Acrobat Reader to view and print

PDF files. You can download the reader from Adobe’s website: http://www.adobe.com

3.

To read translated and localized warranty information about your product, follow these steps:

a. Enter this part number in the Warranty Document Number field:

78-5236-01C0

b. Select the language in which you would like to read the document.

c. Click Go.

The Cisco warranty page appears.

d. Review the document online, or click the PDF icon to download and print the document in Adobe Portable Document Format (PDF).

You can also contact the Cisco service and support website for assistance: http://www.cisco.com/cisco/web/support/index.html

.

Duration of Hardware Warranty

Ninety (90) days.

Quick Start Guide: Cisco Aironet 1250 Series Access Point

35

Replacement, Repair, or Refund Policy for Hardware

Cisco or its service center will use commercially reasonable efforts to ship a replacement part within ten (10) working days after receipt of a Return

Materials Authorization (RMA) request. Actual delivery times can vary, depending on the customer location.

Cisco reserves the right to refund the purchase price as its exclusive warranty remedy.

To Receive a Return Materials Authorization (RMA) Number

Contact the company from whom you purchased the product. If you purchased the product directly from Cisco, contact your Cisco Sales and

Service Representative.

Complete the information below, and keep it for reference:

Company product purchased from

Company telephone number

Product model number

Product serial number

Maintenance contract number

36

78-17831-01

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals