AireRyder | LK40112AW | Instructions / Assembly | AireRyder LK40112AW Instructions / Assembly

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
LK40112/LK40162
AVOID RISK OF ELECTRICAL SHOCK. BE SURE TO SHUT OFF
WARNING: TO
POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1.Before installing, consult local electrical codes for wiring and grounding requirements.
2.The combined weight of your ceiling fan and light kit can not exceed 35 pounds unless
additional support is provided for the fan.
Nipple-1
Fixture
Fig.1
Motor
Coupling
Hex Nut
Switch Box
Hex Nut
Screw
Plug
Nipple-1
Nipple
Wire Nut
Washer
Tube
Switch Box cover
Tube Cap
Light kit
Metal Holder
Hex Nut
Screw
Wire Nut
Motor
Switch Box
Terminal(Groove)
Glass shade
Terminal(Tongue)
Switch Box cover
Nipple-1
Light kit
Metal Washer
Set Screw
Installation Steps
Pull Chain for Fan
Rubber Washer
Hex Nut
Cap
Finial
Pull Chain
1. Remove the switch box cover from the fan by loosing 3 screws.
2. Unscrew and discard the plug from the switch box cover.
3. Attach the light kit to the switch box cover.
***For fans of the Fig.1, please attach the nipple-1 of the light kit to the hole of the switch
box cover, and then thread the wires through the washer and hex nut, and secure tightly.
***For fans of the Fig.2, please attach the nipple-1 of the light kit to the hole in the center
of the switch box cover, and then secure with 2 set screws to the switch box cover.
4. Make wire connections with the wire nuts:
---Connect black or blue wire from light kit to blue wire from the fan.
---Connect white wire form light kit to white wire from the fan.
Carefully tuck wires back into the switch box cover.
5. Install the Nipple to the Coupling and adjust the length with the Hex Nut.
6. Install the Tube, Tube Cap and Metal Holder into the Nipple by the Hex Nut.
7. Reinstall the switch box cover with the 3 screws.
8. Install bulbs.( Please do not exceed the maximum capacity which is recommended on the
package.)
9. Thread the pull chain through the glass shade, rubber washer, metal
washer and hex nut in order, and secure with the hex nut to the nipple.
10. Thread the pull chain through the cap and finial, and secure with the finial to the nipple.
11. Thread the pull chain of the fan through the glass shade and the cap.
*** Make sure the hole of glass shade and the hole of the cap for fan was match.
12. Turn on the power at fuse or circuit box.
TM
LK40112/LK40162--- Page 1
070424
For Ceiling Light: (See Fig.1)
1. Take out the canopy set from the hardware package for
ceiling light.
2. Thread the fixture wires through the canopy set. Secure
the canopy set onto nipple(-a) by using the coupling.
4. Attach two screws to the mounting strap, then secure
them with two lock nuts. Adjust the length of the screws
if necessary.
5. Attach the mounting strap to the outlet box by using
two mounting screws.
6. Pull out the outlet wires and the house grounding wire
from the outlet box. Make wire connections using the
wire nuts:
---The black wire from fixture to the black wire from the
outlet box.
---The white wire from fixture to the white wire from the
outlet box.
---Attach the fixture grounding wire to the mounting strap
with the green grounding screw. Then connect it to the
house grounding wire with a wire nut.
Carefully tuck the wires back into the outlet box.
7. Attach canopy to the mounting strap by inserting the
screws, then secure them with the bolt nuts.
8. Follow steps 7~9 as for Light Kit.
Mounting Parts for Ceiling Light
Outlet Box
House Grounding Wire
Wire Nut
Screw
Mounting Strap
Lock Nut
Green Grounding Screw
Mounting Screw
Fixture Grounding Wire
Canopy Set
Bolt Nut
Coupling
Nipple(-a)
Cap(-a)
Fig.1
TM
LK40112/LK40162--- Page 2
070424
Download PDF