AireRyder | LK35454A/C-C | Instructions / Assembly | AireRyder LK35454A/C-C Instructions / Assembly

ASSEMBLY AND INSTALLATION
INSTRUCTIONS
LK35454
WARNING: BE SURE TO SHUT OFF POWER AT THE MAIN FUSE OR CIRCUIT
BREAKER BOX BEFORE INSTALLING OR SERVICING THIS FIXTURE.
NOTE: 1. Before installing, consult local electrical codes for wiring and grounding requirements.
2. The combined weight of your ceiling fan and light kit cannot exceed 35 pounds unless
additional support is provided for the fan.
Motor
Black or Blue Wire
Wire Nut
Smooth Wire
Switch Box
White Wire
Ridged Wire
Hex Nut & Washer
Switch Box Screw
Center Plug
For Light Kit:
Canopy
Switch Box Cover
Nipple(-a)
Set Screw
Bolt Nut
1. Remove the switch box cover from the switch
Arm(-a)
box of the fan by loosing the three switch box
screws.
Socket Ring
2. Unscrew the center plug from the switch box
cover and discard it.
3. Secure the rod to nipple(-b).
Glass Shade
4. Unscrew the bolt nuts from the set screws.
5. Attach a arm(-a) to the rod and a arm(-b)
according to the drawing of the package
Glass Holder
by inserting the set screws, then secure it
Rod
with the bolt nuts.
Nipple(-b)
Bolt Nut
Repeat with other arms(-a).
Fixture
Set Screw
6. Attach nipple(-a) of the light kit to the
Arm(-b)
switch box cover, then secure it with a
Pull Chain
washer and hex nut.
7. Cut the redundant wires if necessary. Pull
out the wires from the switch box. Make wire
connections using the wire nuts:
---The smooth (marked) wire from the fixture to the black (or blue) wire from the switch box.
---The ridged (unmarked) wire from the fixture to the white wire from the switch box.
Carefully tuck the wires back into the switch box.
8. Attach the switch box cover back to the switch box using the three switch box screws.
9. Attach the glass shades to the glass holders and secure them with the socket rings.
10. Install bulbs (not included). See relamping label at socket area or packaging for maximum allowed
wattage.
11. Turn on the power at the main fuse or circuit breaker box. (You can control the light with the pull chain.)
TM
LK35454 --- Page 1
060217
Loop
Hex Nut
Washer
Metal Pad
Top Cap
Grounding Pad
Cap
Washer
Cap
Pipe(-a)
Nipple(-a)
Pipe(-b)
Nipple(-a)
Cap
Cap
Holder
Holder
Fig.1
Fig.2
For Mini Chandelier: (See Fig.1, Fig.2 & Fig.3)
Mounting Parts for Mini Chandelier
1. Unscrew and take out the hex nut, washer, metal pad,
top cap, cap and pipe(-a) from nipple(-a). (See Fig.1)
Outlet Box
2. Take out the loop, grounding pad and pipe(-b) from the
House Grounding Wire
hardware package for Mini Chandelier.
Wire Nut
3. Attach pipe(-b), cap with the open side facing downward,
Hex Nut
Washer
washer and grounding pad to the holder by inserting
Mounting Strap
nipple(-a), then secure them with the loop. (See Fig.2)
Green Grounding Screw
Mounting Screw
4. Repeat the steps 3~5 for Light Kit.
Nipple(-c)
5. Choose the length of the chain you need, then weave the
fixture wire and the fixture grounding wire through the
Canopy
chain. Then connect one end of the chain with the loop by
Top Loop
using one loop lock.
Collar
6. Secure the top loop to nipple(-c).
Loop Lock
7. Thread the fixture wire and fixture grounding wire through
Fixture Grounding Wire
the collar, canopy, top loop, nipple(-c) and mounting strap.
8. Connect the other end of the chain with the top loop by
Chain
Loop Lock
using the other loop lock.
Fixture Wire
9. Pull out the outlet wires and the house grounding wire
Loop
from the outlet box. Make wire connections using the
Nipple(-d)
wire nuts:
---The smooth wire (marked) from the fixture to the
black wire from the power source.
Fig.3
---The ridged wire (unmarked) from the fixture to the
white wire from the power source.
---Attach the fixture grounding wire to the mounting strap with the green grounding screw. Then connect
it to the house grounding wire with a wire nut.
Carefully tuck the wires back into the outlet box.
10. Attach the canopy to the mounting strap by inserting the top loop, then secure it with the collar.
11. Repeat the steps 9~11 for Light Kit.
TM
LK35454 --- Page 2
060217
Download PDF