Casablanca | 99076 | Instructions / Assembly | Casablanca 99076 Instructions / Assembly

Wet-Rated
Low Profile Integrated Kit
Installation Manual
Models #99075, 99076,99077,99078, 99079
Compatible with:
2xxxx Types A - Z
51000-58999 fan series
59500-59999 fan series
Select Casablanca Fans
MA006-01 • 7/26/13
1.888.830.1326
BEFORE YOU BEGIN
Read entire installation instructions carefully before
beginning installation and save these instructions.
Switch
Housing
Your light kit is compatible with most ceiling fans. The light kit will attach to the fan’s
switch housing. Begin on page 3 where you will choose the type of switch housing that
most closely resembles the one on your fan. From there, you will be directed to the set of
assembly instructions that are appropriate for installing the light kit to your fan.
READ AND SAVE THESE INSTRUCTIONS
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal injury,
mount fan directly from building structure and/or an outlet box marked
acceptable for fan support of 70 lbs. (31.8 kg) and use the mounting screws
provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your
fan, disconnect the power by turning off the circuit breakers to the outlet
box and associated wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent warning device,
such as a tag, to the service panel.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes
ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
2
MA006-01 • 07/26/13
er
Pow
n
r
Tu
OFF
1.888.830.1326
WHICH ASSEMBLY METHOD WILL I USE?
Choose one of the four images below that most closely resembles the switch
housing on your fan; then follow the instructions under the image.
Cap
Screw
Switch
Housing
Screw
Switch
Housing
Cap
If your fan’s switch housing cap
resembles this one, remove the cap
screws with a Phillips head screwdriver.
Then follow the TYPE-A ASSEMBLY
INSTRUCTIONS on pages 4-5.
Switch
Housing
Screw
Switch
Housing
Cap
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
screws with a Phillips head screwdriver.
Remove the two cap screws from the
inside of the switch housing. Reinstall
the switch housing. Tighten the switch
housing screws. Then follow the TYPE-A
ASSEMBLY INSTRUCTIONS on pages 4-5.
Plug
Button
Plug
Button
If your fan’s switch housing cap
resembles this one, remove the whole
switch housing by removing the switch
housing screws with a Phillips head
screwdriver. Remove the plug button.
Then follow the TYPE-B ASSEMBLY
INSTRUCTIONS on pages 6-7.
Switch
Housing
Screw
If your fan’s switch housing cap resembles
this one, remove the whole switch
housing by removing the switch housing
screws with a Phillips head screwdriver.
Remove the plug button using a standard
screwdriver. Then follow the TYPE-C
ASSEMBLY INSTRUCTIONS on pages 8-9.
3
MA006-01 • 07/26/13
1.888.830.1326
TYPE-A ASSEMBLY INSTRUCTIONS
1
2
Switch
Housing
Wire
Connector
Mounting
Screw
Feed the wires through the center hole
in the gasket. Then partially install the
two mounting screws through the
gasket into the bottom of the lower
switch housing. Press the gasket flush to
the lower switch housing.
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
3
4
Mounting
Screw
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
Keyhole
Slots
Lift the light kit up to meet the
lower switch housing. Wrap keyhole
slots around the screws and twist
counterclockwise. Tighten screws.
4
MA006-01 • 07/26/13
Do not allow the light kit to hang
only by the wire connections!
1.888.830.1326
TYPE-A ASSEMBLY INSTRUCTIONS (CONTINUED)
5
6
Tab
Bulb
Indentation
Socket
Installing the bulbs - Install a bulb
into each of the sockets. When
necessary, replace with bulbs of same
type and wattage.
Installing the globe (sold separately)Position the indentations in the outer rim of
the globe so that they line up with the tabs
on the inside surface of the light fixture rim.
Carefully lift the globe up inside the light
fixture as far as it will go. Rotate the globe in
a clockwise direction until it is held tightly
in place by the four tabs.
8
7
er
ow
P
rn
Tu
Installing the pull chain pendant Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
ON
Turn power on. Your installation
is complete!
5
MA006-01 • 07/26/13
1.888.830.1326
TYPE-B ASSEMBLY INSTRUCTIONS
1
2
Switch
Housing
Wire
Connector
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
Feed the wires through the center hole in
the switch housing, the washer, and the nut.
Push the center hole in the gasket over the
threaded rod of the light kit. Then install the
switch housing by twisting clockwise onto
the threaded rod. Install the washer and nut
onto threaded rod and tighten securely.
3
4
Switch
Housing
Screw
Using the single pin connectors, connect
the black or blue wire from the fan to the
black wire from the light kit. Connect the
white wire from the fan to the white wire
from the light kit.
Lift the light kit assembly up so that the
screw holes in the lower switch housing
line up with the holes in the upper switch
housing. Install the switch housing
screws and tighten securely.
6
MA006-01 • 07/26/13
Do not allow the light kit to hang
only by the wire connections!
1.888.830.1326
TYPE-B ASSEMBLY INSTRUCTIONS (CONTINUED)
5
6
Tab
Bulb
Indentation
Socket
Installing the bulbs - Install a bulb
into each of the sockets. When
necessary, replace with bulbs of same
type and wattage.
Installing the globe (sold separately)Position the indentations in the outer rim of
the globe so that they line up with the tabs
on the inside surface of the light fixture rim.
Carefully lift the globe up inside the light
fixture as far as it will go. Rotate the globe in
a clockwise direction until it is held tightly
in place by the four tabs.
7
8
er
ow
P
rn
Tu
Installing the pull chain pendant Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
ON
Turn power on. Your installation
is complete!
7
MA006-01 • 07/26/13
1.888.830.1326
TYPE-C ASSEMBLY INSTRUCTIONS
1
Switch
Housing
2
Wire
Connector
If your fan does not have pin connectors
on the wires coming from the switch
housing, install the wiring harness
provided. Using the provided wire
connectors connect the white wire from
the fan to the white wire from the wire
harness and connect the black or blue
wire from the fan to the black wire from
the wire harness.
Feed the wires through the center hole in
the switch housing. Then using the single
pin connectors, connect the black or blue
wire from the fan to the black wire from
the light kit. Connect the white wire from
the fan to the white wire from the light kit.
3
4
Lower
Switch
Housing
Upper
Switch
Housing
Threaded
Rod
Switch
Housing
Screw
Lift the lower switch housing up so that the
screw holes line up with the holes in the
upper switch housing. Install the switch
housing screws and tighten securely.
Lift the light kit up, tucking the wires into
the hole in the switch housing. Install the
center stem of the light kit into the lower
switch housing by turning the threaded
rod clockwise into the threaded hole.
Continue turning until tight.
8
MA006-01 • 07/26/13
Do not allow the light kit to hang
only by the wire connections!
1.888.830.1326
TYPE-C ASSEMBLY INSTRUCTIONS (CONTINUED)
5
6
Tab
Bulb
Indentation
Socket
Installing the bulbs - Install a bulb
into each of the sockets. When
necessary, replace with bulbs of same
type and wattage.
Installing the globe (sold separately)Position the indentations in the outer rim of
the globe so that they line up with the tabs
on the inside surface of the light fixture rim.
Carefully lift the globe up inside the light
fixture as far as it will go. Rotate the globe in
a clockwise direction until it is held tightly
in place by the four tabs.
7
8
er
ow
P
rn
Tu
Installing the pull chain pendant Attach the pull chain pendant to the
end of the short chains coming from the
switch housing and the light kit.
ON
Turn power on. Your installation
is complete!
9
MA006-01 • 07/26/13
1.888.830.1326
TROUBLESHOOTING
Lights don’t come on.
• Make sure that the bulbs are properly installed.
• Make sure power switch is on.
• Pull the pull chain to make sure it is on.
• Check the circuit breaker to ensure the power is turned on.
• Check the pin connections in the light kit.
• Refer to the fan manual for locating the fan’s wiring. Verify that the light and power
wires are correctly connected to the ceiling and the light kit.
ONE YEAR WARRANTY
This product is warranted to the original purchaser by Casablanca Fan Company/
Hunter Fan Company against defects in material and workmanship for one (1)
year from date of purchase. During the warranty period, we will repair or, at our
option, replace a defective product at no charge. For information on how to obtain
service, contact the Casablanca/Hunter Service Department by calling our tollfree number at 888-830-1326. Damage to the product caused by mishandling,
improper installation or modification is not covered by this warranty. This warranty
is given in lieu of all other warranties expressed or implied. Some states do not allow
limitations of time on an implied warranty, therefore the above limitations may not
apply in every case. This warranty states specific legal rights which may vary from
state to state.
If you have problems installing or operating your light kit, do not return this product
to the dealer. Call our Consumer Affairs Hotline.
888-830-1326
Monday through Friday
8:00 am to 4:30 pm Central
10
MA006-01 • 07/26/13
Download PDF