Sea gull lighting | 6614-185 | Installation guide | Sea Gull Lighting 6614-185 Installation Guide

Installation And Safety Instructions
HC-362
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
123098
ASSEMBLY
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR
THE CIRCUIT BREAKER SET AT OFF.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
STEP 1:
GENERAL
You don't need special tools to install this fixture.Be sure to follow the
steps in the order given.Under no circumstances should a fixture be
hung on house electrical wires, nor should a swag type fixture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualified electrician.
*OUTLET BOX
*GROUND WIRE
*WIRE CONNECTOR
Attach fixture loop (H) to top plate (J) (if applicable).
GROUNDING AND MOUNTING BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
MOUNTING BAR (A)
*WIRE
CONNECTORS
*OUTLET BOX SCREWS
NUT (B)
NIPPLE (C)
MOUNTING
BAR (A)
GROUND WIRE (M)
SCREW COLLAR (E)
CANOPY (G)
SCREW COLLAR RING (F)
CHAIN (P)
FIXTURE LOOP (H)
TOP PLATE (J)
SUPPORT ARM (Y)
RUBBER SUPPORT
WASHER (L)
GLASS (O)
METAL
WASHER (Z)
FIGURE 1
*NOT INCLUDED
BALL NUT (M )
*OUTLET BOX
SCREWS
GREEN
GROUNDING
SCREW (D)
FIGURE 2
*NOT INCLUDED
NUT (B)
NIPPLE (C)
INSTALLATION
HC-362
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) on nipple (C) so that three threads are
exposed above nut (B). Thread nipple (C) into mounting bar (A) and
secure with nut (B). Attach screw collar (E) to nipple (C).
STEP 2:
Using two pairs of pliers, open one link of chain (P) and connect it to
the fixture loop (H) at the top of the fixture.
STEP 3:
Slide the screw collar ring (F) and canopy (G), in that order, over
chain (P). Open one link on the other end of the chain (P) and
attach it to the screw collar (E) which has been mounted to the
ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
STEP 4:
Lace wires up through chain (P) and pass wires through holes in
screw collar (E). We recommend lacing wire up through every other
link of chain (P).
STEP 5:
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 6:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire (M) from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated wire is on the mounting bar (A),
connect the ground wire (M) from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 1:
After wires are connected, tuck them carefully inside outlet box.
Raise canopy (G) against ceiling and screw the screw collar ring (F)
to the screw collar (E).
STEP 2:
Install lamps.
STEP 3:
On support arm (Y) place: rubber support washer (L), glass diffuser (O),
metal washer (Z) and secure with ball nut (M).
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool, or abrasive paper.
ORDERING PARTS
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER
BROWN, GOLD OR BLACK WITH TRACER
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF