INSTALLATION AND SAFETY INSTRUCTIONS BEFORE YOU BEGIN IMPORTANT SAFETY INSTRUCTIONS • • • • • • • • Be sure the electricity to the system you are working on is turned off; either the fuse removed or the circuit breaker set at off. Use of other manufacturers components will void warranty, listing and create a potential safety hazard. If you are unclear as to how to proceed, contact a qualified electrician. You don't need special tools to install this fixture. Be sure to follow the steps in the order given. Read instructions carefully. To reduce the risk of fire, electric shock, or personal injury, mount to outlet box or supporting system able to support the weight of the fixture Save these instructions. *OUTLET BOX *HOUSE GROUND WIRE *WIRE CONNECTORS Carefully remove the fixture from the carton and check that all parts are included, as shown in Figure 1 & 2. Be careful not to misplace any of the screws or parts which are needed to install this fixture. STEP 1: Attach fixture loop (K) to top of fixture. GROUNDING AND MOUNTING BAR LOCK UP *OUTLET BOX MOUNTING BAR (A) *HOUSE GROUND WIRE *OUTLET BOX SCREWS NUT (B) NIPPLE (C) *WIRE CONNECTORS GROUND WIRE (F) COLLAR (E) MOUNTING BAR (A) CANOPY (H) *OUTLET BOX SCREWS COLLAR RING (I) GREEN GROUNDING SCREW (D) CHAIN (J) FIXTURE LOOP (K) SHADE (G) GLASS SUPPORT RING (M) GLASS RETAINING FIGURE 1 RING (L) *NOT SUPPLIED NUT (B) NIPPLE (C) FIGURE 2 *NOT INCLUDED Installation And Safety Instruction HC-1324 012808 Fill In Item Number On Carton And File This Sheet For Fixture Reference. ITEM#_______________ Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. INSTALLATION HC-1324 IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX. STEP 1: Secure mounting bar (A) to outlet box with outlet box screws (not supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed above nut (B). Thread nipple (C) into mounting bar (A) and secure with nut (B). Attach collar (E) to nipple (C). STEP 5: GROUNDING INSTRUCTIONS: The green grounding screw (D) is to be inserted into the hole with two raised dimples provided on the mounting bar (A). Wrap the ground wire (F) from the fixture and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (D) on the mounting bar (A) if uninsulated wire is on the mounting bar (A), connect the ground wire (F) from the fixture and the outlet box to it using a small wire connector (not supplied). NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. STEP 2: Using 2 pairs of pliers, open one link of chain (J) and connect it to the fixture loop (K) at the top of the fixture. FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors. STEP 3: Slide the collar ring (I) and canopy (H), in that order, over chain (J). Open one link on the other end of the chain (J) and attach it to the collar (E) which has been mounted to the ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY. STEP 4: STEP 1: After wires are connected, tuck them carefully inside outlet box and then raise the canopy (H) against ceiling and thread the collar ring (I) to the collar (E). STEP 2: A. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below: Raise shade (G) over socket and secure by placing glass support ring (M) onto socket and threading glass retaining ring (L) onto socket. STEP 3: Install lamp. CLEANING To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper. ORDERING PARTS GROUP A: CONNECT TO BLACK HOUSE WIRE BLACK *PARALLEL WIRE (ROUND & SMOOTH) GROUP B: CONNECT TO WHITE HOUSE WIRE WHITE *PARALLEL WIRE (SQUARE & RIDGED) *Note: When parallel wire is used, the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth. (Seen best when viewed from wire end.) To separate wires, grasp the ends of each wire and pull apart. B. Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. DO NOT twist wires together before using wire connectors. C. Fit a wire connector (not supplied) over the wires and thread the connector clockwise until you feel a firm resistance. D. Gently try to remove the wires from the connector. If you can remove the wires, carefully re-do steps B and C, as above and check again for a firm connection. E. Connect the fixture wire from group B to the white wire from the outlet box in the same manner. Keep this sheet for future reference, and in case you need to order replacement parts. Parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.