Sea gull lighting | 69050BLE-962 | Installation guide | Sea Gull Lighting 69050BLE-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Proper wiring is essential to the safe operation of this fixture.
Save these instructions.
GROUNDING AND MOUNTING
BAR LOCK UP
*OUTLET BOX
*GROUND WIRE
MOUNTING
BAR (C)
GREEN
GROUNDING
SCREW (D)
MOUNTING
SCREWS (I)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
FIGURE 1
*NOT SUPPLIED
*WIRE
CONNECTORS
*NOT INCLUDED
*OUTLET BOX
SCREWS (K) FIGURE 2
*OUTLET BOX
LOCK WASHER (H)
CANOPY (G)
CAP NUTS (F)
NIPPLE (M)
MOUNTING
SCREWS (I)
CANOPY LOOP (S)
*WIRE
CONNECTORS
CHAIN (Y)
FOR STEM MOUNT
HEX NUT (W)
CANOPY (G)
CAP NUTS (F)
COUPLING (J)
ROD ASSEMBLY (E)
FIXTURE LOOP (X)
SOCKET ASSEMBLY (U)
FIGURE 3
ASSEMBLY FOR CHAIN HUNG
STEP 1:
THUMB SET
SCREW (A)
SOCKET
ASSEMBLY (U)
Thread nipple (M) through canopy loop(s). Install canopy loop(s) through
canopy (G), secure with lockwasher (H) and nut (W) (if applicable).
STEP 2:
Install fixture loop (X) onto socket assembly (U).
DIFFUSER (R)
STEP 3:
Feed the fixture wire from the socket assembly (U), through the fixture
loop (X), and canopy loop (S) (mounted on canopy (G)).
Note: This fixture can be hung using 1, 2, or 3 rods.
Select the number of rods desired.
FOR STEM MOUNT
STEP 1:
Secure rods together (if applicable).
STEP 2:
Feed the fixture wire from the socket assembly (U), through: the rod
assembly (E), and coupling (J) (mounted on canopy (G)).
STEP 3:
Secure rod assembly (E) to coupling (J), and socket assembly (U). Be
sure not to damage the fixture wire.
Installation And Safety
Instruction
HC-1327 112707
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_______________
HC-387
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
FOR STEM MOUNT AND CHAIN HUNG
STEP 1:
Insert fixture mounting screws (I) in threaded holes of mounting bar
(C). Run screws all the way down to the heads.
STEP 2:
Place mounting bar (B) against outlet box (not supplied) and fasten
mounting bar, through slots in mounting bar (B), to outlet box with
outlet box screws (K) (not supplied). Be sure the mounting screws are
perfectly horizontal so fixture hangs straight.
FOR CHAIN HUNG ONLY
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 2:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar. Wrap the ground wire from the fixture (if supplied) and the
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (D) on the mounting bar. If
uninsulated wire is on the mounting bar, connect the ground wire
from the fixture (if supplied) and the outlet box to it using a small
wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
Using 2 pair of pliers, open one link of chain (Y) and connect it to the
fixture loop (X) at the top of the fixture.
BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY.
STEP 2:
Lace fixture wire up through entire chain (Y) and pass through canopy
loop (S). We recommend lacing wire up through every other link of
chain (Y).
FOR STEM MOUNT AND CHAIN HUNG
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against ceiling allowing for mounting
screws (I) to protrude through holes in canopy (G). Secure in place
with cap nuts (F).
STEP 2:
WIRING
Place diffuser ring (Z) over diffuser (R) (if applicable). Raise diffuser
(R) to socket assembly (U). Secure with retaining ring (T).
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according to
the directions below:
STEP 3:
Install lamp.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
*NOTE: For Solid Copper Fixtures
Use a good quality automotive wax at least twice a year to protect
your fixture. If this additional care is not taken, your fixture will turn
into a Patina Finish over time.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
FIXTURES WITH A
ONE PIECE LAMP /
BALLAST
ONE PIECE
COMBINATION LAMP/
BALLAST
COMBINATION
LAMP (A)
*NOTE: When parallel wire is used, the tracer wire is square shaped or
ridged, and the less tracer wire is round in shape or smooth. (Seen best
when viewed from wire end.) To separate wires, grasp the ends of each
wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do steps B and C, as above, and check
FIGURE 3
SOCKET (B)
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF