Sea gull lighting | 94552-965 | Installation guide | Sea Gull Lighting 94552-965 Installation Guide

LR-145
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this
fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
For use with the 120V Transitions track series by Sea Gull Lighting.
Caution–To reduce the risk of a burn during relamping, remove from
the track before relamping.
Minimum distance from the front of the lamp to combustible
surfaces is 8".
Make sure all connections are tight.
Dimming halogen lamps greatly reduces lamp life.
To reduce the risk of FIRE or INJURY TO PERSONS: Turn off and
allow to cool before replacing lamp.
Turn off and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact switch only when turning on.
Do not touch hot lens, guard, or enclosure.
Do not touch the lamp at any time. Use a soft cloth. Oil from skin
may damage lamp.
Keep lamp away from materials that may burn.
Do not operate the luminaire fitting with a missing or damaged
shield.
Save these instructions.
ADAPTER CAP (A)
RAIL
STRAIN
RELIEF
SCREW (P)
1. Determine length of pendant and shorten cable from the splice
compartment (I). Be sure to add 5" for electrical connections
when installing with canopy (G).
2. Unthread top of splice compartment (I). Set strain relief collar at
desired location. NOTE: Strain relief collar is threaded and should
be threaded up and down cable. Be sure ³⁄₈" of cable jacket is
protruding out of strain relief collar. Secure in place by tightening
the two set screws.
3. Make connections between socket leads and pendant cable
using wire nuts inside the splice compartment:
a. Black to Black
b. White to White
c. Ground to Ground
Make sure no wires are left exposed and carefully tuck wire nuts
into bottom half of splice compartment (I).
4. Close splice compartment (I) by threading the two halves
together.
5. Install optional shade (not included) over socket (Q). Follow
applicable instructions provided with shade.
6. Install lamp (MRC16 GU10 50 watt not supplied) into socket (Q).
*OUTLET
BOX
RAIL
ADAPTER (R)
CANOPY
(G)
COLLAR (J)
SPLICE
COMPARTMENT
(I)
STEM (M)
SOCKET (Q)
*LAMP
*NOT INCLUDED
FIGURE 1
ASSEMBLING PENDANT/SHORTENING PENDANT
072808
GROUNDING AND MOUNTING BAR
LOCK UP FOR OPTIONAL
MONO-POINT CANOPY
*OUTLET BOX
WIRE
CONNECTORS
*GROUND WIRE
*OUTLET BOX
SCREWS
NIPPLE (V)
STRAIN RELIEF (H)
MOUNTING
BAR (F)
LOCKWASHER
& HEXNUT (U)
MONO-POINT
CANOPY (G)
COLLAR (O)
FIGURE 2
*NOT INCLUDED
FOR MONO-POINT INSTALLATION (Fig.2)
FIXT-I
S
FIXTURE
INSTALLATION
FIXT-IN
ST.
FIXT-IN
ST.
INC
ORRE
FIXT-IN
ST.
CORRECT
INC
ORRECT
CORRECT
INCORRECT
CORRECT
LR-145
1. Remove rail adapter (R) by cutting wire just below the rail adapter
(R).
2. Slide collar (O), canopy (G), mounting bar (F), nipple (V), and
lockwasher & hexnut (U), over wire to the top of the splice
compartment (I) (in that order).
3. Install strain relief (H) to wire. Tighten strain relief set screws with
a flat head screwdriver.
4. Secure mounting bar (F) to outlet box with outlet box screws (not
supplied).
5. Make electrical connections using silicone wire nuts or other UL
listed device. Be sure that no wires are left exposed.
a. House Black to Fixture Black
b. House White to Fixture White
c. House Ground to Green Ground Screw
Make sure that no wires are left exposed.
6. Raise canopy (G) against ceiling and secure by threading collar
(O) to nipple (V).
ADAPTER
CAP (A)
CONTACTS (K)
CONTACTS (K)
ADAPTER
CAP (A)
ATTACH PENDANT TO RAIL – REFER TO FIGURE 3
1. Unthread adapter cap (A) from rail adapter (R).
2. Making sure contacts (K) will align with conductors (L) on
rail, set the bottom of the the rail adapter (R) to the bottom
of the rail and “roll” rail adapter (R) up onto the rail.
3. Install fixture to rail by closing rail adapter (R) over rail. Thread
adapter cap (A) back onto rail adapter (R) tightly.
CONDUCTOR (L)
FIGURE 3
CONDUCTOR (L)
Download PDF