Sea gull lighting | 61850BLE-965 | Installation guide | Sea Gull Lighting 61850BLE-965 Installation Guide

HC-1302
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
FOR STEM MOUNT – REFER TO FIGURE 1
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
FOR STEM MOUNT
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE
NUMBER OF RODS
DESIRED.
MOUNTING BAR (A)
NUT (B)
NIPPLE (C)
CANOPY (G)
SCREW COLLAR (M)
COUPLING (J)
012208
*OUTLET BOX
*WIRE
CONNECTORS
GREEN
GROUNDING
SCREW (D)
*OUTLET BOX
SCREWS
CAP NUTS (F)
SCREW COLLAR
RING (O)
ROD ASSEMBLY (E)
Secure mounting bar (A) to outlet box using outlet
box screws (not provided). Thread nut (B) onto nipple
(C) so five threads are exposed. Thread nipple (C) to mounting bar
(A) and secure by threading nut (B) to mounting bar (A) Thread
screw collar (M) to nipple (C).
STEP 1:
STEP 2:
Secure rods together.
Feed the fixture wire from the socket assembly (U),
through: the rod assembly (E) and thread rod
assembly (E) into the socket assembly (U). Slide screw collar ring
(O) to socket assembly (U). Continue to feed wire through coupling
(J) (mounted on canopy (G)), and screw collar (M).
STEP 3:
STEP 4:
Secure rod assembly (E) to coupling (J). Be sure not
to damage the fixture wire.
GROUNDING
AND
MOUNTING
BAR
LOCK
UP
*OUTLET BOX
*GROUND WIRE
*WIRE
CONNECTORS
GREEN
GROUNDING
SCREW (D)
FIGURE 2
MOUNTING
BAR (A)
*OUTLET
BOX
SCREWS
NUT
(B)
NIPPLE (C)
*NOT SUPPLIED
NUT (B)
CANOPY
(G)
NIPPLE (C)
CANOPY LOOP (S)
CHAIN (Y)
FIXTURE LOOP (X)
DIFFUSER (R)
FIGURE 1
*NOT SUPPLIED
SOCKET ASSEMBLY (U)
RETAINING RING (T)
FIGURE 3
ASSEMBLY FOR CHAIN HUNG – REFER TO FIGURE 2 & 3
Secure mounting bar (A) to outlet box using outlet box
screws (not provided). Thread nut (B) to nipple (C) so
five threads are exposed. Thread nipple (C) to mounting bar (A) and
secure by threading nut (B) to mounting bar (A).
STEP 1:
STEP 2:
STEP 3:
Install fixture loop (X) onto socket assembly (U).
Feed the fixture wire from the socket assembly (U),
through the fixture loop (X).
INSTALLATION
HC-1302
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
FOR CHAIN HUNG ONLY
STEP 1:
Using 2 pair of pliers, open one link of chain (Y) and connect it to the
fixture loop (X) at the top of the fixture. Slide collar ring (O) and
canopy (G) to top of fixture.
STEP 2:
Lace fixture wire up through entire chain (Y) and pass through
canopy loop (S). We recommend lacing wire up through every
other link of chain (Y).
STEP 3:
Using 2 pair of pliers open one link of chain on the other end of
chain (Y) and connect it to the canopy loop (S). BE SURE TO
CLOSE ALL CHAIN LINKS COMPLETELY.
WIRING
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. DO NOT twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread
the connector clockwise until you feel a firm resistance.
D. Gently try to remove wires from connector. If you can remove
wires, carefully re-do steps B and C, as above and check again for a
firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
STEP 2:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is
to be inserted into the hole with two raised dimples provided on the
mounting bar. Wrap the ground wire from the fixture (if supplied) and
the ground wire from the outlet box (bare metal or green insulated
wire) around the green grounding screw (D) on the mounting bar.
If uninsulated wire is on the mounting bar, connect the ground wire
from the fixture (if supplied) and the outlet box to it using a small
wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against ceiling and secure by threading
screw collar ring (O) to screw collar (M).
STEP 2:
Raise diffuser (R) to socket assembly (U). Secure by threading
retaining ring (T) onto socket.
Install lamp.
STEP 3:
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.
CLEANING
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
ORDERING PARTS
Download PDF