Sea gull lighting | 61625-962 | Installation guide | Sea Gull Lighting 61625-962 Installation Guide

Installation And Safety Instructions
HC-1562
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
091009
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Save these instructions.
*OUTLET BOX
*WIRE
CONNECTORS
MOUNTING
BAR (A)
GREEN GROUNDING
SCREW (D)
NUT (C)
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
NIPPLE (I)
CANOPY (G)
SCREW COLLAR (B)
COUPLING (J)
SCREW COLLAR
RING (K)
ROD ASSEMBLY (E)
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
STEP 1:
Feed the fixture wire through the fixture loop (F) and thread fixture
loop (F) to top of socket assembly (U).
INSTALLATION
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Secure mounting bar (A) to outlet box using outlet box screws (not
supplied). Thread nut (C) onto nipple (I) so five threads are exposed.
Thread nipple (I) to mounting bar (A) and secure by tightening nut (C)
to mounting bar (A). Thread screw collar (B) to nipple (I).
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
FIXTURE LOOP (F)
SOCKET
ASSEMBLY (U)
STEP 2:
Assemble rod assembly (E) by threading desired amount of rods
together.
SHADE (R)
STEP 3:
Feed the fixture wire from the fixture loop (F), through: the rod
assembly (E) and thread rod assembly (E) into fixture loop (F). If using
optional chain, thread coupling at one end of chain into rod assembly
(E) or fixture loop (F)).
RETAINING RING (T)
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-1562
STEP 4:
Slide screw collar ring (K) and canopy (G) (in that order) to top of
socket assembly (U). Be sure not to damage the fixture wire. Thread
remaining end of rod assembly (E) or chain coupling to nipple of the
coupling (J) at the screw collar (B).
*OUTLET BOX
WIRING
STEP 5:
A. Use a listed wire connector to connect the fixture hot wire (black
wire, or round and smooth tracer) to the supply hot wire.
B. Use a listed wire connector to connect the fixture common wire
(white wire, or square and rigid) to the supply common wire.
C. Gently try to remove the wires from the connector. If you can
remove the wires, carefully re-do the wiring connection.
*WIRE
CONNECTORS
MOUNTING
BAR (A)
GREEN GROUNDING
SCREW (D)
NUT (C)
STEP 6:
NIPPLE (I)
GROUNDING INSTRUCTIONS:
Connect the supply ground wire, fixture ground wire, and mounting bar
ground wire (pre attached) using the supplied wiring connector. Gently try
to remove the wires from the connector. If you can remove the wires,
carefully re-do the wiring connection.
CANOPY (G)
SCREW COLLAR (B)
COUPLING (J)
SCREW COLLAR
RING (K)
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
CHAIN (M)
STEP 7:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against the ceiling. Secure by threading
screw collar ring (K) onto screw collar (B).
STEP 8:
ROD ASSEMBLY (E)
Place shade (R) securely in socket assembly (U). Secure by
threading retaining ring (T) onto socket.
STEP 9:
Install lamp.
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
SOCKET
ASSEMBLY (U)
SHADE (R)
RETAINING RING (T)
FIGURE 2
*NOT INCLUDED
Download PDF