Sea gull lighting | 61225-962 | Installation guide | Sea Gull Lighting 61225-962 Installation Guide

Installation And Safety Instructions
HC-1320
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
IMPORTANT SAFETY INSTRUCTIONS
112008
CLEANING
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
•
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
•
If you are unclear as to how to proceed, contact a qualified
electrician.
•
You don’t need special tools to install this fixture.
•
Be sure to follow the steps in the order given.
•
Read instructions carefully.
•
Save these instructions.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
FOR STEM MOUNT – REFER TO FIGURE 1
NOTE: THIS FIXTURE
CAN BE HUNG USING
1, 2, OR 3 RODS.
SELECT THE NUMBER
OF RODS DESIRED.
*OUTLET BOX
*WIRE
CONNECTORS
MOUNTING
BAR (A)
STEP 1:
Secure mounting bar (A) to outlet box using outlet box screws (not
provided). Thread nipple (C) into mounting bar (A) so 5 threads are
past mounting bar (A). Secure by threading nut (B) onto nipple (C)
and to mounting bar (A). Thread screw collar (I) to nipple (C).
STEP 2:
NUT (B)
NIPPLE (C)
CANOPY (G)
COLLAR RING (J)
SCREW
COLLAR (I)
SWIVEL JOINT
SET SCREW (Z)
ROD
ASSEMBLY (E)
Assemble rod assembly (E) by threading desired amount of rods together.
STEP 3:
Feed the fixture wire from the socket assembly (U), through the rod
assembly (E) and thread rod assembly (E) into socket assembly (U).
Slide collar ring (J) and canopy (G) (in that order) over rod assembly
(E). Continue to feed wire through screw collar (I) and nipple (C).
STEP 4:
Thread remaining end of rod assembly (E) onto coupling of screw
collar (I).
SOCKET
ASSEMBLY (U)
SHADE (R)
RETAINING
RING (T)
*NOT SUPPLIED
FIGURE 1
CANOPY (G)
NUT (B)
NIPPLE (C)
CANOPY LOOP (S)
COLLAR RING (J)
CHAIN (Y)
ASSEMBLY FOR CHAIN HUNG – REFER TO FIGURE 2
STEP 1:
Secure mounting bar (A) to outlet box using outlet box screws (not
supplied).
STEP 2:
Thread nipple (C) into mounting bar (A) so 5 threads are past
mounting bar (A). Secure by threading lockwasher & nut (B) to
mounting bar (A). Thread screw collar (I) to nipple (C). Thread canopy
loop (S) to nipple (C).
STEP 3:
Install fixture loop (X) onto socket assembly (U).
FIXTURE LOOP (X)
SOCKET ASSEMBLY (U)
FIGURE 2
STEP 4:
Feed the fixture wire from the socket assembly (U) through the fixture
loop (X).
INSTALLATION
HC-1320
FOR CHAIN HUNG
STEP 1:
Using 2 pair of pliers, open one link of chain (Y) and connect it to the
fixture loop (X) at the top of the fixture.
STEP 2:
Lace fixture wire up through entire chain (Y) and pass through
canopy loop (S). We recommend lacing wire up through every other
link of chain (Y). Slide collar ring (J) and canopy (G) to socket
assembly (U).
STEP 2:
GROUNDING INSTRUCTIONS: The green grounding screw (D) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (D) on the
mounting bar (A). If uninsulated wire is on the mounting bar (A),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 3:
Using 2 pairs of pliers open the other end of the chain and attach
that to the canopy loop (S). BE SURE TO CLOSE ALL CHAIN
LINKS COMPLETELY.
STEP 1:
After wires are connected, tuck them carefully inside outlet box and
then raise the canopy (G) against ceiling and secure by threading
collar ring (J) to screw collar (I).
WIRING
STEP 2:
STEP 1:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
When using stem mount method on sloped ceilings: Loosen swivel
joint set screws so rod assembly (E) hangs perpendicular to the floor.
Tighten swivel joint set screws (Z) to secure.
STEP 3:
Place shade (R) onto socket assembly (U) and secure by threading
retaining ring (T) onto socket.
STEP 4:
Install lamp.
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Download PDF