advertisement
*OUTLET BOX
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
HC-893
052307
RETAINING RING (B)
MOUNTING BAR (J)
GREEN
GROUNDING
SCREW (G)
GROUND
WIRE
SHADE (A)
CANOPY (D)
MOUNTING
SCREWS (F)
*WIRE CONNECTORS
FIGURE 1
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP
GREEN
GROUNDING
SCREW (G)
MOUNTING
SCREWS (F)
*OUTLET BOX
SCREWS
GROUND
WIRE
*OUTLET BOX
FIGURE 2
UNIVERSAL
MOUNTING BAR (E)
*WIRE CONNECTOR
*NOT SUPPLIED
CAP NUTS (C)
*NOT SUPPLIED
IMPORTANT SAFETY INSTRUCTIONS
• Be sure the electricity to the system you are working on is turned off; either the fuse removed or the circuit breaker set at off.
• Use of other manufacturers components will void warranty, listing and create a potential safety hazard.
• If you are unclear as to how to proceed, contact a qualified electrician.
• You don’t need special tools to install this fixture.
• Be sure to follow the steps in the order given.
• Read instructions carefully.
• Proper wiring is essential for the safe operation of this fixture.
• Save these instructions.
BEFORE YOU BEGIN
STEP 1:
Carefully remove the fixture from the carton and check that all parts are included, as shown in Figure 1 & 2. Be careful not to misplace any of the screws or parts which are needed to install this fixture.
INSTALLATION HC-893
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert fixture mounting screws (F) into threaded holes of universal mounting bar (E). Run screws all the way down to the heads.
STEP 2:
Place universal mounting bar (E) against outlet box (not supplied) and secure in place using outlet box screws (not supplied). Be sure the mounting screws (F) are PERFECTLY HORIZONTAL so fixture hangs straight.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (ROUND & SMOOTH) *PARALLEL WIRE (SQUARE & RIDGED)
* NOTE: When parallel wire is used, the tracer wire is square shaped or ridged, and the less tracer wire is round in shape or smooth. (Seen best when viewed from wire end.) To separate wires, grasp the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. Do Not twist wires together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector. If you can remove the wires, carefully re-do steps B and C, as above, and check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the outlet box in the same manner.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to be inserted into the hole with two raised dimples provided on the universal mounting bar (E). Wrap the ground wire from the fixture and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (G) on the universal mounting bar (E). If uninsulated ground wire is on the universal mounting bar (E), connect the ground wire from the fixture and the outlet box to it using a small wire connector (not supplied)
(See Figure 2).
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position canopy (D) over mounting screws (F) and secure in place with cap nuts (C).
STEP 2:
Install shade (A) and secure with retaining ring (B).
STEP 3:
Install lamps.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order replacement parts. Parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project