Sea gull lighting | 41035-962 | Installation guide | Sea Gull Lighting 41035-962 Installation Guide

HC-371
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
CLEANING
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
•
050698
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set
at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, consult a qualified
electrician.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Read instructions carefully.
Proper wiring is essential for the safe operation of this fixture.
Save these instructions.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place of
purchase. Be sure to use exact wording from illustration when
ordering parts.
BEFORE YOU BEGIN
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
GROUNDING & UNIVERSAL
MOUNTING BAR LOCK UP (FIG. 2)
GREEN
GROUNDING
SCREW (L)
*OUTLET BOX
*OUTLET BOX
SCREWS
UNIVERSAL
MOUNTING
PLATE (J)
GLASS
RETAINING
RING (C)
MOUNTING SCREWS (I)
*WIRE CONNECTOR
UNIVERSAL
MOUNTING
PLATE (J)
GLASS (B)
(FIG. 2)
*NOT SUPPLIED
CAP NUTS (N)
BACK PLATE (M)
(FIG. 1)
*NOT SUPPLIED
INSTALLATION
HC-371
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX.
STEP 1:
Insert fixture mounting screws (I) in threaded holes of universal
mounting bar (J). Run screws all the way down to the heads.
STEP 2:
Place universal mounting bar (J) against outlet box (not suppplied)
and screw in place using outlet box screws (not supplied). Be sure
the mounting screws are perfectly horizontal so fixture hangs
straight.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (L) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (J). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or
green insulated wire) around the green grounding screw (L) on the
universal mounting bar (J). If uninsulated ground wire is on the
universal mounting bar, connect the ground wire from the fixture (if
supplied) and the outlet box to it using a small wire connector (not
supplied) (See Figure 2). NOTE: Underwriters Laboratories (U.L.) does
not require all fixtures to have ground wires. These fixtures still meet
all U.L. specifications. The listing mark of underwriters on the
product identifies products manufactured under its listing and
Follow-Up Service Programs. NEVER CONNECT GROUND WIRE
TO BLACK OR WHITE POWER SUPPLY WIRES.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position backplate (M) over mounting screws (I) and secure in place
with cap nuts (N).
STEP 2:
Install glass (B). Secure in place with retaining ring (C ).
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
WHITE OR GREY WITH TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITHOUT
TRACER
BROWN, GOLD OR BLACK WITH TRACER
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. Do Not twist wires together before
using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above, and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 3:
Install lamp.
Download PDF