INSTALLATION AND SAFETY INSTRUCTIONS BEFORE YOU BEGIN IMPORTANT SAFETY INSTRUCTIONS • • • • • Be sure the electricity to the system you are working on is turned off; either the fuse removed or the circuit breaker set at off. Use of other manufacturers components will void warranty, listing and create a potential safety hazard. If you are unclear as to how to proceed, contact a qualified electrician. You don't need special tools to install this fixture. Be sure to follow the steps in the order given. Save these instructions. *OUTLET BOX UNIVERSAL MOUNTING BAR (D) GREEN GROUNDING SCREW (G) Carefully remove the fixture from the carton and check that all parts are included, as shown in figure 1 and 2. Be careful not to misplace any of the screws or parts which are needed to install this fixture. GROUND WIRE CAP NUTS (H) GLASS RETAINING SCREWS (C) SOCKET ASSEMBLY (B) SHADE (A) MOUNTING SCREWS (F) CANOPY (I) FIGURE 1 *NOT INCLUDED GROUNDING & UNIVERSAL MOUNTING BAR LOCK UP GREEN GROUNDING SCREW (G) *OUTLET BOX SCREWS MOUNTING SCREWS (F) GROUND WIRE Installation And Safety Instruction HC-1195 071107 *WIRE CONNECTOR UNIVERSAL MOUNTING BAR (D) FIGURE 2 Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill In Item Number On Carton And File This Sheet For Fixture Reference. ITEM#_________ INSTALLATION HC-1195 IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX. STEP 1: Insert mounting screws (F) in threaded holes of universal mounting bar (D). Run mounting screws (F) all the way down to heads. STEP 2: Using outlet box screws (not supplied) fasten universal mounting bar (D) to outlet box through slots in universal mounting bar (D). Be sure the mounting screws (F) are perfectly horizontal so fixture hangs straight. STEP 3: STEP 4: GROUNDING INSTRUCTIONS: The green grounding screw (G) is to be inserted into the hole with two raised dimples provided on the universal mounting bar (D). Wrap the ground wire from the fixture (if supplied) and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (G) on the universal mounting bar (D) if uninsulated wire is on the universal mounting bar (D), connect the ground wire from the fixture (if supplied) and the outlet box to it using a small wire connector (not supplied). NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. FINAL ASSEMBLY STEP 1: A. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below: Make sure no bare wires can be seen outside wire connectors. After wires are connected, tuck them carefully inside outlet box. Push the canopy (I) firmly over the mounting screws (F) and against the wall. Secure canopy (I) in place with cap nuts (H). STEP 2: Place shade (A) on socket assembly (B) and secure by threading glass retaining screws (C) into socket assembly (B). STEP 3: Install lamp. CLEANING GROUP A: CONNECT TO BLACK HOUSE WIRE BLACK *PARALLEL WIRE (ROUND & SMOOTH) *PARALLEL WIRE (SQUARE & RIDGED) GROUP B: CONNECT TO WHITE HOUSE WIRE WHITE *Note: When parallel wire is used, the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth. (Seen best when viewed from wire end.) To separate wires, grasp the ends of each wire and pull apart. B. Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. DO NOT twist wires together before using wire connectors. C. Fit a wire connector (not supplied) over the wires and thread the connector clockwise until you feel a firm resistance. D. Gently try to remove the wires from the connector. If you can remove the wires, carefully re-do steps B and C, as above and check again for a firm connection. E. Connect the fixture wire from group B to the white wire from the outlet box in the same manner. To clean, wipe fixture body with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper. ORDERING PARTS Keep this sheet for future reference, and in case you need to order replacement parts. Parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.