Sea gull lighting | 41120-820 | Installation guide | Sea Gull Lighting 41120-820 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
ASSEMBLY
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF .
GENERAL
STEP 1:
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
CANOPY (A)
RETAINING RING (P)
*WIRE CONNECTOR
GLASS (Z)
MOUNTING
SCREWS (I)
CAP NUT (N)
(FIG. 1)
*NOT SUPPLIED
GROUNDING & UNIVERSAL MOUNTING
BAR LOCK UP (FIG. 2)
*OUTLET BOX
GREEN
GROUNDING
SCREW (L)
*OUTLET BOX
SCREWS (K)
MOUNTING
SCREWS (I)
Installation And
Safety Instruction
HC-899
042905
*WIRE CONNECTOR
UNIVERSAL
MOUNTING
BAR (J)
*NOT SUPPLIED
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture.
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_______________
INSTALLATION
HC-899
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert fixture mounting screws (I) in threaded holes of universal
mounting bar (J). Run screws all the way down to the heads.
STEP 2:
Place universal mounting bar (J) against outlet box (not supplied)
and screw in place using outlet box screws (K) (not supplied). Be
sure the mounting screws are perfectly horizontal so fixture hangs
straight.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (L) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (J). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (L) on the universal
mounting bar (J). If uninsulated ground wire is on the universal
mounting bar, connect the ground wire from the fixture (if supplied)
and the outlet box to it using a small wire connector (not supplied)
(See Figure 2).
NOTE: Underwriters Laboratories does not require all fixtures to have
ground wires. These fixtures still meet all U.L. specifications.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position canopy (A) over mounting screws (I) and secure in place
with cap nuts (N).
STEP 2:
Install glass (Z) over the socket assembly and secure in place with
retaining ring (P).
STEP 3:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
*PARALLEL WIRE (ROUND & SMOOTH)
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
Install lamps.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF