advertisement
INSTALLATION INSTRUCTIONS
Rev. 02/09/2009
READ AND SAVE THESE INSTRUCTIONS
W
A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
MOUNTING THE FIXTURE (Fig. 1)
1. Shut off power at the circuit breaker and remove old fixture, including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Take care not to lose any small parts necessary for installation.
3. Attach the Circular Strap (B) using Junction Box
Screws (C) to the Outlet Box. The side of the
Circular Strap marked “GND” must face out.
4. Thread the two Studs (A) part way into Circular
Strap (B).
CONNECTING THE WIRES (Fig. 2)
5. At this point, connect the electrical wire as shown in Fig. 2, making sure that all wire connectors are secured. If your outlet has a ground wire (green or bare copper), connect the fixtures Ground Wire to it. Otherwise, connect the fixture Ground Wire directly to the circular strap using the Green
Screw provided. After wires are connected, tuck them carefully inside the Junction Box.
FINISHING THE INSTALLATION (Fig. 1)
6. Place Fixture Body (D) into the Studs (A) and secure it tightly using Cap Nut (E).
7. Place the Glass shades (F) over the Socket and tighten with Screw Shell (G).
8. Install the light bulb in accordance with the fixture’s specifications. (DO NOT EXCEED THE
MAXIMUM WATTAGE RATING!)
Your installation is now complete. Return power to the outlet box and test the fixture.
Fig. 1
Fig. 2
FIXTURE
WIRES
Black or
Smooth
HOUSE
WIRES
Black
(Hot)
E
FIXTURE
WIRES
White or
Ribbed
G
F
C
HOUSE
WIRES
White
(Neutral)
D
A
FIXTURE
WIRES
Bare
Copper
(Ground)
B
HOUSE
WIRES
Green
(Ground)
Note: Illustration (Fig. 1 ) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
In the event that you should have any installation question or are missing parts, please contact Customer Service. Customer service may be reached weekdays a 1-800-527-0998 between the hours of 8:00am and 5:00pm PST
(Pacific Standard Time).
LA-1299E/S
INSTRUCCIONES PARA LA INSTALACION
Rev. 02/09/2009
AGUARDE ESTAS INSTRUCCIONES
ADVERTENCIA! CORTE LA CORRIENTE DESDE EL FUSIBLE O EL INTERRUPTOR CENTRAL.
ENSAMBLAJE DE LA LAMPARA (Fig. 1)
1. Corte la corriente en el circuito principal y saque la lampara vieja incluyendo la barra transversal.
Fig. 1 coloque todas las partes en una superfice despejada.
Tenga cuidado de no perder las partes pequeñas que son necesarias para la instalacion.
G
F
Caja (C) de Union. El lado marcado “GND” deben quedar hacia afuera.
Abrazadera Circular (B).
CONECTANDO LOS ALAMBRES (Fig. 2)
5. Conecte el alambrado electrico como se muestra en la
(Fig.2), use un conector de plastico para asegurar la conexion. Si su caja de union tiene un alambre de tierra (verde o de cobre), conectelo al alambre de tierra de la lampara. Si no tiene, entonces conecte el alambre de tierra de la lampara directamente a la barra transversal usando el tornillo verde incluido.
Meta cuidadosamente las connexiones electricas dentro de la caja de union.
TERMINANDO LA INSTALACION (Fig.1)
6. Termine de colgar la lampara poniendo (D) el juego de luces sobre el nipple (A) asegure el juego de luces sobre la parred usando la Tuerca de Cabeza (E).
7. Coloque la Pantalla de Vidrio (F) sobre el socket y asegurelo con el rosca (G).
8. Instale el foco de acuerdo con las especificaciones de la lampara. (NO SE EXCEDA EL LOS WATTS
EXPECIFICADO!)
Su instalacion a terminado, conecte la corriente electrica y pruebe la lampara.
Nota: La ilustracion (Fig. 1) en este manual esta para el propositos de la instalacion solamente. Puede o no
puede ser identical al accesorio comprador.
Fig. 2
ALAMBRES
DE LA
LAMPARA
NEGRO O
SIN MARCA
ALAMBRES
DE LA
CASA
E
ALAMBRES
DE LA
LAMPARA
BLANCO O
CON MARCA
C
ALAMBRES
DE LA
CASA
BLANCO
(NEUTRAL )
D
A B
ALAMBRES
DE LA
LAMPARA
VERDE O DE
COBRE
(A TIERRA)
ALAMBRES
DE LA
CASA
En caso de preguntas sobre la instalacion o le faltaron partes, porfavor hablar al departamento de
Servicio al Cliente al 1-800-527-0998 de Lunes a
Viernes de 8:00 a.m. a 5:00 p.m. PST (Tiempo del
Pacifico).
LA-1299E/S
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project