Sea gull lighting | 41074-799 | Installation guide | Sea Gull Lighting 41074-799 Installation Guide

Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
FOR YOUR SAFETY
HC-445
110403
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED OR
THE CIRCUIT BREAKER OFF .
GENERAL
STEP 1:
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figures 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given.Read instructions carefully. If you are unclear
as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of this
fixture.
CANOPY (A)
*WIRE CONNECTOR
CANDLE COVER (Z)
BOBECHE (Y)
MOUNTING
SCREWS (I)
CAP NUTS (N)
(FIG. 1)
*NOT SUPPLIED
GROUNDING
GROUNDING WIRE
*OUTLET BOX
SCREWS (K)
*WIRE
CONNECTOR
FIXTURE
MOUNTING
SCREWS (I)
MOUNTING BAR
FLAT STRAP (B)
MOUNTING BAR
OFFSET STRAP (C)
GREEN
GROUNDING SCREW (G)
FIGURE 2
*NOT SUPPLIED
INSTALLATION
HC-445
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert fixture mounting screws (I) in threaded holes of universal
mounting bar (J). Run screws all the way down to the heads.
STEP 2:
Place universal mounting bar (J) against outlet box (not supplied)
and screw in place using outlet box screws (K) (not supplied). Be
sure the mounting screws are perfectly horizontal so fixture hangs
straight.
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (L) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (J). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (L) on the universal
mounting bar (J). If uninsulated ground wire is on the universal
mounting bar, connect the ground wire from the fixture (if supplied)
and the outlet box to it using a small wire connector (not supplied)
(See Figure 2).
NOTE: Underwriters Laboratories does not require all fixtures to have
ground wires. These fixtures still meet all U.L. specifications.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position canopy (A) over mounting screws (I) and secure in place
with cap nuts (N).
STEP 2:
Install bobeche (Y) (if applicable).
STEP 3:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
Install candle covers (Z) over the sockets (if applicable).
STEP 4:
Install lamps.
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
STEP 5:
Install shades (if applicable).
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF