Sea gull lighting | 41145-814 | Installation guide | Sea Gull Lighting 41145-814 Installation Guide

HC-1007
Installation And Safety Instructions
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
011507
FOR YOUR SAFETY
ASSEMBLY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF; EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER SET AT OFF.
Carefully remove the fixture from the carton and check that all parts
are included, as shown in figure 1 and 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
GENERAL
You don't need special tools to install this fixture. Be sure to follow
the steps in the order given. Read instructions carefully. If you are
unclear as to how to proceed, consult a qualified electrician.
CANOPY (O)
UNIVERSIAL
MOUNTING BAR (H)
GLASS
RETAINING
RING (M)
GLASS (J)
CAP NUTS (N)
HOLDER (K)
*WIRE CONNECTORS
FIGURE 1
*NOT INCLUDED
GROUNDING & UNIVERSAL MOUNTING
BAR LOCK UP (FIG. 2)
GREEN
GROUNDING
SCREW (L)
*OUTLET BOX
*OUTLET BOX
SCREWS
MOUNTING SCREWS (I)
*WIRE CONNECTOR
UNIVERSAL
MOUNTING
BAR (H)
(FIG. 2)
*NOT SUPPLIED
INSTALLATION
HC-1007
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert fixture mounting screws (I) in threaded holes of universal
mounting bar (H). Run screws all the way down to the heads.
STEP 2:
Place universal mounting bar (H) against outlet box (not suppplied)
and screw in place using outlet box screws (not supplied). Be sure
the mounting screws are perfectly horizontal so fixture hangs
straight.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (L) is
to be inserted into the hole with two raised dimples provided on the
mounting bar (H). Wrap the ground wire from the fixture (if supplied)
and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (L) on the
mounting bar (H) if uninsulated wire is on the mounting bar (H),
connect the ground wire from the fixture (if supplied) and the outlet
box to it using a small wire connector (not supplied).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products
manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
STEP 1:
Make sure no bare wires can be seen outside wire connectors.
STEP 2:
After wires are connected, tuck them carefully inside the outlet box.
Position canopy (O) over mounting screws (I) and secure in place
with cap nuts (N).
STEP 3:
Place glass (J) in holder (K) by screwing on retaining ring (M).
STEP 4:
GROUP A: CONNECT TO BLACK
HOUSE WIRE
GROUP B: CONNECT TO WHITE
HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
WHITE OR GREY WITH TRACER
BROWN, GOLD OR BLACK WITHOUT TRACER
WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK WITH TRACER
*Note: When parallel wire is used, the tracer wire is square shaped
or ridged and less tracer wire is round in shape or smooth.
(Seen best when viewed from wire end.) To separate wires, grasp
the ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw the
connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
Install lamps.
CLEANING
To clean, wipe fixture body with a soft cloth. Clean glass with a mild
soap. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
Download PDF