Sea gull lighting | 49151BLE-962 | Installation guide | Sea Gull Lighting 49151BLE-962 Installation Guide

INSTALLATION AND SAFETY INSTRUCTIONS
MOUNTING
SCREWS (I)
*OUTLET BOX
DIFFUSER (P)
*WIRE CONNECTORS
MOUNTING BAR (J)
BACKPLATE (F)
CAP NUTS (G)
*NOT SUPPLIED
FIGURE 1
GROUNDING & UNIVERSAL MOUNTING
BAR LOCK UP
GREEN
GROUNDING
SCREW (L)
MOUNTING
SCREWS (I)
*OUTLET BOX
UNIVERSIAL MOUNTING
BARS (J)
ASSEMBLY
STEP 1:
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1 & 2. Be careful not to misplace
any of the screws or parts which are needed to install this fixture.
*OUTLET BOX
SCREWS (K)
*WIRE CONNECTOR
FIGURE 2
*NOT SUPPLIED
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU
ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED
OR THE CIRCUIT BREAKER OFF .
GENERAL
You don’t need special tools to install this fixture. Be sure to follow the
steps in the order given. Read instructions carefully. If you are unclear
as to how to proceed, consult a qualified electrician.
NOTE: Proper wiring is essential for the safe operation of
this fixture.
Installation And
Safety Instruction
HC-940
112905
Line art shown may not exactly match the fixture enclosed.
However, the installation instructions do apply to this fixture
Fill In Item Number On Carton And
File This Sheet For Fixture Reference. ITEM#_______________
INSTALLATION
HC-940
IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET
BOX.
STEP 1:
Insert fixture mounting screws (I) into threaded holes of universal
mounting bar (J). Run screws all the way down to the heads.
STEP 2:
Place universal mounting bar (J) against outlet box (not supplied)
and screw in place using outlet box screws (K) (not supplied). Be
sure the mounting screws are PERFECTLY VERTICAL so fixture
hangs straight.
STEP 3:
A. Take note of the color of the wire(s) on your fixture. Identify
which group your fixture wire(s) falls into and connect the wires
according to the directions below:
STEP 4:
GROUNDING INSTRUCTIONS: The green grounding screw (L) is to
be inserted into the hole with two raised dimples provided on the
universal mounting bar (J). Wrap the ground wire from the fixture (if
supplied) and the ground wire from the outlet box (bare metal or green
insulated wire) around the green grounding screw (L) on the universal
mounting bar (J). If uninsulated ground wire is on the universal mounting bar, connect the ground wire from the fixture (if supplied) and the
outlet box to it using a small wire connector (not supplied) (See
Figure 2).
NOTE: Underwriters Laboratories (U.L.) does not require all fixtures to
have ground wires. These fixtures still meet all U.L. specifications. The
listing mark of Underwriters on the product identifies products
manufactured under its listing and Follow-Up Service Programs.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 1:
After wires are connected, tuck them carefully inside the outlet box.
Position backplate (F) over mounting screws (I) and secure in place
with cap nuts (G).
STEP 2:
Install lamps.
GROUP A: CONNECT TO BLACK
HOUSE WIRE
BLACK
GROUP B: CONNECT TO WHITE
HOUSE WIRE
WHITE
STEP 3:
Slide the edge of diffuser (P) into backplate lip (F), making sure it
fits securely.
CLEANING
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*NOTE: When parallel wire is used, the tracer wire is square shaped
or ridged, and the less tracer wire is round in shape or smooth. (Seen
best when viewed from wire end.) To separate wires, grasp the ends
of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly
against the black wire from the outlet box. Do Not twist wires
together before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and screw
the connector clockwise until you feel a firmness.
D. Try gently to pull the connector off the wires. If you can pull
the connector off, carefully re-do steps B and C, as above, and
check again for a firm connection.
E. Connect the fixture wire from group B to the white wire from
the outlet box in the same manner.
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. All parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
BALLAST REPLACEMENT
TURN POWER OFF.
Carefully remove glass by following the glass installation instructions
in reverse. Separate the 120v connection of the ballast from the
supply wire by removing wire nuts. Disconnect the secondary ballast
wires to the socket by inserting a small screwdriver into the rear of
the socket release the wire lead.
Remove ballast mounting screws and remove ballast from fixure
assembly. Replace ballast with the same model, secure ballast and
make proper wiring connections to the supply wire.
Download PDF