Quick Start Guide
1
Quick Start Guide
ULTRA CCTV
TIGON 1648
Digital Video Recorder
Open the CD DISC for
1. Complete user and installation manual.
2. Central Management Software.
3. Remote Viewing AP Software.
2
Power: Power On / Off switch
REC:
Recording
PLAY:
Playback
SEQ.:
Channel sequence
Split screen selection
0 ~ 9:
Channel select
Zoom:
Live zoom (2x)
FREEZE: Freezing live image
MENU:
Shortcut of frequently use functions
Setup:
Enter setup OSD menu
Spot:
Activate Call monitor. Quick Setup (Sequence ON/OFF, Fixed camera)
Frame by frame
reverse
Frame by frame
forward
Fast reverse
Stop playback
Direction button up/down/left/right
Enter button
PTZ: Enter to PTZ control mode
ESC: Exit menu
Alarm : Alarm output force control
Backup: Enter to backup mode
Fast forward
3
System rear connection detail
1) Video Source Connection
It connects video sources (camera image) to BNC connector via cable.
2) LOOP OUT Connection
BNC connector of LOOP OUT can be used as output to other device’s input.
Caution : It may cause low quality of picture when connecting disconnected cable from any device
to LOOP OUT BNC.
3) Monitor Connection
CVBS OUT/SPOT : It connects normal CCTV CRT monitor.
S-VHS : It connects monitor that supports S-VHS(S-VIDEO)
VGA : It connects PC monitor or LCD monitor (not supporting DVI)
4) Audio Connection
It connects audio source (mic) to audio
input of RCA and connects speaker to
audio output.
5) Network Connection
It supports 10/100 BaseT, connects
Cat5 cable with RJ-45
4
6) RS232 port Connection.
Reserve for technical support
7) USB port Connection
front
rear
Both USB port support USB devices such as USB mouse, USB external HDD and USB thumb
drive
8) ALARM IN (SENSOR) Connection
Remark : Max 6V/50mA
9) ALARM OUT Connection
* Alarm output 1~4CH
Support either NC or NO
Remark: Max24V/2A
5
10) Factory Reset Switch and NTSC/PAL system Switch
NTSC/PAL Shift Switch
Factory Reset Switch
Press the factory reset switch located at the left side of NTSC/PAL switch to return to factory
default setup values.
This reset switch should be pressed during power on. After OSD prompts "Factory reset
detected" message, then you can release the switch. The booting procedure would go on under
resetting setup values
Turn off the DVR before you do the NTSC/PAL system change.
Restart the DVR again after the system mode changed is done.
North America: NTSC
Europe: PAL
11) Power Connection and power switcher
6
Installation Guide for HDD & CD-RW/DVR-RW devices
You must set the hard drive Master and Slave jumper properly according to Hard drive
manufacturer's instructions to prevent system error and data loss.
Description
1. CD-RW/DVD-RW devices should be installed as “Primary Slave”.
2. First HDD for system needs to be installed as “Primary Master”.
MASTER : HDD#1
JR 1 : PRIMARY
SLAVE
: CD/DVD
MASTER : HDD#2
JR 2 : SECONDARY
SLAVE
: HDD#3
Guide Chart for installing several HDDs
CD-RW/ DVD-RW
Devices
HDD
Installed
HDD x 1
HDD
System
IDE
Connector
HDD#1
PRIMARY
MASTER
JR 1
SYSTEM
HDD#1
PRIMARY
MASTER
JR 1
SYSTEM
HDD#2
SECONDARY
MASTER
JR 2
HDD#1
PRIMARY
MASTER
JR 1
HDD#2
SECONDARY
MASTER
JR 2
HDD#3
SECONDARY
SLAVE
JR 2
IDE
Connector
PRIMARY
SLAVE
JR 1
HDD x 2
HDD x 3
SYSTEM
7
System On
• Put the power to the DVR.
• Turn on the power switch at the rear
• It takes about 100 seconds to boot (It may take more when network cable isn’t connected)
System Shutdown
1. Press Power button, the shutdown menu appears, select “OK” to shut down the system.
2. Or select [SETUP > SYSTEM > SYSTEM SHUTDOWN] to shutdown the system.
Remark: It takes around 30 seconds to complete the shutdown procedure.
8
on Screen
1
2
1
OSD :
<Screen Indication>
2
Top-Left
: Camera title
P – Pan/tilt (PTZ control)
A – Audio
Top-Right
: Record mode (Blue-Normal, Red-Event)
Motion status
Central
: Video Loss, Hidden Camera
Status Bar
: DVR status Indication
(Backup, HDD usage, Current Time, SEQUENCE, FREEZE, Login info. etc)
9
SETUP SCREEN
SYSTEM SETUP
INFORMATION: To show DVR information
DATE/TIME
: Setup date and time
DISK
: Show the HDD status and format HDD
USER
: User login ID and password setup
LOG
: System operation information
LOGOUT
: Logout system
SYSTEM SHUTDOWN: To shut down DVR
Remark: It takes more than 10 seconds to initialize (delete) the LOG information
10
NETWORK
NETWORK SETUP
LAN
: IP setup
DDNS : DDNS setup
E-MAIL: Setup E-mail address for event message
CALLBACK: Setup computer IP for event message
11
LAN
MAX CONNECTION
Up to 7 users
STATIC TYPE
For STATIC IP selection, settings for
IP, GATEWAY, NETMASK have to be
setup manually.
DHCP TYPE
For automatic DHCP IP selection, users only need
to set up the DNS data.
(DHCP operation mode must be structured under
IP sharing device)
ADSL TYPE
Please check your local ISP for the your ID
and password.
12
DEVICE
DEVICE SETUP
CAMERA : Camera setup
ALARM
DISPLAY:
: Alarm setup
On screen indication setup
MAIN MONITOR: Main monitor setup
SPOT MONITOR: Call monitor setup
MISCELLANEOUS: Key tone and keyboard
13
RECORD
RECORD SETUP
RECORD POLICY: HDD status setup when recording is full
RECORD
: Recording setup (resolution, recording status, alarm, motion etc)
14
RECORD POLICY
HDD status setup when recording is full
- Two types (Single Record, Overwrite)
RECORD
Recording setup for each camera
Remark:
Under half D1, the aspect ratio of local
AVI backup will be adjust to 8:3
RECORD MODE
Set up record type.
Default as OFF record mode.
NORMAL/EVENT RECORD FPS
Recording frame rate setup
NORMAL/EVENT RECORD QUALITY
Recording quality setup
SCHEDULE
Schedule recording setup
15
EVENT
EVENT SETUP
MOTION : Motion setup
SENSOR: NO/NC setup
VIDEO LOSS: Video loss detection setup
SYSTEM: Event action setup
16
SEARCH
3
1
2
1 Playback Screen : Video playback screen
2 Playback Time
: Playback Time Display
3 Display screen indication:
Playback Icon
Pause (Ⅱ)
Playback (▶)
Multiple Playback(▶ ▶, ▶ ▶ ▶, ▶ ▶ ▶ ▶)
17
SEARCH MENU
DISPLAY
Select screen division mode. (1,4,9,16 split screen)
CALENDAR SEARCH
Select date , hour, minutes, seconds in calendar search.
When you click MINUTE, you can find the specific record status under minute base
18
FIRST
Move to the beginning of the recorded data.
LAST
Move to the end of the recorded data.
BOOKMARK
When you set up a Bookmark time, this time will be
set as the starting time during back up.
PLAYBACK USER INERFACE
Playback buttons appears when locate the mouse pointer at the bottom of screen
SEARCH KEY
PLAY/PAUSE : Press PLAY to start from the position that was stopped from previous playback
Step backward / calendar search in
live mode
Fast backward / Beginning of
record time in live mode
Stop playback (Return to Live Display)
Step forward / Event search in live mode
Fast forward / Last record time in live mode
19
DEVICE
Search for internal record disks or external
Backup devices.
LOCAL DEVICE
Search the data of internal DISK.
BACKUP DEVICE
Search backup device (Select when you play the backup data.)
If there are various back up devices , you can select a specific one .
It only supports DVD +R/-R and CD RW discs for backup
If you can not play the AVI file from backup, please visit Xvid web site at http://www.xvid.org
to download the Xvid codec for installation.
20
BACKUP
Select backup data.
1) Backup Device Search
4) Warning when data size is over
2) Select data to backup
5) Transfer Image after pressing OK.
3) Calculate data size
6) Burning to CD
It would block remote search during local backup procedure.
21
REMOTE
1
4
3
5
6
7
10
8
9
2
<REMOTE PROGRAM IS?>
With connected to DVR remotely, it is to perform Remote Monitoring, Remote
Search, Remote Backup etc. (Please install remote program from the program
CD)
Environment conditions for Remote Program
1. INTEL P-4
2. 256M or higher main memory(512M recommend)
3. WINDOWS O/S(WIN 2000, XP, Vista(32bit))
4. 32MB VGA card supports RGB (ATI series recommend)
5. At least 10Mbps network speed (Max 100Mbps support)
Please note that some buttons and graphics may not be activated at this moment.
Those inactivated buttons will be used later when system upgrades and expands
If the viewer opens on IE, user needs to put connection IP on
Select Internet Options Æ Security Æ Trusted sites
ADD this website to the zone
22
1
Connection information
and Button
Shows DVR’s name, IP address and connection
status.
DVR connection button.
Add
: Enter IP address and user authentication
to connect DVR
Modify
: Modify IP address and user authentication
of the existing list
Delete
: Delete existing use.
<DVR Connection Window>
DVR name :
Specify a name that you can easily
identify.
Address :
Specify assigned IP address to
connect DVR (Type the Host name of
REAL IP or DDNS.)
<New Connection/Modify Dialogue Window>
23
Remote Search
1
4
12
5
6
10
7
8
9
2
3
1
11
Playback Display
Camera Name
Green Border Line :
Display the selected
camera.
Recorded
Date/Time
2
SECTION
Selects section
Section is created when Date/Time is changed to former time.
Former Date/Time will be kept in section 0.
Newly set Date/Time will be kept in section 1……
**Only one remote-playback connection is allowed
24
PLAYER
1
2
3
4
1
5
6
Search screen
Camera Name
Green border line :
Display the selected
camera.
Recorded
Time/Date
2
Starting/End
Move to starting record data
Play Progress Bar
Move to end of record data
25
CMS Main screen
1
7
2
3
4
1
5
6
Function button
1
1
2
3
4
5
6
7
8
9
User Management
Add, edit, delete of CMS account.
≫Add : add CMS user
≫Edit : revise user ID, PASSWORD
≫Delete:
: delete user
26
▣ CMS System Requirements
OS
CPU
Win 2000 / Win XP / Win Vista
INTEL P-4 2.4Ghz or over(recommendsP-4 3Ghz,over )
Main Memory
512MByte or over (recommends 1Gbyte,over)
Video Memory
64M over supports RGB (recommends 128Mbyte over)
Resolution
1024*768 over
Ethernet
10/100
Protocol
TCP/IP
Open the CD DISC for
1. Complete user and installation manual.
2. Central Management Software.
3. Remote Viewing AP Software.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising