Bulletin 284 ArmorStart Distributed Motor Control with Variable

Bulletin 284 ArmorStart Distributed Motor Control with Variable
[PROJECT NUMBER]
[DATE]
ROCKWELL AUTOMATION
[PROJECT NAME]
[PROJECT LOCATION]
PROCUREMENT SPECIFICATION
PROCUREMENT SPECIFICATION
Bulletin 284 ArmorStart
Distributed Motor Control with Variable Frequency Drive
NOTICE: The specification guidelines in this document are intended to aid in the specification of
products. Specific installations have specific requirements, and Rockwell Automation does not
recommend or intend any specific application based solely upon the guidelines provided here.
Because of the variety of uses for this information, the user of, and those responsible for applying
this information, are responsible for ensuring the acceptability of each application and appropriate
use of the guidelines. In no event will Rockwell Automation be liable for misuse, misapplication or
reliance on these guidelines in connection with any specific application. Rockwell Automation also
disclaims indirect or consequential damages resulting from the use or application of this
information.
Note: To download or view a .doc file version of this procurement specification, please visit:
www.rockwellautomation.com/industries/procurement-specifications
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
Rockwell Automation
1
[PROJECT NUMBER]
[DATE]
[PROJECT NAME]
[PROJECT LOCATION]
TABLE OF CONTENTS
PART 1 GENERAL ............................................................................................................................3 1.01 QUALIFICATIONS .............................................................................................................3 1.02 REFERENCES ...................................................................................................................3 1.03 ENVIRONMENTAL REQUIREMENTS ..............................................................................4 1.04 PRE-MANUFACTURE SUBMITTALS................................................................................4 1.05 FINAL SUBMITTALS..........................................................................................................4 PART 2 PRODUCTS .........................................................................................................................5 2.01 DESCRIPTION ...................................................................................................................5 2.02 RATINGS ...........................................................................................................................5 2.03 CONSTRUCTION ..............................................................................................................6 2.04 COMMUNICATIONS OPTIONS.........................................................................................8 2.05 CONFIGURATION .............................................................................................................8 2.06 FUNCTIONS ......................................................................................................................9 2.07 DETAILED SPECIFICATION ...........................................................................................10 2.08 DIMENSIONS AND WEIGHT...........................................................................................11 PART 3 EXECUTION ......................................................................................................................11 3.01 DELIVERY, STORAGE AND HANDLING ........................................................................11 3.02 INSTALLATION ................................................................................................................11 3.03 SPARE MATERIALS ........................................................................................................11 3.04 WARRANTY .....................................................................................................................12 Rockwell Automation
2
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
[PROJECT NUMBER]
[DATE]
[PROJECT NAME]
[PROJECT LOCATION]
SECTION XX XX XX
DISTRIBUTED MOTOR CONTROL WITH
VARIABLE FREQUENCY DRIVE
PART 1 GENERAL
1.01 QUALIFICATIONS
A. Manufacturer
1.
2.
The manufacturer shall have a minimum of 25 years of experience in the
manufacture of distributed motor control.
The approved manufacturers are:
a)
b)
Rockwell Automation Allen-Bradley
Substitutions: None permitted
B. Support
1.
2.
3.
4.
The manufacturer shall maintain factory trained and authorized service facilities
within 100 miles of the project and shall have a demonstrated record of service for at
least the previous ten years.
Support personnel are to be direct employees of the manufacturer and be available
24 hours per day through a toll-free number.
The manufacturer shall provide all required start-up and training services.
The approved manufacturers are:
a)
b)
Rockwell Automation Customer Support & Maintenance
Substitutions: None permitted
C. Certification
1.
2.
To ensure all quality and corrective action procedures are documented and
implemented, all manufacturing locations shall be certified to the ISO-9001 Series of
Quality Standards.
Third-party manufacturers and brand labeling shall not be allowed.
1.02 REFERENCES
A. The distributed motor control shall be designed to meet or exceed the applicable
requirements to comply with the standards:
1.
UL/CSA
a)
b)
UL 508C
CSA C22.2, No. 14
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
Rockwell Automation
3
[PROJECT NUMBER]
[DATE]
2.
EN/IEC
a)
b)
c)
d)
3.
4.
[PROJECT NAME]
[PROJECT LOCATION]
EN 50178
EN 61800-3
EN/IEC 60947-4-2
CE Marked per Low Voltage Directive 2006/95/EC and EMC Directive
2004/108/EC
CCC
ODVA for EtherNet/IP and DeviceNet
B. The distributed motor control shall be certified cULus (File No. E207834, Guides NMMS,
NMMS7).
1.03 ENVIRONMENTAL REQUIREMENTS
A. The supplier shall confirm specified service conditions during and after installation of
products.
B. The supplier shall maintain the area free of dirt and dust during and after installation of
products.
1.04 PRE-MANUFACTURE SUBMITTALS
A. Refer to Section _________ for submittal procedures.
B. Product Data
1.
2.
Publications on distributed motor control.
Data sheets on all furnished options.
C. Specification Response
1.
2.
Detailed response to this specification showing where in the literature each
requirement is satisfied.
Clearly identified clarifications and exceptions.
D. Installation Instructions
1.
A copy of the manufacturer’s installation instructions, including receiving, handling
and storage instructions.
E. Testing and Test Reports
1.
2.
Testing per manufacturer’s standard.
A copy of the test reports, if available, shall be provided as part of the final
documentation.
1.05 FINAL SUBMITTALS
A. Refer to Section ________ for procedure on submittal of final documentation.
B. Supplier Certification
1.
The supplier shall provide certification that the distributed motor control has been
installed in accordance with the manufacturer’s instructions.
Rockwell Automation
4
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
[PROJECT NUMBER]
[DATE]
2.
[PROJECT NAME]
[PROJECT LOCATION]
The supplier shall provide certification that the distributed motor control settings
have been properly adjusted.
C. Final Drawings
1.
2.
3.
4.
The manufacturer shall provide final drawings reflecting the “As-Shipped” state of
the installed equipment.
Manufacturer drawings shall be provided in DWG format.
Manufacturer drawings do not need to be stamped if a drawing schedule is provided
that lists the drawing numbers, revision levels, and status of drawings (Preliminary,
Approval, Final, etc.).
The supplier shall be responsible for making any changes to the “As-Shipped”
drawings from the manufacturer to reflect any field modifications.
D. Maintenance Data
1.
2.
3.
4.
Distributed motor control installation instructions and User Manual.
Parameter listing with final settings.
Field service report from start-up service.
Name and phone number for a local distributor for the spare parts.
PART 2 PRODUCTS
2.01 DESCRIPTION
A. Allen-Bradley – Bulletin 284 ArmorStart Distributed Motor Control with Variable
Frequency Drive (No substitutions)
2.02 RATINGS
A. The distributed motor control (DMC) shall support a three-phase induction motor. DMC
power circuit ratings:
1.
Horsepower of:
a)
b)
2.
Operating voltage of:
a)
b)
3.
up to 2.0 HP (1.5 kW) at 240 VAC.
up to 5 HP (3.0 kW) at 480 VAC.
200 to 240 VAC (DeviceNet versions only), or
380 to 480 VAC.
Operating frequency of 50/60 Hz.
B. The DMC shall accept control power of:
1.
2.
3.
24 VDC (+10%, -15%) A2,
120 VAC (+10%, -15%) A2 (DeviceNet versions only), or
240 VAC (+10%, -15%) A2 (DeviceNet versions only).
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
Rockwell Automation
5
[PROJECT NUMBER]
[DATE]
[PROJECT NAME]
[PROJECT LOCATION]
C. The DMC shall be equipped with a Short Circuit Protection Device (SCPD), Performance
Type 1. The DMC shall have an Irms of:
1.
2.
30, 45 or 65 kA @ 480Y/277 VAC.
30 or 65 kA @ 480 VAC.
D. The DMC shall be UL Listed for Group Motor Applications, sized per NFPA 70 (NEC) or
NFPA 79.
E. The DMC’s environmental ratings include:
1.
2.
3.
4.
5.
6.
7.
Enclosure rating of Type 4/12 and IP67.
Operating temperature range of -20 to +40°C (-4 to +104°F).
Relative humidity range of 0 to 95%, non-condensing.
Operating shock resistance to 15 G.
Operating vibration resistance to 1 G, 0.15 mm (0.006 in.) displacement.
Ability to operate without de-rating to an elevation of 1000 m.
Application in Pollution Degree 3 environments.
2.03 CONSTRUCTION
A. The distributed motor control (DMC) shall be a modular plug-n-play design and shall offer
variable speed control of a three-phase AC squirrel cage induction motor.
B. The DMC’s version shall be:
1.
2.
EtherNet/IP, or
DeviceNet.
C. The DMC’s drive performance shall be:
1.
DeviceNet versions only: Sensorless Vector Performance (SVP) (Volts-per-Hertz) —
The DMC shall provide:
a)
b)
c)
2.
Auto boost (IR compensation) and slip compensation
Excellent speed regulation, even as load increases
High levels of torque across the entire speed range of the drive
EtherNet/IP and DeviceNet versions: Sensorless Vector Control (SVC) — The DMC
shall provide:
a)
b)
c)
Exceptional speed regulation
Very high levels of torque across the entire speed range of the drive
Adaptation to individual motor characteristics
D. The DMC shall provide a local at-motor disconnect means by incorporating a motor
circuit protector.
E. The DMC shall use quick disconnects for I/O and communications.
F. 3-phase power, control power and motor connections shall be made via a gland plate:
1.
Conduit/cord-ready power options with 3/4 and 1 in. conduit holes:
a)
b)
Rockwell Automation
6
Trunk and drop
Daisy chain
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
[PROJECT NUMBER]
[DATE]
2.
[PROJECT NAME]
[PROJECT LOCATION]
ArmorConnect media option. The media shall be:
a)
b)
produced by the DMC manufacturer, or
UL 2237 and approved for use by the DMC manufacturer.
G. On SVC versions (option), the DMC shall provide an internal EMI filter and shall be CE
compliant.
H. The DMC shall include a source brake contactor (option), an internal contactor used to
switch the electromechanical motor brake on/off (motor brake is powered from the main
power circuit).
I. The DMC shall be configurable with a dynamic brake connector for the motor brake
(option). A dynamic brake resistor (option) with plug-n-play design shall be available.
J. DeviceNet and ArmorPoint versions (option): the DMC shall include a control brake
contactor, an internal contactor used to switch the electromechanical motor brake on/off
(motor brake is powered from the control voltage circuit).
K. The DMC shall be supplied with a 3-meter unshielded 4-conductor cordset. If the DMC
includes the EMI filter option, it shall be supplied with a shielded cordset.
L. The DMC shall include a local fault reset button and 4 status LEDs:
1.
2.
3.
4.
Power
Run
Network
Fault
M. The DMC shall also include externally accessible:
1.
2.
EtherNet/IP versions: 2 solid-state output connections (Micro/M12) with status
indication, 4 configurable 24 VDC inputs (Micro/M12) with status indication, IP
address switches, embedded dual port Ethernet switch with 4 status indicators and
a ground terminal.
DeviceNet versions: 2 relay output connections (Micro/M12) with status indication, 4
configurable 24 VDC inputs (Micro/M12) with status indication, DeviceNet
connection (Mini/M18) and a ground terminal.
N. The DMC shall have local control (option) with field-disable capability (except OFF):
HAND – OFF – AUTO – JOG – FORWARD/REVERSE keypad.
O. I/O points shall be used with sensors and actuators.
1.
2.
3.
Two 24 VDC nominal outputs – 0.5 A per point (max 1 A total outputs).
Four 24 VDC nominal inputs – 50 mA per point (200 mA total inputs).
DeviceNet versions (option): 0 to 10V analog input.
P. The DMC shall include an output contactor (option), sourced from control voltage to
isolate the load side of the DMC.
Q. DeviceNet versions (option): The DMC shall include a safety monitor option which allows
independent monitoring of the output status of the device.
1.
2.
The function shall be implemented using a normally closed contact, complying with
IEC 60947-5-1.
Two terminal blocks shall be provided as the inputs that may be used with an
external safety circuit which monitors the status of the isolation contactor.
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
Rockwell Automation
7
[PROJECT NUMBER]
[DATE]
[PROJECT NAME]
[PROJECT LOCATION]
2.04 COMMUNICATIONS OPTIONS
A. EtherNet/IP versions:
1.
2.
3.
EtherNet/IP versions of the distributed motor control (DMC) shall allow the
integration of I/O control, device configuration and data collection across multiple
networks, enabling internet connectivity.
The EtherNet/IP DMC shall include a dual port 10/100mb/s embedded Ethernet
switch that supports linear or device level ring (DLR) topology.
EtherNet/IP addressing shall be by:
a)
b)
c)
4.
5.
6.
Auto addressing via DHCP utility
Local node switch
Static IP address
The EtherNet/IP DMC shall include an embedded web server.
The EtherNet/IP DMC shall support the IEEE 1588 transparent clock.
The EtherNet/IP DMC shall support DeviceLogix, which allows local control using
simple embedded logic.
B. DeviceNet versions:
1.
2.
DeviceNet versions of the distributed motor control (DMC) shall allow efficient data
handling on the device-level DeviceNet network.
DeviceNet addressing shall be by:
a)
b)
3.
4.
Hard set node address switches
Software node addressing
The DeviceNet DMC shall support DeviceLogix, which allows local control using
simple embedded logic.
The DeviceNet DMC shall provide peer-to-peer zone interlocking parameters (ZIP)
to allow direct communication with up to 4 other DeviceNet nodes.
2.05 CONFIGURATION
A. The distributed motor control (DMC) shall have the capability to be programmed by:
1.
2.
3.
Add-On Profile (AOP) for CompactLogix and ControlLogix Controllers – The AOP is
used for the Logix Designer programming tool in Studio 5000 software, which is a
single control platform. The AOP simplifies setup and commissioning via predefined
tags and commissioning wizards and allows automatic tag generation and copy and
paste functionality for quick setup and configuration of multiple DMCs. The Logix
Designer programming tool is also used by the DMC’s DeviceLogix program to
perform configuration locally.
RSNetWorx™ – For the DeviceNet version, the device configuration tool
RSNetWorx can configure the DMC, using the embedded electronic data sheet
(EDS).
Internal Webpage – For the EtherNet/IP version, the DMC’s web interface can be
used to configure the DMC when the AOP is not available.
Rockwell Automation
8
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
[PROJECT NUMBER]
[DATE]
[PROJECT NAME]
[PROJECT LOCATION]
B. EtherNet/IP versions:
1.
2.
The EtherNet/IP DMC’s web interface can be used to configure the DMC when AOP
is not available.
The EtherNet/IP DMC’s embedded web server shall also be able to be configured
for:
a)
b)
c)
d)
e)
Login and password protection.
Sending an e-mail when a fault or warning occurs. E-mail supports Simple Mail
Transfer Protocol (SMTP).
Uploading EDS files.
Status and diagnostics read/write.
Administrative tasks.
2.06 FUNCTIONS
A. Motor control shall be of a three-phase AC squirrel cage induction motor.
1.
2.
up to 2.0 HP (1.5 kW) at 240 VAC, or
up to 5 HP (3.0 kW) at 480 VAC.
B. Electronic motor overload protection shall be accomplished with an I2t algorithm.
1.
2.
3.
Solid-state overload: 150% for 60 seconds or 200% for 3 seconds.
Class 10 protection with speed sensitive response and power-down overload
retention function.
Overcurrent protection: 200% hardware limit, 300% instantaneous fault.
C. Fault diagnostics shall include:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Short Circuit
Overload
Phase Short
Ground Fault
Stall
Control Power Loss
I/O Fault
Over Temperature
Over Current
EEprom Fault
Hardware Fault
D. Device status parameters shall include:
1.
2.
3.
4.
5.
6.
7.
8.
Hdw Inputs
Network Inputs / DeviceIn Data
Network Outputs / DeviceOut Data
Trip Status
Starter Status
InternalLinkStat / DNet Status
Starter Command
Breaker Type
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
Rockwell Automation
9
[PROJECT NUMBER]
[DATE]
9.
10.
11.
12.
13.
14.
15.
[PROJECT NAME]
[PROJECT LOCATION]
Last Pr Fault
Warning Status
Output Frequency
Command Frequency
Output Current
Output Voltage
DC Bus Voltage
E. Basic configuration parameters shall include:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Motor NP Volts
Motor NP Hertz
Motor OL Current
Minimum Frequency
Maximum Frequency
Stop Mode
Speed Reference
Accel Time 1
Decel Time 1
2.07 DETAILED SPECIFICATION
A. All versions, power circuit:
1.
2.
3.
4.
Rated Impulsed Voltage (Uimp): 6 kV
Dielectric Withstand: UL – 2200 VAC, IEC – 2500 VAC
Reset Mode: Automatic or manual
Utilization Category: AC-3
B. EtherNet/IP versions:
1.
2.
3.
4.
Ethernet Communication Rate: 10/100 Mbps, auto-negotiate half- and full-duplex
Ethernet Ports: 2 (embedded switch)
Device Level Ring Support: Beacon Performance, IEEE 1588 Transparent Clock
Data:
a)
b)
c)
5.
Connection support:
a)
b)
6.
7.
8.
9.
Transported over both TCP and UDP
Minimum of 500 I/O packets per second
Supports up to 150 concurrent TCP sockets
Scheduled (Class 1)
Unscheduled (Class 3 and UCMM)
Maximum Concurrent Explicit Messages (CIP Class 3): 6
Class 1 Connection API: 2 to 3200 ms
Class 3 Connection API: 100 to 10,000 ms
Request Packet Interval (RPI): 20 ms default
Rockwell Automation
10
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
[PROJECT NUMBER]
[DATE]
[PROJECT NAME]
[PROJECT LOCATION]
C. DeviceNet versions:
1.
2.
DeviceNet Supply Voltage Rating Range: 11 to 25 VDC, 24 VDC nominal
DeviceNet Input Current:
a)
b)
3.
4.
5.
167 mA @ 24 VDC – 4.0 W
364 mA @ 11 VDC – 4.0 W
DeviceNet Input Current Surge: 15 A for 250 s
Baud Rates: 125, 250, 500 kbps
Distance Maximum:
a)
b)
c)
500 m (1630 ft) @ 125 kbps
200 m (656 ft) @ 250 kbps
100 m (328 ft) @ 500 kbps
2.08 DIMENSIONS AND WEIGHT
A. The dimensions of the distributed motor control (DMC) shall not exceed 287.5 mm
(11.32 in.) height x 444.38 mm (17.50 in.) width [or 420.38 mm (16.55 in.) width] x
266.9 mm (10.51 in.) depth with motor connection cable.
B. The approximate weight of the DMC shall be 13.6 kg (30 lb).
PART 3 EXECUTION
3.01 DELIVERY, STORAGE AND HANDLING
A. The supplier shall coordinate the shipping of equipment.
B. The supplier shall store the equipment in a clean and dry space.
C. The supplier shall protect the units from dirt, water, construction debris and traffic.
3.02 INSTALLATION
A. The supplier shall verify all distributed motor control components have been installed not
exceeding the specifications or with proper derating prior to energizing.
B. The supplier shall follow local code and regulations with regard to electrical installation.
C. The supplier shall provide reasonable protection against accidental damage to
component and associated cables.
D. The supplier shall ensure accessibility to diagnostic lights, communication ports and
connection. These components shall be free from obstruction at all times.
E. The supplier shall verify all distributed motor control settings have been properly adjusted
prior to energizing.
3.03 SPARE MATERIALS
A. The supplier shall provide one (1) spare distributed motor control of each size utilized,
including options.
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
Rockwell Automation
11
[PROJECT NUMBER]
[DATE]
[PROJECT NAME]
[PROJECT LOCATION]
3.04 WARRANTY
A. The manufacturer shall provide their standard parts warranty for eighteen (18) months
from the date of shipment or twelve (12) months from the date of being energized,
whichever occurs first.
B. The manufacturer shall confirm this warranty as part of the submittal.
END OF SECTION
Rockwell Automation, Rockwell Software, Allen-Bradley, ArmorConnect, ArmorStart, DeviceLogix, RSNetWorx and Studio 5000 are
trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Automation
12
Bulletin 284 ArmorStart DMC
284-SR001A-EN-P
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement