advertisement
Acer Projector
X115/ X115H/ X125H/ X135WH/
H6517ABD/ D602/ D602D/
D612D/ D622D/E145F/ EV-S62/
EV-S62H/EV-X62H/ EV-W62H/ HE-
801K/ V31S/ V32S/ V32X/ V32W/
AS304/ AS314/ AX314/ AW314/
D600+/ D600D+/ D610D+/
D620D+/ X114PH/ X124PH/
X134PWH Series
User's Guide
Copyright © 2016. Acer Incorporated.
All Rights Reserved.
Acer Projector User's Guide
Original Issue: 03/2016
Changes may be made periodically to the information in this publication without obligation to notify any person of such revisions or changes. Such changes will be incorporated in new editions of this manual or supplementary documents and publications. This company makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims the implied warranties of merchantability or fitness for a particular purpose.
Record the model number, serial number, purchase date and place of purchase information in the space provided below. The serial number and model number are recorded on the label affixed to your projector. All correspondence concerning your unit should include the serial number, model number and purchase information.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronically, mechanically, by photocopy, recording or otherwise, without the prior written permission of Acer Incorporated.
Model number: _________________________________
Serial number: __________________________________
Date of purchase: _______________________________
Place of purchase: ______________________________
"HDMI™, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."
Information for your safety and comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to the external power supply unit:
•
Install the power supply unit before connecting the power cord to the AC power outlet.
•
Unplug the power cord before removing the power supply unit from the projector.
•
If the system has multiple sources of power, disconnect power from the system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible and located as close to the equipment operator as possible. When you need to disconnect power to the equipment, be sure to unplug the power cord from the electrical outlet.
iii
Warnings!
•
Do not use this product near water.
•
Do not place this product on an unstable cart, stand or table. If the product falls, it could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable operation of the product and to protect it from overheating. These openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind onto or into the product.
iv
•
To avoid damage of internal components and to prevent battery leakage, do not place the product on a vibrating surface.
•
Never use it under sporting, exercising, or any vibrating environment which will probably cause unexpected short current or damage rotor devices, lamp.
Using electrical power
•
This product should be operated from the type of power indicated on the marking label. If you are not sure of the type of power available, consult your dealer or local power company.
•
Do not allow anything to rest on the power cord. Do not locate this product where people will walk on the cord.
•
If an extension cord is used with this product, make sure that the total ampere rating of the equipment plugged into the extension cord does not exceed the extension cord ampere rating. Also, make sure that the total rating of all products plugged into the wall outlet does not exceed the fuse rating.
•
Do not overload a power outlet, strip or receptacle by plugging in too many devices. The overall system load must not exceed 80% of the branch circuit rating. If power strips are used, the load should not exceed 80% of the power strip's input rating.
•
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet is properly grounded before inserting the AC adapter plug. Do not insert the plug into a non-grounded power outlet. Contact your electrician for details.
Warning! The grounding pin is a safety feature. Using a power outlet that is not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected noise produced by other nearby electrical devices that may interfere with the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need to replace the power cord set, make sure that the new power cord meets the following requirements: detachable type, UL listed/CSA certified, VDE approved or its equivalent, 4.5 meters (15 feet) maximum length.
Product servicing
Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltage points or other risks. Refer all servicing to qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service personnel when:
•
the power cord or plug is damaged, cut or frayed
•
liquid was spilled into the product
•
the product was exposed to rain or water
•
the product has been dropped or the case has been damaged
•
the product exhibits a distinct change in performance, indicating a need for service
•
the product does not operate normally after following the operating instructions
v
Note: Adjust only those controls that are covered by the operating instructions, since improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
Additional safety information
•
Do not look into the projector's lens when the lamp is on. The bright may hurt your eyes.
•
Turn on the projector first and then signal sources
•
Do not place the product in following environments:
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate optical components, shortening the life span and darkening the image.
•
•
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
• Locations where the altitudes are higher than 10000 feet.
•
Unplug immediately if there is something wrong with your projector. Do not operate if smoke, strange noise or odor comes out of your projector. It
vi
might cause fire or electric shock. In this case, unplug immediately and contact your dealer.
•
Do not keep using this product to break or drop it. In this case contact your dealer for inspection.
•
Do not face the projector lens to the sun. It can lead to fire.
•
When switching the projector off, suggest to ensure the projector completes its cooling cycle before disconnecting power.
•
Do not frequently turn off the main power abruptly or unplug the projector during operation. The best way is to wait for the fan to turn off before turning main power off.
•
Do not touch air outlet grille and bottom plate which becomes hot.
•
Clean the air filter frequently if have. The temperature inside may rise and cause damage when the filter/ventilation slots clogged with dirt or dust.
•
Do not look into the air outlet grille when projector is operating. It may hurt your eyes.
•
Always open the lens shutter or remove the lens cap when the projector is on.
•
Do not block the projector lens with any object when the projector is under operation as this could cause the object to become heated and deformed or even cause a fire. To temporarily turn off the lamp, press HIDE on the remote control.
•
The lamp becomes extremely hot during operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement.
•
Do not operate lamps beyond the rated lamp life. It could cause it to break on rare occasions.
•
Never replace the lamp assembly or any electronic components unless the projector is unplugged.
•
The product will detect the life of the lamp itself. Please be sure to change the lamp when is showing warning message.
•
When changing the lamp, please allow unit to cool down, and follow all changing instructions.
•
Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
•
Do not attempt to disassemble this projector. There are dangerous high voltages inside which may hurt you. The only user serviceable part is the lamp which has its own removable cover. Refer servicing only to suitable qualified professional service personnel.
•
Do not stand the projector on end vertically. It may cause the projector to fall over, causing injury or damage.
•
This product is capable of displaying inverted images for ceiling mount installation. Only use acer ceiling mount kit for mounting the projector and ensure it is securely installed.
vii
Caution for Listening
To protect your hearing, follow these instructions.
•
Increase the volume gradually until you can hear clearly and comfortably.
•
Do not increase the volume level after your ears have adjusted.
•
Do not listen to music at high volumes for extended periods.
•
Do not increase the volume to block out noisy surroundings.
•
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize pollution and ensure utmost protection of the global environment, please recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit http://www.acer-group.com/public/Sustainability/sustainability01.htm
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
“Lamp(s) contain Mercury,
Dispose Properly.”
Lamp(s) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws. For more information, contact the
Electronic Industries Alliance at www.eiae.org. For lamp-specific disposal information, check www.lamprecycle.org
viii
First things first
Usage Notes
Do:
•
Turn off the product before cleaning.
•
Use a soft cloth moistened with mild detergent to clean the display housing.
•
Disconnect the power plug from AC outlet if the product is not being used for a long period of time.
Don't:
•
Block the slots and openings on the unit provided for ventilation.
•
Use abrasive cleaners, waxes or solvents to clean the unit.
•
Use under the following conditions:
•
In extremely hot, cold or humid environments.
•
In areas susceptible to excessive dust and dirt.
•
Near any appliance that generates a strong magnetic field.
•
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this user's guide to maximize the life of your unit.
Warning:
•
Do not look into the projector's lens when the lamp is on. The bright light may hurt your eyes.
•
To reduce the risk of fire or electric shock, do not expose this product to rain or moisture.
•
Please do not open or disassemble the product as this may cause electric shock.
•
When changing the lamp, please allow unit to cool down, and follow all changing instructions.
•
This product will detect the life of the lamp itself. Please be sure to change the lamp when it shows warning messages.
•
Reset the "Lamp Hour Reset" function from the Onscreen display "Management" menu after replacing the lamp module.
•
When switching the projector off, please ensure the projector completes its cooling cycle before disconnecting power.
•
Turn on the projector first and then the signal sources.
•
Do not use lens cap when projector is in operation.
•
When the lamp reaches the end of its life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn back on until the lamp module has been replaced. To replace the lamp, follow the procedures listed under
Information for your safety and comfort iii
First things first
Usage Notes
Precautions
Introduction
Product Features
Package Overview
Projector Overview
Projector Outlook
Control Panel
Remote Control Layout
Getting Started 8
Connecting the Projector
Turning the Projector On/Off
Turning on the Projector
Turning the projector off
8
10
10
11
Adjusting the Projected Image
Adjusting the Height of Projected Image
12
12
How to optimize image size and distance 13
How to get a preferred image size by adjusting distance and zoom 16
viii viii viii
1
1
2
5
6
3
3
User Controls
Installation menu
Onscreen Display (OSD) Menus
Color
Image
Setting
Management
Audio
3D
Language
Appendices
Troubleshooting
19
19
27
27
28
28
20
21
23
25
29
29
LED & Alarm Definition Listing
Cleaning and replacing the dust filters
Replacing the Lamp
Ceiling Mount Installation
Specifications
Compatibility modes
Regulations and safety notices
36
39
42
33
34
35
47
Introduction
Product Features
This product is a single-chip DLP
®
projector. Outstanding features include:
•
DLP
®
technology
•
X115/D602/EV-S62/V31S/AS304/D600+/X115H/D602D/EV-S62H/V32S/AS314/
D600D+/X114PH series: Native 800 x 600 SVGA resolution
X125H/D612D/EV-X62H/V32X/AX314/D610D+/X124PH series: Native 1024 x
768 XGA resolution
X135WH/D622D/EV-W62H/V32W/AW314/D620D+/X134PWH series: Native
1280 x 800 WXGA resolution
H6517ABD/E145F/HE-801K series: 1920x1080 1080p resolution
Full/4:3/16:9/L.Box aspect ratio supported
•
Enables projecting 3D content via DLP Link Technology: Blue-Ray 3D supported and nVidia 3DTV Play Ready
•
Acer ColorBoost technology delivers nature’s true colors for vivid, life-like images
•
High brightness and contrast ratio
•
Versatile display modes (Bright, Presentation, Standard, Video, Game,
Education, Movie, Dark Cinema, Sports, User) enable optimum performance in any situation
•
NTSC / PAL / SECAM compatible and HDTV (480i/p, 576i/p, 720p, 1080i/p) supported
•
Lower power consumption and economy (ECO) mode extends lamp life
•
Acer EcoProjeciton Technology delivers Intelligent power management approach and physical efficiency improvement
•
Advanced digital keystone correction optimizes presentations
•
Smart detection delivers quick, intelligent source detection
•
Multi-language onscreen display (OSD) menus
•
Manual focus projection lens zooms up to 1.1x
•
2x digital zoom
•
Microsoft
®
Windows
®
2000, XP, Vista
®
, Windows 7, Windows 8, Windows
10, Macintosh
®
OS compliant
®
1
Note: Functions vary depending on model definition.
2
Package Overview
This projector comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if any thing is missing.
Projector Power cord VGA cable
Remote control 2 x Batteries
(option)
Security card
User’s guide Quick start guide Carrying case
(option)
Dust filters
(option)
HDMI cable
(option)
Projector Overview
Projector Outlook
Front / upper side
1
2
3 4 5 6
#
1 Air outlet
2 Lamp cover
3 Control panel
4 Power button
5 Zoom lever
6 Focus ring
Description
7
8
9
10
11
# Description
7 Air inlet
8 Remote control receiver
9 Projection lens
10 Lens cap
11 Tilt adjusting wheels
3
4
Right / Rear side
<Right side>
1 2 3
<Rear side>
4 5 6 7 8
5
1
2
3
4
5
# Description
RS232 connector
PC analog signal/HDTV/component video input connector
HDMI connector
Security bar
Audio input connector
2
2
3
6
9
6
10
6
# Description
Mini USB Ctrl connector (for firmware upgrade and page up/page down function)
7
Power socket
8
Kensington
TM
lock port
9 S-Video input connector
10 Composite video input connector
Note: Functions vary depending on model definition.
5
Control Panel
1 8 2 3
4
9
5
6
10
7
2
3
# Icon
1 POWER POWER
Function
LAMP
TEMP
LAMP
TEMP
4 RESYNC RESYNC
5 SOURCE SOURCE
6
7
8
9
10
POWER
MODE MODE
MENU MENU
Description
Power Indicator LED
Lamp Indicator LED
Temp Indicator LED
Automatically synchronizes the projector to the input source.
Changes the active source.
See the contents in "Turning the Projector
Press "MODE" to select the display mode from Bright, Presentation, Standard, Video,
Game, Education and User.
•
Press "MENU" to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu.
•
Confirm your selection of items.
Four directional select keys
Use to select items or make adjustments to your selection.
Keystone
Adjusts the image to compensate for distortion caused by tilting the projector.
Note: Functions vary depending on model definition.
6
Remote Control Layout
9
11
2
5
7
13
MEDIA
SETUP
ZOOM
MODE
RATIO
SOURCE
HIDE
FREEZE
1
3
4
6
8
10
12
Model No:E-26281
15
17
19
21
23
14
16
18
20
22
24
8
9
10
3
4
1
# Icon Function
Infrared transmitter
2 POWER
5
6
7
11
12
Description
Sends signals to the projector.
Refer to the "Turning the Projector On/Off" section.
SOURCE
MODE
HIDE
MEDIA
SETUP
3D
SOURCE
MODE
HIDE
Press "3D" to select 3D models.
Changes the active source.
Press "MODE" to select the display mode from Bright,
Presentation, Standard, Video, Game, Education, Movie, Dark
Cinema, Sports and User.
Momentarily turns off the video. Press "HIDE" to hide the image, press again to display the image.
MEDIA_SETUP No function.
RATIO
ZOOM
RATIO
ZOOM
To choose the desired aspect ratio.
Zooms the projector display in or out.
FREEZE
FREEZE
MENU
KEYSTONE
To pause the screen image.
•
Press "MENU" to launch the Onscreen display (OSD) menu, back to the previous step for the OSD menu operation or exit the OSD menu.
•
Confirm your selection of items.
Adjusts the image to compensate for distortion caused by tilting the projector.
7
22
23
24
19
20
21
# Icon
13
14
15
Function
Four directional select keys
Pre./Rewind
Enter/ Play/
Pause
Back/Stop
Next/Fast forward
KeyPad 0~9
16
17
Description
Use up, down, left, right buttons to select items or make adjustments to your selection.
No function.
No function.
No function.
No function.
PgUp/PgDn
Press "0~9" to input a password in the "Security" OSD.
For computer mode only. Use this button to select the next or previous page. This function is only available when USB Ctrl connector (mini type B) is connected to a computer via a USB cable.
COMPONENT No function.
18 VIDEO
VGA
S-VIDEO
SD/USB A
To change source to COMPOSITE VIDEO.
Press "VGA" to change source to the VGA connector. This connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
To change source to S-Video.
No function.
USB B For USB control and firmware upgrade.
HDMI™/MHL To change source to HDMI.
LAN/WiFi No function.
Note: Functions vary depending on model definition.
8
Getting Started
Connecting the Projector
DVD player,
Set-top Box,
HDTV receiver
R B G
HDMI
D-Sub
6
5 8
RS232
R B G
9 10
4
HDMI
7
HDTV adapter
D-Sub
RS232
Video output
Y
3
USB
S-Video output
1
2
4
5
2
3
1
# Description
Power cord
S-Video cable
Composite video cable
RS232 cable
HDMI cable
6
# Description
3 RCA component cable
7
8
VGA to component/HDTV adapter
VGA cable
9 Audio cable jack/jack
10 USB cable
Note 1: To ensure the projector works well with your computer, please make sure the timing of the display mode is compatible with the projector.
Note 2: Functions vary depending on model definition.
Note 3: USB cable needs powered extender if the length is over 5 m.
9
10
Turning the Projector On/Off
Turning on the Projector
1 Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
2 Turn on the projector by pressing "Power" button on the control panel or remote control, and the Power indicator LED will turn blue.
3 Turn on your source (computer, notebook, video player, etc.). The projector will detect your source automatically.
•
•
If the screen displays "Lock" and "Source" icons, it means the projector is locked onto a specific source type and there is no such type of input signal detected.
If the screen displays "No Signal", please make sure the signal cables are securely connected.
• If you connect to multiple sources at the same time, use the "Source" button on either control panel or the remote control or direct source key on the remote control to switch between inputs.
Power button
11
Turning the projector off
1 To turn the projector off, press and hold the power button. This message appears: "Please press the power button again to complete the shutdown process." Press the power button again.
2 The LED power indicator will turn RED and blink rapidly after the projector is turned off, and the fan(s) will continue to operate for about 2 minutes to ensure that the system cools properly. (only supported under "Instant
Resume" mode)
3 As long as the power cord remains plugged in, you can press the power button to turn the projector immediately back on anytime during the 2minute shutdown process. (only supported under "Instant Resume" mode)
4 Once the system has finished cooling, the LED power indicator will stop blinking and turn solid red to indicate standby mode.
5 It is now safe to unplug the power cord.
•
•
Warning indicators:
"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically shut down, and the LED temp indicator will turn solid red. Contact your local dealer or service center.
"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will automatically turn off, the projector will automatically shut down, and the LED temp indicator will blink. Contact your local dealer or service center.
Note 1: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or service center.
Note 2: Functions vary depending on model definition.
Attention! The projector will enter a two minute cool down period to ensure continued optimal lamp operation.
12
Adjusting the Projected Image
Adjusting the Height of Projected Image
The projector is equipped with elevator feet for adjusting the height of image.
To raise/lower the image:
Use Tilt adjusting wheel to fine-tune the display angle.
Tilt adjusting wheel
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the projector is positioned at a desired distance from the screen.
•
SVGA/XGA series
If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 46" and 51".
Note: Remind as below figure, the space of 89 cm height is required when located at 2.0 m distance.
Max scr een siz e
Min scr een siz e
51"
B
13
A
2.0 m
Desired Distance
Height:
80 cm
C
Height: 89 cm from base to top of image
Desired
Distance
(m)
<A>
Screen size
Diagonal
(inch)
<B>
(Min zoom)
W (cm) x H
(cm)
Top
From base to top of image (cm)
<C>
Screen size
(Max zoom)
Top
Diagonal
(inch)
<B>
W (cm) x H
(cm)
From base to top of image (cm)
<C>
1.2
1.5
2
3
4
5
27.34
34
46
68
91
114
8
9
6
7
137
159
182
205
10
11
228
251
11.8
269
Zoom Ratio: 1.11x
56 x 42
69 x 52
93 x 69
139 x 104
185 x 139
231 x 174
278 x 208
324 x 243
370 x 278
417 x 313
463 x 347
509 x 382
546 x 410
240
280
319
359
399
439
471
48
60
80
120
160
200
152
178
203
228
254
279
299.3
30
38
51
76
101
127
62 x 46
77 x 58
103 x 77
155 x 116
206 x 155
258 x 193
309 x 232
361 x 271
412 x 309
464 x 348
515 x 387
567 x 425
608 x 456
267
311
356
400
445
489
525
53
67
89
133
178
222
14
•
WXGA series
If the projector is 2.0 m from the screen, good image quality is possible for image sizes between 54" and 60".
Note: Remind as below figure, the space of 91 cm height is required when located at 2.0 m distance.
Max sc reen siz e
Min sc reen si ze
60"
54"
Height:
82 cm
Height: 91 cm from base to top of image
2.0 m
Desired Distance
Desired
Distance
(m)
<A>
Screen size
(Min zoom)
Diagonal
(inch)
<B>
W (cm) x H (cm)
5
6
3
4
7
1.1
1.5
2
8
9
216
243
10 270
Zoom Ratio: 1.11x
29.69
40
54
81
108
135
162
189
64 x 40
87 x 55
116 x 73
174 x 109
233 x 145
291 x 182
349 x 218
407 x 254
465 x 291
523 x 327
581 x 363
Top
From base to top of image (cm)
<C>
45
61
82
123
163
204
245
286
327
368
408
Screen size
(Max zoom)
Top
Diagonal
(inch)
<B>
W (cm) x H (cm)
33
45
60
71 x 45
97 x 61
130 x 81
From base to top of image
(cm)
<C>
50
68
91
90
120
150
180
210
194 x 121
259 x 162
324 x 202
389 x 243
453 x 283
136
182
227
273
318
241
271
300.69
518 x 324
583 x 364
648 x 405
364
409
455
•
1080p series
If the projector is 2 m from the screen, good image quality is possible for image sizes between 56" and 61".
15
Note: Remind as below figure, the space of 88 cm height is required when located at 2 m distance.
Max sc reen siz e
Min scr een siz e
61"
56"
Height:
81 cm
Height: 88 cm from base to top of image
2 m
Desired Distance
7
8
9
10
3.5
4
4.5
5
6
Screen size
Desired
Distance
(m)
<A>
Diagonal
(inch)
<B>
1.5
41.8
(Min zoom)
W (cm) x H
(cm)
93 x 52
Top
From base to top of image
(cm)
<C>
60
2
2.5
3
56
70
84
123 x 69
154 x 87
185 x 104
81
101
121
195
223
251
279
98
112
125
139
167
216 x 122
247 x 139
278 x 156
309 x 174
370 x 208
432 x 243
494 x 278
556 x 313
617 x 347
282
322
363
403
141
161
181
201
242
Zoom Ratio: 1.1x
107
122
137
153
183
46
61
76
92
214
244
275
305.2
Screen size
(Max zoom)
101 x 57
135 x 76
169 x 95
203 x 114
236 x 133
270 x 152
304 x 171
338 x 190
405 x 228
473 x 266
541 x 304
608 x 342
676 x 380
Top
Diagonal
(inch)
<B>
W (cm) x H
(cm)
From base to top of image (cm)
<C>
154
176
198
220
265
66
88
110
132
309
353
397
441
16
How to get a preferred image size by adjusting distance and zoom
The table below shows how to achieve a desired image size by adjusting either the position or the zoom ring.
•
SVGA/XGA series
To obtain an image size of 50" set the projector at a distance 2.0 m and 2.2 m from the screen.
50"
Desired image size
Height: 88 cm from base to top of image
2.2 m
2.0 m
Desired Distance
Desired Image Size
Diagonal (inch)
<A>
30
40
90
100
150
180
50
60
70
80
200
250
300
Zoom Ratio: 1.11x
W (cm) x H (cm)
61 x 46
81 x 61
102 x 76
122 x 91
142 x 107
163 x 122
183 x 137
203 x 152
305 x 229
366 x 274
406 x 305
508 x 381
610 x 457
Max zoom
<B>
1.2
1.6
2.0
2.37
2.8
3.2
3.5
3.9
5.9
7.1
7.9
9.9
11.8
Distance (m)
Min zoom
<C>
1.3
1.8
4.0
4.4
6.6
7.9
2.2
2.6
3.1
3.5
8.8
11.0
Top (cm)
From base to top of image
<D>
53
70
88
105
123
140
158
175
263
315
351
438
526
•
WXGA series
To obtain an image size of 60" set the projector at a distance 2.0 m and 2.2 m from the screen.
17
60"
Desired image size
Height: 91 cm from base to top of image
2.0 m
2.2 m
Desired Distance
Desired Image Size
Diagonal (inch)
<A>
W (cm) x H (cm)
80
90
100
150
180
30
40
50
60
70
200
250
300
Zoom Ratio: 1.11x
65 x 40
86 x 54
108 x 67
129 x 81
151 x 94
172 x 108
194 x 121
215 x 135
323 x 202
388 x 242
431 x 269
538 x 337
646 x 404
2.7
3.0
3.3
5.0
6.0
1.3
1.7
2.0
2.3
6.7
8.3
10.0
Distance (m)
Max zoom
<B>
Min zoom
<C>
3.0
3.3
3.7
5.6
6.7
1.1
1.5
1.9
2.2
2.6
7.4
9.3
Top (cm)
From base to top of image
<D>
45
61
76
91
106
121
136
151
227
272
303
378
454
18
•
1080p series
To obtain an image size of 60" set the projector at a distance 1.97 m and 2.2 m from the screen.
60"
Desired image size
Height: 87 cm from base to top of image
2.2 m
1.97 m
Desired Distance
Desired Image Size
Diagonal (inch)
<A>
W (cm) x H (cm)
80
90
100
120
150
180
42
50
60
70
200
250
305
Zoom Ratio: 1.1x
93 x 52
111 x 62
133 x 75
155 x 87
177 x 100
199 x 112
221 x 125
266 x 149
332 x 187
398 x 224
443 x 249
553 x 311
675 x 380
1.6
1.97
2.3
2.6
2.9
3.3
3.9
4.9
5.9
6.6
8.2
10.0
Distance (m)
Max zoom
<B>
Min zoom
<C>
2.9
3.2
3.6
4.3
5.4
6.5
7.2
9.0
1.5
1.8
2.2
2.5
Top (cm)
From base to top of image
<D>
61
72
87
101
116
130
144
173
217
260
289
361
441
19
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector installation and maintenance. Use the OSD only when the message "No signal input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance, focus, keystone correction and more.
1 Turn on the projector by pressing "Power" button on the control pad.
2 Press the "MENU" button on the remote control to launch the OSD for projector installation and maintenance.
Installation
Projection Mode
Projection Location
Auto Keystone
Manual Keystone
Language
Reset
Select
Off
English
Press
Adjust Exit
3 The background pattern acts as a guide to adjusting the calibration and alignment settings, such as screen size and distance, focus and more.
4 The Installation menu includes the following options:
•Projection Mode
•Projection Location
•Auto Keystone settings
•Manual Keystone settings
•Keystone settings
•Language settings
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right arrow keys to adjust selected option settings, and the right arrow key to enter a submenu for feature setting. The new settings will be saved automatically upon exiting the menu.
5 Push the MENU button anytime to exit the menu and return to the Acer welcome screen.
Note: Functions vary depending on model definition.
20
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments and change a variety of settings.
Using the OSD menus
•
To open the OSD menu, press "MENU" on the remote control or control panel.
•
When the OSD is displayed, use the main menu. After selecting the desired main menu item, press submenu for feature setting.
•
Use the
keys to select any item in the
to enter
keys to select the desired item and adjust the settings by using the keys.
•
Select the next item to be adjusted in the submenu and adjust as described above.
•
Press "MENU" on the remote control or control panel, the screen will return to the main menu.
•
To exit OSD, press "MENU" on the remote control or control panel. The
OSD menu will close and the projector will automatically save the new settings.
Main menu
Color
Display Mode
Wall color
Brightness
Contrast
Saturation
Tint
Color Temperature
Dynamic Black
Gamma
Advanced
Video
Press
Off
Press
Setting
Sub menu
Select Adjust Main Menu
Note: Some of the following OSD settings may not be available. Please refer to the actual OSD of your projector.
Note: Functions vary depending on model definition.
21
Color
Display Mode
Wall color
Brightness
Contrast
Saturation
Tint
There are many factory presets optimized for various types of images.
•
Bright: For brightness optimization.
•
Presentation: For meeting presentation.
•
Standard: For common environment.
•
Video: For playing video in a bright environment.
•
Game: For game content.
•
Education: For education environment.
•
Movie: For brighter and general movie/video/photo playing.
•
Dark Cinema: For dark movie content.
•
Sports: For sport picture.
•
User: Memorize user's settings.
Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue, pink, dark green. It will compensate the color deviation due to the wall color to show the correct image tone.
Adjust the brightness of the image.
•
Press to darken the image.
•
Press to lighten the image.
"Contrast" controls the difference between the lightest and darkest parts of the picture. Adjusting the contrast changes the amount of black and white in the image.
•
Press to decrease the contrast.
•
Press to increase the contrast.
Adjusts a video image from black and white to fully saturated color.
•
Press to decrease the amount of color in the image.
•
Press to increase the amount of color in the image.
Adjusts the color balance of red and green.
•
Press to increase the amount of green in the image.
•
Press to increase the amount of red in the image.
22
Color
Temperature
Dynamic Black
Gamma
Advanced
Mode
Use this function to choose CT1, CT2 (Native), CT3, User mode.
R Gain
Adjusts the red gain for color temperature optimization.
G Gain
Adjusts the green gain for color temperature optimization.
B Gain
Adjusts the blue gain for color temperature optimization.
R Bias
Adjusts the red bias for color temperature optimization.
G Bias
Adjusts the green bias for color temperature optimization.
B Bias
Adjusts the blue bias for color temperature optimization.
Choose "On" to automatically optimize the display of dark movie scenes enabling them to be shown in incredible detail.
Effects the representation of dark scenery. With greater gamma value, dark scenery looks brighter.
Ind. Color Management
Adjusts the red, green, blue, cyan, yellow and magenta colors.
Ind. Hue
Adjusts the color balance of red and green.
Ind. Saturation
Adjusts the selected color to be less or more saturated color.
Ind. Gain
Adjusts the selected color's contrast.
Brilliant Color
Produces an expanded on-screen color spectrum that delivers enhanced color saturation for bright, true-to-life images.
White Peaking
Increases the brightness of whites that are near 100%. (video sources only)
Film Mode
Sets the image optimized to 24-frame True Film mode.
Noise Reduction
Adjusts signal noise reduction."0" means the noise reduction is off,
">0" increase noise reduction.
Black Extension
This ensures optimum black level for each analog source.
Note 1: "Saturation" and "Tint" functions are not supported under computer or HDMI mode.
Note 2: Functions vary depending on model definition.
23
Image
Projection
•
•
Front-Desktop: The factory default setting.
Rear-Desktop: When you select this function, the projector reverses the image so you can project from behind a translucent screen.
•
Rear-Ceiling: When you select this function, the projector reverses and inverts the image at same time. You can project from behind a translucent screen with ceiling mounted projection.
•
Front-Ceiling: When you select this function, the projector inverts the image for ceiling-mounted projection.
Projection Mode
•
•
Front: The factory default setting.
Rear: Reverses the image so you can project from behind a translucent screen.
Projection Location
•
•
Auto: Automatically adjusts projection location of image.
Desktop
•
Ceiling: Turns the image upside down for ceiling-mounted projection.
Aspect Ratio Use this function to choose your desired aspect ratio.
•
Auto: Keep the image with original width-height ratio and maximize the image to fit native horizontal or vertical pixels.
•
Full: Resize image to fit full screen by width (1280 pixels) and height (800 pixels).
•
4:3: The image will be scaled to fit the screen and displayed using a 4:3 ratio.
•
16:9: The image will be scaled to fit the width of the screen and the height adjusted to display the image using a 16:9 ratio.
•
L.Box: Keep original signal aspect ratio and zoom in by 1.333 times.
Adjust image distortion caused by tilting projection.
Keystone
Auto Keystone Automatically adjusts vertical image.
Manual Keystone Adjust image distortion caused by tilting projection.
Sharpness
<Note> The Manual Keystone function is unavailable under Auto
Keystone setting to "On".
Adjusts the sharpness of the image.
•
Press to decrease the sharpness.
•
Press to increase the sharpness.
24
H. Position
•
Press to move the image left.
•
Press to move the image right.
V. Position
•
Press to move the image down.
•
Press to move the image up.
Frequency "Frequency" changes the projector's refresh rate to match the frequency of your computer’s graphics card. If you can see a vertical flickering bar in the projected image, use this function to make the necessary adjustments.
Tracking
HDMI Color Range Adjust the color range of the HDMI image data to correct color display error.
•
Auto: Automatically adjust by information from player.
•
Limited Range: Process the input image as limited color range data.
•
Full Range: Process the input image as full color range data.
HDMI Scan Info
Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to correct it.
Adjust the overscan ratio of the HDMI image on screen.
•
Auto: Automatically adjust by information from player.
•
Underscan: Always no overscan on HDMI image.
•
Overscan: Always keep overscan on HDMI image.
Note 1: "H. Position", "V. Position", "Frequency" and "Tracking" functions are not supported under HDMI or Video mode.
Note 2: "HDMI Color Range" and "HDMI Scan Info" functions are only supported under HDMI mode.
Note 3: Functions vary depending on model definition.
Setting
Source Lock
Closed Caption
Reset
Security
When Source Lock is turned "Off", the projector will search for other signals if the current input signal is lost. When Source Lock is turned "On", it will "lock" the current source channel unless you press "Source" button on the remote control for the next channel.
Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only available when a composite video or S-Video input signal is selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not available when the aspect ratio is "16:9" or "Auto" .
Press the button and choose "Yes" to return the parameters on all menus to the factory default settings.
Security
This projector provides a useful security function for the administrator to manage usage of the projector.
Press to change the "Security" setting. If the security function is enabled, your must enter the "Administrator Password" first before changing the security settings.
•
Select "On" to enable the security function. The user has to enter a password to operate the projector. Please refer to the
"User Password" section for details.
•
If "Off" is selected, then the user can turn on the projector without password.
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set timeout function.
•
Press or to select the timeout interval.
•
The range is from 10 minute to 990 minutes.
•
When the time is up, the projector will prompt the user to enter the password again.
•
The factory default setting of "Timeout(Min.)" is "Off".
•
Once the security function is enabled, the projector will request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be accepted for this dialogue.
25
26
User Password
•
Press to setup or change the "User Password".
•
Press number keys to set your password on the remote control and press "MENU" to confirm.
•
Press to delete character.
•
Enter the password when you see "Confirm Password" displayed.
•
The password should be between 4 and 8 characters long.
•
If you select "Request password only when plugging the power cord in.", the projector will prompt the user to enter the password every time the power cord is plugged.
•
If you select "Always request password while projector turns on.", the user has to enter the password every time when the projector is turned on.
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•
Press to change the "Administrator Password".
•
The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to retrieve the administrator password:
•
An unique 6-digit "Universal Password" which is printed on the Security Card (please check accessory in the box). This unique password is the number which will be accepted by projector anytime no matter what the Administrator
Password is.
•
If losing this security card and number, please contact with an
Acer service center.
Note: Functions vary depending on model definition.
Management
ECO Mode
High Altitude
Turn Off Mode
Auto Shutdown
Menu Display Time
(Seconds)
AC Power On
Lamp Hour Elapse
Lamp Reminding
Lamp Hour Reset
Choose "On" to dim the projector lamp which will lower power consumption, extend the lamp life and reduce noise. Choose "Off" to return normal mode.
Choose "On" to turn on High Altitude mode. Operate the fans at full speed continuously to allow for proper high altitude cooling of the projector.
•
Instant Off: Shuts down the projector without fan cooling.
•
Instant Resume: Resumes the system when the Power button is pressed again within 2 minutes.
The projector will automatically shutdown when there is no signal input after the allocated time. (default is 15 minutes)
Choose the OSD menu display time. (Default is 15 seconds). Select
“Manual” to turn off main menu/one direct-key menu manually by user.
Choose "On" to power on projector while AC power plug in.
Displays the lamp’s elapsed operating time (in hours).
Activate this function to display a reminder to change the lamp 30 hours before its expected end-of-life.
Press the button and choose "Yes" to turn the lamp hour counter to 0 hours.
27
Audio
Volume
Note: Functions vary depending on model definition.
Mute
•
Press to decrease the volume.
•
Press to increase the volume.
•
Choose "On" to mute the volume.
•
Choose "Off" to restore the volume.
Note: Functions vary depending on model definition.
28
3D
3D Choose "On" to enable DLP 3D function.
•
On: Choose this item while using DLP 3D glasses, 120Hz 3D capable graphics cards and HQFS format file or DVD with corresponding SW player.
•
Off: Turn off 3D mode.
3D Format
24P 3D
If the 3D content is not displayed correctly, you can select a 3D format that suits the 3D content you are viewing and obtain the best result.
Choose "96Hz" or "144Hz" to compatible with 3D glasses.
3D L/R Invert If you see a discrete or overlapping image while wearing DLP 3D glasses, you may need to execute "Invert" to get best match of left/right image sequence to get the correct image (for DLP 3D).
3D Warning Message Choose "On" to display the 3D warning message.
Note: 3D display is now enabled.
1. Please make sure you have the correct 3D signals and glasses.
2. Remember to turn 3D off if you don’t want to see 3D images.
3. If the 3D display isn’t correct, please try to enable 3D Sync Invert.
4. Display mode options will be disabled while in 3D mode.
Note 1: It needs correct settings on graphic card 3D application program for correct 3D display.
Note 2: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players on web page below,
- Stereoscopic Player (Trial): http://www.3dtv.at/Downloads/Index_en.aspx
- DDD TriDef Media Player (Trial): http://www.tridef.com/download/TriDef-3-D-Experience-4.0.2.html
Note 3: "3D L/R Invert" is only available when 3D is enabled.
Note 4: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
Language
Language
Choose the multilingual OSD menu. Use the select your preferred menu language.
•
Press to confirm the selection.
or key to
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following troubleshooting guide. If the problem persists, please contact your local reseller or service center.
29
Image Problems and Solutions
1
#
2
Problem
No image appears onscreen
Partial, scrolling or incorrectly displayed image
(for PC (Windows
2000/XP/Vista/
Windows 7/
Windows 8))
Solution
•
•
•
•
Connected as described in the "Getting Started"
section.
Ensure none of the connector pins are bent or broken.
Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
Make sure you have removed the lens cap and the projector is switched on.
•
Press "RESYNC" on the control panel.
•
For an incorrectly displayed image:
•
Open "My Computer", open the "Control
•
•
Panel", and then double-click the "Display" icon.
Select the "Settings" tab.
Verify that your display resolution setting is lower than or equal to WUXGA-RB (1920 x
1200).
•
•
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display you are using and follow the steps below:
Verify that the resolution setting is lower than
•
•
• or equal to WUXGA-RB (1920 x 1200).
Click the "Change" button under the
"Monitor" tab.
Click "Show all devices". Next, select "Standard monitor types" under the SP box, and choose the resolution mode you need under the
"Models" box.
Verify that the resolution setting of the monitor display is lower than or equal to
WUXGA-RB (1920 x 1200).
30
3
4
5
6
7
Partial, scrolling or incorrectly displayed image
(For notebooks)
The screen of the notebook computer is not displaying your presentation
Image is unstable or flickering
•
•
Image has vertical flickering bar
•
•
Image is out of focus
•
•
•
•
•
•
•
•
Press "RESYNC" on the control panel.
For an incorrectly displayed image:
•
Follow the steps for item 2 (above) to adjust
• the resolution of your computer.
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5]
If you experience difficulty changing resolutions or your monitor freezes, restart all equipment including the projector.
If you are using a Microsoft
®
Windows
®
based notebook: Some notebook PCs may deactivate their own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to your computer's manual for detailed information.
If you are using an Apple
®
Mac
®
OS based notebook: In System Preferences, open Display and select Video Mirroring "On".
Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
Change the display color depth settings on your computer.
Use "Frequency" to make an adjustment. Refer to the "Image" section for more information.
Check and reconfigure the display mode of your graphics card to make it compatible with the projector.
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the required distance of 3.9 to 38.8 feet (1.2 to 11.8 meters) (SVGA/XGA series) / 3.6 to 32.7 feet (1.1 to
10.0 meters) (WXGA series) / 4.9 to 32.8 feet (1.5 to
10.0 meters) (1080p series) from the projector. Refer
to the "How to get a preferred image size by adjusting distance and zoom" section for more
information.
8
9
10
11
Image is stretched when displaying a
"widescreen"
DVD title
Image is too small or too large
Image has slanted sides
Image is reversed
•
•
•
•
•
•
When you play a DVD encoded in anamorphic or 16:9 aspect ratio you may need to adjust the following settings:
•
If you play a 4:3 format DVD title, please change the format to 4:3 in the projector OSD.
•
If the image is still stretched, you will also need to adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
•
If you play an Letterbox (LBX) format DVD title, please change the format to Letterbox (LBX) in the projector OSD.
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the screen.
Press "MENU" on the remote control. Go to "Image -
-> Aspect Ratio" and try different settings or press
"RATIO" on the remote control to adjust directly.
If possible, reposition the projector so that it is centered on the screen.
Press the "Keystone / " button on the remote control until the sides are vertical.
Press "MENU" on the remote control. Go to "Image -
-> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote control.
•
Select "Image --> Projection" on the OSD and adjust the projection direction.
31
32
OSD Messages
1
# Condition
Message
Message Reminder
•
Fan Fail - the system fan is not working.
Fan Fail.
Lamp will automatically turn off soon.
•
Projector Overheated - the projector has exceeded its recommended operating temperature and must be allowed to cool down before it may be used. Please check the following message.
Projector overheated, system will turn off automatically soon, please:
1. Check if operation ambient temperature between 5 degree and 40 degree.
2. Check if filter needs to be cleaned.
3. Check if inlet or outlet is blocked.
4. Check if high altitude mode is set when the projector operating at high altitude area.
Please also check the dust filters if they are installed. If the dust filter is clogged with dust, please clean it. Please refer to
"Cleaning and replacing the dust filters" for details.
•
Replace the lamp - the lamp is about to reach its maximum lifetime. Prepare to replace it soon.
Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!
Problems with the Projector
1
#
2
Condition
The projector stops responding to all controls
Lamp burns out or makes a popping sound
Solution
If possible, turn off the projector, then unplug the power cord and wait at least 30 seconds before reconnecting power.
When the lamp reaches the end of its useful life, it will burn out and may make a loud popping sound. If this happens, the projector will not turn on until the lamp module has been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
33
LED & Alarm Definition Listing
LED Messages
Input power plug
Standby
Message
Power button ON
Lamp retry
Power off (Cooling state)
Lamp_LED
Red
Flash ON to
OFF 100ms
--
--
--
Temp_LED
Red
Flash ON to
OFF 100ms
--
--
--
--
--
--
--
Power LED
Red
Flash ON to
OFF 100ms
Blue
--
ON
--
--
--
ON
Quick
Flashing
-Quick
Flashing
ON -Power button OFF
(cooling completed; standby mode)
Error (thermal failure)
Error (fan lock)
Error (lamp breakdown)
Error (color wheel fail)
--
--
ON
Quick
Flashing
ON
Quick
Flashing
--
--
--
--
--
--
ON
ON
ON
ON
34
Cleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
2
1
Follow these steps:
1 Turn the projector off. Wait for the Power LED to stop flashing then unplug the power cord.
2 Allow the projector at least 30 mins to cool down.
3 Pull out the dust filter. (Illustration #1)
4 To clean the dust filters, use a small vacuum cleaner designed for computers and other office equipment. (Illustration #2)
5 If the dirt is difficult to remove or the filter is broken, please contact your local dealer or service center to obtain a new filter.
35
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!" When you see this message, change the lamp as soon as possible. Make sure the projector has been cooling down for at least 30 minutes before changing the lamp.
1
Warning: The lamp compartment is hot! Allow it to cool down before changing the lamp.
2
3
4
6
5
To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 30 minutes to cool down.
Disconnect the power cord.
1 Use a screwdriver to remove the screw from the cover. (Illustration #1)
Push up and remove the cover. (Illustration #2)
2 Remove the screw that secure the lamp module. (Illustration #3)
Lift the handle so that it stands up. (Illustration #4)
Pull out the lamp plug. (Illustration #5)
3 Lift the handle so that it stands up. Pull out the lamp module by force.
(Illustration #6)
To replace the lamp module, use a new lamp and reverse the above steps.
Warning: To reduce the risk of personal injury, do not drop the lamp module or touch the lamp bulb. The bulb may shatter and cause injury if it is dropped.
36
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the steps below:
1 Drill four holes into a solid, structural ceiling member, and secure the ceiling mount base to the ceiling.
2 Choose the length combination based on actual environment. (CM-01S doesn’t include Type 2 and Type 3.)
Type 1 Type 2 Type 3
37
3 Type 1:
For the standard size use three bracket screws to mount the projector to the ceiling mount bracket.
Type 2 and Type 3:
Alternatively, for the larger size, use the sliding extensions for more supports.
Type 1:
Type 2: Type 3:
Note: It is recommended that you keep a reasonable space between the bracket and the projector to allow for proper heat distribution.
4 Connect the main body connector to the projector bracket (illustration 1), and then screw up four screws (illustration 2).
Illustration 1
Illustration 2
38
5 Adjust the angle and positioning as necessary.
360°
Diameter (mm)
Screw Type B
4
Length (mm)
25
SCREW SPEC. M4 x 25 mm
Large
V
Washer Type
Small
V
55.00 mm 85.00 mm
39
Specifications
The specifications listed below are subject to change without notice. For final specs, please refer to Acer's published marketing specifications.
Projection system
Resolution
Computer compatibility
Video compatibility
Aspect ratio
Displayable colors
Optical zoom ratio
Throw ratio
DLP
®
• X115/D602/EV-S62/V31S/AS304/D600+/X115H/
D602D/EV-S62H/V32S/AS314/D600D+/X114PH series: 800x600 SVGA resolution
•
X125H/D612D/EV-X62H/V32X/AX314/D610D+/
X124PH series: 1024x768 XGA resolution
•
X135WH/D622D/EV-W62H/V32W/AW314/D620D+/
X134PWH series: 1280x800 WXGA resolution
•
H6517ABD/E145F/HE-801K series: 1920x1080 1080p resolution), 1080p(1920x1080), WUXGA-RB
(1920 x 1200)
• Maximum: UXGA (1600 x 1200), WSXGA+
(1680x1050), 1080p(1920x1080), WUXGA-RB
(1920 x 1200)
IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA +
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)
Auto, Full, 4:3, 16:9, L.Box
1.07 billion colors
•
X115/D602/EV-S62/V31S/AS304/D600+/X115H/
D602D/EV-S62H/V32S/AS314/D600D+/X114PH/
X125H/D612D/EV-X62H/V32X/AX314/D610D+/
X124PH/X135WH/D622D/EV-W62H/V32W/AW314/
D620D+/X134PWH series: 1.11X
•
H6517ABD/E145F/HE-801K series: 1.1X
•
X115/D602/EV-S62/V31S/AS304/D600+/X115H/
D602D/EV-S62H/V32S/AS314/D600D+/X114PH/
X125H/D612D/EV-X62H/V32X/AX314/D610D+/
X124PH series:
1.94 ~ 2.16 (51"@2m)
• X135WH/D622D/EV-W62H/V32W/AW314/D620D+/
X134PWH series:
1.54 ~ 1.72 (60"@2m)
•
H6517ABD/E145F/HE-801K series:
1.48 ~ 1.62 (61"@2m)
40
Projection lens
Projection screen size (diagonal)
Projection distance
Horizontal scan rate
Vertical refresh scan rate
Lamp type
Keystone correction
Audio
Weight
Dimensions (W x D x H)
Digital Zoom
Power supply
Power consumption
Operating temperature
•
X115/D602/EV-S62/V31S/AS304/D600+/X115H/
D602D/EV-S62H/V32S/AS314/D600D+/X114PH/
X125H/D612D/EV-X62H/V32X/AX314/D610D+/
X124PH/X135WH/D622D/EV-W62H/V32W/AW314/
D620D+/X134PWH series:
F = 2.41 ~ 2.53, f = 21.85mm ~ 24.01mm,
Manual Zoom & Focus
•
H6517ABD/E145F/HE-801K series:
F = 2.50 ~ 2.67, f = 21.86mm ~ 24.00mm,
Manual Zoom & Focus
•
X115/D602/EV-S62/V31S/AS304/D600+/X115H/
D602D/EV-S62H/V32S/AS314/D600D+/X114PH/
X125H/D612D/EV-X62H/V32X/AX314/D610D+/
X124PH series:
27" ~ 300" (69cm ~ 762cm)
•
X135WH/D622D/EV-W62H/V32W/AW314/D620D+/
X134PWH series:
30" ~ 300" (75cm ~ 762cm)
•
H6517ABD/E145F/HE-801K series:
42" ~ 300" (106cm ~ 762cm)
•
X115/D602/EV-S62/V31S/AS304/D600+/X115H/
D602D/EV-S62H/V32S/AS314/D600D+/X114PH/
X125H/D612D/EV-X62H/V32X/AX314/D610D+/
X124PH series:
1.2m ~ 11.8m (3.9' ~ 38.8')
•
X135WH/D622D/EV-W62H/V32W/AW314/D620D+/
X134PWH series:
1.1m ~ 10.0m (3.6' ~ 32.7')
•
H6517ABD/E145F/HE-801K series:
1.5m ~ 9.8m (4.9' ~ 32.2')
15 - 100 kHz
24 - 120 Hz
195 W user-replaceable lamp
±40 degrees
Internal speaker with 3 W x 1 output
2.5 Kgs (5.51lbs)
314 mm X 223.4 mm X 93.4 mm (12.4" x 8.8" x 3.7")
2X
AC input 100 - 240 V auto-switching power supply
Normal mode: 235W ± 10% @ 110VAC
ECO mode: 195W ± 10% @ 110VAC
Standby mode < 0.5W
0ºC to 40ºC / 32ºF to 104ºF
Standard package contents •
AC power cord x1
•
VGA cable x1
•
Remote control x1
•
Battery x2 (for remote control) (option)
•
User's guide (CD-ROM) x1
•
Quick start guide x1
•
Security card x1
•
Dust filters x1 (option)
•
Carrying case x1 (option)
I/O connectors
Power socket
VGA IN
3.5 mm audio jack input
S-Video
Composite video
RS232
HDMI
Mini USB x1 (for firmware upgrade)
V
V
X
X
X
V
V
X115/D602/
EV-S62/V31S/
AS304/D600+
X115H/D602D/EV-S62H/
V32S/AS314/D600D+/
X114PH/X125H/D612D/
EV-X62H/V32X/AX314/
D610D+/X124PH/
X135WH/D622D/
EV-W62H/V32W/AW314/
D620D+/X134PWH
H6517ABD/E145F/HE-801K
V V
V V
V V
X
X
X
(*)
V
X
V
X
X
V V V
41
Note 1: Design and specifications are subject to change without notice.
Note 2: * Functions vary depending on model definition.
42
Compatibility modes
A. VGA Analog
1 VGA Analog - PC Signal
Modes
VGA
SVGA
XGA
SXGA
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4 i Mac DV (G3)
Resolution
640x480
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
640x480
800x600
1024x768
1152x870
1280x960
1024x768
V.Frequency [Hz] H.Frequency [KHz]
60
72
75
85
31.5
37.9
37.5
43.3
120
56
60
72
75
85
61.9
35.1
37.9
48.1
46.9
53.7
75
85
60
75
85
60
72
120
60
70
75
85
120
70
75
60
60
60
66.6(67)
60
60
75
75
75
65.3
75.0
31.4
34.9
37.9
48.4
68.7
75.0
60.0
77.1
64.0
77.0
80.0
91.1
60.0
75.2
77.4
48.4
56.5
60.0
68.7
99.0
63.8
67.5
43
2 VGA Analog - Extended Wide timing
Modes
WXGA
WSXGA+
WUXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
*1280x800-RB
1440x900
1680x1050
1920x1080
(1080P)
1366x768
1920x1200-RB
V.Frequency [Hz] H.Frequency [KHz]
60
75
85
47.8
60.3
68.6
60
120
60
119.909
60
60
44.8
92.9
49.6
101.6
59.9
65.3
60
60
59.94
67.5
47.7
74.04
3 VGA Analog -Component Signal
Modes
480i
576i
480p
576p
720p
720p
1080i
1080i
1080p
1080p
1080p
1080p
1080p
Resolution
720x480(1440x480)
720x576(1440x576)
720x480
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
*1920x1080
*1920x1080
1920x1080
1920x1080
V.Frequency [Hz] H.Frequency [KHz]
59.94 (29.97)
50(25)
59.94
50
60
50
60(30)
50(25)
23.97/24
25
29.97/30
60
50
37.5
33.8
28.1
27.0
28.1
33.8
67.5
56.3
15.7
15.6
31.5
31.3
45.0
B. HDMI Digital
1 HDMI - PC Signal
Modes
VGA
Resolution
640x480
640x480
640x480
V.Frequency [Hz] H.Frequency [KHz]
60
72
75
31.5
37.9
37.5
44
SVGA
XGA
SXGA
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4 i Mac DV (G3)
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
800x600
1024x768
1152x870
1280x960
1024x768
85
60
75
60
60
60
66.6(67)
120
70
75
85
60
72
75
60
60
75
75
75
75
85
120
60
70
75
85
85
120
56
60
72
91.1
60.0
75.2
65.3
75.0
31.4
34.9
99.0
63.8
67.5
77.1
64.0
77.0
80.0
37.9
48.4
68.7
75.0
60.0
46.9
53.7
77.4
48.4
56.5
60.0
68.7
43.3
61.9
35.1
37.9
48.1
2 HDMI - Extended Wide timing
Modes
WXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
*1280x800-RB
V.Frequency [Hz] H.Frequency [KHz]
60
75
85
47.8
60.3
68.6
60
120
60
119.909
44.8
92.9
49.6
101.6
45
WSXGA+
WUXGA
1440x900
1680x1050
1920x1080
(1080P)
1366x768
1920x1200-RB
60
60
60
60
59.94
59.9
65.3
67.5
47.7
74.04
3 HDMI - Video Signal
Modes
480i
576i
480p
576p
720p
720p
1080i
1080i
1080p
1080p
1080p
1080p
1080p
1080p
Resolution
720x480(1440x480)
720x576(1440x576)
720x480
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
*1920x1080
*1920x1080
1920x1080
* 1920x1200-RB
V.Frequency [Hz] H.Frequency [KHz]
59.94 (29.97)
50(25)
59.94
50
60
50
60(30)
50(25)
23.97/24
60
25
29.97/30
50
59.94
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
27.0
67.5
28.1
33.8
56.3
74.04
4 HDMI - 1.4a 3D Timing
Modes Resolution V.Frequency [Hz] H.Frequency [KHz]
720p (Frame Packing)
720p (Frame Packing)
1280 x 720
1280 x 720
1080p (Frame Packing) 1920 x1080
720p (Frame Packing) 1280 x 720
720p (Frame Packing) 1280 x 720
1080i (Top and Bottom) 1920 x1080
1080i (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
720p (Side by Side (Half)) 1280 x 720
1080i (Side by Side (Half)) 1920 x1080
1080i (Side by Side (Half)) 1920 x1080
50
60
24
50
60
50 (25)
60 (30)
24
50
60
60
50 (25)
60 (30)
27.0
56.3
67.5
45.0
28.1
33.8
37.5
45.0
27.0
37.5
45.0
28.1
33.8
46
1080p (Side by Side (Half)) 1920 x1080 50
1080p (Side by Side (Half)) 1920 x1080 60
Horizontal scan rate:
Graphic source monitor range limits
Vertical scan rate:
Max. pixel rate:
Note: * Functions vary depending on model definition.
56.3
67.5
15k-100kHz
24-120 Hz
Analog:165MHz
Digital:165MHz
47
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
•
•
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to comply with the Class B limits may be attached to this equipment. Operation with non-certified peripherals is likely to result in interference to radio and TV reception.
Caution
Changes or modifications not expressly approved by the manufacturer could void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
48
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
001
Radio device regulatory notice
Note: The regulatory information below is for models with wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any country or region in which it has been approved for wireless use. Depending on configurations, this product may or may not contain wireless radio devices (such as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio communication devices (RSS-210)
a Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
b Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is intended to be operated indoors and installation outdoors is subject to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the country of use. For further information, please contact the local office in the country of use.
Please see http://ec.europa.eu/enterprise/rtte/implem.htm for the latest country list.
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
And,
Acer Italy s.r.l.
Viale De Gasperi 88/A, 20017 Mazzo di Rho (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913 www.acer.it
Product:
Trade Name:
DLP Projector
Acer
Model Number: DSV1527/DSV1523/DNX1522/DWX1521/D1P1532
X115/X115H/X125H/X135WH/H6517ABD/D602/D602D/
D612D/D622D/E145F/EV-S62/EV-S62H/EV-X62H/
EV-W62H/HE-801K/V31S/V32S/V32X/V32W/AS304/AS314/
AX314/AW314/D600+/D600D+/D610D+/D620D+/X114PH/
X124PH/X134PWH
We, Acer Incorporated, hereby declare under our sole responsibility that the product described above is in conformity with the relevant Union harmonization legislations as below Directive and following harmonized standards and/or other relevant standards have been applied:
EMC Directive: 2014/30/EU
EN 55022:2010+AC:2011, Class B
EN 55024:2010
EN 61000-3-2:2006+A2:2009, Class A
EN 61000-3-3:2013
R&TTE Directive: 1999/5/EC (until Jun 12, 2017)
RED Directive: 2014/53/EU (From Jun 13, 2017)
EN 300 328 V1.8.1
EN 301 893 V1.7.1
EN 300 440-1 V1.6.1
EN 300 440-2 V1.4.1
EN 302 291-1 V1.1.1
EN 302 291-2 V1.1.1
EN 301 511 V9.0.2
EN 301 908-1 V6.2.1
EN 301 908-2 V6.2.1
EN 301 908-13 V6.2.1
EN 301 489-1 V1.9.2
EN 301 489-3 V1.6.1
EN 301 489-7 V1.3.1
EN 301 489-17 V2.2.1
EN 301 489-24 V1.5.1
EN 50360:2001
EN 62479:2010
EN 62209-1:2006
EN 50566:2013
EN 62311:2008
EN 62209-2:2010
LVD Directive: 2014/35/EU
EN 60950-1:2006/A11:2009/A1:2010/A12:2011/A2:2013
EN 50332-1:2000 EN 50332-2:2003
RoHS Directive: 2011/65/EU
EN 50581:2012
ErP Directive: 2009/125/EC
Regulation (EU) No. 617/ 2013
Regulation (EC) No. 1275/2008; EN 50564:2011
Regulation (EC) No. 278/2009; EN 50563:2011
Year to begin affixing CE marking 2016.
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147 www.acer.com
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product: DLP Projector
Model Number: DSV1527/DSV1523/DNX1522/DWX1521/D1P1532
Machine Type: X115/ X115H/ X125H/ X135WH/H6517ABD/ D602/
D602D/ D612D/ D622D/ E145F/ EV-S62/ EV-S62H/
EV-X62H/ EV-W62H/ HE-801K/ V31S/ V32S/ V32X/
V32W/AS304/ AS314/ AX314/ AW314/ D600+/
D600D+/ D610D+/ D620D+/ X114PH/ X124PH/
X134PWH
Name of Responsible Party: Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Information for your safety and comfort
- 8 First things first
- 8 Usage Notes
- 8 Precautions
- 9 Contents
- 11 Introduction
- 11 Product Features
- 12 Package Overview
- 13 Projector Overview
- 18 Getting Started
- 18 Connecting the Projector
- 20 Turning the Projector On/Off
- 22 Adjusting the Projected Image
- 29 User Controls
- 29 Installation menu
- 30 Onscreen Display (OSD) Menus
- 31 Color
- 33 Image
- 35 Setting
- 37 Management
- 37 Audio
- 38 3D
- 38 Language
- 39 Appendices
- 39 Troubleshooting
- 43 LED & Alarm Definition Listing
- 44 Cleaning and replacing the dust filters
- 45 Replacing the Lamp
- 46 Ceiling Mount Installation
- 49 Specifications
- 52 Compatibility modes
- 57 Regulations and safety notices