The great outdoors by Minka Lavery | 8272-A357-L | Instructions / Assembly | the great outdoors by Minka Lavery 8272-A357-L Instructions / Assembly

INSTALLATION INSTRUCTIONS
Model # 8272-L /8273-L
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 1)
1. Shut off power at the circuit breaker and remove the old
fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts
in a clear area. Take care not to misplace any small parts
necessary for installation.
3. Hook the ring of the fixture cover onto scroll (V).
4. Align the two nipples of scroll (V) to the pre-drilled holes
of back plate (H).
5. Secure the scroll (V) to back plate (H) with lock washers
(U) and hex nuts (T).
6. Thread the two studs (B) into the pre-drilled holes in the
circular strap (C) spaced the same distance apart as the
holes in the back plate (H). The length of studs (B) into
circular strap (C) may be adjusted if necessary.
7. Attach the circular strap (C) using outlet box screws (F) to
the outlet box (A) (not supplied), (Fig.1).
Fig. 1
Set:
Circular Strap
Ground screw(1)
Mounting screws(2)
CONNECTING THE WIRES (Fig. 2)
8. Connect the electrical wires as shown in Fig.2. Making
sure that all wire connectors are secured. If your outlet
box has a ground wire (green or bare copper), connect
the fixture’s ground wire to it. Otherwise, connect the
fixture’s ground wire directly to the circular strap using the
green screw (D) provided.
F ig.2
FI XTURE
WI RES
GREEN OR
BARE
COPPER
( GROUND)
FI XTURE
WI RES
WHI TE
FI XTURE
WI RES
BLACK
FINISHING THE INSTALLATION (Fig. 1)
9. Align back plate (H) onto studs (B) and secure with cap
nuts (G) (Fig.1).
10. To prevent moisture from entering the outlet box (A) (not
supplied) and causing a short, use clear silicone sealant
to outline the outside of fixture back plate (H) where it
meets the wall leaving a space at bottom to allow
moisture a means to escape (Fig. 3)
11. Bulb ( I ) information (1 x AC LED 10W included.)
(DO NOT EXCEED THE MAXIMUM WATTAGE
RATING) (NE PAS DEPASSER LA PUISSANCE
HOUSE
WI RES
BLACK
( HOT)
HOUSE
WI RES
WHI TE
( NEUTRAL)
HOUSE
WI RES
GREEN OR
BARE COPPER( GROUND)
Fig 3
NOMINALE MAXIMALE!)
12. Replacing LED module (Fig.4)
13.
The LED module can be replaced by a qualified
electrician without cutting of wire and without damage to any
decorative element to which the fixture is attached. See
installation steps for more details (Fig.4).
a. Shut off power, take off the fixture body (S) by loosening
screws (J) (Fig.1), then remove aluminum panel (L) by
loosening screws (M).
b. Remove wire nuts (K), remove screws (O) and carefully
remove LED module (I) for re-lamping. Note: The LED
module should be provided by a specified supplier.
c. For better heat dissipation the LED module (I) should be
installed with the heat transfer material (R) when relamping.
甲、
乙、
Your installation is now complete. Return power to the
outlet box and test the fixture.
Note: Illustration (Fig.1) on this manual is for
installation purposes only. It may or may not be
identical to the fixture purchased.
Caulking
Backplate
Fig. 4
R(Graphite sheet)
Q(Glass)
P(Module ring)
K
L
M
I (LED module)
O(Module screws)
Download PDF