OPERATOR’S MANUAL & PARTS LIST

Predator Automatic Scrubber 16

Model PAS16

WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL

COMPLETELY BEFORE OPERATING THIS EQUIPMENT.

©

Tacony, Inc., All rights reserved

Save These Instructions

PAS16 8/2016

POWR-FLITE PREDATOR AUTOMATIC SCRUBBER 16

This manual refers to a cord electric automatic floor scrubber. Designed to be simple, easy to operate and safe, with maneuverability. Routine maintenance has been simplified and reduced to the minimum to keep equipment on the job.

The objective of this manual is to ensure that the machine is operated correctly and performs the service which we offer to our customers. Therefore, we advise you to follow the instructions it contains scrupulously since the manufacturer accepts no responsibility for damage to persons, or things, or damage to the machine if the machine is not operated the way described in this manual or if the maintenance and safety instructions are not fully complied with.

The instructions provided in this manual do not replace the safety instructions and technical data for installation

and operation directly applied on the product, nor do they replace the safety standards current in the country of installation and the rules dictated by normal common sense.

The operator or maintenance worker must advise a person in authority of any faults or deterioration which could affect the original safety of the machine.

WARNING:

DO NOT OPERATE MACHINE IN AREAS WHERE FLAMMABLE

LIQUIDS OR GASES ARE PRESENT.

DO NOT USE OR PICK UP FLAMMABLE CHEMICALS OR LIQUIDS WITH

THIS MACHINE.

- 2 -

IMPORTANT SAFETY INSTRUCTIONS

All operators must read, understand and practice the following safety instructions. They will be repeated occasionally throughout this manual, and additional warnings may be added for specific cases.

Powr-Flite Predator 16 Electric Auto Scrubber

Your new Powr-Flite ® Electric Auto Scrubber will afford you many years of trouble-free operating satisfaction provided it is given proper care. Prior to packaging, your Powr-Flite ® Auto Scrubber was inspected by a Quality Control Technician.

UNCRATING

Your Powr-Flite ® Electric Auto Scrubber was protectively packed to prevent damage in shipment. We suggest that upon removing the unit from its carton, you carefully inspect it for any possible damage in transit. If damage is discovered, immediately notify the transportation company who delivered your machine. As a manufacturer, we are unable to act upon any claim for concealed damage; you must originate the claim.

IMPORTANT SAFEGUARDS: This machine is designed to be safe when used to perform the functions specified in the

Operator’s Manual. Should damage occur to electrical or mechanical parts, the machine should be repaired by the manufacturer or competent service station before using in order to avoid further damage to the machine or physical injury to user.

WARNING: Never leave the machine unattended, particularly when there are children present.

WARNING: Keep all fasteners tight. Keep adjustments according to specifications.

WARNING: You must have training in the operations of this machine before using it. READ THIS OPERATOR’S

MANUAL.

WARNING: Always use a three-wire electrical system connected to the electrical ground. For maximum protection against electric shock, use a circuit that is protected by a ground fault circuit interrupter. Consult with your electrical contractor.

WARNING: Machines can burn flammable materials and vapors. Do not use this machine with or near fuels, or to pick up grain dust, solvents, thinners, or other flammable materials or liquids.

WARNING: To prevent damage to the power cord, do not let the pad, pad driver, wheels or squeegee touch the power cord when the machine is running. Always lift the power cord over the machine.

WARNING: Do not operate this machine unless it is completely assembled.

WARNING: Make sure all labels, decals, warning, cautions and instructions are fastened to the machine.

WARNING: Do not use this machine as a step or to move furniture.

WARNING: Operators must read and understand this manual completely before operating this equipment.

WARNING: When disconnecting power cord from electrical outlet, grasp the plug. Pulling it out by the cord itself can damage cord insulation and internal connection to plug. To prevent electric shock, always remove the electrical plug from the electrical outlet before doing any repairs or maintenance to this machine.

WARNING: Loose objects on the floor can become dangerous projectiles if struck by the high-speed pad.

Remove them before operating this machine.

WARNING: Keep machine moving to prevent damage to finish or floor.

WARNING: To prevent injury, always remove the electrical plug from the electrical outlet before changing the pad or brush and before leaving the machine.

WARNING: To prevent injury, keep hands, feet and loose clothing away from the rotating pad.

WARNING: Do not operate this equipment in bare feet or with open-toed shoes or sandals.

WARNING: Store or park this machine on a level surface only.

WARNING: Maintenance and repairs must be done by authorized personnel only.

WARNING: These machines are designed for level floor operations only. DO NOT OPERATE on ramps or inclines unless adequate personnel are available for assistance.

WARNING: Never attempt to make emergency repairs or use non-original replacement parts.

WARNING: DO NOT RUN OVER POWER CORD.

WARNING: Keep the electrical parts of this machine dry.

Do not expose electrical components to water or other liquids. To clean machine wipe down with a damp cloth.

Store machine in a building.

- 3 -

TECHNICAL CHARACTERISTICS

POWR-FLITE ® PREDATOR™ 16 AUTO SCRUBBER MODEL PAS16

Technical Specifications ................................................... U.S. Standard ................................................................ Metric

Area per hour ....................................................................... 15,000 sq. feet ................................................................ 1425 sq. meters

Solution Tank ....................................................................... 5.75 gallons .................................................................... 22 liters

Recovery Tank ...................................................................... 5.75 gallons .................................................................... 22 liters

Cleaning Width (brush)......................................................... 16 inches ........................................................................ 400 mm

Squeegee Width ..................................................................... 26.5 inches ..................................................................... 680 mm

Brush Pressure ..................................................................... 50 lbs. ............................................................................. 22 kg

Brush Speed (operating) ....................................................... 290 RPM

Brushes ................................................................................ 16 inches ........................................................................ 400 mm

Brush Motor (power rating) ................................................. 1.0 H.P., 115 volt, 750 watts, 12.6 amp max

Vacuum Motor (power rating) (U.L. Listed) .......................... 1.25 H.P., 115 volt, 1000 watts, 8.0 amp max

Vacuum Water Lift ................................................................. 88 inches

Power Cord (U.L. Listed) ...................................................... 75 feet, 14/3, STW/A ........................................................ 23 meters

Wheels/Casters ...................................................................... 2 Fixed, 2 Casters, Non-Mar Polyurethane

Dimensions - Scrubber.......................................................... 39”L x 18”W x 36”H .................................. 95 cm L x 46 cm W x 90 cm H

Weight .................................................................................. 110 lbs ............................................................................ 50 kg

THE BASIC DESCRIPTION OF THE MACHINE CAN BE SUMMED UP BY THE FOLLOWING FEATURES:

1) Sealed ball-bearing wheels - maintenance free with non-mar polyurethane covered castors and wheels.

2) Unprecedented quality & workmanship, simplified control panel.

3) Hospital quiet, reduced noise level.

4) Bypass vacuum motor with easy access for filter and float cage service.

5) High-speed brush drive with 50 lbs. of contouring pad pressure prevents streaking and produces high productivity.

6) Solution control conveniently located with ease of operation and dispensing control...user friendly...

7) Increased working capacity and productivity offered by higher brush drive speed, increased full contouring pad pressure.

8) 15% fewer working parts and components for trouble free operating and servicing machine.

9) 10 year warranty on housing and tanks.

1 year warranty on brush and vacuum motors.

1 year warranty on parts and workmanship.

10) Rotationally molded design for housing, skirt and tank provide lighter weight, chemical resistance and styling features.

11) Design prevents solution contamination with servicable access to the solution and recovery tanks, vacuum motor.

12) Nylon squeegee body with reversible natural rubber squeegees.

13) Easy “Safe” access to the drive brush for pad or brush removal without requiring tilting of the unit to rear.

14) Squeegee design provides smooth follow operation when cleaning along walls and making runs.

15) Formed one piece zinc-plated frame.

16) Aluminum brush housing with baked enamel finish.

17) Vinyl splash skirt will not corrode.

18) Rear mounted quick release drain hose.

19) Compact and highly maneuverable.

20) Go anywhere portable convenience.

- 4 -

120 Volt

60 Hz

GENERAL OPERATION

Solution Tank: The solution tank is located under the lid, at the front of the machine, with the filling-funnel M1 in an accessible position for easy re-filling.

WARNING: Always switch off and unplug the machine before filling the solution tank.

Note: Always empty the dirty water collection tank, as described in the next paragraph, before refilling the tank with the diluted detergent solution. The solution tank has a maximum capacity of 5.75 gallons (22 liters). Always use the products and the dilution quantities recommended by the seller. Always use low foam detergents. Use defoamer if excess foam develops.

Remove hose from vac intake and pick up defoamer directly into the recovery tank.

Water collection tank: The dirty water collection tank should be emptied, preferably each time after use, so that the dirt

- 5 does not settle there. To do this, remove the plug of the drain hose M2, which is kept in position by a simple spring clip, and empty dirty water into the proper drain conforming to local regulations.

Squeegee: The squeegee has the final task of completing the drying of the floor and it is very important for it to be in the correct position. Lower the squeegee to the working position by depressing pedal M3 as shown. Adjust the position of the squeegee by means of the knobs M4 so that the black rubber bar is about 1 ⁄32” (the thickness of a business card) from the floor. The squeegee behind this is in para rubber and must press on the floor with a certain amount of force.

After the first few hours the squeegee adjusts itself

to the correct angle and drying becomes even better.

Squeegee pressure is adjusted by knob M14.

GENERAL OPERATION

The area to be scrubbed: Debris and grit must be swept up before starting the scubbing operation to avoid vacuum line blockage and to permit the detergent to perform efficiently.

Prior to startup and operation: Caution: A) Loose objects on the floor can become dangerous projectiles if struck by the high speed pad. Remove them before operating machine. B) Keep machine moving to prevent damage to finish or floor.

C) These machines are designed for level floor operations only.

DO NOT OPERATE ON RAMPS OR INCLINES unless adequate personnel are available for assistance.

Starting up and operation: Plug the machine into an outlet position allowing operation by moving away from the outlet.

NOTE: The PAS16 is intended for use with 120V/60Hz cycle grounded circuit. Extension cords are not recommended.

Then:

• Press switches M7 and M8.

• Lower the brush by pressing pedal M9.

• Lower the squeegee by depressing pedal M3.

• Set the detergent solution supply to minimum by adjusting knob M12. Experience will help with the selection of the correct solution amount. Moving outward up and down as illustrated, allows cord to keep off of dirty floor and from draging dirt into cleaned path.

• Finally, adjust the correct supply of detergent in proportion to the amount of dirt and amount of speed of advance by means of lever M12; this is a matter of experience. At this point the machine is ready to carry out the operations of scrubbing and drying at the same time.

Particularly dirty floors: Certain floors or areas may require special attention and, in some cases, cleaning twice. Go over the floor quickly the first time, with the squeegee raised and the brush in the working position. In this way, the detergent solution is left on the floor for a longer time and can dissolve the heavy dirt. The

- 6 -

GENERAL OPERATION

second time, go over the floor more slowly with both the brush and the squeegee lowered. Always apply and brush stripping solution without squeegee and vacuum then return to area after a minimum of 5 minutes and remove the suspended dirt, finish and solution.

Squeegee: Every week, check the blades of the squeegee and wash them carefully. Then replace them in the correct working position. If drying is not perfect even after the unit has been cleaned, replace any blades which are excessively worn. If the squeegee does not pick up enough water or streaks, lift and wipe off the blades.

The pad driver or brush must be in good working condition because it is the component which removes the dirt.

To remove the drive block, pad or brush:

• Fold the vinyl bumper over the left side of the

brush housing.

• Depress the brush pedal (M9) with your right hand

hold the brush position to allow free spinning by hand

of the driver or brush until the scissors style spring

lock can be squeezed with your left hand.

• Depress the brush pedal (M9) completely down

clearing the brush or drive block and slide brush or

driver out from under the housing.

To replace the drive block, pad or brush:

• Hold the brush pedal (M9) down while centering

the brush or driver under coupling. While squeezing the

spring lock together lower the coupling into the driver or

brush center by allowing the brush pedal to raise.

Release the scissors spring lock

The machine is supplied with a pad driver. Brushes in tynex, poly and steel are available on request, together with floor pads recommended for use with the pad driver. Black for stripping,

green for deep scrub, blue for cleansing and red for light scrub.

Water collection tank: This tank should be cleaned every week.

Lift the lid and remove the panel or funnel M1 of the solution tank.

Remove the strap M13 and lift the vacuum motor out of its seat.

Thoroughly clean the filter and wash out the dirt deposited in the tank with a jet of water, allowing it to drain out through hose M2.

If necessary, replace filter. Replace float cage with open side facing front of scrubber.

- 7 -

PARTS LIST

Pos Part No. Description

1 410.001 Cover

2 PAS260 Cover

3 410.003 Housing

4 PAS311

5 PAS304

6 PAS312

7 PAS125

8 PAS153

9 PAS306

10 PAS245

11 M1400

Cover Nut

Nut

Cover Washer

Switch

Screw, Stainless

Control Panel

Strain Relief

14/3 - 75’ Cord

Pos Part No. Description

12 500.158 Washer

13 410.013 Screw, Stainless

14 PAS197 Screw 6mm

15 PAS311 Cover Nut 6mm

16 410.016 Support

18 PAS126 Wheel

19 400.050 Screw 6mm

20 400.049 Pin

21 410.021 Panel

22 410.022 Screw

23 PAS211 Strap

Pos Part No. Description

24 PAS128 Bumper

25 PAS18

26 PAS32

Spring Handle

Tie Rod

28 PAS127 Caster

30 PAS311 Nut 6mm

31 PAS250 Housing Brush

32 410.032 Screw, Stainless

33 PAS303 Hinge

34 400.146 Block

35 PAS267 Cable Swivel

36 PAS122 Hook & Latch Assy.

- 8 -

PARTS LIST

Pos Part No. Description

41 PAS314 Solution Tank

42 PAS3 Screen

43 PAS11 Knob

44 410.044 Rod

45 410.045 Plate

46 PAS147

47 500.056

Screw 6mm

Split Pin

48 500.062 Washer

49 500.054 Screw 5/32”

50 500.051 Lever

51 431.065 Screw 6mm

52 PAS258 Bracket

53 410.053 Spring

54 PAS14 Foot Pedal Cover

55 PAS63 Pin/Tie Rod

56 410.056 Lever

57 410.057 Bracket

Pos Part No. Description

58 410.058 Bracket

59 PAS167 Screw 8mm

60 430.117

61 430.117

Nut 8mm

Nut 8mm

62 PAS188 Washer

63 410.063 Washer

64 410.064 Washer

65 410.065 Support

66 PAS311 Nut 6mm

67 PAS167

68 PAS97

68.1 PAS99

68.2 PAS131

68.3 PAS134

68.4 PAS98

Screw 8mm

Poly Scrub Brush

Powr-Nylon Brush

Strata Grit Brush

Powr-Scuff Brush

Powr-Scrub II

69.1 PAS6A Support with Spring

70 PAS65 Screw

Pos Part No. Description

71 430.072 Screw

72 PAS5 Coupling Half

73 430.072 Screw

74 430.071 Washer

75 PAS65 Washer

76 410.076 Plate

77 PAS305-2 Geared Motor 220v

PAS305 Geared Motor 110v

78 PAS167 Screw 8mm

79 500.048 Valve

80 400.161 Nut 3/8”

81

82

83

PAS42 Hose Clamp

PAS288 Hose

PAS288 Hose check for #99 bolt look on pas28

- 9 -

Serial numbers at or below 05-9703684 have lever squeegee adjustment

PARTS LIST

Pos Part No. Description

100 PAS15 Strap

102 1973 Vac Motor

103 PAS102 Gasket Motor

105 PAS198 Tie Rod

106 PAS311 Nut M6

107 F909 Filter/Screen

108 PAS85 Float Cage

109 PAS210 Float

110 PAS103 Seal

111 PAS37 Drain Hose

112 PAS38 Hose Clamp

113 430.194 Washer

114 430.192 Nut M4

115 410.115 Plate

116 PAS147 Srew

117 PAS266 Split Pin

118 PAS315 Bracket

119 PAS32 Tie Rod

120 PAS35 Knob M6

121 PAS33 Ring-nut

122 PAS34 Adjusting Screw

123 PAS191 Clamp, Hose

Pos Part No. Description

124 500.157 Pin

125 PAS19 Pin Squeegee Mt.

126 400.129 Shaft

127 PAS264 Support

128 PAS936 Screw

129 PAS935 Nut 10mm

130 PAS31 Spring

131 PAS304 Nut 6mm

132 PAS197 Washer 6mm

133 430.198 Outer Bar

134 PAS 302 Black Rubber

135 PAS300R Squeegee Body

136 PAS 300 Main Squeegee Blade

137 PAS240 Squeegee Complete

(*) PAS 124 Squeegee Blade Set

138 430.204 Outer Bar

139 410.139 Pedal

139.1 PAS129 Cable

140 410.140.1 Connecting Rod

140.1 410.140 Connecting Rod

141 PAS259 Cross Member

141-1 PAS313 Dowel M8

- 10 -

Pos Part No. Description

142.1 410.142 Lever

143.1 400.127 Knob

144.1 400.148 Pivot Block

145.1 430.156 Dowel

146.1 430.159 Seeger, Clamp

147 PAS26 Tank

148 PAS37 Intake Hose

149 PAS36 Plug

150 PAS51 Wheel, Bumper

151 PAS193 Support Stud

152 F940 Foam Filter

ELECTRICAL DIAGRAM

BROWN

BLUE

LITE BLUE

LITE BROWN

GREEN/YELLOW

BLUE

BROWN

BLUE

BROWN

LITE BLUE

TAN

VAC

MOTOR

BRUSH

MOTOR

Pos Part No. Description

181 M1400 14/3, 75’ Cord

183 PAS125 Switch

Pos Part No. Description

184 1972 Suction Motor

185 430066E Brush Motor

Pos Part No. Description

187 PAS309 Connecting Board

- 11 -

A Tacony Company

3101 Wichita Court • Ft. Worth, TX 76140-1755

1-800-880-2913 • Fax: 1-817-551-0719 • www.Powr-Flite.com