The great outdoors by Minka Lavery | 72425-212 | Instructions / Assembly | the great outdoors by Minka Lavery 72425-212 Instructions / Assembly

INSTALLATION INSTRUCTIONS
For Model 72425-212 (Rev. 02/22/2014)
READ AND SAVE THESE INSTRUCTIONS
W A R N I N G ! S H U T P O W E R O F F AT F U S E O R C I R C U I T B R E A K E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARING FOR INSTALLATION (Fig. 2)
1.
2.
3.
4.
5.
6.
7.
8.
9.
Shut off the power at the fuse box or circuit breaker box and
remove the old fixture from the ceiling, including the mounting
hardware.
Carefully unpack your new fixture and lay out all the parts in a clear
area. Take care not to misplace any small parts necessary for
installation.
Thread the nipple into the ceiling loop until snug.
Thread the other end of the nipple into the crossbar until snug.
Note: The length of the nipple into the crossbar may be adjusted if
necessary.
Use the lock washer and hex nut to secure the nipple into the
crossbar.
Take this crossbar assembly and mount it to ceiling outlet box with
mounting screws (Size: #8-32N*L0.5”). The side of crossbar
marked with “GND” must face out.
Determine the desired hanging height and use a pair of proper
chain pliers to remove and discard the excess chain.
Open one end of chain and attach it to the fixture loop and close
the chain. Slip the canopy and lock collar over the chain and allow
them to rest on the fixture body. Open the other end of the chain
and attach it to ceiling loop and close the chain.
Carefully lace the fixture’s wires through the chain. Feed the fixture
wires through the loop and nipple assembly.
Fig.1
Set# A-010
- Crossbar
- Ground screw
- Mounting Screw*2
A
C
B
CONNECT THE WIRES (Fig. 3)
10. Connect the electrical wires as shown in Fig. 3, making sure that
all wire connectors are secured. If your outlet box has a ground
wire (green or bare copper), connect the fixture’s ground wire to it.
Otherwise, connect the fixture’s ground wire directly to the
crossbar using the green screw provided.
11. Tuck these wire connections neatly into the ceiling outlet box and
then raise the canopy all the way to the ceiling. Raise the lock
collar and thread onto ceiling loop protruding through canopy
(Fig.2).
Fig.2
Outlet Box
Hex Nut
Crossbar
COMPLETING THE INSTALLATION (Fig. 1)
12. Pull up the latch (B) and open the door.
13. Then install the glass (C) using the glass clips on the frame (A).
(Note: Install the back glass first followed by the side glass. The
front glass should be installed last)
14. Install 4*60W B10.5 bulb(s) (not included) in accordance with the
fixture’s specification. (DO NOT EXCEED THE MAXIMUM
WATTAGE RATING)(NE PAS DEPASSER LA PUISSANCE
NOMINALE MAXIMALE!).
15. When replacing the glass (C), pull up the latch (B) and open the
door. Loosen the clips and remove glass (C). (Note: You must
remove the side glass, just remove the back glass.) After replacing
the glass, repeat step 13, and then close the door.
16. For installing or replacing bulbs at a later date, pull up the latch (B)
and open the door. (Fig.1)
Lock Washer
Mounting Screw
Nipple
Ceiling Loop
Chain
Canopy
Lock Collar
Chain#HCH2072-212
Wire
Loop
Fig. 3
FIXTURE
WIRES
Black or
Smooth
FIXTURE
WIRES
White or
Ribbed
FIXTURE
WIRES
Bare
Copper
(Ground)
Your installation is now complete. Return power to the junction box
and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation
purposes only. It may or may not be identical to the fixture
purchased.
HOUSE
WIRES
Black
(Hot)
Notice: It is important to use proper chain pliers (not included)
To OPEN and CLOSE the chain included with this fixture. Do
not open them with other tools that may twist or stress the
chain links. It is important to use proper chain pliers like the
ones shown in the diagram.
LA-2397E
HOUSE
WIRES
White
(Neutral)
HOUSE
WIRES
Green
(Ground)
Download PDF