AVE HOME - Stasanet
AVE HOME
CVBS TO DVB-T ENCODER
MODULATOR
FAGOR�
Fagor Electr6nica
TABLE OF CONTENTS 1. SPECIFICATIONS ........................................................................................................................... 12 1.1 Product Overview .................................................................................................................. 12 1.2 Appearance and Description .................................................................................................. 12 1.3 System Diagram ..................................................................................................................... 13 1.4 Characteristics ........................................................................................................................ 13 2. Installation Guide and Safety Instructions ................................................................................... 14 2.1 Safety Instructions ................................................................................................................. 14 2.2 Installation ............................................................................................................................. 14 3. Operation ..................................................................................................................................... 16 1. SPECIFICATIONS 1.1 Product Overview AVE Home encoder & modulator allows audio/video signal input in TV distributions with applications in home entertainment, surveillance control, hotel Digital Signage, shops etc. It is an all-­‐in-­‐one device integrating MPEG2 encoding and DVB-­‐T modulating to convert input signals to DVB-­‐T RF out in the frequency range of 30~960MHz. The signals source could be from satellite receivers, closed-­‐circuit television cameras, Blue-­‐ray players, and antenna etc. its output signal is to be received by DVB-­‐T standard TVs or DVB-­‐T STBs etc. 1.2 Appearance and Description Grounding DC 12V CVBS L/R channel RF in RF out
Grounding: to connect the earth cable DC 12V: power input CVBS: composited video input supporting NTSC and PAL L/R channel: Stereo Left and Right audio channels RF in: RF Loop-­‐through input (10dB attenuation) RF out: RF output to distribute modulated signal (30-­‐960 MHz, 71~91 dBµV) LCD Window Control Buttons Indicators Air Vent JTAG port for upgrade 1.3 System Diagram AVE HOME Encoder Modulator
Surveillance Monitor
DVD
Signal Source
Encoder
Modulator
Combiner
RF out
Attenuation: 10dB
STB/IRD
RF in
Antenna
Camera
Closed Circuit TV
PC
TV+AV to the distribution network
1.4 Characteristics Encoding Section Video Audio Encoding MPEG-­‐2 MP@ML(4:2:0) Interface CVBS *1 Resolution 720x576_50i (PAL); 720x480_60i (NTSC) Bit rate 1.000~19.500 Mbps Encoding MPEG1 Layer II Interface 1*Stereo /mono Sample rate 48KHz Bit rate 64, 96, 128, 192, 256, 320, 384kbps Modulator Section Standard DVB-­‐T COFDM Bandwidth 6M, 7M, 8M Constellation QPSK, 16QAM, 64QAM, Code rate 1/2, 2/3, 3/4, 5/6, 7/8. Guard Interval 1/32, 1/16, 1/8, 1/4. Transmission Mode: 2K, 8K MER ≥42dB RF frequency 30~960 MHz, 1KHz step RF output level -­‐16~ -­‐36 dBm (71~91 dBµV), 0.1db step System Management Local control: LCD + control buttons Language English LCN Insertion yes Upgrade JTAG or USB General Power supply DC 12V Dimensions 153*110*50mm Weight 1kg Operation temperature 0~45℃ 13 2. Installation Guide and Safety Instructions 2.1 Safety Instructions WARNING: To prevent fire or electrical shock, do not expose the device to rain or moisture. The encoder modulator is powered with a voltage of 12V DC. The power supply voltage must not exceed the recommended voltage, which otherwise may cause irreparable damage to the device and the invalidation of the warranty. Therefore: l
l
l
l
Do not replace power supply with a voltage greater than 12V DC. Do not connect the device to the power if the power cord is damaged. Do not plug the device into mains supply until all cables have been connected correctly. Do not cut the cord. Avoid placing the device next to central heating components and in areas of high humidity. Do not cover the device with elements that obstruct the ventilation slots. If the encoder modulator has been kept in cold conditions for a long time, keep it in a warm room minimum 2 hours before plugging into the mains. Mount the device in vertical position with the connectors located on the top side. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutes may result in fire, electric shock or other hazards. Safety check-­‐ Upon completion of any service or repairs to this device, ask the service technician to perform safety checks to determine that the device is in proper condition. 2.2 Installation RISK OF damage to the unit Mechanically handling the unit may result in damage. Do not connect the unit to the power supply before or during assembly. Connect the unit as below instructed. 1. Mount and tighten the screws and plugs to secure the unit to the wall. Left 10 cm of free space around from each unit. 2. Connect the signal input in the respective connectors. The signal source can be from a surveillance monitor, DVD, set-­‐top box, CCTV and etc. 3. Optionally, connect the loop-­‐through RF input
coaxial cable. 4. Connect cable to RF output to STB/TV. 5. Power supply connection: a) Connect the earth cable; b) Connect the power plug to the unit mains connector; c) Connect the power plug to the mains socket. Cascade Installation AVE Home unit has 1 TV signal to RF output encoded as DVB-­‐T Digital TV signal. Several AVE Home units can be cascaded in order to increase the capacity. To cascade 2 or more units, connect the RF output of the preceding unit to the TV input (loop-­‐through) of the next unit (see right illustration). 15 3. Operation AVE HOME is controlled and managed through the key board and LCD display. LCD Display – It presents the selected menu and the parameter settings. The backlight in the display is on when the power is applied. LED – These lights indicate the working status l Power: It lights on when the power supply is connected. l Alarm: It lights on when there is error, such as the signal source loss. l Lock: It lights on when the signal source connected and goes off when the signal lose. Enter
Audio Bit rate
*128
Enter
►
Hue
+001
►
Audio Bit rate
128
Hue
+001
►
Enter
Audio Bit rate
►128
►
Hue
1
►
Left/Right/Up/Down buttons – Use these buttons to turn the screen pages, shift the target items by moving the triangle, or change the parameter settings in the program mode. Enter – Use this button to enter a submenu or save a new setting after adjustment; press it to start adjusting the value of certain items when the corresponding underline flash with Up and Down buttons; Hue
+002
Press it to activate the hidden selections and change the setting with Up and Down (or Left and Right) buttons. ►
Audio Bit rate
►192
Menu – Press this button to step back Lock – Locking the screen / cancelling the lock state, and entering the main menu after the initialization of the device. After pressing lock key, the system will question the users to save present setting or not. If not, the LCD will display the current configuration state. When the power is connected, the LCD will start to initialize the program. The LCD menu goes as below chart. Initializing
DVB-T 650.000M U
1080i
6.93Mbps
Main Menu
Status
Main Menu
Encoder
Main Menu
Modulator
Up
Down
Enter
Menu
Lock
1
Status
Alarm
2
Status
Uptime
3
Encoder
Video
Video
Video In Status
Norm
Resolution
.
.
.
Aspect Ratio
Encoder
Audio
Audio
Audio Bitrate
Broadcast
Encoder
Program Info
Program Info
Program Output
Program Name
.
.
.
.
LCN
EIT Event
4
5
6
Modulator
Bandwidth
Bandwidth
►8M 7M 6M
7
Modulator
Constellation
Constellation
►64QAM
8
Modulator
FFT
FFT
►2K
9
Modulator
Guard Interval
Guard Interval
►1/32
10
Modulator
Code Rate
Code Rate
►7/8
11
Modulator
RF Frequency
RF Frequency
650.000 MHz
12
Modulator
RF Level
RF Level
-10.0 dBm
13
Modulator
RF On
RF On
Off
*On
14
Modulator
Bit Rate
Bit Rate(val/max)
6.986M/31.668M
15
8K
17 Main Menu
Stream
Stream
TSID
16
Stream
ONID
17
Stream
NIT
NIT
Network ID
Network Name
LCN Mode
Private Data
NIT Insert
Stream
EIT
Main Menu
System
18
EIT
Language code
EIT insert
19
System
Save Config
Save Config?
Yes
►No
20
System
Load Saved CFG
Load SavedCFG?
Yes
►No
21
System
Factory Reset
Reset all sets?
Yes
►No
22
System
LCD Time-out
LCD Time-out
►30 s
23
System
Key Password
Set Password
000000
24
System
Lock Keyboard
Lock Keyboard
Yes
►No
25
System
Serial number
0035564905656
70ec8f7b0000f
26
System
Version
Encoder Modulator
SW:x.xx HW:x.xx
27
1) DVB-­‐T: modulating standard; XX.XXX M: the current output frequency; U: symbol of the USB disk insertion; 1080i: video resolution of signal source; X.XX Mbps: the current encoding bit rate 2) Alarm Status: For example, if the signal cable disconnected, it will display Video 1 Not Lock under this menu. 3) Uptime: It displays the working time duration of the device. It times upon power on. 4) Video Parameters: User can enter the items respectively to set the input interface and view the video status. User can also adjust values of rest items (Bit rate: 0.500~19.500 Mbps; Brightness & Contrast & Saturation: 0-­‐255; Hue: -­‐128 -­‐ +127). 5) Audio Bit rate: Select audio bit rate among 64, 96, 128, 192, 256, 320, 384 kbps. Audio Broadcast: Enable – the output program will broadcast only audio without the picture; Disable – cancel broadcast mode to resume both audio and video. 6) Program Information: User can enable or disable the program output under menu Program Output. User can also enter the other items to edit the Service Name, Program Name, Program Number, and PIDs of PMT, PCR, Video and Audio, and edit LCN (Logical channel number). EIT Event – User can enter this menu to setup EIT (Event Information Table) for the current and next program event. The EIT contains Start Year, Start Time, Duration, and Event Name of the event. All the EIT information can be displayed on the TV screen on condition that the EIT is chosen to insert (see explanation 19). 7) Bandwidth: choose between 6M, 7M and 8M. 8) Constellation: DVB-­‐T modulator contains 3 constellation modes – 64 QAM, QPSK and 16 QAM. 9) FFT (Transmission Mode): 2K and 8K. 10) Guard Interval: Select among 1/32, 1/16, 1/8 and 1/4. 11) Code Rate: It refers to FEC-­‐Forward Error Correction rate. It contains 1/2, 2/3, 3/4, 5/6 and 7/8. Ø NOTE: The different combination of bandwidth, constellation, guard interval and code rate (FEC) will form a different output code rate. Please refer to appendix table 2. 12) RF Frequency: Adjust it at range of 30 to 999 MHz. Set it according your regional situation or inquire your local services. 13) RF Level: Adjust it at range of -­‐16~ -­‐36dBm. 14) RF On: User can choose to turn on or turn off the RF under this menu. 15) Bit Rate: User can read the current modulating bit rate and the maximum bit rate 16) TSID: (Transport Stream ID) User can view or adjust after enter this menu. 17) ONID: (Original Network ID)-­‐User can view or adjust after enter this menu. 18) NIT: (Network Information Table) NIT table is a very important table for describing the network and TS. User can enter the submenus displayed and edit the values or select the LCN (Logical channel number) mode, and choose whether to insert the NIT. If user chooses to insert the NIT, information (Network ID, Network Name, LCN Mode, NIT Version Private Data and LCN number of the program mentioned in explanation 6) will be added to the transport stream. Ø NOTE: when the Private Data is set as 0*0, it is invalid. 19 19) EIT: EIT Insert -­‐ As mentioned above (6), the event information table can be chosen whether to insert into the TS or not under this menu. If yes, the EIT information set above (6) will be displayed on the TV screen. Language Code – to set the EIT language For example, code of the English language is eng. If you set the code as eng, the EIT displayed will be in English language. 20) Save Config: Yes/No-­‐to save/give up the adjustment of setting. 21) Load Saved CFG: Yes/No-­‐to load/ not to load the saved configuration. 22) Reset all sets: Yes/No-­‐choose/not choose the factory’s default configuration. 23) LCD Time out: A time limit that LCD will light off. Choose among 5s, 10s, 45s, 60s, 90s and 120s (seconds). 24) Key Password: User can set a 6-­‐digital password used to unlock the keyboard. 25) Lock Keyboard: Choose Yes to lock the keyboard, then the keyboard cannot be applicable. It is required to input the password to unlock the key board. This operation is one-­‐off. (If forgetting your password, please use the universal code “005599”.) 26) Serial number: User can view the serial number of this device. It is read-­‐only and unique 27) Version: It displays the version information of this device. Encoder Modulator: the name of the device; SW: software version number; HW: hardware version number. User can also press ENTER again to view the published time of this device. Appendix Modulation Constellation QPSK 16QAM 64QAM FEC 1/2 2/3 3/4 5/6 7/8 1/2 2/3 3/4 5/6 7/8 1/2 2/3 3/4 5/6 7/8 6MHz Bandwidth 7MHz Bandwidth Guard Interval Guard Interval 1/4 1/8 1/16 1/32 1/4 1/8 1/16 1/32 1/4 The weak ability of error-­‐correcting and anti-­‐interference in this area 6.03 5.80 6.45 6.83 7.03 6.64 6.22 6.58 6.78 6.53 7.25 7.68 7.91 7.46 6.22 6.91 7.31 7.54 7.25 8.06 8.53 8.79 8.29 6.53 7.25 7.68 7.91 7.62 8.46 8.96 9.23 8.71 7.46 8.29 8.78 9.04 8.70 9.67 10.24 10.55 9.95 9.95 11.05 11.70 12.06 11.61 12.90 13.66 14.07 13.27 11.19 12.44 13.17 13.57 13.06 14.51 15.36 15.83 14.93 12.44 13.82 14.63 15.08 14.51 16.12 17.07 17.59 16.59 13.06 14.51 15.36 15.83 15.24 16.93 17.93 18.47 17.42 11.19 12.44 13.17 13.57 13.06 14.51 15.36 15.83 14.93 14.92 16.58 17.56 18.09 17.41 19.35 20.49 21.11 19.91 16.79 18.66 19.76 20.35 19.59 21.77 23.05 23.75 22.39 18.66 20.73 21.95 22.62 21.77 24.19 25.61 26.39 24.88 19.59 21.77 23.05 23.75 22.86 25.40 26.89 27.71 26.13 Table 1 Channel output max. capacity in Mbps 8MHz Bandwidth Guard Interval 1/8 1/16 1/32 6.03 7.37 7.81 8.04 8.29 8.78 9.05 9.22 9.76 10.05 9.68 10.25 10.56 11.06 11.71 12.06 14.75 15.61 16.09 16.59 17.56 18.10 18.43 19.52 20.11 19.35 20.49 21.11 16.59 17.56 18.10 22.12 23.42 24.13 24.88 26.35 27.14 27.65 29.27 30.16 29.03 30.74 31.67 CVBS to DVB-­‐T Encoder Modulator 1.
2.
3.
4.
Stream -­‐> TSID = un numéro différent aux multiplex reçus dans la télé, peut être « 1 ». Stream -­‐> ONID = 8442 « France » Stream -­‐> NIT-­‐> Network ID = 8442 Stream -­‐> NIT -­‐> NIT insert = yes « imperative” 5. Encoder -­‐> Program Info -­‐> LCN = un numéro différent des autres LCN reçus dans la télé. 31 
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising