Sea gull lighting | 31051-71 | Installation guide | Sea Gull Lighting 31051-71 Installation Guide

Installation And Safety Instructions
HC-652
Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to
this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________
072208
IMPORTANT SAFETY INSTRUCTIONS
•
•
•
•
•
•
•
•
Be sure the electricity to the system you are working on is turned
off; either the fuse removed or the circuit breaker set at off.
Use of other manufacturers components will void warranty, listing
and create a potential safety hazard.
If you are unclear as to how to proceed, contact a qualified
electrician.
You don’t need special tools to install this fixture.
Be sure to follow the steps in the order given.
Under no circumstances should a fixture be hung on house
electrical wires, nor should a swag type fixture be installed on a
ceiling which contains a radiant type heating system.
Read instructions carefully.
Save these instructions.
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
PERSONAL INJURY, MOUNT TO OUTLET BOX OR SUPPORTING SYSTEM
ABLE TO SUPPORT THE WEIGHT OF THE FIXTURE.
CLEANING
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders,
steel wool or abrasive paper.
ORDERING PARTS
*OUTLET BOX
*HOUSE
GROUND
WIRE
*WIRE
CONNECTORS
MOUNTING
BAR (A)
GREEN
GROUNDING
SCREW (G)
*OUTLET BOX
SCREWS
NUT &
LOCKWASHER
(B)
NIPPLE (C)
FIXTURE
GROUND
WIRE (F)
SCREW
COLLAR (D)
CANOPY (E)
Keep this sheet for future reference, and in case you need to order
replacement parts. Parts for this fixture can be ordered from place
of purchase. Be sure to use exact wording from illustration when
ordering parts.
BEFORE YOU BEGIN
SCREW
COLLAR
RING (P)
CHAIN (S)
Carefully remove the fixture from the carton and check that all parts
are included, as shown in Figure 1. Be careful not to misplace any of
the screws or parts which are needed to install this fixture.
INSTALLATION
FIXTURE LOOP (H)
STEP 1:
Secure mounting bar (A) to outlet box with outlet box screws (not
supplied). Thread nut (B) onto nipple (C) so that three threads are
exposed over nut (B). Thread nipple (C) into mounting bar (A) and
secure with lockwasher and nut (B). Thread screw collar (D) to nipple
(C).
GLASS
RETAINING
SCREW (O)
ARMS (M)
SOCKET
CUP (I)
STEP 2:
GLASS
(R)
Using 2 pairs of pliers, open one link of chain (S) and connect it to
the fixture loop (H) at the top of the fixture. Slide screw collar ring (F)
and canopy (E) to fixture loop (H).
STEP 3:
Open one link on the other end of the chain (S) and attach it to the
screw collar (D). BE SURE TO CLOSE ALL CHAIN LINKS
COMPLETELY.
FIGURE 1
*NOT INCLUDED
INSTALLATION (continued)
HC-652
FINAL ASSEMBLY
Make sure no bare wires can be seen outside wire connectors.
STEP 4:
A. Take note of the color of the wire(s) on your fixture. Identify which
group your fixture wire(s) falls into and connect the wires according
to the directions below:
STEP 6:
After wires are connected, tuck them carefully inside outlet box.
Raise canopy (E) against ceiling and secure by threading screw collar
ring (F) to screw collar (D).
STEP 7:
Raise glass (R) onto socket cup (I) and secure in place by threading
glass retaining screws (O) to glass (R). Do not overtighten.
STEP 8:
Install lamps (not supplied).
GROUP A:
CONNECT TO BLACK HOUSE WIRE
GROUP B:
CONNECT TO WHITE HOUSE WIRE
BLACK
WHITE
*PARALLEL WIRE (ROUND & SMOOTH)
*PARALLEL WIRE (SQUARE & RIDGED)
*Note: When parallel wire is used, the tracer wire is square shaped or
ridged and less tracer wire is round in shape or smooth
(Seen best when viewed from wire end). To separate wires, grasp the
ends of each wire and pull apart.
B. Take your fixture wire(s) from group A and place evenly against
the black wire from the outlet box. DO NOT twist wires together
before using wire connectors.
C. Fit a wire connector (not supplied) over the wires and thread the
connector clockwise until you feel a firm resistance.
D. Gently try to remove the wires from the connector, If you can
remove the wires, carefully re-do steps B and C, as above and check
again for a firm connection.
E. Connect the fixture wire from group B to the white wire from the
outlet box in the same manner.
STEP 5:
GROUNDING INSTRUCTIONS: The green grounding screw (G) is to
be inserted into the hole with two raised dimples provided on the
mounting bar (A). Wrap the fixture ground wire (F) and the house
ground wire from the outlet box (bare metal or green insulated wire)
around the green grounding screw (G) on the mounting bar (A) and
tighten the green grounding screw (G) to secure.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
SUPPLY WIRES.
Download PDF