Installation And Safety Instructions HC-890 Line art shown may not exactly match the fixture enclosed. However, the installation instructions do apply to this fixture. Fill in Item Number on Carton and File This Sheet For Future Reference. ITEM#_______________ FOR YOUR SAFETY 042705 ASSEMBLY WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE WORKING ON IS SHUT OFF. EITHER THE FUSE REMOVED OR THE CIRCUIT BREAKER OFF. Carefully remove the fixture from the carton and check that all parts are included, as shown in Figure 1 & 2. Be careful not to misplace any of the screws or parts which are needed to install this fixture. GENERAL You don’t need special tools to install this fixture. Be sure to follow the steps in the order given. Read instructions carefully. If you are unclear as to how to proceed, consult a qualified electrician. STEP 1: Rotate arms (X) (if applicable). STEP 2: WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL INJURY, MOUNT TO OUTLET BOX OR SUPPORTING SYSTEM ABLE TO SUPPORT THE WEIGHT OF THE FIXTURE. *OUTLET BOX Install top break (M) (if applicable). GROUNDING AND MOUNTING BAR LOCK UP *OUTLET BOX *GROUND WIRE *WIRE CONNECTORS *WIRE CONNECTORS *GROUND WIRE MOUNTING BAR (A) *OUTLET BOX SCREWS MOUNTING BAR (A) *OUTLET BOX SCREWS GROUND WIRE (F) SCREW COLLAR (E) GREEN GROUNDING SCREW (D) CANOPY (H) SCREW COLLAR RING (G) CHAIN (S) FIXTURE LOOP (I) TOP BREAK (M) GLASS (J) ARM (X) *NOT SUPPLIED FIGURE 1 FIGURE 2 *NOT INCLUDED NUT (B) NIPPLE (C) INSTALLATION HC-890 IMPORTANT: DO NOT ATTACH FIXTURE DIRECTLY TO OUTLET BOX. STEP 1: Secure mounting bar (A) to outlet box with outlet box screws (not supplied). Thread nut (B) on nipple (C) so that 3 threads are exposed above nut (B). Thread nipple (C) into mounting bar (A) and secure with nut (B). Attach screw collar (E) to nipple (C). STEP 2: Using 2 pairs of pliers, open one link of chain (S) and connect it to the fixture loop (I) at the top of the fixture. STEP 3: Slide the screw collar ring (G) and canopy (H), in that order, over chain (S). Open one link on the other end of the chain (S) and attach it to the screw collar (E) which has been mounted to the ceiling nipple (C). BE SURE TO CLOSE ALL CHAIN LINKS COMPLETELY. STEP 4: Lace wires up through chain (S) and pass wires through holes in screw collar (E). We recommend lacing wire up through every other link of chain (S). C. Fit a wire connector (not supplied) over the wires and screw the connector clockwise until you feel a firmness. D. Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps B and C, as above and check again for a firm connection. E. Connect the fixture wire from group B to the white wire from the outlet box in the same manner. STEP 6: GROUNDING INSTRUCTIONS: The green grounding screw (D) is to be inserted into the hole with two raised dimples provided on the mounting bar (A). Wrap the ground wire (F) from the fixture (if supplied) and the ground wire from the outlet box (bare metal or green insulated wire) around the green grounding screw (D) on the mounting bar (A) if uninsulated wire is on the mounting bar (A), connect the ground wire (F) from the fixture (if supplied) and the outlet box to it using a small wire connector (not supplied). NOTE: Underwriters Laboratories does not require all fixtures to have ground wires. These fixtures still meet all UL specifications. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES. FINAL ASSEMBLY Make sure no bare wires can be seen outside wire connectors. STEP 1: STEP 5: A. Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below: After wires are connected, tuck them carefully inside outlet box. Raise canopy (H) against ceiling and screw the screw collar ring (G) to the screw collar (E). STEP 2: Place glass (J) over socket assembly. STEP 3: Install lamps. CLEANING To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper. GROUP A: CONNECT TO BLACK HOUSE WIRE GROUP B: CONNECT TO WHITE HOUSE WIRE BLACK WHITE *PARALLEL WIRE (ROUND & SMOOTH) *PARALLEL WIRE (SQUARE & RIDGED) *Note: When parallel wire is used, the tracer wire is square shaped or ridged and less tracer wire is round in shape or smooth. (Seen best when viewed from wire end.) To separate wires, grasp the ends of each wire and pull apart. B. Take your fixture wire(s) from group A and place evenly against the black wire from the outlet box. DO NOT twist wires together before using wire connectors. ORDERING PARTS Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from place of purchase. Be sure to use exact wording from illustration when ordering parts.