Hunter | 99111 | Use and Care Manual | Hunter 99111 Use and Care Manual

PACKAGE CONTENTS
Item #000-000
Model #99111
NOTE: Parts not shown to actual size.
USE AND CARE GUIDE
E
CR 2032
UNIVERSAL CEILING FAN WALL CONTROL
Part
Warranty
B
A
Description
D
C
F
Quantity
A
Receiver
1
B
Wall Control
1
C
Battery
1
D
Wire Connectors
7
E
Long Fasteners
2
F
Short Fasteners
2
Installation
Installation
1
5
Removing the canopy
WHAT IS NOT COVERED
This warranty excludes malfunctions or failures which were caused by repairs by persons not
authorized by us, mishandling, improper installation, modifications, or damage to the wall control
while in your possession, or unreasonable use. This warranty does not apply to batteries or to
deterioration or damage to the product caused by the use of faulty batteries. In no event shall
the manufacturer be liable for consequential or incidental damages. Some states do not allow
limitations on how long an implied warranty lasts or the exclusion or limitations of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other rights which vary from state to state.
Questions, problems, missing parts? Before returning to the store,
call Customer Service
9 a.m.-5:30 p.m., EST, Monday-Friday
1-888-830-1326
WWW.HOMEDEPOT.COM
Pre-Installation
TOOLS REQUIRED
Canopy
□□ Install the cover plate using a Phillips Head screwdriver to secure the two cover plate
screws. Figure D.
□□ Remove the wire connectors that connect the wires from the
outlet box to the fan, leaving the grounding wires connected.
Installing the receiver
A
Pliers
Flat Blade
Screwdriver
Phillips
Screwdriver
B
□□ You may have installation issues if the fan is installed on an angled ceiling.
NOTE: Some fans may have considerable excess lead wire. For easier receiver (A)
installation, cut the excess wire, leaving a minimum of 8 in. remaining. Re-strip the fan lead
wires 1/2 in., and place the remaining excess wire into the ceiling electrical box. The bracket
and fan must remain properly grounded.
6
Cable Tie
Receiver
Receiver
CAUTION: To avoid possible electrical shock, before installing or servicing your fan, disconnect the power
by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the
circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service
panel.
OR
Ceiling
Bracket
Ceiling
Plate
OR
Receiver
OR
A
Fan Body
Canopy
Canopy
Canopy
CAUTION: All wiring must be in accordance with national and local electrical codes. ANSI/NFPA 70. If you
are unfamiliar with wiring, use a qualified electrician.
NOTE: This product conforms to UL Standard 507.
3
Wiring the receiver to the fan
□□ Using the orange wire connectors (D), connect the yellow wire from the receiver (A) to the
black wire from the fan. Connect the blue wire from the receiver (A) to the blue wire (or
possibly black with white stripe wire) from the fan.
NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
D
RECEIV
OM
ER
FR
□□ Before operating the wall control (B),
press the battery door to eject it. Using
a Phillips head screwdriver, remove the
battery holder. Install the battery (C)
with the positive (+) side facing
downward.
□□ Secure the battery (C) by reinstalling
the battery holder. Finally, reinstall
the battery door into the wall control
(B). When necessary, replace the used
battery (C) with a CR2032 battery.
blue
Problem
Solution
The fan remote control is operating
inconsistently.
Install a fresh battery. Make sure the battery is installed
correctly.
The CFL bulbs flicker.
Turn the light switch off and back on. Within three
minutes, hold down the Fan Off button while pressing the
Light button twice. If the problem is not corrected, repeat
the process up to three times.
Battery
Holder
M FAN
FRO
D
yellow
black
A
A
Battery
□□ Turn on the power.
□□ Within three minutes of restoring power to
the fan, press both the Fan Off button and
the High button for at least four seconds.
The wall control (B) is now paired to the
fan’s receiver (A).
NOTE: If using the wall control with multiple
fans, repeat this process for each fan.
C
High
B
Using the wall control
ooo
High
Medium
oo
black (ungrounded)
OM CEILING
FR
B
white (grounded)
2
Using the Safe Exit program
NOTE: The Safe Exit program gives you about
thirty seconds of light, when you turn the lights
off, to exit the room before the lights go out.
Light
Fan
Off
white
Fan Off
□□ Hold the Fan Off button for at least three
seconds to initiate the Safe Exit program.
The lights will stay on 50% brightness for
15 seconds and then begin to dim. After
a total of 30 seconds, the lights will be
completely off.
Low
o
D
white
NOTE: The wall control (B) must be paired
before the fan will operate.
B
□□ To turn the fan on, press one of the fan
speed buttons. They are located next to
the Fan Off button.
□□ After all wires are connected and secured with wire connectors (D), re-install the canopy.
black
Pairing the wall control and receiver
Operation
Wiring the receiver and fan to the ceiling
RECEIV
OM
ER
FR
7
Battery
Door
1
4
B
B
blue
□□ Using the orange wire connectors (D), connect the black wire (ungrounded) from the ceiling
to the black wire from the receiver (A). Connect the white wire (grounded) from the ceiling to
both the white wire from the receiver (A) and the white wire from the fan.
Troubleshooting
C
B
Installing the battery
NOTE: If you are uncertain about wire colors or connections, please contact a qualified
electrician.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Reorient or relocate the receiving antenna,
increase the separation between the equipment and receiver, connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV
technician for help. Any changes or modifications to the remote control or receiver not expressly approved by
the manufacturer may void one’s authority to operate this remote control.
B
□□ Choose the hanging system that most closely resembles the one used by your fan and install
the receiver (A) and wire as directed.
M FAN
FRO
Ladder
□□ Insert the wall control (B) into the outlet box, and secure the two screws using a Phillips
head screwdriver. Figure C.
Safety Information
Care and Cleaning
To clean, use soft brushes or cloths to prevent scratching. Cleaning products may damage
finishes.
□□ Using the orange wire connectors (D), connect the two black wires (ungrounded) from the
outlet box. Connect the two green or bare wires (grounding) from the outlet box with the
grounding wire from the wall control (B). Figure B.
□□ Remove the canopy by following the instructions supplied by
the fan manufacturer.
1-YEAR LIMITED WARRANTY
WHAT IS COVERED
The manufacturer makes the following limited warranty to the original purchaser of the wall
control: Your wall control is warranted to be free from defects in material and workmanship for
a period of one year from the date of sale. If the wall control malfunctions or fails within the
warranty period due to a defect in material or workmanship we will replace it free of charge. If
the original purchaser ceases to own the wall control, this warranty and any implied warranty,
including but not limited to any implied warranty of merchantability or fitness for a particular
purpose, are voided. This warranty is in lieu of all other express warranties. The duration of any
implied warranty, including, but not limited to, any implied warranty of merchantability or fitness
for a particular purpose, in respect to any control, is expressly limited to the period of the express
warranty set forth above for such control.
□□ Remove the switch plate cover and all wiring from the switch. Figure A.
NOTE: If you are uncertain about wire colors or
connections, please contact a qualified electrician.
□□ Before installation, use the pull chains to set the fan speed
to HIGH and the light to ON. Ensure the power is off before
proceding.
2
Installing the wall control
NOTE: For CFL lighting, the lights will stay on
100% brightness for 30 seconds. After a total of
30 seconds, the lights will be completely off.
Download PDF