Hunter | 59136 | Use and Care Manual | Hunter 59136 Use and Care Manual

www.HunterFan.com
Table of Contents
Congratulations on purchasing your new
Hunter® ceiling fan! It will provide comfort
and performance in your home or office for
many years. This installation and operation
manual contains complete instructions for
installing and operating your fan.
Tools Needed
Mounting Options
Ceiling Bracket
30 inches
4
Wiring
Canopy
5
11
PA G E
3
PA G E
Downrod
Ladder
PA G E
2
PA G E
7 feet
PA G E
We are proud of our work and appreciate
the opportunity to supply you with the best
ceiling fan available anywhere in the world.
What to Expect with
Your Installation
1.888.830.1326
Finial
To register your fan, please visit:
www.HunterFan.com/register
Save your receipt for proof of purchase.
Operation, Maintenance
& Cleaning
Wall Control
Troubleshooting
?
?
?
17
PA G E
16
PA G E
1
M3572-01 • 12/01/14 • © Hunter Fan Company
14
PA G E
PA G E
12
10
PA G E
Blades
PA G E
9
PA G E
6
www.HunterFan.com
What to Expect with Your Installation
Read and Save These Instructions
If you are unfamiliar
with wiring, use a
qualified electrician.
This product conforms to UL Standard 507.
WARNINGS
30 inches
from blade tip
to nearest wall
or obstruction
Must be able to
secure the fan to
building structure or
fan-rated outlet box
7 feet
from bottom
edge of blade
to the floor
Know your wiring
Assess location
w.1 - To reduce the risk of fire, electrical shock, or
personal injury, mount fan directly from building
structure and/or an outlet box marked acceptable for
fan support of 70 lbs (31.8 kg) and use the mounting
screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing
or servicing your fan, disconnect the power by turning
off the circuit breakers to the outlet box and associated
wall switch location. If you cannot lock the circuit
breakers in the off position, securely fasten a prominent
warning device, such as a tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor
damage, use only Hunter Solid State Speed Controls.
You may need a
friend to help you.
w.4 - To reduce the risk of personal injury, do not bend the
blade brackets when installing the blade brackets, balancing
the blades, or cleaning the fan. Do not insert foreign objects
in between rotating fan blades.
Ceiling angles greater
than 34° will require an
Angled Mounting Kit.
See page 4 for details.
Check box to see
fan weight
1.888.830.1326
CAUTIONS
c.1 - All wiring must be in accordance with national and
local electrical codes ANSI/NFPA 70. If you are unfamiliar
with wiring, use a qualified electrician.
c.2 - Use only Hunter replacement parts.
Assess ceiling angle
2
M3572-01 • 12/01/14 • © Hunter Fan Company
www.HunterFan.com
Tools Needed
Ladder
Pliers
Wire Strippers
9/64” Drill Bit
(optional)
Power Drill
(optional)
If mounting to a support structure, you will also need these tools.
3
M3572-01 • 12/01/14 • © Hunter Fan Company
Screwdrivers
1.888.830.1326
34O
CEILING
www.HunterFan.com
Mounting Options
OPTION 1
If you have a flat ceiling:
1. If your ceiling angle is less than 34°, hang your fan
by the standard downrod (included).
2. If your ceiling angle is greater than 34°, you will
also need an Angled Mounting Kit (sold separately).
Angled
Mounting
Support
Structure
Support
Structure
OPTION 2
If you have an angled ceiling:
Standard
Mounting
Style
Ceiling
Outlet Box
(required)
Use the three steps below to determine if your ceiling angle is greater than 34°
2
1
Ceiling
Outlet Box
(required)
Angled
Mounting
Style
3
34°
PLACE
FOLD
against wall
on dotted line
Guide Touches
BOTH Ceiling & Wall
Follow the
instructions in
this manual.
*most common
SLIDE
toward ceiling
Guide Touches Wall
but NOT Ceiling
2
ON
SITUAT
I
1
ON
SITUAT
I
WALL
Standard
Mounting
Hang your fan by the standard downrod (included).
1.888.830.1326
1.866.268.1936
Use Standard Mounting
to hang the fan from a flat ceiling.
You need an
Angled
Mounting Kit.
4
M3572-01 • 12/01/14 • © Hunter Fan Company
Use Angled Mounting
to hang the fan from a
vaulted or angled ceiling.
Ceiling Bracket
www.HunterFan.com
1.888.830.1326
r
we
o
nP
r
Tu
OFF
For angled ceilings, point
opening toward peak.
Use wood screws
Use machine screws
(included) when securing
(provided with outlet
to support structure with
box) when securing to
approved electrical outlet existing ceiling fan-rated
box. Drill 9/64” pilot holes
outlet box. Make sure
in support structure to aid
it is securely installed
in securing ceiling bracket and is acceptable for fan
with hardware found in support of 31.8 kg (70 lbs)
the
hardware bag.
or less.
Make sure all four bumpers are
still attached.
If you are unable to do this,
call Technical Support at
1-888-830-1326.
Refer to warning w.1 on pg. 2
5
M3572-01 • 12/01/14 • © Hunter Fan Company
To avoid possible electrical shock, before
installing your fan, disconnect the power by
turning off the circuit breakers to the outlet
box associated with the wall switch location.
www.HunterFan.com
1.888.830.1326
skip to next page
Standard
Downrod
Steps 1-5 to remove standard downrod pipe
Longer
Downrod
2
3
4
10
9
8
Steps 6-10 to reassemble with new pipe
6
M3572-01 • 12/01/14 • © Hunter Fan Company
5
Slide
Slide
1
Sold Separately
Option 2
If you need a different downrod length follow these steps:
Included
(pre-assembled)
Option 1
Downrod
7
6
www.HunterFan.com
CUT
Tip: If you have
difficulty feeding the
wires through the
downrod, try taping the
wires to a thin dowel
rod, then drop the dowel
rod and wires through
the downrod. Be sure to
remove all tape once the
wires are fed through to
the other side.
KEEP!
(not to scale)
8”
&
3/8”
1.888.830.1326
STRIP
Downrod (continued)
!
KEEP
Remove the pre-installed
setscrew so that the downrod
can be inserted.
The wires can be cut, but
leave at least 8” extending
from the top of the downrod.
Hand tighten the downrod (at
least 4-5 full turns) until it stops.
8”
Tighten the setscrew
with pliers. DO NOT
HAND TIGHTEN.
3/8”
If the setscrew is not tightened
securely, the fan may fall.
7
M3572-01 • 12/01/14 • © Hunter Fan Company
www.HunterFan.com
Downrod (continued)
Put the wires and downrod through the
canopy. Let the canopy sit loosely on top
of the fan.
DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod
ball into the slot in the ceiling bracket.
8
M3572-01 • 12/01/14 • © Hunter Fan Company
1.888.830.1326
Wiring
OM
FR
CEILIN
Note: To connect the wires, hold the bare metal
leads together and place a wire connector over
them, then twist clockwise until tight.
G
Green/Yellow
Stripe
1.888.830.1326
G
Using the orange wire
connectors from
the
hardware bag, connect
the black wire (ungrounded)
from the ceiling to the black
wire from the fan. Connect
the white wire (grounded)
from the ceiling to the white
wire from the fan.
T
Black
CEIL
KE
M
White
Green/Yellow
Stripe
FR
O
CEILIN
(Ungrounded)
OM FAN
FR
OM
FR
(Grounded)
(Grounding)
Using an orange wire
connector from
the
hardware bag,
connect the 3 grounding
wires (green, green/
yellow stripe, or bare
copper) coming from the
ceiling, downrod, and
hanging bracket.
www.HunterFan.com
ING BR
AC
FRO
M FA N
Turn the splices upward and push them carefully back through the hanger bracket
into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
Refer to CAUTION c.1 on pg. 2
9
M3572-01 • 12/01/14 • © Hunter Fan Company
www.HunterFan.com
Canopy
Screw
Holes
Position the canopy so that, when
lifted into place, the canopy fits into
the hanging bracket as shown.
Lift the canopy into place so that
the screw holes are aligned.
Insert the two canopy screws
found in the
hardware bag.
Note: Fan style may vary.
10
M3572-01 • 12/01/14 • © Hunter Fan Company
1.888.830.1326
Finial
www.HunterFan.com
Screw the finial onto the threaded rod found at
the bottom of the motor assembly.
11
M3572-01 • 12/01/14 • © Hunter Fan Company
1.888.830.1326
Blades
www.HunterFan.com
1.888.830.1326
Screw
Holes
Lift a blade ring to the motor assembly
and align the screw holes.
Install three blade assembly screws,
found in the
hardware bag.
If you wish to install your fan with
three blades, skip to the next page.
Note: In order to provide proper blade
support, choose the three small screw holes
that are aligned with the three arms of the
blade ring as shown in the illustration.
If you wish to install your fan with
six blades, lift the optional second
blade ring to the motor assembly
and install three blade assembly
screws (found in the
hardware
bag) as shown in the illustration.
12
M3572-01 • 12/01/14 • © Hunter Fan Company
Blades (continued)
www.HunterFan.com
Your blades are shielded with Dust Armor®
which is a nanotechnology coating that repels
dust. For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning agents
may damage the finishes.
Attach each blade to the blade ring using
three blade assembly screws, found in
the
hardware bag.
13
M3572-01 • 12/01/14 • © Hunter Fan Company
1.888.830.1326
www.HunterFan.com
Wall Control
1.
1.
2.
Shut off power to the room you will
be working in at the breaker box.
After removing the switch plate cover,
remove all wiring from the switch.
1.888.830.1326
1.
2.
Using the wire connectors, connect each
black wire from the wall control to a
black wire from the switch box.
Note: If two white wires are present in
the switch box, connect them to each
other if they are not already connected.
Do not restore power until all work is complete.
14
M3572-01 • 12/01/14 • © Hunter Fan Company
2.
Insert the wall control into the
outlet box and secure the two metal
tabs to the tabs on the switch box
using the two flat head screws that
came with the switch box.
www.HunterFan.com
Wall Control (continued)
1.
CONGRA
T
YOU’REUALTIONS!
DONE!
2.
Remove the knob from the wall
control and mount the faceplate
(not included) to the wall control
using the two #6-32 screws you
removed earlier from the faceplate.
Reattach the knob onto the wall
control and turn it to the left for the
OFF position.
15
M3572-01 • 12/01/14 • © Hunter Fan Company
1.888.830.1326
www.HunterFan.com
Operation, Maintenance & Cleaning
1.888.830.1326
Reverse
Switch
r
we
o
nP
r
Tu
ON
The knob on the wall control unit
controls power to the fan. The fan has
four speed settings in sequence:
high, medium, low and off.
To change the direction of air flow,
move the reverse switch to the
opposite position.
16
M3572-01 • 12/01/14 • © Hunter Fan Company
For cleaning the fan, use soft brushes or
cloths to prevent scratching. Cleaning
products may damage the finishes.
www.HunterFan.com
Troubleshooting
Fan doesn’t work
Excessive wobbling
• Make sure power switch is on.
• Tighten all of the blade and
blade ring screws until they
are snug.
• Push the motor reversing switch
firmly left or right to ensure that
it is engaged.
• Check the circuit breaker to
ensure the power is turned on.
Hunter fans have the power to cut your cooling costs up
to 40%.
Beat the High Cost of Cooling
The air movement created by a Hunter ceiling fan
lets you set your thermostat higher and still stay
comfortable. Every degree you raise the thermostat
saves up to 7% on energy costs. So, you can cut back on
expensive air conditioning ... and save up to 40%* on
cooling. In winter, your Hunter fan recirculates warm air
and saves up to 10%* on heating bills.
* On average at low speed settings. Your savings may
vary based on climate, building type and thermostat
setting.
Save Energy and Money While Protecting
the Environment
Congratulations! You’re saving energy and money while
protecting the environment by purchasing this ENERGY
STAR qualified Hunter ceiling fan! With this purchase, you
are doing your part to protect the environment.
Your new ceiling fan has earned the ENERGY STAR label
because it meets high energy efficiency specifications
set by the Environmental Protection Agency (EPA).
ENERGY STAR labeled ceiling fans save energy because
they have more efficient fan motors and air delivery due
to more aerodynamic blade configurations. Ceiling fan
models bearing the ENERGY STAR label move air 14 20% more efficiently than typical ceiling fan models.
For more information on ENERGY STAR visit www.
energystar.gov.
• Turn the power off, support
the fan carefully, and check
that the hanger ball is
properly seated.
• Make sure the blades spin freely.
• Turn off power from the circuit
breaker, then loosen the canopy
and check all the connections
according to the wiring diagram
on page 9.
• Turn off power from the circuit
breaker, then ensure the wall
control is properly installed
according to the instructions on
pages 14-15.
1.888.830.1326
Noisy Operation
• Tighten the blade and blade
ring screws until they are snug.
• Check to see if any of the
blades are cracked. If so, replace
all of the blades.
17
M3572-01 • 12/01/14 • © Hunter Fan Company
Download PDF