Global Direct | 21094 | Installation guide | Global Direct 21094 Installation Guide

A
B
A
A
B
B
A
A
A
B
B
B
A
B
C
A
A
A
C
B
B
C
A
A
CSA010011HAUT1
INSTALLATION INSTRUCTIONS
.
PLEASE READ CAREFULLY AND SAVE THESE
INSTRUCTIONS, AS YOU MAY NEED THEM AT A LATER
DATE.
CAUTION – Turn off the main power at the circuit breaker before
installing the fixture, in order to prevent possible shock.
1.OUTLET BOX
2.MOUNTING BRACKET
3.#8-32 HEX NUT
4.FIXTURE MOUNTING SCREW
5.WHITE TO WHITE WIRE CONNECTION
6.BLACK TO BLACK WIRE CONNECTION
7.POWER SUPPLY GROUND WIRE
8.FIXTURE GROUND WIRE
9.GROUND SCREW
10.MOUNTIN SCREW
11.CANOPY
12.DECORATIVE NUT
Remove the fixture and the mounting package from the box and
make sure that no parts are missing by referencing the
illustrations on the installation instructions.
FOR CEILING MOUNT (Fig. 4 & 5)
1.A) Place the #8-32 HEX NUTS (3.) onto the #8-32 FIXTRUE MOUNTING SCREWS (4.),
and attach the FIXTURE MOUNTING SCREWS to the MOUNTING BRACKET (2.), or
universal mounting plate (whichever is provided). Do not tighten the HEX NUTS at this time.
(Fig.4)
B) If the fixture uses a single 1/8” IPS NIPPLE (4.) for mounting, thread the 1/8” IPS HEX
NUT (3.) onto the NIPPLE, and screw the NIPPLE into the MOUNTING BRACKET (2.),
without tightening the HEX NUT. (Fig.5)
2.Pull the power supply wires out from the OUTLET BOX (1.), and mount the MOUNTING
BRACKET (2.) or the universal mounting plate to the OUTLET BOX, using MOUNTING
SCREWS (10.)
3. Attach the power supply wires to the fixture lead wires by connecting BLACK to BLACK
(or SMOOTH), and WHITE to WHITE (or RIBBED). Attach the POWER SUPPLY
GROUND WIRE (7.) from the OUTLET BOX (1.), and the FIXTURE GROUND WIRE (8.)
from the fixture to the green GROUND SCREW (9.) on the MOUNTING BRACKET (2.), or,
connect both wires together using the correct size of wire connectors.
4.Place the CANOPY (11.) on the fixture over the OUTLET BOX (1.) and onto the fixture
mounting screws [or NIPPLE (4.)], and adjust the #8-32 fixture mounting screws (or
NIPPLE ) until they protrude out from the CANOPY 1/4”. Remove the CANOPY and secure
the position of the fixture mounting screws (or NIPPLE) by tightening the HEX NUT (S) (3.)
against the MOUNTING BRACKET (2.). Place the CANOPY back onto the fixture mounting
screws, (or NIPPLE), and secure into place using the DECORATIVE NUTS (12.) provided.
1.OUTLET BOX
2.MOUNTING BRACKET
3.1/8” IPS HEX NUT
4.NIPPLE
5.WHITE TO WHITE WIRE CONNECTION
6.BLACK TO BLACK WIRE CONNECTION
7.POWER SUPPLY GROUND WIRE
8.FIXTURE GROUND WIRE
9.GROUND SCREW
10.MOUNTIN SCREW
11.CANOPY
12.DECORATIVE NUT
5.Screw in light bulbs that do not exceed the maximum wattage specified on the fixture’s
wattage rating label, into the socket(s) on the fixture.
INSTALLATION COMPLETED
FOR CHAIN-SUSPENDED CEILING MOUNT (Fig. 6)
1.Screw the 1/8” IPS HEX NUTS (5.) onto the 1/8” IPS NIPPLE (4.), and then attach the
end of the NIPPLE that has the HEX NUT to the MOUNTING BRACKET (2.). Do not
tighten the HEX NUT. Pull the SUPPLY GROUND WIRES (8.) out from the OUTLET BOX
(1.), and attach the MOUNTING BRACKET (2.) assembly to the OUTLET BOX, by using
the slotted holes on the MOUNTING BRACKET and the MOUNTING SCREWS (3.)
provided.
2.Thread a 1/8” IPS HEX NUT (5.), and the SCREW COLLAR LOOP (6.) onto the NIPPLE
(4.) end that is facing down, but do not tighten the HEX NUT. Place the CANOPY (15.) over
the OUTLET BOX (1.) and adjust the SCREW COLLAR LOOP and NIPPLE until the
outside threads on the SCREW COLLAR LOOP is centered with the center hole opening of
the CANOPY. Take away the CANOPY and tighten the HEX NUTS down on the
MOUNTING BRACKET (2.), and the SCREW COLLAR LOOP.
3.Open up the end links of the CHAIN (17.) and attach one end of the CHAIN onto the
FIXTURE LOOP (18.). Slide the THREADED RING (16.) from the SCREW COLLAR LOOP
(6.), and the CANOPY (15.) onto the CHAIN in that order, and attach the other end of the
CHAIN on to the SCREW COLLAR LOOP. Close the ends of the chain links.
4.Unravel the fixture’s lead and ground wires and thread the lead and ground wires through
every other link of the CHAIN (17.), and out through the SCREW COLLAR LOOP (6.) and
NIPPLE (4.) assembly, starting with the chain link attached to the FIXTURE’S LOOP (18.).
5.Attach the power supply wires to the fixture lead wires by connecting the BLACK
POWER SUPPLY WIRE (11.) to the SMOOTH FIXTURE LEAD WIRE (12.), and the
WHITE POWER SUPPLY WIRE (9.) to the RIBBED FIXTURE LEAD WIRE (10.). Attach
the SUPPLY GROUND WIRE (8.) from the OUTLET BOX (1.), and the FIXTURE
GROUND WIRE (7.) from the fixture onto the green GROUND SCREW (14.) on the
MOUNTING BRACKET (2.), or, connect both wires together using the correct size of WIRE
CONNECTORS (13.). Place connected wires inside of the OUTLET BOX.
6.Slide the CANOPY (15.) and the THREADED RING (16.) of the SCREW COLLAR LOOP
(6.) up the CHAIN (17.). Place the CANOPY over the OUTLET BOX (1.), and secure in
place by screwing the THREADED RING onto the SCREW COLLAR LOOP.
7.Screw in light bulbs that do not exceed the maximum wattage specified on the fixture’s
wattage rating label, into the socket(s) on the fixture.
NOTE: If the bottom opening of the lamp compartment to the fixture is too narrow to allow
access to the light bulb(s), unscrew the two decorative screws at the top of the lamp
compartment to allow it to drop down for lamp replacement.
INSTALLATION COMPLETED
CST001
1.OUTLET BOX
2.MOUNTING BRACKET
3.MOUNTING SCREW
4.NIPPLE
5.1/8” IPS HEX NUT
6.SCREW COLLAR LOOP
7.FIXTURE GROUND WIRE
8.SUPPLY GROUND WIRE
9.WHITE SUPPLY WIRE
10.RIBBED FIXTURE LEAD WIRE
11.BLACK SUPPLY WIRE
12.SMOOTH FIXTURE LEAD WIRE
13.WIRE CONNECTOR
14.GROUND SCREW
15.CANOPY
16.THREADED RING
17.CHAIN
18.FIXTURE LOOP
Download PDF