Advertisement
Advertisement
SERIES [e 8000 LED TV user manual Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung .com/register Model _ _ _ _ _ Serial No. _ _ __ _ ~ If you have any questions, please call us at 1-800-SAMSUNG (1-800-726-7864) for assistance. Important Safety Instructions This symbol indicates that high voltage is present ins1de. It is dangerous to make any kind of contact with any internal part of this product. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL. This symbol indicates that important literature concerning operation and maintenance has been included with this product. • The slots and openings in the cabinet and in the back or bottom are provided for necessary ventilation. To ensure reliable operation of th1s apparatus, and to protect it from overheating, these slots and openings must never be blocked or covered. - Do not place th is apparatus in a confined space, such as a bookcase, or built-in cabinet, unless proper ventilation is provided. - Do not place th is apparatus near or over a radiator or heat register, or where it is exposed to direct sunlight. - Do not place vessels (vases etc.) conta1ning water on this apparatus, as this can result in a fire or electric shock. • Do not expose this apparatus to rain or place it near water (near a bathtub, washbowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool etc.). If this apparatus accidentally gets wet, unplug it and contact an authorized dealer immediately. • This apparatus uses batteries. In your community, there might be environmental regulations that require you to dispose of these batteries properly. Please contact your local authorities for disposal or recycling information. • Do not overload wall outlets, extension cords or adaptors beyond their capacity, since this can result in fire or electric shock. • Power-supply cords should be placed so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords at the plug end, at wall outlets, and the point where they exit from the appliance. • To protect this apparatus from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the set due to lightning and power line surges. • Before connecting the AC power cord to the DC adaptor outlet, make sure the voltage designation of the DC adaptor corresponds to the local electrical supply. • Never insert anything metallic into the open parts of this apparatus. Doing so may create a danger of electric shock. • To avoid electnc shock, never touch the inside of this apparatus. Only a qualified technician should open this apparatus. • Make sure to plug the power cord in until 1t IS f1rmly seated. When unplugging the power cord from a wall outlet, always pull on the power cord's plug. Never unplug by pulling on the power cord. Do not touch the power cord with wet hands. • If this apparatus does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service center. • Be sure to pull the power plug out of the outlet if the TV is to remain unused or if you are to leave the house for an extended period of time (especially when children, elderly or disabled people will be left alone in the house). - Accumulated dust can cause an electric shock, an electric leakage or a fire by causing the power cord to generate sparks and heat or the insulation to deteriorate. • Be sure to contact an authorized service center for information if you intend to install your TV in a location with heavy dust, high or low temperatures, high humidity, chemical substances, or where it will operate 24 hours a day such in an airport, a train station, etc. Failing to do so may lead to serious damage of your TV. • Use only a properly grounded plug and wall outlet. - An improper ground may cause electric shock or equipment damage. (Class I Equipment only.) • To turn this apparatus off completely, you must disconnect it from the wall outlet. Consequently, the wall outlet and power plug must be readily accessible at all times. • Do not allow children to hang onto the product. • Store the accessories (battery, etc.) in a location safely out of the reach of children. • Do not install the product in an unstable location such as a shaky self, a slanted floor or a location exposed to vibration. • Do not drop or apply any shock to the product. If the product is damaged, disconnect the power cord and contact a service center. • To clean this apparatus, unplug the power cord from the wall outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air fresheners, lubricants, or detergent. These chemicals can damage the appearance of the TV or erase the printing on the product. • Do not expose this apparatus to dripping or splashing. • Do not dispose of batteries in fire. • Do not short-circuit, disassemble or overheat the batteries. • There is danger of an explosion if you replace the batteries used in the remote with the wrong type of battery. Replace only with the same or equivalent type. • WARNING - TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. Contents Basic Features 30 Basics 5 18 Using the Smart Touch Control 6 6 7 8 X lovv POW81' 3D Active Glasses 18 Pairing 3D Active Glasses 20 VJatching 3D Video to tr1e 21 What is Remote Support? Using the touchpad 8 8 8 8 SilO\f·.J and Troubleshooting and Other Information Reco:·r:r-ret-'IC1ed g Contr-c;l 10 Turning on the 1V 11 Built-in 1V Camera and Microphone 22 Troubleshooting 23 Mounting the 1V on the Wall Using the Wall Mount Kit (Optional) 11 Extending the TV Camera 11 Retracting the Camera 25 Assembling the Cable clip 25 Assembling the Screw Cover 12 Switching Between Video Sources 25 Assembling the Power inlet Cover 13 Universal Remote Control Setup 26 Eco Sensor and Screen Brightness 27 Maintenance 27 Providing Proper Ventilation for Your 1V 28 Securing the 1V to the Wall 13 Add 14 External Device Viewing the e-Manual 14 Scrolling a Page 14 Using the Top Icons. 14 Returning to Home Page 14 Searching the Index 15 Searching Pages 15 Closing the e-Manual 15 Jur11ping to a Menu Item 15 Updating the e-Manual Network Configuration 16 Connecting to a Network 16 Network Connection - VVireless 16 Wireless Network Precautions 16 Network Security Protocols 17 Network Connection - Wired Specifications 30 Specifications 32 Dimensions 32 Licenses Guides 33 Warranty Information 35 Regulatory Compliance Statements (For 3D Active Glasses) 36 SAMSUNG BRAND PRODUCTS 36 LIMITED VVARRANTY TO ORIGINAL PURCHASER Figures and illustrations in this User Manual are provided for reference only and may differ from the actual product appearance. Product design and specifications may change without notice. Features of your new TV • 30: This new feature enables you to view 30 content. • SMART HUB: This TV features Smart Hub, a multi-purpose entertainment and family center. With Smart Hub, you can surf the web, download applications, and stay in touch with family and friends through social networking services. In addition, you can view or play photo, video, and music files stored on external storage devices. Press t) to launch Smart Hub. Choose a service using the icons displayed in the top part of the screen. Smart Hub services and functionality include: Social: Watch the latest YouTube videos and your and your friends ' video posts on Facebook and Twitter. You can also make video calls to friends by connecting the TV to a camera. Apps: Samsung Apps offers an extensive collection of free and paid news, sports, weather, and gaming content you can directly download to and enjoy on your TV. On TV: Check a listing of programs that are currently airing or are scheduled to air. Movies & TV Shows: Purchase and watch movies and series without a separate external device. Photos, Videos & Music: Play back photo, video, and music files from an external storage device. • Anynet+ (HDMI-CEC): This allows you to control all connected Samsung devices that support Anynet + with your Samsung TV's remote. • e-Manual: Provides a detailed, on-screen user's manual built into your TV. • SMART Interaction: Using this function, you can access and control menu options and functions using motions. • Device Manager: Use the TV features with a USB or Bluetooth keyboard and mouse. • MHL & Screen Mirroring : Displays mobile device screens on your TV using a wired or wireless connection. Using the Smart Touch Control Use Voice Recognition function w i t h - - - - - - - - - - - - - , the microphone embedded in remote control. ~The Voice Recognition function ·can be affected by unclear pronunciation, voice level, or surrounding noise. MUTE Cuts _;,..._.,:...:::::: off the sound temporarily. . - - - - - - - - Turn on and off the satellite or cable set-top box connected to the TV. For this, the Smart Touch Control must be configured as a universal remote control. See the e-Manual chapter, Controlling the TV > Universal Remote Control Setup. ~~~~ =--- Displays a virtual remote control on the screen. See the e-Manual chapter, Controlling the TV > Virtual Remote Control. Adjusts the volume. LIGHT: Turn on the backlight for the buttons. The backlight lasts for only a few seconds. Turns the rernote control light on or off. When on, the buttons become illuminated for a moment when pressed. (Using the remote control with this button set to On will reduce the battery usage time.) OVR: Displays the STB EPG (Electronic Program Guide). MENU: Opens the OSD. 30: Turns the 3D function on or off. See e-Manual chapter, TV Viewing > 30 TV. =---- Touch Pad • Drag on the Touch Pad to move the focus on the screen. • Press the Touch Pad to run, activate, or select the highlighted item. • Press and hold the touch pad to display the Channel List. ---=••~-- Displays the EPG (Electronic Program Guide). =====:----- Brings up Smart Hub applications. See the e-Manual chapter, Smart TV Features > Smart Hub. ~To exit an application that is running easily, press the button. e Connecting to the TV In order to operate the TV using a Smart Touch Control, you must first pair it to the TV via Bluetooth . 1. To turn on the TV, point the Smart Touch Control at the remote control receiver of the TV and press the 0 button. The remote control receiver's location may vary depending on the model. 2. A Bluetooth icon will appear at the bottom left of the screen as shown below. The TV will then attempt to connect to the Smart Touch Control unit automatically. <Attempting to connect and completion icons> Inserting the Batteries (AAA X 2) 0 1. Gently pull on the battery cover's notch with a fingernail and then remove the cover completely once it comes loose. You can also use a thin coin. 2. Insert 2 AAA batteries, making sure to align the positive and negative ends correctly. 3. Align the battery cover with the back of the remote control, and then press down along the edges until it is completely attached to the remote control. Reconnecting the Smart Touch Control Unit If you need to reestablish the connection between the 1V and the Smart Touch Control, press the pairing button at the back of the Smart Touch Control, pointing at the remote control sensor of the 1V. <The Smart Touch Control unit's pairing button> The pairing button can be accessed by removing the control unit's battery cover. Pressing the pairing button automatically reestablishes the connection between the control unit and the 1V. Low Battery Power Warning If the battery becomes low while using the Smart Touch Control, the following alarm window appears at the bottom of the left screen. <Low battery alarm window> Using the touchpad Use the touchpad to implement various commands. Navigate to Tutorial (System > Device Manager > Smart Touch Control Settings > Tutorial) to view an on-screen guide to using the Smart Touch Control. Drag on the touchpad to move the focus, pointer, or highlight in the direction the finger is dragging. Tap on the touchpad to select the item highlighted or in focus. When watching 1V, pressing and holding the touchpad displays the channel list. On some apps, pressing and holding the touchpad for over 2 seconds displays a list of functions available for the app. Show Status and Notification Banner Press the MORE button on the Smart Touch Control and then select STATUS on the virtual control panel that appears on the screen. The status and alarm banner appears at the top of the screen. For more information about using the status and alarm banner, refer to e-Manual > Smart Features > Status and Notification. Recommended Press the RECOMM. I SEARCH button and then select the Recommended from the list on bottom of t he screen. The recommended programs from among the programs currently being broadcast as well as recommended applications are listed. If you select a program from the list, the corresponding channel is displayed and if you select an application, the application is launched. However, if the selected application is not installed on the TV, Samsung Apps is launched so that you can install the application on the TV. Refer to e-Manual > Smart TV Features > On TV for more information. History Tap on RECOMM. I SEARCH and then select History from the list displayed at the bottom of the screen. This displays an interactive list of recently accessed channels, media content and applications. Searching Press the RECOMM. I SEARCH button and select Search from the Recommended list. The keypad w ill appear on the screen . Enter search criteria to search not only many apps and their contents on the TV but also the Web. Refer to e-Manual > Smart Features > Searching for more information . Using the Virtual Remote Control Press the MORE button to display the virtual remote control on the 1V screen. The virtual remote control consists of the number panel , a playback control panel, and the quick access panel. Use the touchpad to highlight and select icons, numbers, and buttons on the panels. ~ The displayed virtual remote control on the TV screen may differ depending on the country. ( ) < >< > Changing the Virtual Remote Control Panel You can change which Virtual Remote Panel is displayed on the 1V screen, To shift between panels, move the focus highlight beyond the left or right edge of the displayed panel. Using the Number Panel Use the number panel to enter numbers on a keypad screen or webpage or to change the channel while watching 1V. Changing the channel using the number pad leaves a record, allowing you to easily return to previous channels. Using the Playback Control Panel Use the playback control panel to pause, rewind, fast forward, skip to the next file, select a function with the a, m, l!l, [!) buttons, and much more while enjoying media content. Using the Quick Access Panel Use the buttons on the quick access panel to bring up the 1V's MENU, INFO, ore-Manual screens. Note that the buttons that appear may vary depending on the operating mode of the Smart Touch Control (with the 1V only, as a universal remote, etc.). ----------------------------------------------------------------------------------- Turning on the 1V Turn on the 1V using the C) button on the remote control or 1V panel. ~ The first time you turn on your TV, it w ill immediately start the initial setup. ~ The product color and shape may vary depending on the model. ~ The TV's Controller, a small joy stick like button on the rear right side of the TV, lets you control the TV without the remote control. Camera Open Smart Hub. Select a source. Open the menu. Turn off the TV. i!:===;=:r=~;;;;;;====;;;;;;;;;~;;;;;;;;;'=i==~ .. -- -------- ---Tho";;,;,,;; ;,;ck·,; :;;~:'Jr~:-f lower-left corner on the back of the TV ; 'I ' . '--- - Remote control sensor When you use the Smart Touch Control, the standby LED does not respond, ___ ___ _ ~ ) ~~ wOOo ~coc= the 0 ; :/ ·._(! ____. b" llw ' r-iSl + · C) : - , ., .. " . v : ' 1 ' ' ',---- ---- - - ·' Built-in TV Camera and Microphone This 1V features a built-in 1V camera and microphone that you can use for the Motion Control, Voice Recognition, and Face Recognition features. You can also use the camera's angle adjustment knob to change the camera's viewing angle. Microphone Knob for camera's angle adjustment I ---- LJ) ;---- r [Jj Lens ® ~ ( _\ - 7 --- Microphone & Do not touc h the lens while operating the 1V camera. You can leave fingerprints that may affect the image quality. If the lens gets dirty, clean it using a soft piece of cloth. / Extending the TV Camera To use the 1V camera, you must first extend it. Gently push the camera in without touching the lens until you hear a click. The camera pops up. Retracting the Camera If you are not using the 1V camera, keep it retracted inside the 1V. The Motion Control and Face Recognition features cannot be used while the 1V camera is in the retracted state, but Voice Recognition will still be available. Gently push the camera in without touching the lens until you hear a click. Switching Between Video Sources Press the SOURCE button to switch between devices connected to the 1V. For example, to switch to a game console connected to the second HDMI connector, press SOURCE button . From the Source list, select HDMI2. The connector names may vary depending on the product. Select Tools at the upper-right corner of the source screen to access the following functions. • Edit Name: Lets you associate a device name to an input source. You can select the following device names in the Edit Name option: VCR I DVD I Cable STB I Satellite STB I PVR STB I AV Receiver I Game I Camcorder I PC I DVI PC I DVI Devices I TV I IPTV I Blu-ray I HD DVD I DMA To associate a device name to an input source, follow these steps: 1. Select Tools in the upper right corner of the source screen. 2. Select Edit Name. 3. Find the input source you want in the Source list (HDMI1, HDMI2, Component, etc.). 4. Select the blank field next to the input. 5. In the device name list that appears, select the name of the device attached to the input. When you view the Source list, the device name and the input jack will be displayed together. - If you have connected a PC to the HDMIIN 2 (DVI) port with an HDMI cable, select PC from the device name list. - If you have connected a PC to the HDMIIN 2 (DVI) port with an HDMI to DVI cable, select DVI PC from the device name list. - If you connected an AV device to the HDMIIN 2 (DVI) port with an HDMI to DVI cable, select DVI Devices from the device name list. • Information: View detailed information about the connected devices. • Refresh: Select if a connected device does not appear in the list. If the list does not show the device after selecting Refresh, check the status of the 1V-to-device connection. • Remove USB: Remove the USB device from the list safely. This function is only available when the USB device selected . Universal Remote Setup: Use to configure universal remote control settings. Using the universal remote control, you can control external devices connected to the 1V, such as a set-top box, Blu-ray player, and AV receiver. Universal Remote Control Setup This TV has a universal remote control feature that lets you control cable boxes, Blu-ray players, home theaters, and other third-party external devices connected to the TV using the TV's remote control. -------- ... , ,, I I II I I I I ,/',' '' lljellil ' J-(Q)·~ '\ ' \ I I I ... ~",,".I I I I I I I ,, ,, , I I ,' Keep a distance of 0.16 ft at least between the IR Extender and the external device, as the illustration shows. Face the IR Extender toward the external device's remote control signal receiver. Note that it should be no obstacle between IR Extender and external device. The presence of an obstacle will interfere with the transmission of the remote control signal. Add the External Device 1. Turn on the external device you wish to set up universal remote function for and then press SOURCE to bring up the Source screen. 2. Select Universal Remote Setup from the top of the screen. This initiates the universal remote setup process. 3. Follow the on-screen instruction and set up the universal remote control. If it does not work, set up the remote control by entering the model number manually. Viewing the e-Manual This TV has a built-in e-Manual that contains information about your TV's key features and instructions for using them. To view thee-Manual, use one of the following methods: • Open the Support menu and choose e-Manual. • Press the MORE button on the Smart Touch Control to display the virtual remote control on the TV screen. Flick the Touch Pad until the Quick Access Panel appears, select the e-Manual icon, and then press the Touch Pad. ~ In thee-Manual, words in blue refer to screen menu options and words in light blue refer to remote control buttons. ~ A printable version of this guide is also available at www.samsung.com/support. Scrolling a Page To scroll a page, use of one of the following methods: or button at the right edge of the screen, and then tap the Touch Pad . • Place the focus on the • Drag or flick up or down from either edge of the touchpad. • ;~' or Place the focus on the lill±t< Touch Pad. button at the right edge of the screen, drag or flick up or down on the Using the Top Icons. Use the Back, Forward, and Opened pages icons on the top left of the screen to navigate through pages. These icons are available after you have viewed two or more pages. Returning to the Home Page To return to the home page, select the r.J button or select ~ A on the top right of the screen. To select a letter button (r.J, rn. [!), l!l), press the MORE button on the Smart Touch Control to display to display the virtual remote control on the TV screen. Flick the Touch Pad until the Playback Control Panel appears, select the r.J button, and then press the Touch Pad. Searching the Index Select the rn button or select & on the top right of the screen to display the index. Select a term to display the page containing the term. Searching Pages Select the (!I button or select ~ on the top right of the screen, and enter search criteria. Select a page from the list of search results to display it. Closing the e-Manual To close the e-Manual, press hold the RETURN button or select screen. X at the upper-right corner of the Jumping to a Menu Item To jump directly to the menu item that is described in the current section, select ~.!J. It is possible to jump from a menu item directly to the related section in thee-Manual. On a menu screen , press the MORE button on the Smart Touch Control and then select e-Manual on the virtual control panel that appears on the screen. ~ This feature may not be available, depending on the menu . Updating thee-Manual Open the Smart Hub and select Apps, and then select Downloaded. Thee-Manual can be updated in the same way with an application update. On the Downloaded screen, select Edit, and then select Update Apps. Select e-Manual from the list. The e-Manual starts updating to the latest version. Connecting to a Network Connecting the TV to a network gives you access to online services such as Smart Hub and lets you update the TV's software online directly from Samsung.com. Network Connection - Wireless Connect the TV to the Internet using a standard wireless router or modem. Wireless IP Router or Modem that has a DHCP Server The LAN Port on the Wall LAN Cable (Not Supplied) Wireless Network Precautions • This TV supports the IEEE 802.11 a/b/g /n communication protocols. Samsung recommends using IEEE 802.11 n. Otherwise, when you play video over a network connection, the video may not play smoothly. • To use a wireless network, the TV must be connected to a wireless router or modem. If the wireless router supports DHCP, the TV can use a DHCP or static IP address to connect to the wireless network. • Select a channel that is not currently in use for the wireless router. If the channel set for the wireless router is currently being used by another device, the result is usually interference and/or a communications failure. • Most wireless networks have an optional security system. To enable a wireless network's security system, you need to create a security key using characters and numbers, and then enter that key into the router through its menu. You then must enter this security key into any other devices you want to connect to the wireless network. Network Security Protocols The TV only supports the following wireless network security protocols: • Authentication Modes: WEP, WPAPSK, WPA2PSK • Encryption Types: WEP, TKIP, AES In compliance with the newest Wi-Fi certification specifications, Samsung TVs do not support WEP or TKIP security encryption in networks running in the 802.11 n mode. If the wireless router supports WPS (Wi-Fi Protected Setup), you can connect the TV to your network using PBC (Push Button Configuration) or a PIN (Personal Identification Number). WPS automatically configures the SSID and WPA key settings. Your Smart TV cannot connect to uncertified wireless routers. Network Connection- Wired There are three main ways to connect your 1V to your network using cable, depending on your network setup. They are illustrated below: TV Rear Panel External Modem (ADSL I VDSL I Cable TV) The Modem Port on the Wall Modem Cable (Not Supplied) LAN Cable (Not Supplied) TV Rear Panel The Modem Port on the Wall External Modem (ADSL I VDSL I Cable TV) Modem Cable (Not Supplied) IP Router that has a DHCP SeNer LAN Cable (Not Supplied) LAN Cable (Not Supplied) TV Rear Panel The LAN Port on the Wall LAN Cable (Not Supplied) ~ The TV does not support network speeds less than or equal to 10Mbps. ~ Use Cat 7 cable for the connection. 3D Active Glasses Features Samsung's SSG-5 100GB 30 glasses enable you to view 30 images on your 30 TV. The Samsung 30 glasses communicate with Samsung 30 TVs via the 2.4GHz RF band. ~ The Samsung 30 glasses are only compatible with Samsung D, E, and F series 30 TV's that were released in 2011, 2012, and 2013. These 30 glasses cannot be connected to other Bluetooth devices. Parts LED Indicator & Power Button ~ For details on how to attach the glasses' temples, refer to the separate 30 glasses manual. Replacing the Battery If the red LED blinks every two seconds continually, replace the battery with a new one. ~ Insert the "+" side of the battery into the side marked with "+" in the battery compartment. ~ To check the remaining battery capacity, refer to the pairing section in this manual . .. .. Pull the battery cover downward Open the battery cover Remove the battery Replace the battery Push the battery cover downward Close the battery cover Pairing 3D Active Glasses ~ What is Pairing? Pairing is the process of connecting 30 glasses and a 30 TV so that the two devices can exchange data. ~ Ensure your Samsung TV and 30 glasses are no farther than 19.5 in (50 em) apart from each other while pairing is in progress. • Turning the glasses on Press the power button briefly. The green LED turns on for 3 seconds. (Make sure that 3D is activated on the lV before using the 3D glasses.) • Turning the glasses off Press the power button briefly. The red LED turns on for 3 seconds. • Performing the pairing process Turn the lV on and let it power up completely. Press and hold the Power button on the glasses. The green and the red LEDs blink alternately for 2 seconds. • Operating range Recommended pairing distance l~ ~ ~ Once the 3D glasses are paired, the remaining battery capacity is displayed on the TV screen. (This feature only applies to Samsung F series 3D TVs and 3D glasses that have been available since 2013.) ~ If you keep trying to pair the glasses and the TV after pairing has failed, the battery level will decrease significantly. However, the battery level will recover to a certain degree in about a minute. ~ The working distance is affected by the presence of obstacles (a person, metal, walls, etc.) between the glasses and the TV and the strength of the Bluetooth signal. ~ Turn off the 3D glasses when they are not in use. If you leave the 3D glasses on, the battery lifespan decreases. Pairing steps 1. Turn on the lV, and then move the glasses within 19.5 inches of the lV. 2. Press the power button on the 3D glasses briefly. The 3D glasses will power on and pairing will start. 3. The message "3D glasses are connected to lV." will be displayed on the lV screen when the pairing is successfully completed. • If pairing fails, the 3D glasses will power off. • If the first attempt to pair fails, power the lV off and on again and perform step 2. • How to pair again: Press the power button on the 3D glasses for more than 1 second. You must pair the glasses again in the following situations: - If the 3D glasses do not function, even when the power button is pressed, especially if the lV has just been a repaired. - If you want to play 3D content on another Samsung 3D lV model that belongs to the D, E, or F series released in 2011 through 2013. You must pair the glasses with the other lV. Watching 3D Video Some 3D modes may not be available depending on the format of the image source. To watch in 3D, you must wear 3D Active Glasses and turn the glasses on by pressing the power button. 1. Go to the 3D screen. (Picture> 30) 2. Select the 3D Mode. The 3D Mode screen appears. 3. Set the 3D Mode of the image you want to view. Troubleshooting The 3D glasses should be close to the 1V. Make sure that the distance between the 1V and your 3D glasses is less than 19.5 feet (6m) in a straight line. Specifications (Model Number: SSG-51OOGB) Liquid crystal 36±2% 2 - 6m (6.5 to 19.5 ft) 120 fields/second 21 .5g/.76 oz. (including the battery: 24.0±0.5g/ .85.±.018oz. ) One 3V lithium/manganese dioxide battery 3V (CR2025) 165mAh, 3.0V (CR2025) 150 hours ~ Product specifications may be changed without notice in order to enhance product performance. ~ The continuous operating time may differ depending on the wireless communication environment and usage conditions. What is Remote Support? Samsung Remote Support service offers you one-on-one support with a Samsung Technician who can remotely: • Diagnose your 1V • Adjust the TV settings for you • Perform a factory reset on your 1V • Install recommended firmware updates How Does it Work? Having a Samsung Tech remotely service your 1V is easy. 1. Call the Samsung Contact Center and ask for remote support. 2. Open the menu on your 1V and go to the Support section. 3. Select Remote Management and Provide the Pin# to the agent. 4. The agent will then access your TV. That's it! Troubleshooting If the TV seems to have a problem, first review this list of possible problems and solutions. Also, review the Troubleshooting Section in the e-Manual. If none of the troubleshooting tips apply, visit www.samsung. com/support or call Samsung Customer Service at 1-800-SAMSUNG (1-800-726-7864). Flickering and Dimming If your Samsung Television is flickering or dimming sporadically, you may need to disable some of the energy efficiency features. Disable Energy Saving (System > Eco Solution > Eco Sensor} and/or Energy Saving (System > Eco Solution > Energy Saving} and check again. Component Connections /Screen Color If you find that the color on your Samsung television screen is not correct or the black and white colors are off, run a Self Diagnosis Picture Test (Support > Self Diagnosis > Picture Test}. If the picture problem is caused by the TV, the problem should be visible in the Picture Test. If the problem is not visible, next confirm that the TV's video input jacks are connected to the correct external video device output jacks and that none of the connections are loose. Finally, if possible, test your external video devices by connecting them to another TV. Screen Brightness If you find that the colors on your Samsung TV are correct but just a little too dark or bright, try adjusting the following settings first. Navigate to Picture and adjust Backlight I Cell Light (applicable models}, Contrast, Brightness, Sharpness, Color, Tint (G/R) and other picture quality adjustment settings. Auto Motion Plus/ Blur If you find that there is a blur or "ghost" shadow to the images on your television screen, you might be able to correct the issue using Auto Motion Plus (Picture > Picture Options > Auto Motion Plus). Unwanted Powering Off If your Sam sung TV appears to turn off by itself, try disabling some of the TV's energy efficiency and automatic off features. Check if Sleep Timer (System > Time > Sleep Timer} has been enabled. Sleep Timer automatically turns off the TV after an amount of time that you select. If the Sleep Timer has not been enabled, see if No Signal Power Off (System > Eco Solution > No Signal Power Off) or Auto Power Off (System > Eco Solution > Auto Power Off) has been enabled. No Signal Power Off turns off the TV if no signal has been received by the TV for a specified period time. Auto Power Off turns off the TV if there has been no user input in four hours. Trouble Powering On When the TV is turned on, the remote control receiver flashes 5 times before the screen turns on. If you find that you are having problems powering on your Samsung television, there are a number of things to check before calling the service department. If the power cord is connected properly and the remote control is operating normally, the problem might be with the antenna cable connection or the cable/satellite box not being turned on. Check the antenna connection or turn on the cable/satellite box. Stand Assembly If you have any trouble assembling the stand, review the stand assembly instruction in the Quick Start Guide. Cannot Find a Channel Re-run Setup (Go to Menu > System > Setup) or run Auto Program. (Go to Menu > Broadcasting > Auto Program}. ~ For detailed troubleshooting information, watch the troubleshooting videos at www.samsung.com/ spsn. The TV won't turn on. • Make sure the AC power cord is securely plugged in to the wall outlet and the TV. • Make sure the wall outlet is working. • Try pressing the C) button on the TV to make sure the problem is not the rernote. If the TV turns on, refer to "Remote control does not work" below. There is no picture/video. • Check the cable connections. Remove and reconnect all cables connected to the TV and external devices. • Set the video outputs of your external devices (Cable/Sat Box, DVD, Blu-ray etc) to match the TV's input connections. For example, if an external device's output is HDMI, it should be connected to an HOM I input on the TV. • Make sure your connected devices are powered on. • Be sure to select the correct input source. • Reboot the connected dev1ce by unplugging it, and then reconnecting the device's power cable. The remote control does not work. • Replace the remote control batteries. Make sure the batteries are installed with their poles(+/-) in the correct direction. • Clean the sensor's transmission window on the remote. • Try pointing the remote directly at the TV from 5- 6 feet away. The cable/set top box remote control doesn't turn the TV on or off or adjust the volume. • Program the Cable/Set remote control to operate the TV. Refer to the Cable/Set-Top-Box user manual for the SAMSUNG TV code. ~ This TFT LED panel uses a panel c onsisting of sub pixels which require sophisticated technology to produce. There may be, however, a few bright or dark pixels on the screen. These pixels will have no impact on the performance of the product. ~ To keep your TV in optimum condition , upgrade to the latest software. Use the Update Now or Auto Update functions on the TV's menu (Screen Menu > Support > Software Update > Update now or Screen Menu > Support > Software Update > Auto Update). Mounting the TV on the Wall Using the Wall Mount Kit (Optional) Wall or Ceiling Mounting If you mount this product on a wall, it should be mounted only as recommended by the manufacturer. Unless it is correctly mounted, the product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Installing the Wall Mount Kit The wall mount kit (sold separately) lets you mount the TV on the wall. For detailed information about installing the wall mount, see the instructions provided with the wall mount. We recommend you contact a technician for assistance when installing the wall mount bracket. We do not advise you to do it yourself. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own. To order the wall mount kit, contact Samsung Customer Care at 1-800-SAMSUNG (1-800-726-7864). Installing a Wall Mount Using the Wall Mount Adapter . ... •• rI ••• ............... ••·••• I ~ For more detailed information, refer to the User Manual of the Wall Mount Kit. VESA Wall Mount Kit Notes and Specifications ~ Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information. If you install the TV on a ceiling or slanted wall, it may fall and result in severe personal injury. ~NOTE • Standard dimensions for wall mount kits are shown in the table below. • Samsung wall mount kits contain a detailed installation manual, and all parts necessary for assembly are provided. • Do not use screws that do not comply with VESA standard screw specifications. • Do not use screws that are longer than the standard length or do not comply with VESA standard screw specifications. Screws that are too long may cause damage to the inside of the TV set. • For wall mounts that do not comply with the VESA standard screw specifications, the length of the screws may differ depending on the wall mount specifications. • Do not fasten the screws too firmly. This may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents. • Samsung is not liable for product damage or personal injury when a non-VESA or non-specified wall mount is used or the consumer fails to follow the product installation instructions. • Do not mount the TV at more than a 15 degree tilt. • Always have two people mount the TV on to a wall. 40- 46 200 X 200 LED-1V [Ultra Slim] MB 55 - 60 4 400 X400 Do not install your Wall Mount Kit while your TV is turned on. It may result in personal injury from electric shock. Assembling the Cable clip Assembling the Screw Cover Assembling the Power inlet Cover 0 0 Eco Sensor and Screen Brightness .. Eco Sensor measures the light in your room and optimizes the brightness of the TV automatically to reduce power consumption. This causes the TV to brighten and dim automatically. If you want to turn this function off, go to Menu > System > Eco Solution > Eco Sensor Do not block the sensor with any material. It can decrease picture brightness. Maintenance ~ If a sticker was attached to the TV screen, some debris can remain after you remove the sticker. Please clean the debris off before watching TV. ~ The exterior and screen of the product can get scratched during cleaning. Be sure to wipe the exterior and screen carefully using a soft cloth to prevent scratches. Providing Proper Ventilation for Your 1V When you install your TV, maintain a distance of at least 4 inches between the TV and other objects (walls, cabinet sides, etc.) to ensure proper ventilation. Failing to maintain proper ventilation may result in a fire or a problem with the product caused by an increase in its internal temperature. ~ Whether you install your TV using a stand or a wall-mount, we strongly recommend you use parts provided by Samsung Electronics only. • If you use parts provided by another manufacturer, it may cause difficulties with the product or result in injury caused by the product falling . ____________ T_________ ___ _ : ' ' 4 inches: 4 inches : ' ' ~s ~ "---------- -·r-4 1nches ' ~- ---- - - - - ' ' 4 inches : ~ I -,' ' ' : 4 inches r' :---------------]4 inches _________ _.: Other Warnings ~ The actual appearance of the TV may differ from the images in this manual, depending on the model. ~ Be careful when you touch the TV. Some parts can be warm or hot. Securing the TV to the Wall Caution: Pulling, pushing, or climbing on the TV may cause the TV to fall. In particular, ensure your children do not hang on or destabilize the TV. Doing so may cause the TV to tip over, causing serious injuries or death. Follow all safety precautions provided in the Safety Flyer included with your TV. For added stability and safety, you can purchase and install the anti-fall device as described below. Installing the TV-Holder Kit: 1 . Screw the provided wall mount adapters on the back of the lV .·......········"·····..... ....... ....... . : ...·· ... ············ 2. Insert the screw into the center of the lV-holder, as shown by the illustration. Fastening direction~ Holder Protrusion 3. Tighten the lV-holders on the wall mount adapters, as shown by the illustration. 4. Fasten the Holder to the cabinet using a wood screw. ~ Using an M5 x L35 or a larger screw. 5. Fasten the Holder with a screw the same way used when attaching it to a cabinet. Make sure to stretch the Holder cord tight. If the rack is made of steel or glass, attach the holder onto the wall. ~ When attaching the holder onto a wall, use an anchor compatible with the wall's material. When attaching the holder onto a wall, use an anchor compatible with the wall material. Anchor ~ Install the TV close to the wall so that it does not fall. ~ When attaching the TV-Holder cord to the wall, tie the cord level with the ground or slanted downwards for safety purposes. ~ Check the cord occasionally to make sure it is secure. ~ Before moving the TV, separate the connected cord first. 6. Verify all connections are properly secured. Periodically check the connections for any sign of fatigue or failure. If you have any doubt about the security of your connections, contact a professional installer. IMPORTANT INFORMATION If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as: • Using cabinets or stands recommended by the manufacturer of the television. • Only using furniture that can safely support the television . • Ensuring the television is not overhanging the edge of the supporting furniture. • Not placing the television on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television to a suitable support. • Not standing the televisions on cloth or other materials placed between the television and supporting furniture. • Educating children about the dangers of climbing on furniture to reach the television or its controls. Specifications 50'F to 104' F (1O'C to 40°C) 10% to 80%, non-condensing -4°F to 113°F (-20°C to 45°C) 40W 0 x 2, woofer 10 x 40.6 x 23.6 x 1.3 inches (1 032.7 x 599 5 x 34 9 mm) 40.6 x 24.9 x 10.1 inches 1032.7 x 634.3 x 257.7 mm) 48.1 x 27.8 x 1.3 inches (1224.2 x 707.2 x 34.9 mm) 48.1 x 29.2 x 12.2 inches 224.2 x 741.9 x 310.3 mm) 40W (10 x 2, woofer 10 x 2) 53 0 x 30.6 x 1.5 1nches (1346.9 x 778.0 x 38.4 mm) 53.0 x 31.9 x 13.5 inches (1346.9 x 812.7 x 343.3 mm) 45.0 lbs (20.45 kg) 48.91bs ~ Design and specifications are subject to change without prior notice. ~ The actual appearance of the TV may differ from the images in this manual, depending on the model. ~ This device is a Class B digital apparatus. ~ For information about the power supply, and more information about power consumption, refer to the label attached to the product ~ Typical power consumption is measured according to Energy Star Program requirements for Televisions. Dispose unwanted electronics through an approved recycler. To find the nearest recycling location, go to our website: www.samsung.com/recyclingdirect or call, (877) 278- 0799 Standby mode To decrease power consumption, unplug the power cord when you don't intend to use the TV for a long time. Dimensions • Jack panel detail I Rear view (Unit: inches) NOTE: All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice. Refer to the dimensions before installing your TV. Not responsible for typographical or printed errors. © 2013 Samsung Electronics America, Inc Licenses [I] DOLBY. DIGITAL PLUS PULSE I I ~db Premium Sound 15.1 DIVX:. HD Warranty Information Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation . This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. For product available in the US.AJCanada market, only channel 1-11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be colocated or operation in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de Ia classe B conforms Ia norme NMB-003 du Canada. a This device complies w ith Industry Canada licenseexempt RSS standard(s) . Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforms aux CNR d'lndustrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'apparei l doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d 'en compromettre le fonctionnement. For product available in the US.AJCanada market, only channel 1-11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be colocated or operation in conjunction with any other antenna or transmitter. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT WARRANTY INFORMATION REGARDING TELEVISION FORMAT VIEWING ~ The above described warranty repairs must be performed by a SAMSUNG Authorized Service Center. Along with this Statement, the Original Limited Warranty Statement and a dated Bill of Sale as Proof of Purchase must be presented to the Service Center. Transportation to and from the Service Center is the responsibility of the purchaser. Conditions covered are limited only to manufacturing defects in material or workmanship, and only those encountered in normal use of the product. See the warranty card for more information on warranty terms. Wide screen format LED Displays (with 16:9 aspect ratios, the ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen, 16:9 ratio format, or expanded to fill the screen, if your model offers this feature, with the images constantly in motion. Displaying stationary graphics and images on the screen, such as the dark sidebars on nonexpanded standard format television video and programming, should be limited to no more than 5% of the total television viewing time per week. Additionally, viewing other stationary images and text such as stock market crawls, video game displays, station logos, web sites or computer graphics and patterns, should be limited as described above for all televisions. Displaying stationary images that exceed the above guidelines can cause uneven aging of LED Displays that leave subtle, but permanent burned-in ghost images in the LED picture. To avoid this, vary the programming and images, and primarily display full screen moving images, not stationary patterns or dark bars. On LED models that offer picture sizing features, use these controls to view different formats as a full screen picture. Be careful about the television formats you select and the length of time you view them. Uneven LED aging as a result of format selection and use, as well as burned in images, are not covered by your Samsung limited warranty. • Excluded, but not limited to, are any originally specified provisions for, in-home or on-site services, minimum or maximum repair times , exchanges or replacements, accessories, options, upgrades, or consumables. For the location of a SAMSUNG Authorized Service Center, please call toll-free: In the United States: 1-800-SAMSUNG (1 800-726-7864) - In Canada: 1-800-SAMSUNG Still image warning Avoid displaying still images (such as jpeg picture files), still image elements (such as TV channel logos, stock or news bars at the screen bottom etc.), or programs in panorama or 4:3 image format on the screen . Constantly displaying still pictures can cause image burn-in on the LED screen, which will affect image quality. To reduce risk of this effect, please follow the recommendations below: • Avoid displaying the same TV channel for long periods. • Always try to display any image in full screen. Use the TV set 's picture format menu for the best possible match. • Reduce brightness and contrast to avoid the appearance of after-images. • Use all TV features designed to reduce image retention and screen burn . Refer to the e-Manual for details. SAMSUNG ELECTRONICS NORTH AMERICAN LIMITED WARRANTY STATEMENT Subject to the requirements, conditions, exclusions and limitations of the original Limited Warranty supplied with Samsung Electronics (SAMSUNG) products, and the requirements, conditions, exclusions and limitations contained herein, SAMSUNG will additionally provide Warranty Repair Service in the United States on SAMSUNG products purchased in Canada, and in Canada on SAMSUNG products purchased in the United States, for the warranty period originally specified, and to the Original Purchaser only. - Regulatory Compliance Statements (For 3D Active Glasses) FCC COMPLIANCE Federal Communication Commission Interference Statement 1. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part ~ 5 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio!TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (~) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CALIFORNIA USA ONLY This perchlorate warning applies only to primary CR (Manganese Dioxide) Lithium coin cells in the product sold or distributed ONLY in California USA " Perchlorate Material - special handling may apply, See www. dtsc. ca. gov/ hazardouswaste/ perchlorate." SAMSUNG BRAND PRODUCTS LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for a limited warranty period of 90 Days Parts and Labor for Commercial Use Categories LCD/LED1V Parts 1 Year Size Labor Service 40" and Larger Carry-In or In Home 37" and Smaller Carry-In 1 Year Plasma Display 1 Year 1 Year All Carry-In or In Home Projector (Excluding Lamp **) 2 Year 2 Year All Carry-In or Pick up Carry-In or PICO & LED 1 Year All 1 Year Pick up Pocket Projector •• 180 Days after 1-'urchasing and 600 Hours of Use Lam p on Pro ector This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States. To receive warranty service, the purchaser must contact SAMSUNG for problem determination and seNice procedures. Warranty seNice can only be perlormed by a SAMSUNG authorized seNice center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG 's authorized seNice center. SAMSUNG will repair or replace this product, at our option and at no charge as stipulated herein, with new or reconditioned parts or products if found to be defective during the limited warranty period specified above. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assurne the remaining original warranty, or ninety (90) days, whichever is longer. Certain products are eligible for In-home seNice at Samsung's discretion. To receive in-home seNice, the product must be unobstructed and accessible to seNice personnel. If during in-home seNice, repair cannot not be completed, it may be necessary to remove, repair and return the product. If in-home seNice is unavailable, SAMSUNG may elect, at our option, to provide for transportation of our choice to and from a SAMSUNG authorized seNice center. Otherwise, and tor 37" and smaller LCD/LED 1V, transportation to and from the SAMSUNG authorized seNice center is the responsibility of the purchaser. This limited warranty covers manufacturing detects in materials and workmanship encountered in normal, and except to the extent otherwise expressly provided for in this statement, noncommercial use of this product, and shall not apply to the following, including, but not limited to: damage which occurs in shipment; delivery and installation; applications and uses for which this product was not intended; altered product or serial numbers; cosmetic damage or exterior finishes; accidents, abuse, neglect, fire, water, lightning or other acts of nature; use of products, equipment, systems, utilities, seNices, parts, supplies, accessories, applications, installations, repairs, external wiring or connectors not supplied or authorized by SAMSUNG which damage this product or result in seNice problems; incorrect electrical line voltage, fiuctuations and surges; customer adjustments and failure to follow operating instructions, cleaning, maintenance and environmental instructions that are covered and prescribed in the instruction book; reception problems and distortion related to noise, echo, interlerence or other signal transmission and delivery problems; brightness related to normal aging, or burnedin images. SAMSUNG does not warrant uninterrupted or error-free operation of the product. THERE ARE NO EXPRESS WARRANTIES OTHER THAN THOSE LISTED AND DESCRIBED ABOVE, AND NO WARRANTIES WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, SHALL APPLY AFTER THE EXPRESS WARRANTY PERIODS STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY GIVEN BY ANY PERSON, FIRM OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG. SAMSUNG SHALL NOT BE LIABLE FOR LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS, OR ANY OTHER SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES CAUSED BY THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOR SHALL RECOVERY OF ANY KIND AGAINST SAMSUNG BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCT SOLD BY SAMSUNG AND CAUSING THE ALLEGED DAMAGE. WITHOUT LIMITING THE FOREGOING, PURCHASER ASSUMES ALL RISK AND LIABILITY FOR LOSS, DAMAGE OR INJURY TO PURCHASER AND PURCHASER'S PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF THE USE, MISUSE OR INABILITY TO USE THIS PRODUCT SOLD BY SAMSUNG NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF SAMSUNG. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL PURCHASER OF THIS PRODUCT, IS NONTRANSFERABLE AND STATES YOUR EXCLUSIVE REMEDY Some states do not allow limitations on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. To obtain warranty seNice, please contact SAMSUNG at: Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660-2112 1-800-SAMSUNG (7267864) - www.samsung.com 1-800-749-0260: Projectors only Contact SAMSUNG WORLDWIDE If you have any questions or comments about Your Samsung lV, please contact the SAMSUNG customer care center. U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660 1111111111111111111111111111111111111111111 © 2013 Samsung Electronics Co., Ltd. All rights reserved. BN68-04786A-01 QUICK START GUIDE 11111111111111111.11111 BN68-05037A-00 Attach the TV to the Stand Connect video devices Insert the batteries into the remote control Power on and start the initial setup Welcome to your new Smart TV! The following instructions cover assembling, connecting, and setting up your new TV. Make sure you have the accessories listed below. Included in this box , Remote Control Stand Parts and Cables lx2 SmartTouch Control ~ Batteries (AAA x 2) Screw Cover Cable clip x2 f?CJ \J Wall mount adapter TV holder kit Power cord !D -~ 0 ~ RCA Adapter x 2 Step 7 Power inlet cover --. Component adapter IR extender Attach the TV to the Stand Open the package, and take the cushioning out of it. Lay the TV on a soft surface, screen side down. Use the packing material to protect the screen. 5 Holding the stand parallel to the screen, slide the stand legs into the notches on the back of the TV. Put a base, legs and screws off to assemble the stand out of the box. 2 ~ ~ ~~:_! Base Leg Screws '"----------------------------------'' Fit the base and legs together, making sure that the legs are firmly aligned with the base. See the diagram below. Insert 2 screws through the base into each leg as shown, and then secure the legs to the base with a screwdriver. ~ x4(M4Xl12) 8 Insert 4 screws and secure the stand to the TV. When placing the product on a console or shelf, make sure that the stand does not protrude out of t he console or shelf. This may cause the product to fa ll off and resu lt in a malfunction or Step 2 Connect video devices We suggest using HDMI connections whenever possible for the best picture quality. Use the included AV adapter to connect older devices. Power Input USB Connections The AUDIO OUT port can connect to a speaker. You can connect USB storage devices to the USB jacks and enjoy personal photos, videos, and music. You can connect home theater systems to the OPTICAL or AUDIO OUT ports. Best Connection : HDMI We suggest using HDMI whenever possible. HDMil is the default port for a cable or satellite set-top box. _) -- Good Connection :Component and AV Match the colors on your device's cables to the colors on the jacks. Connect the yellow composite video out connector from an AV device to the yellow AV IN jack. HDMICable HDMIPort ~ .> •> ~ - ~ ~~.?.;.;; Connect the IR extender to the IR Out port to control external devices connected to the TV using the Smart Touch Control. For more detailed information, refer to the "Universal Remote Control Setup" section on the User manual. Wired Ethernet Insert the batteries into the remote control • (!) Connect the cable from the antenna or cable TV outlet. Make sure you have the correct cable before plugging it in. Illustrations of common plugs and jacks are shown below. To open, put your plastic card into the notch. Cable Plugs HDMI""" Step 4 ::E AV (!) Step 3 ~ Component Use the other ports for Blu-ray players, game consoles, and other devices. II Power on and start the initial setup Information required: USB ' Optical ' Troubleshooting -• Warning Do not plug cables in upside down. Be sure to check the orientation of the plug before plugging it in. The stand is wobbly or crooked Wi-Fi network password (if you use one) Make sure the arrows on the stand are properly aligned. Zip code The TV won't turn on Cable or satellite provider info The TV must be connected to the Internet to use the Smart Features. If you have a wireless network, we recommend that you confirm that your network router is switched on and working before you start the initial setup. If you have a wired network, we recommend that you connect the TV to the network with a CAT 7 cable before you begin. Make sure all cables are fully inserted, and that the remote has batteries installed. My remote, gesture, or voice controls don't work The TV ships with protective stickers covering some of the sensors. Make sure all of them have been removed. I don't know where to plug in <device> ( ! ) Power on to start the Initial setup. Devices without HDMI may require the included AN adapter. Connect to your network (wired or wireless) . L__=; Search for channels from your TV service provider r! ((< . . or After you have finished the initial setup, you can configure the universal remote control settings. These settings let the Smart Touch remote control external devices connected to the TV, such as a set·top box or Blu-ray player. Congratulations on your new Smart TV! I have extra parts The TV includes some optional parts to help with wall mounting and cable routing. If you experience issues, please do not take the TV back to the store. In the United States of America, call us at 1-800-SAMSUNG (1-800-726-7864) or visit us at www. samsung.com/spsn for support and warranty service. For other countries, refer to "Contact SAMSUNG WORLDWIDE" in the user guide. IMPORTANT SAFETY PRECAUTIONS If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries, particularly to children, can be avoided by taking simple precautions such as: • Placing the television on a platform, stand, cabinet, table or other surface which is: - recommended by Samsung or sold with the product; - secure and stable; - sufficiently wider in the base than the base measurement of the television; strong and large enough to support the size and weight of the television. • Positioning the television close to the wall to avoid the possibility of the television falling when pushed. • Ensuring your television is installed by an authorized Samsung installer. • Following the instructions for wall mounting in the installation manual and using the mounting equipment supplied by Samsung. • Placing the television toward the back of the furniture or surface on which it is placed. • Ensuring that the television does not hang over the edge of the furniture or surface on which it is placed. • Not hanging anything from or on the television. • Anchoring both the television and the furniture on which it is placed to a suitable support especially in the case of tall furniture, such as • cupboards or bookcases which exceed one metre in height. This can be done by using sturdy brackets, safety straps or mounts that are made specifically for flat screen televisions. • Not placing any material between the television and the furniture on which it is placed. • If the furniture on which the television is placed has drawers, cabinets or shelves under the television, taking steps to prevent children from climbing, such as Installing safety latches so the doors cannot be opened. • Keeping pets away from the television • Educating children about the dangers of climbing on furniture to reach the television or its control. Failure to take these safety precautions may cause the television to fall from the stand or mounting equipment, causing damage or serious injury. Regulatory Compliance Statements Your Samsung product compliance class is marked in the user manual - Federal Communications Comm ission (FCC) - USA Industry Canada Equipment Standard for Digital Equipment (ICES-003) - Canada Voluntary Control Council for Interference (VCCI) - Japan Bureau of Standards Metrology and Inspection (BSMI) - Taiwan Korea Communications Commission(KCC) - Republic of Korea Italian Post Ministry (Homologation) - Italy FCC Class A Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. ~ This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. FCC Class B Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. ~ This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonab le p rotection against harmful interference in a residential installation . This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance w ith the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference w ill not occur in a particular installation . If this equipment does cause harmful interference to radio or television reception, w hich can be determined by turning the equip ment off and on, the user is encouraged to t ry to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected . - Consult t he dealer or an experienced radio/TV technician for help . User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. If necessary, consult with your dealer or an experienced radio/television technician for additiona suggestions. You may find the booklet called How to Identify and Resolve Radio!TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. It is available from the U.S. Government Printing Office. Washington, DC 20402, Stock Number 004-000-00345-4 . The party responsible for product compliance: SAMSUNG ELECTRONICS CO , LTD. America QA Lab of Samsung 335 1 Michelson Drive Su1te #290, Irvine, CA92612 USA Warning User must use shielded signal interface cables to maintain FCC compliance for the product. Provided with this monitor is a detachable power supply cord w ith IEC320 style terminations. It may be suitable for connection to any UL Listed personal com puter with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as t he monitor and that the ampere rating of the computer convenience outlet is equal or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type(parallel blades) plug cap . For 240 Volt applicat ions use only UL Listed detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. This television receiver provides display of television closed captioning in accordance with Section 15.1 19 of the FCC rules. (TV broadcast receivers with picture screens 13 inches or larger in diameter models only) ICES-003 Class A Notice -Avis NMB-003, Classe A This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numerique de Ia classe A est conforme a Ia norme NMB-003 du Canada. ICES-003 Class B Notice - Avis NMB-003, Classe B This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numerique de Ia classe B est conforme a Ia norme NMB-003 du Canada. VCCI Class A Notice ;:: O)~Jilj:, ? 7 'A A 1U!Hif~f~ii't''9 o ;:O)~jitf~fi!Ji±Jl't'fi!Jfl'9 .Q c ~ i&:YJi~t!-512'~:: '9;:: c tJ<'&J L) ;J;:'9 ::: O)~~r::rj:-~tm~n<~tJJtJM~ tf~1ij9 .Q J:? ~* ~ n.Q::: e: n<"&J LJ *'9 0 0 VCCI Class B Notice ;:: O)~jilj:, ? 7 'A B f~lativr.f~~'t''9 o ::: O)~Ji lj:, ~fi!!i±Jl-c-~tm'9 .Q::: e: tf 13 !¥.1 e: L- -ct.' ;J;:'9tJ<, ::: O)~JitJ<7 -:;;;t~-r '-" t ' -:; 3 n.Q e:, ~i~~t~t!-512'~:: '9::: e: n<"&J LJ *'9 lfll :t.&§.5lBJJ'i' r ::vr "? -c JE L-t. 'lfll LJ 1& 1., tf L- -c l ' ~ t., ~~f§~r:::i!Ht L- -c -~tm ~ 0 0 CCC Class A notice - China ~~A·~~ . ~~~~-~ . ~ ~~~M~~~~-*~tt . ~~~ffl~l' . ~M - -ffl~~K~tt*UW~~fi~ma . BSMI Class A Notice The following statement is applicable to products shipped to Taiwan and marked as Class A on the product compliance label. !fi5t1!m:tt : ~~ ~~•m~~~ · tt®tt~~~~m~ · ~~-~~Mffi~~ · a~•m~T· ~m~e*¥*~~~~-~~fim · CE BSMI Class A Notice Products with the CE marking comply with the EMC Directive(2004/108/ EC) and the Low Voltage Directive(2006/ 95/ EC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: - EN55022: Radio Frequency Interference - EN55024: Electromagnetic Immunity of Information Technology Equipment - EN61000-3-2: Power Line Harmonics - EN61000-3-3: Voltage Fluctuations - EN55013: Radio disturbance characteristics of broadcast receivers and associated equipments - EN55020: Electromagnetic immunity of broadcast receivers and associated equipm European Class A Warning (If the user manual declares the product as Class A, following statement applies.) This is a class A product . In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. AE- 7/7/ (gj!F§ 'D*~t17/XfAH) ~-'f!.-@-( A8) ~;;:~n~::s:j~7 171£Ai JtfDH:A: ~ ~ :::_ A~§.;;: ~ :::_ ~::s:JO £ ~Li ef . Ol 7171:::. BE- 7/7/ (7fM§ o1 7171:::. Ol ~ ~ -9-2.lo~Aj7 11::J~2.~[]:j , 7 ~~2.12.1 :A: I ~ OliAi A~-@-ar:::. 3;1~ 'D*~t17/XfAH) 7~~§-(B sl ~:x fn~::s:J~7 1 7 1£Ai -9-£ 7 f~ Ol1 Ai Af-@-ar:::. 3;1~ ~::s:JO£ af[):j , Italian Homologation Notice Questo apparecchio e fabbricato in conformita al D.M.28.08 .95 n.548 ed in particolare a quanto specificato nell Art. 2, comma 1. Ouesto apparecchio e fabbricato nella U.E. in conformita al D.M.28.08.95 n.548 Art.2, comma 1 ed al D.M.26.03.92 Art.1 - For products produced in countries except European Community Questo apparecchio e fabbricato in conformita al D.M.28.08.95 n.548 ed in particolare a quanto specificato nell Art.2, comma 1 . - For products produced in European Community Questo apparecchio e fabbricato nella U.E. in conformita al D.M.28.08.95 n.548 Art. 2, comma 1 ed al D.M.26.03.92 Art.1 2.:::: :A: I ~OliAi N§~ * 'V~Li cf . EU Eco-Label (EU Eco-label applied model onty) Products which have model codes that end in XU are intended for the UK market. Samsung has not applied for Ecolabels for products with this specific model code. Better for the environment. .. • High Energy Efficiency • Reduced C02 emissions • Designed to facilitate repair and recycling ... better for you. www .ecola bel.eu [..___E_u_E_c_o_la_b_e_L_·H_u_,_o_22_J_o2_____] SAMSUNG Electronics makes an effort to develop environment-friendly product that minimtzing an impact to environment through whole process from getting raw matenals, production , transportation, usage and end-of- life disposal by adding 'environment' on function, price, quality, design that w ere the essence for product development. These environmental characteristics are endorsed by the award of the European Eco-label (also known as t he Euro Flower) issued by the European Commission as approval of the product environmental status for energy saving , facilities for recycling and a host of other features. The full list of criteria and more information on the ecolabel canbe found at the web-site address: http://www.ecolabel.eu Recycling Information (Tak~back offer) . - For recycling information for our products, please contact the company corresponding to your region of residence. For those who reside in other countries, please contact a nearest local Sam sung dealer for recycling information for the products to be treated in environmentally acceptable way. The information of Regional Takeback Schemes can be found at Samsung's web-site. http://www.samsung.com/recycling_compliance ® a ® l:J CI!1M80Il «He ):IIls:l nl!1lJ..l880Vl npOJ:IYK1..11111!1» np1!1M8 Hs:l8TC5l 8 COOT88TCT81!18 C T8XHI!148CKI!1M pernaMeHTOM TaMo>KeHHoro co103a «0 6e3onacHOCTI!1 ynaKOBKI!1» 005/2011 111 yKa3btsaer Ha ro, 4TO ynaKOBKa gaHHoro npogyKTa He npegHa3Ha4eHa ,Qilfl nosropHoro 1!1cnonb308aHI!15l 111 nogne>KI!1T yrl!1nl!13al..11!11!1. YnaK08KY ):18HHOrO npogyKTa 3anp8l1.188TC5l 1!1CnOilb3088Tb ):IIls:l XpaHeH1!15l nii1U1e80Vl npO.QYK1..11!11!1. C111Mson «neTnfl Me6111yca» yKa3btsaeT Ha so3MO>KHOCTb YTII1m1381..\vH1 ynaKOBKI!1 . Cii1MBon MO>KeT 6b1Tb AOnOnHeH 0603H8lf8HI!18M M8T8p1!18Il8 ynaK08KI!1 8 BI!1A8 l\111cppOBOrO 1!1/1!1Il~ 6yKB8HHOro 0603H8lf8HI!15l . CI!1M8on Ke,qeH,QiK o,[\a~Tblfi 005/2011 rexH~Kailbl~ pernaMeHTiHe caliiKec ~on,[\aHbiil8,[\bl >KaHe OCbl SHiMHifi ~8nT8M8CbiH 8KiHWi peT naLil,[\ailaHyfa apH8IlM8f8HbiH >K8H8 >KOIOf8 >K8T8TbiHbiH K8pC8T8,[\i. Ocbt eHiMHifi ~anraMaCbiH aabl~-ryniK eHiM,[IepiH ca~ray ywiH naV!,qanaHyra TbiVlbiM canbiH8Abl. C~Mson ~amaMaHbl >KOIO MYMKiHAiriH KepceTe,[li. C~Mson caHAbl~ KOA >KaHe/HeMece apin 6eminepi TypiHAeri ~anTaMa M8T8p~8Ilb1Hbll-\ 6enriciM8H TOilbi~TblpbiilYbl MYMKiH . 1111111111111111111111111111111111111111111 BN68-04972A-01 ' Wiring the Mains Power Supply Plug(UK Only) ' . IMPORTANT NOTICE The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on t he pin face of the plug and, if it requires replacing, a fuse approved to BSI1362 of the same rating must be used. Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug . Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance. However, if there is no alternative but to cut off the plug, remove the fuse and then safely dispose of the plug. Do NOT connect the plug to a mains socket as there is a risk of shock hazard from the bared flexible cord. IMPORTANT The wires in the mains lead are coloured in accordance with the following code: BLUE - NEUTRAL BROWN - LIVE As these colours may not correspond to the coloured markings identifying the terminals in your plug, proceed as follows : The wire coloured BLUE must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The wire coloured BROWN must be connected to the terminal marked with the letter Lor coloured BROWN or RED. WARNING: DO NOT CONNECT EITHER WIRE TO THE EARTH TERMINAL, WHICH IS MARKED WITH THE LETTER E OR BY THE EARTH SYMBOL , OR COLOURED GREEN OR GREEN AND YELLOW. Russia Only • PCT Notice , "- ~ ~ ~~ AB57 MPR ·11 Compliance (MPR II applied model only) This monitor complies w1th SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. ENERGYSTAR qualified model only - Your Samsung 1V is ENERGYSTAR qualified in its factory default settings. Change to certain features, settings and functionality in this 1V can change the power consumption, possibly beyond the limits required for ENERGYSTAR qualification. - As an ENERGY STAR Partner, Samsung has determined that this product or product models meets the ENERGY STAR guidelines for energy efficiency. . _ ~ Important Safety Instructions (UL Only) 1. 2. 3. 4. 5. 6. 7. 8. 9. 1 0. 11. 12. 13. 14. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings, Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Only use attachments/accessories specified by the manufacturer. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. Unplug this apparatus during lightning storms or when unused for long periods of time. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped . .& WARNING: To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. • Ventilation Do not place the apparatus in a rack or bookcase. Ensure that there is adequate ventilation and that you 've followed that manufacturer's instructions for mounting and installation. MPR II Compliance {MPR fl applied model only) This mon1tor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. ENERGYSTAR qualified model only - Your Samsung lV is ENERGYSTAR qualified in its factory default settings. Change to certain features, settings and functionality in this lV can change the power consumption, possibly beyond the limits required for ENERGYSTAR qualification. - As an ENERGY STAR Partner, Samsung has.determined that this product or product models meets the ENERGY STAR guidelines for energy efficiency. Mercury Statement (LCD Monitor, LCD Tv, DlP Projection TV, Projector for USA only) Contains Mercury, Dispose According to Local, State or Federal Laws Screws and Guide stand location (Except LED ES 8000 and higher) Product Size LED TV 26"-46" Location -Screws/ Guide-Stand --- --Plasma TV 43"-51" ---- ... Screws/ Guide-Stand -- ----- --LED TV Plasma TV LED 55" Plasma 59" And larger Screws/ Guide-Stand English Screws and guide stand package is placed in the Styrofoam on top. Espaiiol Los tornillos y Guide Stand se encuentran localizados en el Styrofoam superior. Fran~ais Les vis et le paquet du guide du support sont places dans Ia mousse de polystyrene sur le dessus. Top 6 Troubleshooting Tips TV 6 Problemas Principales liiJ TV Handling Guide 1. Can't Connect with Network or Apps (For internet supported model only) 1. No se puede conectar con Ia Red o Apps (Solo para modelos que soporten conexi6n a internet) • Make sure there is a network connection • Asegurese que el equipo este conectado a una red (Menu -7 Network -7 Network status) (Menu -7 Red -7 Estado de Red) • Contact your service provider • Contactar a su proveedor de Internet 2. No Picture/Sound or Distorted Picture/Sound with an External Device • Make sure your connection to the device is correct. • Perform a TV Self Diagnosis to identify the problem (Menu -7 Support -7 Self Diagnosis -7 Sound or Picture Test) • Change the picture size (Use "P. Size" button on your remote) 3. Poor Picture Quality • Verify your signal is High Definition or Standard Definition (Contact your service provider) 2. No hay lmagen/sonido o Distorsi6n de lmagen/sonido con un dispositive externo • Asegure que Ia conexion fisica del dispositive sea correcta • Para identificar el problema, realice un Auto diagnostico en Ia TV (Menu -7 Soporte de Tecnico -7 Autodiagnostico -?Prueba de Imagen o Sonido) • Cambie el tamaiio de Ia imagen (Use el boton "P. Size" del control remota) 3. Mala Calidad de Imagen • Verificar si su seiial es Alta Definicion o Definicion Regular (Contactar a su proveedor de Servicios) 4. Your Settings are Lost after 30 Minutes • Change to Home Mode ("Tools" on your remote -7 Store Demo Off) 4. Su configuracion se pierde despues de 30 minutos • Cambiar a Uso Oomiciliario (Use el bot6n "Tools" del control remota -7 Demo Comercio Desac.) 5. "Weak or No Signal" Displayed in TV Mode/Cannot Find Channel • Press Source button on your remote • Run Auto Program and search for channels (Menu -7 System -7 Plug & Play -7 Enter) 5. "Seiiales Debiles o lnexistentes" Mensaje desplegado en TV Mode I No puede encontrar canales • Presione el baton "Source" en su control remota • Carra Auto Program e inicie busqueda de canales (Menu -7 Sistema -7 Plug & Play -7 Enter) 6. Can't See All Apps or Apps Not Working Reset Smart Hub (fools in main page of Smart Hub -7 Settings -7 Reset Enter with Password, Default Password is 0000) Scan the QR code to view our helpful How-to Videos Escanear el Codigo QR para ver nuestros videos demostrativos de Video Guia Espaiiol Cuando se levante una TV de 55" o mayor, si el dedo pulgar toea Ia pantalla directamente, puede daiiar Ia pantalla. Samsung recomienda que levante Ia TV como se muestra en Ia FIG. Fran<;ais Lorsque vous soulevez un televiseur 55" ou plus, si votre pouce touche directement al' ecran, vous pouvez en dommager l'e cran. Samsung recommande vous soulevez le televiseur, comme indique dans Ia photo. ~ Screen Care Guide 6. No se ven todas las Aplicaciones o no funcionan Resetear Smart Hub (Herramientas en Ia pagina principal de Smart Hub -7 Configuracion -7 Reset lntroducir Ia Contraseiia, Ia Contraseiia Predeterminada es 0000) ~ ~~ English When you lift up a 55" or larger TV, your thumd touches the sareen directly, you can damage the screen. Samsung recommends you lift up the TV as shown in PIC. ~ ~- • • English Do not spray cleaning solutopn directly onto the TV screen. Spray the solution onto a cleaning cloth first, and then clean the screen. Espaiiol No rocie Ia soluci6n de limpieza directamente sabre Ia pantalla del televisor. Rocie Ia soluci6n sabre un paiio de limpieza, y luego limpie Ia pantalla. Fran<;ais Ne pas pulveriser Ia solution de netto yage direnctement sur l'e cran du televiseur. Pulveriser Ia solution sur un chiffon de netto yaged' abord, puis nettoyer l'e cran. For any problem Search helpful video samsung.com/spsn Chat samsung .com/support Call Samsung Support 1-888-899-7604 DO NOT RETURN TO STORE Scan this with your smartphone ">

Public link updated
The public link to your chat has been updated.
Advertisement