dsp color camera
INSTRUCTION MANUAL
DSP COLOR CAMERA
1/3" INTERLINE TRANSFER CCD
STANDARD RESOLUTION
HIGH RESOLUTION
Please read this manual thoroughly before use, and keep it handy for future reference.
ISSUE 1 NOVEMBER 2003
ii
WARNINGS AND CAUTIONS
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO NOT
INSERT ANY METALLIC OBJECTS THROUGH THE VENTILATION
GRILLS OR OTHER OPENINGS ON THE EQUIPMENT.
CAUTION
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER(OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated dangerous voltage
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instruction in the literature accompanying the
product.
iii
FCC COMPLIANCE STATEMENT
FCC INFORMATION : THIS EQUIPMENT HAS BEEN TESTED AND FOUND
TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE,
PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE
DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A
COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES,
AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT INSTALLED
AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY
CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER WILL BE
REQUIRED TO CORRECT THE INTERFERENCE AT HIS OWN EXPENSE.
CAUTION : CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED
BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE
USER'S AUTHORITY TO OPERATE THE EQUIPMENT.
THIS CLASS A DIGITAL APPARATUS COMPLIES WITH CANADIAN ICES-003.
NORME NMB-003 DU CANADA.
iv
IMPORTANT SAFEGUARDS
1. READ AND RETAIN INSTRUCTIONS
Read the instruction manual before operating
the equipment. Retain the manual for future
reference.
9. CORD AND CABLE PROTECTION
Route power cords and cables in a manner to
protect them from damage by being walked on
or pinched by items places upon or against
them.
2. CLEANING
Turn the unit off and unplug from the power
outlet before cleaning. Use a damp cloth for
cleaning. Do not use harsh cleansers or
aerosol cleaners.
10. LIGHTNING
For protection of the equipment during a
lightning storm or when it is left unattended and
unused for long periods of time, unplug the unit
from the wall outlet. Disconnect any antennas
or cable systems that may be connected to the
equipment. This will prevent damage to the
equipment due to lightning or power-line surges.
3. ATTACHMENTS
Do not use attachments unless recommended
by manufactured as they may affect the
functionality of the unit and result in the risk of
fire, electric shock or injury.
11. OVERLOADING
Do not overload wall outlets and extension
cords as this can result in a risk of fire or
electric shock.
4. MOISTURE
Do not use equipment near water or other
liquids.
12. SERVICING
Do not attempt to service the video monitor or
equipment yourself as opening or removing
covers may expose you to dangerous voltage
or other hazards. Refer all servicing to qualified
service personnel.
5. ACCESSORIES
Equipment should be installed in a safe, stable
location. Any wall or shelf mounting accessory
equipment should be installed using the
manufacture's instructions. Care should be
used when moving heavy equipment. Quick
stops, excessive force, and uneven surfaces
may cause the equipment to fall causing serious
injury to persons and objects.
13. DAMAGE REQUIRING SERVICE
Unplug the equipment from the wall outlet and
refer servicing to qualified service personnel
under the following conditions:
6. VENTILATION
Openings in the equipment, if any, are provided
for ventilation to ensure reliable operation of the
unit and to protect if from overheating. These
openings must not be blocked or covered
A. When the power supply cord or the plug has
been damaged.
B. If liquid has spilled or objects have fallen into
the unit.
C. If the equipment has been exposed to water
or other liquids.
D. If the equipment does not operate normally
by following the operating instructions, adjust
only those controls that are covered by the
operating instructions. Improper adjustment
of other controls may result in damage to the
unit.
E. If the equipment has been dropped or the
casing damaged.
F. When the equipment exhibits a distinct
change in performance.
7. POWER SOURCES
The equipment should be operated only from
the type of power source indicated on the
marking label. If you are not sure of the type of
power supplied at the installation location,
contact your dealer. For equipment designed to
operate from battery power, refer to the
operating instructions.
8. GROUNDING OR POLARIZATION
Equipment that is powered through a polarized
plug (a plug with one blade wider than the other)
will fit into the power outlet only one way. This
is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the
plug. Do not defeat the safety purpose of the
polarized plug.
14. REPLACEMENT PARTS
When replacement parts are required, be sure
the service technician uses replacement parts
specified by the manufacturer or that have the
same characteristics as the original part.
Unauthorized substitutions may result in fire,
electric shock, or other hazards.
15. SAFETY CHECK
Upon completion of any service or repairs to the
equipment, ask the service technician to
perform safety checks to verify that the
equipment is in proper operating condition.
Alternate Warning: If the equipment is powered
through a three-way grounding-type plug, a plug
having a third (grounding) pin, the plug will only
fit into a grounding-type power outlet. This is a
safety feature. Do not defeat the safety purpose
of the grounding-type plug. If your outlet does
not have the grounding plug receptacle, contact
your local electrician.
16. FIELD INSTALLATION
The installation of equipment should be made
by a qualified service person and should
conform to all local codes.
v
TABLE OF CONTENTS
INTRODUCTION
1
CAMERA OVERVIEW
2
CONTENTS OF PACKAGE
6
MANUAL IRIS LENS ADJUSTMENT
6
VIDEO-TYPE AUTO-IRIS LENS INSTALLATION
AND ADJUSTMENT
6
DC-TYPE AUTO-IRIS LENS INSTALLATION
AND ADJUSTMENT
8
BACKFOCUS ADJUSTMENT
10
ZOOM LENS BACKFOCUS ADJUSTMENT
11
TROUBLESHOOTING AND MAINTENANCE
12
SPCIFICATIONS
13
vi
ABOUT THE 1/3" DSP COLOR CAMERA
INTRODUCTION
The 1/3" DSP color security camera provides SONY, true-color images
especially for closed-circuit television (CCTV) and security surveillance
applications.
Features:
High-performance 1/3" SONY DSP color CCD technology
320 lines of resolution (Standard)
470 lines of resolution (High)
0.5 lux @ F1.2 sensitivity (Standard)
0.8 lux @ F1.2 sensitivity (High)
C/CS, backfocus cam for easy adjustment
Auto electronic shutter [1/50 ~ 1/100,000] and manual
electronic shutter modes
Auto and manual white balance modes
Compatible with video- or DC-type lenses with dip switch
select
Quick connect for video or DC lens with 4-pin connector
Flicker less, BLC, AGC select(Normal/High), AGC, Sync
adjustments
220-240VAC
IMPORTANT: The user of this camera is
responsible for checking and complying with
local, state, and federal laws and statutes
concerning the recording and monitoring of
audio signals.
1
CAMERA OVERVIEW
SIDE VIEW
C Mount Ring
Back Focus Lock Screw
( C MOUNT LENS )
( CS MOUNT LENS )
Camera Mounting Bracket
Back Focus Ring
BACK VIEW (220 - 240VAC)
Power LED
V. Phase Potentiometer
Level potentiometer
(for DC type A/I lens)
Function
Switch
LEVEL PHASE PWR
LENS
Auto Iris Lens
Connector
220 - 240VAC
AC Power cord
VIDEO OUT
FRONT VIEW
2
Video Out BNC
Connector
1. Back focus Lock Screw
backfocus setting.
Allows the user to secure the
2. C/CS Back focus Adjust Ring Allows the user to adjust the
back focal length or picture focus by rotating this ring clockwise for
C-mount and counter-clockwise for CS-mount lenses.
3. Mounting Bracket Hole This threaded 14"-20 hole is used to mount
the camera onto a mounting bracket or tripod.
4. Iris Adjustment Pot (Potentiometer) This control allows the user
to adjust the level of the auto iris when the A/I lens selection switch
is set to DC and a DC lens is mounted on the camera. The switch
should be in the video position when an auto iris video lens is
mounted on the camera. If a video auto-iris lens is used, this control
has no function.
5. Phase Adjustment This is used in a multi-camera system when
power is supplied from different sources, causing the camera to be
out of phase. This situation affects auto-switching of the cameras by
causing a vertical flip or roll during the switch interval. The vertical
phase adjustment allows the camera's line lock sync to be adjusted
from 0 to 360 degrees with reference to zero line crossing of the AC
power source. Ensure that all cameras are powered from the same
electrical source and wired in a similar fashion. Adjust the phase
control on the back of the camera until there is no vertical flip or roll
on the monitor while using an auto switcher.
6. Power LED This green LED illuminates while power is supplied to
the camera.
7. Auto-iris Lens Connector This four-pin female connector
supplies the power and either video signal or DC control signal to
the auto-iris lens.
8. Function Switches This compartment houses switches for camera
operation. A switch is in the ON position if it is positioned toward the
front of the camera. If the position is set toward the back of the
camera, the switch is OFF. The switches include:
3
SHTR Switch (Aes/Mes) This switch allows the user to choose
between auto exposure and manual exposure. Position the
switch toward the front of the camera for auto exposure, whereby
the exposure is performed by the electronic iris and AGC control.
Position the switch toward the back of the camera for manual
exposure, whereby the shutter speed can be set by the shutter
adjust.
*Manual Exposure (SW1= Manual Exposure)
Switch
SWITCH POSITION
Shutter Speed
SW1
SW2
SW3
SW4
MES
on
on
on
1/50
MES
off
on
on
1/120
MES
on
off
on
1/250
MES
off
off
on
1/500
MES
on
on
off
1/1000
MES
off
on
off
1/2000
MES
on
off
off
1/4000
MES
off
off
off
1/10000
SW1 2 3 4
Flickerless Switch (off/on) (SW1=Auto Exposure) This
function is used for removing flicker, when camera signal format
does not coincide with power source frequency being used.
BLC Switch (on/off) (SW1=Auto Exposure) This on/off switch
controls backlight compensation. When set to ON, the camera
will automatically try to maintain proper exposure in the specific
area even if the lighting level changes.
E/I (on/off) (SW1=Auto Exposure)
When set to the ON position, the electronic iris switch
automatically varies the camera's shutter to mimic auto-iris
control, allowing fixed or manual iris lenses to be used in a wider
range. When this switch is set to ON, turn the F/F switch OFF.
A/I Switch (dc/video) The auto iris switch allows the user to
select the supplied auto-iris control signal for the lens. Position
the switch toward the front of the camera to choose DC when the
auto-iris control lens requires DC control signal. Position the
switch toward the back of the camera to choose Video when the
auto-iris control lens requires video signal.
4
AGC Select Switch (Normal/Hi)
AGC Normal : AGC Middle Gain.
AGC High : AGC Max Gain.
Only AGC Switch (Function, s/w No. 7Pin) ON.
AGC Switch (off/on) The auto gain control switch allows the
video signals to maintain a constant level. This switch is useful
when using the camera at low-light levels and when lighting
levels change over time. For best low light conditions, this
switch should set to ON.
AWB1, AWB2 Switch (on/off) This camera have four white
balance setting.
ATW (auto tracing white balance) The camera automatically
aim to maintain white objects as white even if the light color
changes.
AWB (auto white balance) Quick ATW.
Indoor improves the color balance in areas where a mixture
of light sources exist.
Outdoor Improves the color balance in arrears where day
light is the main source of light.
Switch
SWITCH POSITION
Mode
SW8
SW9
on
on
ATW
on
off
AWB
off
on
Indoor
off
off
Outdoor
SW8 9
Sync Select Switch (int/LL) Use this switch to set the
camera synchronization mode internal (int) or Line Lock (LL).
9. AC Power Cord
1Hz.
This power cord accepts a 220-240V ~ 50Hz +/-
10. Video Out BNC Connector This BNC connector provides a 1.0
Vp-p/75 Ohms composite video signal.
5
CONTENTS OF PACKAGE
Installation of the camera must be performed by qualified service
personnel in accordance with all local and national electrical and
mechanical codes.
Carefully remove the color camera and its accessories from the carton
and verify that they were not damaged in shipment.
The contents of the package includes:
1. Color CCD camera
2. Mini-DIN connector (for video-or dc-type auto-iris lens)
MANUAL IRIS LENS ADJUSTMENT
When using a manual iris lens, turn the iris ring on the lens to the OPEN
position and adjust the manual iris for the appropriate range. Adjust
during the brightest conditions, opening the lens to the minimum f-stop
yielding a good picture under the brightest scene conditions. Do not
saturate the picture.
The manual iris is used in indoor applications where lighting from
windows can considerably affect the light level of the room.
VIDEO AUTO IRIS
INSTALLATION & ADJUSTMENT
The camera supports video-type auto iris lenses which adjust to
changing light levels. Perform the following steps to install and adjust a
video-type auto iris lens.
1. If necessary, solder the lens control wires to the connector supplied
with the camera.
6
Connector
Cover
Rib
Pin 3
Automatic
Iris Lens
Pin 1
Heat
Pin 4
Shrinkable
Tubes
Iris Control
Pin 2
Cable
Connector
PIN
1
2
3
4
NAME
Voltage +
Open
Video
Ground
WIRE COLOR
Red
White
Black
2. Attach the video-type auto iris lens to the lens mount on the front of
the camera.
3. IMPORTANT: The minimum Plug the connector from the lens into
the auto iris jack on the back of the camera. The connector is
polarized and can only be inserted into the jack one way.
4. The E/I switch should be in the OFF position.
5. The A/I switch should be in the VIDEO position.
6. Apply power to the camera.
7. Adjust the focus ring on the lens for an optimum picture. If a picture
is not visible, set the lens for proper exposure by adjusting the ALC
(Automatic Level Control) and the level on the lens. The ALC
setting can range between AVG (average) or PK (peak). A
midrange setting is appropriate for most applications.
For ALC adjustments:
AVG
To slow the reaction of the lens to changing light, set the
range to the AVG setting to average the video level from the
camera. Use when there are bright spots in the picture such
as lights or glare from the sun.
7
PK
To increase the speed of the lens reaction to the changing
light, set the lens adjustment to PK so the lens will adjust to
the brightest or peak object in the video. Use this setting if
you want to see the brightest object and not the background
objects.
For Level adjustments:
Adjust the level control for the best picture during the day. A night
adjustment may not provide the proper setting for controlling the
light during the day.
8. Set the back focus of the camera before the final adjustment of the
video level.
9. If the auto iris has a gain adjustment and the picture oscillates
between open and closed under bright lights, slowly turn the gain
adjustment counter clockwise until the oscillating stops. Increase
the light getting to the camera by adjusting the level control and readjusting the gain control.
DC AUTO IRIS LENS
INSTALLATION & ADJUSTMENT
The camera supports DC-type auto iris lenses. Perform the following
steps to install and adjust a DC-type auto iris lens.
1. Solder the lens control wires to the connector supplied with the
camera.
Connector
Cover
Rib
Pin 3
Automatic
Iris Lens
Pin 1
Heat
Pin 4
Shrinkable
Tubes
Pin 2
Iris Control
Cable
Connector
8
PIN
1
2
3
4
NAME
Damp Coil Damp Coil +
Drive Coil +
Drive Coil -
WIRE COLOR
Blue
Red
White
Green
2. Attach the DC-type auto iris lens to the lens mount on the front of
the camera.
3. Plug the connector into the auto iris jack on the back of the camera.
The connector is polarized and can only be inserted into the jack
one way.
BACK VIEW
4. The E/I switch should be in the "OFF" position.
5. The A/I switch should be in the "DC" position.
6. Apply power to the camera.
7. Adjust the auto iris lens for an optimum picture using the LEVEL
control on the back of the camera.
9
BACK FOCUS ADJUSTMENT
For best results, perform back focus adjustments at night or while using
a #6 or #8 welders glass in front of the lens. The focus of the camera
will change slightly if the camera iris was adjusted on a light scene, then
changes to a dark scene. However, the camera will remain in focus if
the iris was focused on a dark scene and the scene lightens.
1. The lens should be mounted on the camera before applying power.
2. If a picture is visible, focus on the picture. If the picture is not
visible, open the iris on the lens. Open the lens as wide as possible
by placing the welder's glass in front of the lens and forcing the lens
to automatically open.
3. When the iris is open to the widest point, re-adjust the focus for
clear picture. If a clear picture is not possible, set the focus ring to
midrange.
4. Loosen the back focus lock screw.
5. Adjust the back focus ring for a clear picture.
6. Tighten the back focus lock screw.
7. Fine tune the focus with the focus ring on the lens.
8. Remove the welder's glass from in front of the lens.
9. Adjust the iris of the lens for the best picture quality.
10
ZOOM LENS BACK FOCUS ADJUSTMENT
The objective of back focusing a zoom lens is similar to that of a fixed
focal length camera except the back focus is also adjusted to maintain
the focus when zooming the lens in and out on a scene.
1. Choose an object at the farthest range set for viewing with a zoom
lens.
2. Make sure the iris of the lens is wide open. Do this by adjusting the
camera at night or use a welders glass in front of the lens.
3. Adjust the focus to the stop on the far range.
4. Adjust the zoom on the lens to obtain the widest picture.
5. Loosen the back focus lock screw.
6. Adjust the back focus ring for the clearest picture.
7. Tighten the back focus lock screw.
8. Adjust the zoom on the lens to the far telephoto position.
9. Adjust the back focus ring for the clearest picture.
10. Adjust the zoom on the lens back to the widest picture.
11. Loosen the back focus screw.
12. Re-adjust the back focus for the clearest picture.
13. Tighten the back focus lock screw.
14. Repeat the previous steps as necessary to maintain a clear picture
throughout the entire zoom range.
11
TROUBLESHOOTING AND MAINTENANCE
TROUBLESHOOTING
If problems occur, verify the installation of the camera with the
instructions in this manual and with other operating equipment. Isolate
the problem to the specific piece of equipment in the system and refer to
the equipment manual for further information.
PROBLEM
No Video
AREA TO CHECK
1.Verify power is applied to all pieces of the
equipment in the system. The camera LED
should be ON.
2.Verify that the video cables are connected
correctly.
3.Verify that the lens cap has been removed from
the lens and the iris of the lens is open.
Video but no
control
Dark Video
Power down the system for one minute then
re-apply power.
1.Adjust iris.
2.Check A/I connections.
PREVENTIVE MAINTENANCE
Preventive maintenance allows detection and correction of minor faults
before they become serious and cause equipment failures.
Every three months perform the following maintenance:
1. Inspect all connecting cables for deterioration or other damage.
2. Clean components with a clean damp cloth.
3. Verify that all mounting hardware is secure.
12
SPECIFICATIONS
* Standard Resolution DSP Color Camera *
Power
Power Source, Consumption :
Power Indicator :
Sensor Information and General
Processing Technology :
Image Sensor :
Picture Element :
Chip Size :
Unit Cell Size :
Scanning System :
Scanning Frequency :
Sync System :
Vert Phase Adjust Range :
Electronic Shutter :
Operating Temperature / Humidity :
Video
Signal Format :
Resolution :
Minimum Illumination:
Video Output:
Video Iris Output:
S/N Ratio :
BLC Size :
Sync Level :
White Clip :
220 - 240V ~ 50Hz +/-1Hz,
6.0 Watts.
Green LED
Sony DSP
1/3" interline transfer CCD
(sony chip set)
537(H) x 597(V), PAL
5.59mm(H) x 4.68mm(V)
9.8 m(H) x 6.3 m (V), PAL
2:1 Interlace
15.625KHz(H) x 50Hz(V), PAL
Line Lock / Internal
0 deg. To 360 deg.
1/50 ~ 1/100000 sec.
14oF to 122oF (-10oC to +50o C)
/ <96% (non-condensing)
PAL, 625 Lines
PAL, 320TV Lines
0.5 Lux (F1.2)
1.0 Vp-p, 75 Ohms, unbalanced
650mV at video out 1.0 Vp-p
50dB(AGC Off)
40% Center
40 IRE, PAL 300mV
120 IRE, PAL 850mV
13
Function
Auto/Man Shutter Control(E.S.) :
Manual Shutter Control :
Flickerless(F.F) :
BLC :
EI :
Auto Iris Lens :
AGC Select :
AGC :
White Balance :
Sync :
Vert Phase Adjust :
DC Iris Level Adjust :
Connector and Mechanical
Video Output :
Power Input :
AI/DC Output :
Lens Mount :
Mounting Hole :
External Dimensions :
Weight :
Auto(On), Man(Off) (Dip Switch)
1/50, 1/120, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/10,000(Dip
Switch)
ON/OFF (Dip Switch)
ON/OFF (Dip Switch)
ON/OFF (Dip Switch)
DC/Video (Dip Switch)
Normal/High (Dip Switch)
ON/OFF (Dip Switch)
ON/OFF (Dip Switch)
Auto, Quick, Indoor, Outdoor
Internal / Line Lock (Dip Switch)
Adjustable (POT)
Adjustable (POT)
BNC Connector
Power Cord
4-pin mini din jack (Standard
Connection)
C/CS (Selected through back
focus)
1/4" UNC Top and Bottom
2.44W x 2.1H x 5.0D inch
(62W x 54H x 127D mm)
15.51oz (440g)
14
* High Resolution DSP Color Camera *
Power
Power Source, Consumption :
Power Indicator :
Sensor Information and General
Processing Technology :
Image Sensor :
Picture Element :
Chip Size :
Unit Cell Size :
Scanning System :
Scanning Frequency :
Sync System :
Vert Phase Adjust Range :
Electronic Shutter :
Operating Temperature / Humidity :
Video
Signal Format :
Resolution :
Minimum Illumination:
Video Output:
Video Iris Output:
S/N Ratio :
BLC Size :
Sync Level :
White Clip :
220 - 240V ~ 50Hz +/-1Hz,
6.0 Watts.
Green LED
Sony DSP
1/3" interline transfer CCD
(sony chip set)
795(H) x 596(V), PAL
5.59mm(H) x 4.68mm(V)
6.5 m(H) x 6.25 m (V), PAL
2:1 Interlace
15.625KHz(H) x 50Hz(V), PAL
Line Lock / Internal
0 deg. to 360 deg.
1/50 ~ 1/100,000 sec.
14oF to 122oF (-10oC to +50o C)
/ <96% (non-condensing)
PAL, 625 Lines
PAL, 470 TV Lines
0.8 Lux (F1.2)
1.0 Vp-p, 75 Ohms, unbalanced
650mV at video out 1.0 Vp-p
50dB(AGC Off)
40% Center
40 IRE, PAL 300mV
120 IRE, PAL 850mV
15
Function
Auto/Man Shutter Control(E.S.) :
Manual Shutter Control :
Flickerless(F.F) :
BLC :
EI :
Auto Iris Lens :
AGC Select :
AGC :
White Balance :
Sync :
Vert Phase Adjust :
DC Iris Level Adjust :
Connector and Mechanical
Video Output :
Power Input :
AI/DC Output :
Lens Mount :
Mounting Hole :
External Dimensions :
Weight :
Auto(On), Man(Off) (Dip Switch)
1/50, 1/120, 1/250, 1/500, 1/1000,
1/2000, 1/4000, 1/10,000(Dip
Switch)
ON/OFF (Dip Switch)
ON/OFF (Dip Switch)
ON/OFF (Dip Switch)
DC/Video (Dip Switch)
Normal/High (Dip Switch)
ON/OFF (Dip Switch)
ON/OFF (Dip Switch)
Auto, Quick, Indoor, Outdoor
Internal / Line Lock (Dip Switch)
Adjustable (POT)
Adjustable (POT)
BNC Connector
Power Cord
4-pin mini din jack (Standard
Connection)
C/CS (Selected through back
focus)
1/4" UNC Top and Bottom
2.4W x 2.1H x 5.0D inch
(62W x 54H x 127D mm)
15.51 oz (440g)
16
DSP COLOR CAMERA
1/3" INTERLINE TRANSFER CCD
STANDARD RESOLUTION
HIGH RESOLUTION
50301665B
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement