Micron Manual

Add to my manuals
51 Pages

advertisement

Micron Manual | Manualzz

www.onnettechnologies.com

IEEE 802.11b/g/n

WLAN Client Adapter

WLAN 11n WAPI Micro

Dongle

WL-6200-V1

USER’S GUIDE

VERSION 1.0

© All rights reserved.

All trade names are registered trademarks of respective manufacturers listed.

www.onnettechnologies.com

This manual may not be copied in any media or form without the written consent of original maker.

www.onnettechnologies.com

Information To User ... .............................................. ..…….. I

1. Introduction ... ................................................... ...…… 1

2. Wireless LAN Basics ... ........................................... ...……. 3

3. IP ADDRESS ... ....................................................... .……. 4

4. Install Driver/Utility ... ........................................... ..……. 5

4.1 Windows XP/Vista/Win7... .................................... ... 5

5. Wireless Network Configuration ... .................................. ... 7

5.1 Utility Icon ... ....................................................... 7

5.2 Client Mode (Default Setting)... ............................... .. 7

6. Technical Specifications ... .......................................... .. 15

7. Troubleshooting ... .................................................... ... 16

www.onnettechnologies.com

8. Glossary ... ................................................................ . 17

www.onnettechnologies.com

INFORMATION TO USER

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help.

REGULATION INFORMATION

The WLAN 11n USB Client Adapter must be installed and used in strict accordance with the manufacturer’s instructions. This device complies with the following radio frequency and safety standards.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation.

FCC RF Radiation Exposure Statement:

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

Your device contains a low power transmitter. When device is transmitted it sends out Radio

www.onnettechnologies.com

Frequency (RF) signal. Use only with supplied antenna. Unauthorized antenna, modification, or attachments could damage the transmitter and may violate FCC regulations.

You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.

www.onnettechnologies.com

Europe- R&TTE Compliance Statement

Hereby, the company who declares that this equipment complies with the essential requirements and other relevant provisions of DIRECTIVE 1999/5/CE OF THE EUROPEAN PARLIAMENT AND

THE COUNCIL of March 9, 1999 on radio equipment and telecommunication terminal Equipment and the mutual recognition of their conformity (R&TTE).

For the following equipment:

CE Declaration of Conformity

WLAN 11n USB Client Adapter

(Product Name) WLAN 11n USB Client Adapter

(Model Designation) is herewith confirmed to comply with the requirements set out in the Council (European parliament) Directive on the Approximation of the Laws of the Member States relating to

Electromagnetic Compatibility of Radio and Telecom device (1999/5/EC). For the evaluation regarding this Directive, the following standards were applied:

EN 300 328 V1.7.1

EN 301 489-1 V1.8.1 ; EN 301 489-17 V2.1.1

EN 60950-1:2006+A11:2009

This equipment is marked with the

European community. Marking by the symbol symbol and can be used throughout the indicates that usage restrictions apply.

France - 2.4GHz for Metropolitan France:

In all Metropolitan départements, wireless LAN frequencies can be used under the following conditions, either for public or private use:

·

Indoor use: maximum power (EIRP*) of 100 mW for the entire 2400-2483.5 MHz frequency band

·

Outdoor use: maximum power (EIRP*) of 100 mW for the 2400-2454 MHz band and with maximum power (EIRP*) of 10 mW for the 2454-2483 MHz band

Caution: Exposure to Radio Frequency Radiation.

To comply with RF exposure compliance requirements, for mobile configurations, a separation

www.onnettechnologies.com

distance of at least 20 cm must be maintained between the antenna of this device and all persons.

This device is intended for use as check in the following European Community countries:

Austria

Denmark

Germany

Italy

Lithuania

Portugal

Slovakia

Belgium

Estonia

Greece

Iceland

Malta

Poland

Slovenia

Czech Republic

France

Hungary

Luxemburg

Norway

Spain

United Kingdom

Cyprus

Finland

Ireland

Latvia

Netherlands

Sweden

www.onnettechnologies.com

The channel identifiers, channel center frequencies, and regulatory domains of each 22-MHz-wide channel are shown in following Table.

Frequency

Regulatory Domains

Channel

Identifier (MHZ)

Japan ETSI

North

America

1

2

3

4

5

6

7

8

9

10

11

12

13

14

2412

2417

2422

2427

2432

2437

2442

2447

2452

2457

2462

2467

2472

2484

● ●

● ●

● ●

● ●

● ●

France

Israel

Outdoor

● ●

● ●

● ●

● ●

● ●

● ●

● ●

Mexico

www.onnettechnologies.com

Thank you for your purchase of the WLAN Adapter. Featuring wireless technology, this wireless networking solution has been designed for both large and small businesses, and it is scalable so that you can easily add more users and new network features depending on your business scale.

FEATURES

Support Microsoft XP(32bit/64bit) / Vista(32bit/64bit) / Win7(32bit/64bit).

Operating distance of up to 300 meters in free space.

150/120/90/60/54/48/36/30/24/22/18/12/11/6/5.5/2/1 Mbps selectable Data

Rate.

64/128-bit WEP , WPA (Wi-Fi Protected Access), WPA2

2.400GHz ~ 2.4835GHz unlicensed ISM Frequency Band.

Modulation Method :

IEEE 802.11b : DSSS (Direct Sequence Spread Spectrum).

IEEE 802.11g / 802.11n : OFDM (Orthogonal Frequency Division

Multiplexing). Easy operation and setting up.

SYSTEM REQUIREMENTS

Windows System : XP(32bit/64bit) / Vista(32bit/64bit) / Win7(32bit/64bit).

www.onnettechnologies.com

PCs must have a device driver installed. It allows you to communicate with

WLAN 11n USB Client Adapter.

1

www.onnettechnologies.com

BEFORE YOU START

1. Confirm Box Contents

WLAN 11n USB Client Adapter

Quick Start Guide

Driver CD

CONNECTING YOUR WLAN 11n USB Client Adapter TO PC

Quick Start Guide

Connect your WLAN 11n USB Client Adapter to your PC. Install driver.

GETTING TO KNOW WIRELESS LAN ADAPTER

LED

LED turns on when WLAN link to WLAN adaptor or AP.

LED is blinking when WLAN Adapter is active.

www.onnettechnologies.com

2

www.onnettechnologies.com

Wireless LAN network defined by IEEE 802.11b/g standard committee could be configured as :

Ad Hoc wireless LAN.

Infrastructure wireless LAN.

Ad Hoc network is a group of PCs installed with wireless LAN cards, this

group of PCs is called a BSS (Basic Service Set). PCs in this group can use their wireless LAN cards to communicate with each other, but can not connect to the Internet.

Ad Hoc

Wireless Network

Infrastructure

Wireless Network

The most obvious difference between Infrastructure wireless network and Ad Hoc wireless network is that the PCs in Infrastructure wireless

www.onnettechnologies.com

network can access the resource in the Internet through Access Point.

Depending on your requirement, you can easily set up your PC’s network to be a “Ad Hoc” or “Infrastructure” wireless network. Generally speaking, if in your network, there is an Access Point in it, we recommend you to set your network as an “Infrastructure”, so it can connect to the Internet.

3

www.onnettechnologies.com

To use the WLAN 11n USB Client Adapter with a computing device, the WLAN

Adapter must be equipped with a proper Interface. All drivers and supporting software for the WLAN Adapter must be installed and configured first.

Ask your system administrator for the following information, which you may need to provide during driver installation :

Your Wireless Client

Name. Your Wireless

SSID.

Your computer’s unique client name and workgroup name. For your network account, your user name and password.

Your IP address, gateway address, and subnet mask if you’re not using a DHCP client.

Any computer on a network is identified by a unique network address. There are two methods to assign a network address to a computer on a TCP/IP network :

Static IP addressing.

Dynamic IP addressing (DHCP Client).

www.onnettechnologies.com

In network with static IP addressing, the network administrator manually assigns an IP address to each computer. Once a static IP address is assigned, a computer uses the same IP address every time it reboots and logs on to the network. You may manually change the

IP address in the

Network Properties dialog box.

Network using static IP address is easy to set up and do not require additional network management software.

In network with dynamic IP addressing, a DHCP server in the network dynamically assigns IP addresses to all clients every time they log on to the network. Network using dynamic IP address requires setting up and running a DHCP Server.

4

www.onnettechnologies.com

The installation

& driver CD will automatically activate the autorun installation program after you insert the disk into your CD drive.

Step 1 :

Insert the installation CD into your

CD-ROM. Choose the Setup

Language and click

Next

button.

Step 2 :

Installation descriptions shown. Click

Next

to continue.

www.onnettechnologies.com

Click

Install

to begin the installation

5

www.onnettechnologies.com

Installing & configuring WLAN utility

Installing Drivers.

Step 3 :

Click

Finish

to complete installation

www.onnettechnologies.com

6

www.onnettechnologies.com

WLAN 11n USB Client Adapter uses its own management software. All functions controlled by users are provided by this application. When you insert the WLAN Adapter into your laptop or desktop, a icon should appear in the

Windows System Tray automatically.

5.1 Utility Icon

Client mode utility running but no WLAN Adapter plugged

Client mode utility running and WLAN Adapter scan available network.

Client mode utility running and WLAN Adapter can not scan any AP

AP mode utility running.

5.2 Client Mode (Default Setting)

www.onnettechnologies.com

Wireless Device Control :

Show Tray Icon - Show icon or not show icon in systray.

Radio Off - Stop wireless signal.

Disable Adapter - Stop wireless device.

7

www.onnettechnologies.com

5.2.1 GENERAL SETTING

Once device is set, double click on that icon and the configuration window will pop up as shown. It shows the current connected network.

The signal strength and link quality are displayed also.

The bar graph displays the quality and strength of the link between the node and its Access Point. Link Quality is a measurement of receiving and transmitting performances over the radio.

Network Address

displays current MAC Address, IP Address,

Subnet. and Gateway.

Click

Renew IP

button to refresh IP address leased from wireless

AP.

5.2.2 PROFILE SETTING

In profile tab, you can

Add

,

Remove

,

Edit

,

Duplicate

and

Set Default

to

www.onnettechnologies.com

manipulate profile content manually. Strongly recommend to use profile after you do

Available

Network

.

8

www.onnettechnologies.com

5.2.3 AVAILABLE NETWOEK SETTING

Click

Available Network

tab and it will show all available networks that radio can reaches. Select proper

SSID & BSSID you want to connect.

Click

Refresh

button to force and rescan available networks currently.

Select one of SSIDs, and click

Add to Profile

to create profile that can be configured more wireless parameters.

In this page, you can edit your profile name, configure wireless security like WEP, WPA, WPA2,

802.1x …etc. After finishing setup, click

OK

button to save configuration

www.onnettechnologies.com

5.2.4 Status

Status page tab, shows all wireless, networking and device driver version in details.

9

www.onnettechnologies.com

5.2.5 Statistics

Statistics page tab will show real-time TX/RX relative counters to check or evaluate the wireless performance.

Click

Reset

button to set counter to zero.

5.2.6 Wi-Fi Protected Setup

An easy and secure setup solution for Wi-Fi network. you can choose PIN Code or

Push Button method to connect to an AP.

www.onnettechnologies.com

Pin method:

Step 1 :

Push the PIN button.

10

www.onnettechnologies.com

Step 2 :

Select a specific AP

Step 3 :

Enter the PIN code into your AP.

Step 3 :

Select AP that you want to configure.

www.onnettechnologies.com

Step 4 :

Wait for configuring your wireless AP to be the security setting.

11

www.onnettechnologies.com

PBC method:

Step 1 :

Push the PBC button.

Step 2 :

Push the physical button on your AP or visual button on the WPS config page.

www.onnettechnologies.com

Soft AP:

Step 1 :

Click Access Point to change AP mode

12

www.onnettechnologies.com

Step 2 :

Click Config to set AP.

Step 3 :

Setting SSID and Securtiy

www.onnettechnologies.com

Step 4 :

Choosing the Ethernet controller and click Apply to bridge your

Soft AP.

13

www.onnettechnologies.com

Model Name

Product Name

Standard

Data Transfer Rate

Modulation Method

Frequency Band

Spread Spectrum

WL-6200-V1

WLAN 11n USB Adapter (1T1R)

802.11b/g/n, 802.3, 802.3u

1,2,5.5,6,11,12,18,22,24,30,36,48,54,60,90,120 and maximum of 150Mbps

BPSK/ QPSK/ 16-QAM/ 64-QAM

2.4GHz ISM Band

IEEE 802.11b: DSSS (Direct Sequence Spread Spectrum)

IEEE 802.11g/n:OFDM (Orthogonal Frequency Division

Multiplexing)

RF Output Power

Operation Mode

Receiver Sensitivity

< 12dBm@11n,< 17dBm@11b,< 15dBm@11g

Ad hoc, Infrastructure

11Mbps -80dBm@8%, 54Mbps -70dBm@10%, 130Mbps -

64dBm@10%

Operation Range

LED

OS Support

Security

Interface

Power Consumption

Up to 180m in open space

Power

Windows XP /Vista / 7

WEP, TKIP, AES, WPA and WPA2

USB 2.0

Transmit: average 305 mA

Receive: average 190 mA

Operating Temperature 0 - 60° C ambient temperature

Storage Temperature -20 ~ 70°C ambient temperature

Humidity 0 to 95 % maximum (non-condensing)

Dimension

www.onnettechnologies.com

23x16x8mm (LxWxH)

14

www.onnettechnologies.com

Symptom :

The LED is off.

Remedy :

Make sure the PC Card is inserted properly. Otherwise contact your vendor.

Symptom :

The LED is always on not blinking.

Remedy :

Make sure that you have installed the driver from attached CD. Otherwise contact your vendor.

Symptom :

The LED is blinking but the PC Card icon does not appear in your icon tray.

Remedy :

Make sure that you have installed the Utility from the attached CD.

Symptom :

The PC Card is linking, but can’t share files with others.

Remedy :

Make sure the file and printer sharing function is enabled. You can

www.onnettechnologies.com

enable the function by checking the icon of My Computer -> Control

Panel -> Network -> file and printer sharing -> I want to be able to give

others to access to my files.

Symptom :

Slow or poor performance under AP mode

Remedy :

Try to select another channel for the communicating group or move your device closer to the Access Point.

15

www.onnettechnologies.com

IEEE 802.11 Standard

The IEEE 802.11 Wireless LAN standards subcommittee, which is formulating a standard for the industry.

Access Point

An internetworking device that seamlessly connects wired and wireless networks together.

Ad Hoc

An Ad Hoc wireless LAN is a group of computers, each with a WLAN adapter, connected as an independent wireless LAN. Ad Hoc wireless LAN is applicable at a departmental scale for a branch or SOHO operation.

BSSID

A specific Ad Hoc LAN is called a Basic Service Set (BSS). Computers in a

BSS must be configured with the same BSSID.

DHCP

Dynamic Host Configuration Protocol - a method in which IP addresses are assigned by server dynamically to clients on the network. DHCP is used for

Dynamic IP Addressing and requires a dedicated DHCP server on the network.

Direct Sequence Spread Spectrum

This is the method the wireless cards use to transmit data over the frequency spectrum. The other method is frequency hopping. Direct sequence

www.onnettechnologies.com

spreads the data over one frequency range (channel) while frequency hopping jumps from one narrow frequency band to another many times per second.

ESSID

An Infrastructure configuration could also support roaming capability for mobile workers. More than one BSS can be configured as an Extended

Service Set (ESS). Users within an ESS could roam freely between BSSs while served as a continuous connection to the network wireless stations and

Access Points within an ESS must be configured with the same ESSID and the same radio channel.

Ethernet

Ethernet is a 10/100Mbps network that runs over dedicated home/office wiring. Users must be wired to the network at all times to gain access.

Gateway

A gateway is a hardware and software device that connects two dissimilar

16

www.onnettechnologies.com

systems, such as a LAN and a mainframe. In Internet terminology, a gateway is another name for a router. Generally a gateway is used as a funnel for all traffic to the Internet.

IEEE

Institute of Electrical and Electronics Engineers

Infrastructure

An integrated wireless and wired LAN is called an Infrastructure configuration. Infrastructure is applicable to enterprise scale for wireless access to central database, or wireless application for mobile workers.

ISM Band

The FCC and their counterparts outside of the U.S. have set aside bandwidth for unlicensed use in the so-called ISM (Industrial, Scientific and

Medical) band. Spectrum in the vicinity of 2.4 GHz, in particular, is being made available worldwide. This presents a truly revolutionary opportunity to place convenient high-speed wireless capabilities in the hands of users around the globe.

Local Area Network (LAN)

A LAN is a group of computers, each equipped with the appropriate network adapter card connected by cable/air, that share applications, data, and peripherals. All connections are made via cable or wireless media, but a LAN does not use telephone services. It typically spans a single building or campus.

Network

A network is a system of computers that is connected. Data, files, and

www.onnettechnologies.com

messages can be transmitted over this network. Networks may be local or wide area networks.

Protocol

A protocol is a standardized set of rules that specify how a conversation is to take place, including the format, timing, sequencing and/ or error checking.

SSID

A Network ID unique to a network. Only clients and Access Points that share the same SSID are able to communicate with each other. This string is case-sensitive.

Static IP Addressing

A method of assigning IP addresses to clients on the network. In networks with Static IP address, the network administrator manually assigns an IP address to each computer. Once a Static IP address is assigned, a computer

17

www.onnettechnologies.com

uses the same IP address every time it reboots and logs on to the network, unless it is manually changed.

Temporal Key Integrity Protocol (TKIP)

The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the

IEEE 802.11i encryption standard for wireless LANs. TKIP is the next generation of WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless LANs. TKIP provides per-packet key mixing, a message integrity check and a re-keying mechanism, thus fixing the flaws of WEP.

Transmission Control Protocol / Internet Protocol (TCP/IP)

TCP/IP is the protocol suite developed by the Advanced Research

Projects Agency (ARPA). It is widely used in corporate Internet works, because of its superior design for WANs. TCP governs how packet is sequenced for transmission the network. The term “TCP/IP” is often used generically to refer to the entire suite of related protocols.

Transmit / Receive

The wireless throughput in Bytes per second averaged over two seconds.

Wi-Fi Alliance

The Wi-Fi Alliance is a nonprofit international association formed in 1999 to certify interoperability of wireless Local Area Network products based on

IEEE 802.11 specification. The goal of the Wi-Fi Alliance’s members is to enhance the user experience through product interoperability. The organization is formerly known as WECA.

Wi-Fi Protected Access (WPA)

www.onnettechnologies.com

The Wi-Fi Alliance put together WPA as a data encryption method for

802.11 wireless LANs. WPA is an industry-supported, pre-standard version of

802.11i utilizing the Temporal Key Integrity Protocol (TKIP), which fixes the problems of WEP, including using dynamic keys.

Wide Area Network (WAN)

A WAN consists of multiple LANs that are tied together via telephone services and / or fiber optic cabling. WANs may span a city, a state, a country, or even the world.

Wired Equivalent Privacy (WEP)

Now widely recognized as flawed, WEP was a data encryption method used to protect the transmission between 802.11 wireless clients and

APs. However, it used the same key among all communicating devices.

WEP’s problems are well-known, including an insufficient key length and no automated method for distributing the keys. WEP can be easily

18

www.onnettechnologies.com

cracked in a couple of hours with off-the-shelf tools.

Wireless LAN (WLAN)

A wireless LAN does not use cable to transmit signals, but rather uses radio or infrared to transmit packets through the air. Radio Frequency

(RF) and infrared are the commonly used types of wireless transmission.

Most wireless LANs use spread spectrum technology. It offers limited bandwidth, usually under 11Mbps, and users share the bandwidth with other devices in the spectrum; however, users can operate a spread spectrum device without licensing from the Federal Communications

Commission (FCC).

Fragment Threshold

The proposed protocol uses the frame fragmentation mechanism defined in

IEEE 802.11 to achieve parallel transmissions. A large data frame is fragmented into several fragments each of size equal to fragment threshold.

By tuning the fragment threshold value, we can get varying fragment sizes.

The determination of an efficient fragment threshold is an important issue in this scheme. If the fragment threshold is small, the overlap part of the master and parallel transmissions is large. This means the spatial reuse ratio of parallel transmissions is high. In contrast, with a large fragment threshold, the overlap is small and the spatial reuse ratio is low. However high fragment threshold leads to low fragment overhead. Hence there is a trade-off between spatial re-use and fragment overhead.

Fragment threshold is the maximum packet size used for fragmentation.

www.onnettechnologies.com

Packets larger than the size programmed in this field will be fragmented If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may want to try lowering your fragmentation threshold. This will cause packets to be broken into smaller fragments. These small fragments, if corrupted, can be resent faster than a larger fragment.

Fragmentation increases overhead, so you'll want to keep this value as close to the maximum value as possible.

RTS (Request To Send) Threshold

The RTS threshold is the packet size at which packet transmission is governed by the RTS/CTS transaction. The IEEE 802.11-1997 standard allows for short packets to be transmitted without RTS/CTS transactions. Each station can have a different RTS threshold. RTS/CTS is used when the data packet size exceeds the defined RTS threshold. With the CSMA/CA transmission

19

www.onnettechnologies.com

mechanism, the transmitting station sends out an RTS packet to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before sending the actual packet data. This setting is useful for networks with many clients. With many clients, and a high network load, there will be many more collisions. By lowering the RTS threshold, there may be fewer collisions, and performance should improve. Basically, with a faster RTS threshold, the system can recover from problems faster. RTS packets consume valuable bandwidth, however, so setting this value too low will limit performance.

Beacon Interval

In addition to data frames that carry information from higher layers, 802.11 includes management and control frames that support data transfer. The beacon frame, which is a type of management frame, provides the "heartbeat" of a wireless LAN, enabling stations to establish and maintain communications in an orderly fashion. Beacon Interval represents the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon

(and learn whether there are buffered frames at the access point).

Preamble Type

There are two preamble types defined in IEEE 802.11 specification. A long preamble basically gives the decoder more time to process the preamble. All

802.11 devices support a long preamble. The short preamble is designed to

www.onnettechnologies.com

improve efficiency (for example, for VoIP systems). The difference between the two is in the Synchronization field. The long preamble is 128 bits, and theshort is 56 bits.

WPA2

It is the second generation of WPA. WPA2 is based on the final IEEE 802.11i amendment to the 802.11 standard.

Temporal Key Integrity Protocol (TKIP)

The Temporal Key Integrity Protocol, pronounced tee-kip, is part of the IEEE

802.11i encryption standard for wireless LANs. TKIP is the next generation of

WEP, the Wired Equivalency Protocol, which is used to secure 802.11 wireless

LANs. TKIP provides per-packet key mixing, a message integrity check and a rekeying mechanism, thus fixing the flaws of WEP.

20

www.onnettechnologies.com

802.1x Authentication

802.1x is a framework for authenticated MAC-level access control, defines

Extensible Authentication Protocol (EAP) over LANs (WAPOL). The standard encapsulates and leverages much of EAP, which was defined for dial-up authentication with Point-to-Point Protocol in RFC 2284.

Beyond encapsulating EAP packets, the 802.1x standard also defines EAPOL messages that convey the shared key information critical for wireless security.

Advanced Encryption Standard (AES)

Security issues are a major concern for wireless LANs, AES is the U.S. government’s next-generation cryptography algorithm, which will replace DES and 3DES.

www.onnettechnologies.com

21

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement