advertisement
harman/kardon
HKTS 10
Home Cinema Speaker System
SERVICE MANUAL
harman/kardon, Inc.
250 Crossways Park Dr.
Woodbury, New York 11797 Rev0 8/2002
CONTENTS
SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . .. . . . . . . . . .. .. . .. . . . . .. .. . . . . . . . 1
SPECIFICATIONS
HKTS 10 System Frequency Response 35Hz – 20kHz (–6dB)
SAT-TS10 Satellites
Recommended Power
10 – 110 watts
Impedance
8 ohms nominal
Sensitivity
86dB @ 1 watt/1 meter
Tweeter
One 1" dome, videoshielded
Midrange
One 4" driver, videoshielded
Dimensions (H x W x D)
10-1/8" x 5-1/4" x 5-3/8"
257mm x 133mm x 137mm
Weight
6.6 lb/3.0kg
CEN-TS10 Center
Recommended Power
10 – 110 watts
Impedance
8 ohms nominal
Sensitivity
86dB @ 1 watt/1 meter
Tweeter
One 1" dome, video-shielded
Midrange
Dual 4" drivers, videoshielded
Dimensions (H x W x D)
5-1/16" x 16-1/2" x 5-3/16"
128mm x 418mm x 131mm
Weight
10 lb/4.5kg
SUB-TS10 Subwoofer
Amplifier
150 watts RMS
Bass Driver
12" woofer, bass-reflex enclosure
Dimensions (H x W x D)
20-5/16" x 16-3/8" x 15-1/16"
515mm x 416mm x 382mm
Weight
40 lb/18.0kg
Occasional refinements may be made to existing products without notice but will always meet or exceed original specifications unless otherwise stated.
1
HKTS 10 harman/kardon
SUB-TS10
LINE VOLTAGE
US 120vac/60Hz
150W Powered Amplifier
Yes/No
Yes
Hi/Lo Line
108-132 Vrms
Unit
Notes
Normal Operation
Parameter
Amp Section
Type (Class AB, D, other)
Load Impedance (speaker)
Rated Output Power
THD@ Rated Power
THD @ 1 Watt
DC Offset
Damping factor
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
Speaker/Hi Level Input
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
Residual Noise Floor
Specification Unit
D D
4 Ohms
150 Watts
0.08 %
0.15 %
5 mV-DC
>100 DF
50 Hz
220 mVrms
220 mVrms
2.2 Vrms
100 dBA
90 dBr
65 dBr
1.2 mVrms
0.8
mVrms(max)
Residual Noise Floor
Input Impedance
Line input L&R , LFE
Speaker/Hi Level Input
Filters
Left & Right Low Pass fixed
LFE Low Pass fixed
Subsonic filter (HPF)
Limiter
Features
LFE Input
Volume pot Taper (lin/log)
ATO
Signal Sensing (ATO)
ATO test Frequency
ATO Line Level
ATO Speaker level input
ATO Turn-on time
Auto Mute/ Turn-OFF Time
Power on Delay time
Transients/Pops
ATO Transient
Turn-on Transient
Turn-off Transient
Efficiency
10 K ohms
4.7 K ohms
130 Hz
220 Hz
22 Hz
YES
YES log
YES
50 Hz
4.0 mV
40 mV
5 ms
15 minutes
3 sec.
--
--
--
--
--
5 mV-peak
50 mV-peak
50 mV-peak
QA Test Limits Conditions
n/a n/a
150
1
0.5
30
30
Nominal
1 input driven
22k filter
22k filter
@ Speaker Outputs
NA
±2dB
±2dB
±2dB
85
80
60
3.0
2.0
n/a n/a
±2dB
±2dB
±2dB n/a functional functional functional n/a
2.0 - 8.0
20 - 80 functional
10 - 25 functional
10
100
100
Nominal Freq.
To Rated Power
To Rated Power
To Rated Power rel. to rated power rel. to rated power rel. to 1W Output
Volume @max, using RMS reading
DMM/VOM (or A/P)
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
Nominal
Nominal
@ -3dB ref. 100Hz
@ -3dB ref. 100Hz
@ -3dB ref. 100Hz driven
Amp connected and AC on, then input signal applied
T before muting, after signal is removed
AC Power Applied
@ Speaker Outputs
@ Speaker Outputs
@ Speaker Outputs
Notes
Measured at speaker terminals, Output power
140 Watts THD 0.1 %
1 input driven
1 input driven
LFE input driven only
(-20 dB below Line In)...1 input driven
A-Weighting filter
22k filter
22k filter
BW Limited to 220 Hz
AC Line cycled from OFF to ON
AC Line cycled from ON to OFF
10 Watts
230 Watts
12
250
@ nom. line voltage
@ nom. line voltage
Maximum allowable input power under nominal Input voltage and frequency, HOT or
COLD operation.
150 Watts @ 4 Ohms nominal line voltage
Stand-by Input Power
Power Cons.@rated power
Protection
Short Circuit Protection
Thermal Protection
DC Offset Protection
Line Fuse Rating
US Version
YES
65 deg. C
YES
3.15 Amps
--
--
-functional functional functional
Direct short at output
@1/8 max unclipped Power
DC present at Speaker Out leads
Type-T or Slo Blo
Temperature rise should not exceed 35K rise
Relay or crowbar (for driver/fire protection)
External fuse with UL/SEMKO rated holder
2
HKTS 10 harman/kardon
SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
™
¡
¢
£
∞
§
¶ ª
R L
LINE
LEVEL
IN
OFF
FILTER
ON
FILTER
REMOTE
CONTROL
SUB
L
GREEN: ON
RED: STAND-BY
PHASE
R
NORMAL REVERSE ON AUTO
IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.
SUBW OOFER LEVEL
‚
SUB-TS10 For use with
HKTS 10 System harman/kardon
Made in China
POWER
AC 120V~60Hz
⁄
¤
¡ Speaker-Level Inputs
™ Speaker-Level Outputs
£ Line-Level Subwoofer (SUB) Input
¢ Line-Level Full-Range Inputs
∞ Phase Switch
§ High-Cut (Low-Pass) Filter Switch
¶ Music-Sense On/Off Switch
• Filter Remote Control Input
ª LED Indicator
‚ Subwoofer-Level Control
⁄ Master Power Switch
¤ AC Power Cord
¡ Speaker-Level Inputs: Connect these binding post terminals to the main left and right speaker terminals of your receiver or amplifier, if your receiver or amplifier does not have a line-level subwoofer output.
Remember to maintain polarity by connecting the (+) terminal on the receiver/amplifier to the (+) terminal on the SUB-TS10 subwoofer, and the (–) terminal on the receiver/amplifier to the (–) terminal on the SUB-TS10 subwoofer.
™ Speaker-Level Outputs: If you are using the Speaker-Level Inputs ¡ on the SUB-TS10, you should connect these binding post terminals to your front left and right speakers, remembering to maintain polarity by connecting the (+) terminal on the SUB-TS10 subwoofer to the (+) terminal on the speaker, and the (–) terminal on the SUB-TS10 subwoofer to the (–) terminal on the speaker. If you are not using the
Speaker-Level Inputs ¡, then connect your front left and right speakers directly to your receiver or amplifier. See pages 6 and
7 for further information.
£ Line-Level Subwoofer (SUB) Input:
Connect the subwoofer output of a receiver with digital surround sound decoding, such as Dolby* Digital or DTS ® , to this input. This input bypasses the SUB-TS10’s internal crossover circuitry, and should only be used with a filtered signal. If your receiver does not have digital decoding, you should use the
Line-Level Full-Range Inputs ¢ instead.
¢ Line-Level Full-Range Inputs: Connect the line-level subwoofer output or preamp output(s) of your receiver or amplifier to these inputs. If your receiver does not have a separate subwoofer output, use a Y-adaptor
(not supplied) to bridge the receiver’s preamp output to the main amp input for that channel, and connect the long end of the adaptor to the corresponding line-level input on the
SUB-TS10. If your receiver has only a single subwoofer output, you may connect it to either the left or right line-level input on the
SUB-TS10, and no Y-adaptor is needed.
∞ Phase Switch: This switch determines whether the SUB-TS10 subwoofer’s piston-
3
HKTS 10 harman/kardon
SUB-TS10 SUBWOOFER AMPLIFIER PANEL CONTROLS AND CONNECTIONS
like action moves in and out in phase with the main speakers. If the speakers were to play out of phase, the sound waves produced by the subwoofer would be cancelled out, reducing bass response. This phenomenon depends in part on the relative placement of the speakers in the room. In most cases, the Phase Switch ∞ should be left in the NORMAL position. However, it does no harm to experiment with the
Phase Switch ∞, and you may leave it in the position that maximizes bass response.
§ High-Cut (Low-Pass) Filter Switch:
Placing this switch in the ON position activates circuitry that cuts out all audio input signals above 120Hz. This allows the SUB-
TS10 to focus its power on reproducing the low-frequency portion of the signal, avoiding inefficiency and distortion. Engage this filter when using the Speaker-Level
Inputs ¡, or when using the Line-Level
Full-Range Inputs ¢, unless your receiver or processor processes its line-level output using a low-pass filter. The filter has no effect when the SUB Input £ is used.
¶ Music-Sense On/Off Switch: When placed in the AUTO position, and when the
Master Power Switch ⁄ is turned on, the
SUB-TS10 will automatically turn itself on or place itself in the Standby mode, depending on whether it is receiving an audio signal.
When this switch is placed in the ON position, the SUB-TS10 will remain on, whether or not it is receiving an audio signal.
• Filter Remote Control Input: This input accepts a remote control signal from a compatible Harman Kardon A/V receiver that enables you to override the High-Cut
(Low-Pass) Filter Switch §, by signaling the SUB-TS10 to engage the filter even when the switch is in the OFF position.
ª LED Indicator: This LED indicates whether the SUB-TS10 is in the ON or
STANDBY state when used with the
Music-Sense On/Off Switch ¶ in the
AUTO position. The LED is lit Green to indicate that the SUB-TS10 is receiving an audio signal and is turned on, and the
LED is lit Red to indicate that no signal is being received and the SUB-TS10 is in
Standby mode.
When the Music-Sense On/Off Switch
¶ is in the ON position, the LED will be lit
Green, whether or not an audio signal is present.
When the Master Power Switch ⁄ is turned off, the LED goes dark, no matter which position the Music-Sense On/Off
Switch ¶ is in.
‚ Subwoofer-Level Control: Volume can be adjusted using the Subwoofer-
Level Control. Turn the control clockwise to increase the SUB-TS10’s volume, or counterclockwise to decrease it.
⁄ Master Power Switch: Place this switch in the “•” position to power-on the
SUB-TS10 subwoofer. The SUB-TS10 will then be either in the Standby mode or completely on, depending on the position of the Music-Sense On/Off Switch ¶.
¤ AC Power Cord: Make sure to plug this cord into an active, unswitched electrical outlet for proper operation of the SUB-
TS10. The cord should not be plugged into the accessory outlets found on some audio components.
4
HKTS 10
SPEAKER CONNECTIONS (continued)
Dolby Digital or DTS (or other
Digital Surround Mode)
Connection
USE THIS INSTALLATION METHOD FOR
DOLBY DIGITAL, DTS OR OTHER DIGITAL
SURROUND PROCESSORS:
Use the line-level input jack marked SUB
£ for the Low-Frequency Effects channel.
Connect this jack to the subwoofer output or LFE output on your receiver or amplifier.
Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.
Make sure that you have configured your surround sound processor for “Subwoofer
On.” The front left, front right, center and rear surround speakers should all be set to
“Small.”
When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Front
Left
– +
Surround
Left
– +
harman/kardon
Center
– +
LINE
LEVEL
IN
SUB
R
L
Front
Left
Surround
Left
Front
Right
SUB/LFE
Out
Center
Surround
Right
Receiver
Front
Right
– +
Surround
Right
– +
5
HKTS 10
SPEAKER CONNECTIONS (continued)
Dolby Pro Logic
(Non-Digital) – Line Level
USE THIS INSTALLATION METHOD FOR
DOLBY PRO LOGIC APPLICATIONS (NOT
DOLBY DIGITAL, DTS OR OTHER DIGITAL
PROCESSING), WHERE THE RECEIVER/
PROCESSOR IS EQUIPPED WITH A SUB-
WOOFER OUTPUT, OR A VOLUME-
CONTROLLED PREAMP (LINE-) LEVEL
OUTPUT:
Use the supplied RCA-type patch cord to connect the line-level subwoofer output on your receiver or amplifier to either the left or right Line-Level Full-Range Input ¢ on the SUB-TS10 subwoofer. Use both the left and right inputs on the subwoofer if your receiver or processor has both left and right line-level outputs.
If your receiver is equipped with line-level outputs but does not have a separate subwoofer output, use a Y-adaptor (not supplied) to bridge the receiver’s preamp output to the main amp input for that channel, and connect the long end of the adaptor to the corresponding line-level input on the SUB-TS10.
IMPORTANT: Do not use the SUB Input £ on the subwoofer with Dolby Pro Logic processors. Make sure that you have configured your surround sound processor for
“Subwoofer On.” The front left, front right, center and rear surround speakers should all be set to “Small.”
When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Connect each speaker to the corresponding speaker terminals on your receiver or amplifier.
Front
Left
– +
Surround
Left
– +
Center
– +
SUB-TS10
Subwoofer
Line-Level
L
R
Front
Left
Surround
Left
Front
Right
SUB/LFE
Out
Center
Surround
Right
Receiver
harman/kardon
Front
Right
– +
Surround
Right
– +
6
HKTS 10 harman/kardon
SPEAKER CONNECTIONS (continued)
Dolby Pro Logic*
(Non-Digital) – Speaker Level
USE THIS INSTALLATION METHOD FOR
DOLBY PRO LOGIC APPLICATIONS (NOT
DOLBY DIGITAL, DTS OR OTHER DIGITAL
PROCESSING), WHERE THE RECEIVER/
PROCESSOR DOES NOT HAVE A SUB-
WOOFER OUTPUT, OR A VOLUME-
CONTROLLED PREAMP (LINE-) LEVEL
OUTPUT:
Connect your receiver or amplifier’s front left and right speaker terminals to the left and right Speaker-Level Input ¡ terminals on the SUB-TS10 subwoofer that are marked “High Level In.” Connect the left and right Speaker-Level Output ™ terminals on the SUB-TS10 subwoofer that are marked “High Level Out” to the corresponding terminals on the back of your front left and right speakers.
Connect your receiver or amplifier’s center, and surround left and right speaker terminals to the corresponding terminals on the back of your center, and surround left and right speakers.
When all connections have been made, plug the AC power cord on the subwoofer into an AC outlet.
Front Left
– +
Front Left
Surround Left
Center
– +
R
SUB-TS10
Subwoofer
L
Receiver
Center
Front Right
Surround Right
Front Right
– +
Surround Left
– +
Surround Right
– +
7
HKTS 10 harman/kardon
OPERATION
Move the Master Power Switch ⁄
(marked Power) to the “
•
” (On) position.
The SUB-TS10 subwoofer will automatically turn itself on or go into Standby mode, depending on whether or not a signal is being sent to it by your receiver or surround processor, and provided that the Music-
Sense On/Off Switch ¶ is moved to the right so that it is in the AUTO position.
When your receiver or amplifier is off, or is not sending program material to the subwoofer, the subwoofer will be in Standby mode and the LED Indicator ª on the amp panel will turn red. When the subwoofer senses an audio signal, it will automatically turn itself on and the LED
Indicator ª will turn green. If the subwoofer does not sense a signal after approximately twenty minutes, it will automatically go into Standby mode.
When the Music-Sense On/Off Switch
¶ is switched to the ON position, the subwoofer will remain on, whether or not program material is playing.
If you will be away from home for an extended period of time, or if the subwoofer will not be used, switch the Master
Power Switch ⁄ to the OFF position.
Volume
Volume can be adjusted using the
Subwoofer-Level Control ‚, as shown below.
Subwoofer
Level
Subwoofer
Level
MIN MAX
MIN MAX
Additional Bass Adjustments
In addition to the volume adjustments described above, the SUB-TS10 subwoofer includes a Phase Switch ∞ and a Filter
Switch § that can be used to adjust the bass response to suit your listening environment or taste.
In most situations, the Phase Switch ∞ should be left in the NORMAL position. If you suspect that the subwoofer is playing out of phase with the other speakers, which would tend to diminish bass response, try placing this switch in the REVERSE position. There is no harm in experimenting, and you may return the switch to the
NORMAL position at any time. If you rearrange your room and reposition the speakers, it would be a good idea to check whether they are in phase by flipping this switch.
The High-Cut (Low-Pass) Filter Switch
§ limits the frequencies of the audio signal inputted to the subwoofer to the low frequencies that the subwoofer reproduces best. This allows the subwoofer to perform more efficiently, and with superior bass reproduction, minimizing distortion that might occur if the subwoofer attempted to reproduce higher frequencies. This switch should be left in the ON position, except:
1. When the SUB Input £ is being used, in which case it has no effect, or
2. When the Speaker-Level Inputs ™ or the Line-Level Full-Range Inputs ¢ are being used with a crossover or filter on board the receiver or processor. In these two circumstances, place the switch in the
OFF position.
8
HKTS 10 harman/kardon
9
If there is no sound from any of the speakers:
• Check that receiver/amplifier is on and a source is playing.
• Check that the powered subwoofer is plugged in and its Master Power Switch
⁄ is switched on to the “
• ” position.
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• Review proper operation of your receiver/amplifier.
If there is no sound from the center speaker:
• Check all wires and connections between receiver/amplifier and speaker. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• If your receiver/processor is set in
Dolby Pro Logic mode, make sure the center speaker is not in phantom mode.
• If your receiver/processor is set in
Dolby Digital or DTS mode, make sure the receiver/processor is configured so that the center speaker is enabled.
If there is no sound coming from one speaker:
• Check the “Balance” control on your receiver/amplifier.
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured, and that no wires are touching each other.
• In Dolby Digital or DTS mode, make sure that the receiver/processor is configured so that the speaker in question is enabled.
• Turn off all electronics and switch the speaker in question with one of the other speakers that is working correctly. Turn everything back on, and determine whether the problem is in the same place: i.e., the speaker that was working previously now has no sound and the speaker that was not working now sounds fine; or whether it has moved: i.e., the speaker that was not working still has no sound and the speaker that was working is still fine. If the problem is in the same place, the source of the problem is most likely with your receiver or amplifier, and you should consult the owner’s manual for that product for further information. If the problem has followed the speaker, consult your dealer for further assistance or, if that is not possible, visit our Web site at www.harmankardon.com for further information.
If the system plays at low volumes but shuts off as volume is increased:
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.
If there is low (or no) bass output:
• Make sure the SUB or line-level inputs of the SUB-TS10 subwoofer and SUB or LFE output of your receiver or amplifier are properly connected by the RCA-type patch cord.
• If you are using the SUB-TS10’s speakerlevel inputs, check your speaker cables to make sure they are all connected; that none of the wires are frayed, cut or punctured; and that you have maintained the correct polarity by connecting positive terminals to positive terminals, and negative terminals to negative terminals.
• Make sure the subwoofer is plugged into an active electrical outlet and its
Master Power Switch ⁄ is switched on to the “•” position.
• Check the speaker setup (bass management) settings in your AVR receiver or processor to make certain that the front, center and surround speakers are configured for “Small,” and that the subwoofer is set for “Yes” or “On.”
If there is no sound from the surround speakers:
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut or punctured.
• Review proper operation of your receiver/processor and its surround sound features.
• Make sure the movie or TV show you are watching is recorded in a surround sound mode. If it is not, check to see whether your receiver/processor has other surround modes you may use.
• In Dolby Digital or DTS mode, make sure your receiver/processor is configured so that the surround speakers are enabled.
• Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the desired Dolby
Digital or DTS mode, and that you have properly selected that mode using both the DVD player’s menu and the DVD disc’s menu.
HKTS 10
SIGNAL
GENERATOR
Test Set Up and Procedure
AC VOLT
METER (10V)
HKTS10
UNDER TEST
R L
LINE
LEVEL
IN
SUB
OFF
FILTER
ON
FILTER
REMOTE
CONTROL
L
PHASE
GREEN: ON
RED: STAND-BY
NORMAL REVERSE ON AUTO
IMPORTANT: CONNECT STRIPED WIRE TO RED ( ) SPEAKER TERMINAL.
R
SUBW OOFER LEVEL
AMPLIFIER
SUB-TS10 For use with
HKTS 10 System harman/kardon
Made in China
POWER
AC 120V~60Hz
{
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
General Unit Function (UUT = Unit Under Test)
1) From the signal generator, connect one line level (RCA) cable to the single Sub input on the UUT.
2) On the front of the unit, turn the LEVEL control full counterclockwise. FILTER control should be OFF.
3) Turn on generator, adjust to 75mV, 50 Hz.
4) Plug in UUT; turn the power switch ON. LED should be Red. Turn LEVEL control full clockwise (MAX)
5) LED should now be Green; immediate bass response should be heard and felt from port tube opening.
6) Turn off generator, turn VOLUME control fully counterclockwise, disconnect RCA cable.
7) Connect one pair of speaker cables to Speaker Level input terminal (IN) on Right channel only. Cables should be connected to an integrated amplifier fed by the signal generator.
8) Turn on generator and adjust so that speaker level input at the amplifier is 1.6V, 50 Hz. Turn LEVEL control full clockwise.
9) Green LED should light, immediate bass response should be heard and felt from the port tube opening.
Sweep Function
1) Follow steps 7-9 above, using a sweep generator as a signal source.
2) Sweep generator from 20Hz to 300Hz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or any other noises. If any unusual noises are heard, remove woofers and test.
Driver Function
1) Remove woofer from cabinet; detach + and - wire clips.
2) Check DC resistance of woofer; it should be 3.5 ohms ±10%
3) Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4) Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
10
HKTS 10 harman/kardon
11
HKTS 10 harman/kardon
HKTS 10 Subwoofer/Satellite/Center Mechanical/Packing Parts List
Part Number Description
Subwoofer SUB TS10
30PF14FM-DW02 xc125006-b xc125007 wi5334-1
06-T5305004
Satellites SAT-TS10
10PR70BZK-HW02
35DM13NG-PT02
XR5176-1 xc045016-b xc045017-1 xd045016-b
Center Channel CEN-TS10
10PR70BZK-MW02
35DM13NG-HT02 xr5177-1 xc045014-b xd045014-b xc045015-1
Packing/Accessories
wg5320 at5108 sal5009 sal063-1 sal5020 sal5044 wi5688 wi5689 wi5691
12" Woofer (DCR = 3.5 ohms +/-10%)
Front Baffle
Grille
Foot (4)
Screw for front baffle & Feet (8)
4" woofer
13 mm tweeter
Crossover Network
Baffle
Grille
Enclosure
Woofer 4"
13mm tweeter
Crossover Network
Baffle
Enclosure
Grille
Master carton
Warranty card
Wire set 40' (surround)
Wire set 20' (center)
Wire set 15' (front satellites)
15' RCA cable
Center Channel Bracket/Support
Foot
Wall Bracket for Satellite
12
HKTS 10
HKTS 10
harman/kardon harman/kardon
13
HKTS 10 harman/kardon
14
HKTS 10 harman/kardon
15
HKTS 10
Integrated Circuit Diagrams
harman/kardon
4558 DUAL OP AMP,
U203
OPAMP, QUAD 14P DIL TL074
U201, 202, 301
TIP31C NPN,
TIP32C PNP,
Q501, 502
TRANS, PNP, 2N5401 TAP,
TO-92,
Q503
TRANS, PNP, TAP,
2SA1015GR
Q101,107,112
B
C
E
TRANS, NPN, 2N5551 TAP,
Q114,115
TRANS, NPN, 2SC1815GR TAP,
2SC2235 Q108,109,111,113,
Q201-204,206-208,301,302
16
HKTS 10 harman/kardon
11016473j26
11016474j26
11016512j26
11016513j26
11016562j26
11016621j26
11016751j26
11016755j26
11016822j26
11016913j26
116161002f26
116161102f26
116162200f26
116162202f26
11012472j00
11020332jk3
11120102jk3
11130471jk2
11350s68j00
115h503a102
11016104j26
11016105j26
11016122j26
11016124j26
11016151j26
11016153j26
11016154j26
11016182j26
11016183j26
11016203j26
11016205j26
11016221j26
11016222j26
11016223j26
11016224j26
11016273j26
11016333j26
11016393j26
11016472j26
Capacitors
129a154j633
1302b101k503
1302b221k503
1302b470k503
SUBTS-10 Electrical Parts List
Input/Power Amp PCB
Part # Description
Resistors
11014103j26
11014222j26
11014432j26
11014472j26
11016102j26
11016103j26
Resistor 10K 1/4W ±5% CF
Resistor 2.2K 1/4W ±5% CF
Resistor 4.3K 1/4W ±5% CF
Resistor 4.7K 1/4W ±5% CF
Resistor 1K 1/6W ±5% CF
Resistor 10K 1/6W ±5% CF
Resistor 100K 1/6W ±5% CF
Resistor 1M 1/6W ±5% CF
Resistor 1.2K 1/6W ±5%CF
Resistor 120K 1/6W ±5% CF
Resistor 150 ohms 1/6W ±5% CF
Resistor 15K 1/6W ±5% CF
Resistor 150K 1/6W ±5% CF
Resistor 1.8K 1/6W ±5% CF
Resistor 18K 1/6W ±5% CF
Resistor 20K 1/6W ±5% CF
Resistor 2.0M 1/6W ±5% CF
Resistor 220 ohms 1/6W ±5% CF
Resistor 2.2K 1/6W ±5% CF
Resistor 22K 1/6W ±5% CF
Resistor 220K 1/6W ±5% CF
Resistor 27K 1/6W ±5% CF
Resistor 33K 1/6W ±5% CF
Resistor 39K 1/6W ±5% CF
Resistor 4.7K 1/6W ±5% CF
Resistor 47K 1/6W ±5% CF
Resistor 470K 1/6W ±5% CF
Resistor 5.1K 1/6W ±5% CF
Resistor 51K 1/6W ±5% CF
Resistor 5.6K 1/6W ±5% CF
Resistor 620 ohms 1/6W ±5% CF
Resistor 750 ohms 1/6W ±5% CF
Resistor 7.5M 1/6W ±5% CF
Resistor 8.2K 1/6W ±5% CF
Resistor 91K 1/6W ±5% CF
Resistor 10K 1/6W ±1% MF
Resistor 11.0K 1/6W ±1% MF
Resistor 220 ohms 1/6W ±1% MF
Resistor 22.0K 1/6W ±1% MF
Resistor 4.7K 1/2W ±5%
Resistor 3.3K 2W ±5%
Metal Film Resistor 1K 2W ±5%
Metal Film Resistor 470 ohms 3W ±5%
Cement Resistor 0.068 ohms 5W
Variable Resistor 50K
QTY Reference Designator
3 R503,504,510
1 R511
1 R506
1 R505
5 R153,213,214,215,254
36 R128,130,149,150,209,212,216,217,218,220,221,
222,225~229,230,232,234,235,240,248,260,
273~277,279,305,306,308,311,314,319
6 R122,126,231,263,266,307
1 R259
1 R265
1 R233
1 R253
1 R107
1 R252
2 R145,271
1 R262
1 R309
1 R257
1 R144
1 R102
5 R238,247,255,256,316
2 R272,278
2 R223,237
1 R310
1 R151
3 R200,207,258
7 R106,129,219,249,250,251,264
2 R127,312
2 R210,211
1 R224
1 R152
1 R160
1 R315
1 R313
1 R270
4 R203-206
2 R301,303
1 R302
1 R317
1 R318
2 R201,202
1 R134
1 R148
2 R501,502
1 R147
1 VR201 Level Pot
Metallize Cap. 0.15U 63V ±5% MSC
Metallize Cap. 100P 50V ±10%
Disc Capacitor 220P 50V ±10%
Disc Capacitor 47P 50V ±10%
2 C221,222
3 C302,303,306
12 C200,204,205,207,208,210,211,212,214,220,230,
237
1 C229
17
HKTS 10 harman/kardon
Part #
1302f104z503
132103j503
132103ja03
132104ja03
132183j503
132223ja03
132273ja03
132473ja03
1353105m50
1353106m50
1353107m10
1353107m16
1353107m35
1353225m50
1353216
1353250
1353227m16
1353476m16
132103kb00
1385478m63
1385478m63
Semiconductors
192027c1815gr
192027c2235y
192028a1015gr
1921672n5551
1921682n5401
197131n4148
19915000335
19915000625
19915001605
192161tip31c
192162tip32c
19510204hgw
19700kbu606g
197101n4004
19006m4558d
19016tl074cn
Miscellaneous
1091ttc802j0
1201000003
171urwh124d
1740rca326p
1741jy35421
17420810360g
180tms7210v
150r4055900a
152u602015
154k31505t0
15563032i
180pbr12c11s
Description
Disc Capacitor 0.1U 50V +80/-20%
Mylar Capacitor 0.01U 50V ±5%
Mylar Capacitor 0.01U 100V ±5%
Mylar Capacitor 0.1UF 100V ±5%
Mylar Capacitor 0.018U 50V ±5%
Mylar Capacitor 0.022uF 100V ±5%
Mylar Capacitor 0.027U 100V ±5%
Mylar Capacitor 0.047uF 100V ±5%
Electrolytic Cap. 1U 50V ±20%
Electrolytic Cap. 10U 50V ±20%
Electrolytic Cap. 100U 10V ±20%
Electrolytic Cap. 100uF 16V ±20%
Electrolytic Cap. 100U 35V ±20%
Electrolytic Cap. 2.2U 50V ±20%
Electrolytic Cap. 22U 16V ±20%
Electrolytic Cap. 22U 50V ±20%
Electrolytic Cap. 220U 16V ±20%
Electrolytic Cap. 47U 16V ±20%
Mylar Cap. 0.01U 200V ±10%
Electrolytic Cap.4700U 63V ±20%
Electrolytic Cap.4700U 63V ±20%
Transistor 2SC1815GR
Transistor 2SC2235Y
Transistor 2SA1015GR
Transistor 2N5551
Transistor 2N5401
1N4148
Zener Diode 3.3V 1/2W 52mm
Zener Diode 6.2V 1/2W 52mm
Zener Diode 16V 1/2W 52mm
Transistor TIP31C SGS
Transistor TIP32C SGS
LED 204HGW Indicator
Diode 6A 800V KBU606G
1N4004
I.C. OPA 4558D Dual Op-amp
I.C. TL074CN ST Quad Op-amp
Thermister TTC-802(JS) NTC
Inductor 10W
Relay RWH-SH-124D (1600 ohm)
JACK RCA-326 PURPLE/WHT/RED
PHONE JACK 3.5mm JY-3542-01-030
SPK JK.BP 8PIN SH0810360G
SWITCH SLIDE 6PIN MS7210V
Power Transformer I/P:120V/60Hz
Line Cord SVT FT-2 6FT
Fuse 3.15A 250V 30mm UL/CSA
Fuse Holder HTB-32I 30mm UL/CSA
PUSH SW BR12C11S
QTY Reference Designator
14 C107,117,122,144,232,242,244,245,246,252,254,
256,320,322
2 C305,317
2 C103,104
4 C123,218,503,504
2 C223,224
1 C215
1 C143
2 C216,217
1 C228
12 C201,202,206,213,219,231,241,243,251,253,319,
321
2 C114,115
1 C234
2 C507,508
1 C509
1 C304
3 C225,505,506
2 C118,233
1 C318
1 C500
1 C501
1 C502
12 Q108,109,113,201-204,206,207,208,301,302
1 Q111
3 Q101,107,112
2 Q114,115
1 Q503
18 D102,103,104,105,143,201,202~208,214,215,
216,310,312
1 D213
1 D101
1 D502
1 Q501
1 Q502
1 D209
1 D501
2 D110,504
1 U203
3 U201,202,301
1 TH1
2 FB1,2
1 RL1
1 JK201 (Set of three)
1 JK203
1 JK202 (Set of eight)
3 Filter/Phase/Auto-on-off
1 T501
1
1 F501
1 F501
1 SW501 POWER
18
HKTS 10
Power Amp Module PW150D
Ref. Designator Part#
Resistors
11812061001j
11812061002j
118120610r0j
11812061201j
11812062002j
11812062201j
11812062701j
11812063000j
11812063301j
11812063902j
11812064700j
11812064701j
11812064702j
11812064704j
118120647r0j
Capacitors
141c0101k50
141c0220k50
141c0561k50
141c6104m50
141c7223k50
141d7104ka0
128e106ma01
141d7104kb0
Semiconductors
19016tl072dts
19209124126qs
19209139066rs
19209210376qs
19209215146rs
19703rls4148s
19915000563s
19915001203s
19915001503s
192232irf9640
192233irf640
Miscellaneous
1759f40hr2
12214121m4191
12214350j4180
06-t3085020
06-t31207
R2,11,29,30
R7,9,25
R22,23
R31-46
R26
R6,13,16
R10
R24
R14,15,27,28
R3
R8
R1,5,12
R17
R4
R20,21
C4
C5
C6
C2,3,7,8,9,10,11,15
C13
C1
C16,17
IC1
Q1,4,5
Q2,8
Q7,9
Q3,6
D1,2,3,4,5,6
Z1,2
Z5,6
Z3,4
Q10
Q11
Description
RES, 1.00K 1206 5%
RES, 10.0K 1206 5%
RES, 10.0 ohms 1206 5%
RES, 1.20K 1206 5%
RES, 20.0K 1206 5%
RES, 2.20K 1206 5%
RES, 2.70K 1206 5%
RES, 300.0 ohms 1206 5%
RES, 3.30K 1206 5%
RES, 39.0K 1206 5%
RES, 470 ohms 1206 5%
RES, 4.70K 1206 5%
RES, 47.0K 1206 5%
RES, 4.70M 1206 5%
RES, 47.0 ohms 1206 5%
CAP,CA 100pF 50V 10% 1206 NP0
CAP,CA 22pF 50V 10% 1206 SMT NPO
CAP,CA 560pF 50V 10% 1206 NPO
CAP,CA 0.1uF 50V 20% 1206 Z5U
CAP,CA 0.022uF 50V 10% 1206 X7R
CAP,NP 0.1uF 100V 10% 1210 X7
CAP,E NP 10uF 100V 20%
CAP,NP 0.1uF 200V 10% 1210 X7
SMD I.C. TL072CDT SGS Dual Op-Amp
TRANS, NPN 50V 0.15A 2SC2412K
TRANS, NPN 120V 0.05A 2SC3906K
TRANS, PNP 50V 0.15A 2SA1037K
TRANS, PNP 120V 0.05A 2SA1514K
Diode RLS4148
ZENER 5.6V 5% PHILIPS BZX84-C5 V6
ZENER 12V 5% PHILIPS BZX84-C12
ZENER 15V 5% PHILIPS BZX84-C15
FET IRF9640 IR P-CH TO220
FET IRF640 IR N-CH TO-220
harman/kardon
Wafer 40PIN PITCH=2.54mm HR2*40
L1 Ferrite core LS-A6206-ST EFD-30 1
L2 Inductor 35uH 1
PCB TO H/S-2,PCB TO PCB/H-4 SCREW 3*8 6
TO HSQLC1004/ID150-1 SCREW M3*12 1
Qty
2
1
1
1
1
8
1
1
1
1
2
1
3
4
1
1
1
1
3
4
3
2
16
2
2
2
6
2
2
1
3
2
1
1
19
HKTS 10 harman/kardon
20
HKTS 10 harman/kardon
21
HKTS 10 harman/kardon
22
advertisement
Key Features
- 150 watt powered amplifier
- Subwoofer with 12-inch woofer and bass-reflex enclosure
- Satellites and center channel with 1-inch dome tweeters and 4-inch midrange drivers
- Remote control
- Subwoofer level control
- Phase switch
Related manuals
Frequently Answers and Questions
What is the recommended power range for the satellites and center channel?
What is the impedance of the satellites and center channel?
What is the frequency response of the system?
What is the sensitivity of the satellites and center channel?
What are the dimensions of the subwoofer?
What is the weight of the subwoofer?
advertisement