Cino FuzzyScan F680BT Reference Manual

WIRELESS IMAGER
Reference Manual
International Edition, Rev. C7
Revision History
Rev. No.
Released Date
Rev. A
Oct 16, 2009
Rev. A1
Oct 22, 2009
Rev. A2
Rev. A3
Description
First Release
Page 6
Page 68
Revise “Clone Function” operation method.
Add “Save Configuration” and “Master Default” to System Commands.
Page 53
Page 69
“Bluetooth Device Name” – Modify user define characters from 1 – 14 characters to
1 – 16 characters.
Add “Indications”.
Page 25
Page 43
Page 45
Page 48
Modify UPC-E/EAN-8 expansion and UPC-A standardization.
Rename “Time Out Control” to “Serial Response Time-out”.
Rename “Presentation Scanning Mode” to “Presentation Control”.
Rename “Auto Power Off Duration” to “Light Source On Time”.
Page 49
Add “Extremely short” option to Good Read Duration.
Rename “Presentation Scanning Auto-sense” to “Presentation Auto-sense”.
Nov 27, 2009
Mar 05, 2010
Add “Presentation Sensitivity”
Wireless FuzzyScan
Reference Manual
Rev. A4
Rev. A5
Rev. A6
Apr 27, 2010
Page 38
Page 43
Hands Free Time-out – Add “Disable”.
Baud Rate – Add 57.6K BPS and 115.2K BPS.
Jun 28, 2010
Page 27
Page 49
Page 47
Page 48
Add “UPC/EAN Security Level”.
Add “Time Delay to Low Power Trigger”
Add “Good Read Indicator”.
Add “Scan Voting”.
Page 25,26
Rename ”Scan Voting” to “Supplement Scan Voting” and add “Supplement Scan
Voting” in Symbology Reading Control
Add “EAN Supplement Control”
Sep 20, 2010
Page 27
Page 38
Keyboard Layout – Add “Czech (QWERTY)”, remove “Universal”, and rename
Spain (QWERTY) to Spain (Spanish QWERTY), Latin America (QWERTY) to Spain
(Latin America, QWERTY)
Revision History
Rev. No.
Released Date
Page 48
Remove ”Scan Voting” and add “Scan Rate Control ”
Rev. A6
Sep 20, 2010
Page 54
Add “<Scanned Data><Field Delimiter><Quantity>” parameter selection in Batch Data
Quantity Output Format.
Rev. A7
Nov 10, 2010
Page 44
Baud Rate – Cancel Baud Rate 300/600 BPS.
Page 47
Rev. A8
Jan 2, 2011
Buzzer Tone Adjust – Modify No power-on beep behavior. The setting of No
power-on beep will impact both Bluetooth Scanner and Smart Cradle.
Add “Beeping Control” setting.
Rev. A9
Mar 04, 2011
Page 44
Baud Rate – Revise 57.6K BPS and 115.2K BPS option code from 6.7. to 8.9.
Page 23
Add ”Code 39 Security Level”.
Page 45
Add “NAK Retry Count”.
Add “ACK/NAK Transmission Indication”.
Add “Numeric Bar Codes ”.
Add “Connecting Apple iOS Devices Quick Sets”.
Rev. B1
Description
Mar 22, 2011
Page 69
Page 73
Wireless FuzzyScan
Reference Manual
Page 19, 29, 34, 67
UCC/EAN-128 was renamed GS1-128.
Page 45
Rename “ACK/NAK Transmission Indication” to “ACK Indication”.
Page 45
Rename the 2 parameters of the “ACK Indication”.
(Disable→ Disable ACK Time-out Indication, Enable→ Enable ACK Time-out
Indication)
Rev. B2
Jul 22, 2011
Page 45
Add 2 new parameters to “ACK Indication”.(Disable ACK Indication, Enable ACK
Indication)
Page 47
Add 6 parameters to “Serial response time -out”. (800 m seconds, 3 seconds, 4
seconds, 8 seconds, 10 seconds, 15 seconds)
Page 47
Cancel the parameter "User defined value (seconds)” of “Serial response time
-out”.
Add “Laser Aiming Control” function.
Page 54
Revision History
Rev. No.
Released Date
Rev. B3
Nov 04, 2011
Rev. B4
Jan 03, 2012
Description
Page 3, 5, 10 “Paging/ Reset button” is changed from 3 seconds to 5 seconds.
Page 24
Add a new function “Codabar Check Digit Settings”
Page 49
Cancel 1 parameter of “Code 39/Code 128 Emulation”.(Disable standard cod 39
emulation - -0)
Page 49
Change of default setting to Enable standard code 39 skip emulation in “Code 39/
Code 128 Emulation”.
(Disable standard code 39 emulation (0)→ Enable standard code 39 skip
emulation (1))
Rev. B5
Wireless FuzzyScan
Reference Manual
Rev. B6
Rev. B7
Mar 05, 2012
Jul 25, 2012
Aug 20, 2013
Jan 15, 2014
Rev. C1
Jan 23, 2014
Page 56
Add 3 new functions:”1D Barcode Forward-reading Indication”, “1D Barcode
Backward-reading Indication”, “1D Barcode Direction Indication Transmission”
Page 18
Add ”USB HID Legacy” option for “Host Interface Selection”.
Page 23
Add “Code 128 security level”
Page 49
Restore the behavior and default setting of the Code39/Code 128 Emulation in
“Wand/Laser Emulation Control” function.
Page 56
Add “LED illumination Control” and “LED Illumination Delay” functions for Trigger
Mode and Low Power Mode.
Page 21
Modify “Readable Bar Code Setting” section
Page 69
Modify “Symbology ID Table”
Support 2D Functions
Page 2
Change the indicator of full charged status to “steady green”
Page 7
Add “HID Legacy Mode” and HID Mode with Passkey”
Page 10
Add “Sleep Mode” and “Power Off”
Page 11
Modified “Quantity Feature” of Batch Scanning
Page 69
Modified “Presentation Sensitivity”
Revision History
Rev. No.
Released Date
Description
Support 1D Pocket Scanner
Rev. C2
Reference Manual
Page 21:
Add “USB EFT Terminal Mode” for “Host Interface Selection”.
Page 96
add “USB HID Legacy Mode” Host Interface Quick Set Command.
Page 97
Add “Abort” Quick Set Command
Rev. C3
May 09, 2014
Page 16
Add “Clear All Scanned Data” Command.
Rev. C4
Feb. 06, 2015
Page 50
Add “MaxiCode Setting”
Page 13
Add “Paging Function”
Page 71
Add “Radio Connection Beeps”
Page 73
Add “HID Mode Transmit Delay”
Page 85
Remove “HID Link Quality Setting” and add “Link Quality Control”
Page 74
Modified “Good Read Duration”
Page 98
Modified “Uninstall” Quick Set
Rev. C5
Wireless FuzzyScan
May 08, 2014
Rev. C6
Mar. 09, 2015
June. 03, 2015
Support 2D Pocket Scanner
Page 3
Add “Using the Function Keys of Pocket Scanner”
Page 13
Add “ Enter Bluetooth Discoverable Mode”
Remove “Sleep Mode” and modify “Power Off”
Rev. C7
Sep. 09, 2015
Page 15
Modify “How to Transmit Stored Data”
Page 16
Add “How to Delete Last Scanned Data”
Page 17
Add “Simultaneous Barcode Scanning and On-screen Keyboard”
Page 18
Add “ Check Battery Status” & Battery Status Indication
Page 74
Add “Buzzer Volume”
Page 75
Add “Timestamp Functions”; including Set Date, time, and Timestamp Format setting
Page 76
Add 2D “Stored Data Output Format”
Revision History
Rev. No.
Released Date
Description
Page 77
Add “Radio Link Mode for Discoverable Mode”
Page 79
Modify “HID Mode Transmit Delay”
Page 80
Rename “Time Delay Low Power Trigger” to “Time Delay to Low Power Standby
Mode” and change default value to 5secs
Add “Low Power Stand-by mode Link Indication”
Change “Good Read Duration default value to “1””
Rev. C7
Page 86
Remove “Link Supervision Time Out”
Page 87
Rename “Sleep Time-out Control” to “Radio-off Time-out Control”;
Change default value of connect state to 12(x5) min.; and change default value of
disconnect state to 5 (x1) min,
Sep. 09, 2015
Change “power Off Time –out” default value to 1(x5) min
Wireless FuzzyScan
Reference Manual
Set “power off Time out” to “0” will enter power-off mode immediately
Page 89
Change “Batch Data Quantity Output Format” to “Stored Data Output Format”
Page 91
Rename “Bluetooth Power Saving Mode” to “Bluetooth Sniff Control”; Enable
Bluetooth Sniff Control.
Modify “Link Quality Control”
Page 92
Add “On-screen Keyboard Control”
Page 108
Add “General Approach”, “iOS Approach” and “Switch On-screen Keyboard” Quick
Sets.
Page 110
Remove “Sleep” system command
© Copyright PC Worth Int’l Co., Ltd
Cino makes no warranty of any kind with regard to this publication, including, but not limited to, the implied warranty of
merchantability and fitness for any particular purpose. Cino shall not be liable for errors contained herein or for incidental
consequential damages in connection with the furnishing, performance, or use of this publication. This publication contains
proprietary information that is protected by copyright. All rights are reserved. No part of this publication may be photocopied,
reproduced or translated into any language, in any forms, in an electronic retrieval system or otherwise, without prior written
permission of Cino. All product information and specifications shown in this document may be changed without prior notice.
Warranty
Wireless FuzzyScan
Reference Manual
Cino warrants its products against defects in workmanship and materials from the date of shipment, provided that the
product is operated under normal and proper conditions. The warranty provisions and durations are furnished by different
warranty programs. The above warranty does not apply to any product which has been (i) misused; (ii) damaged by accident
or negligence; (iii) modified or altered by the purchaser or other party; (iv) repaired or tampered by unauthorized
representatives; (v) operated or stored beyond the specified operational and environmental parameters; (vi) applied
software, accessories or parts are not supplied by Cino; (vii) damaged by circumstances out of Cino’s control, such as, but
not limited to, lightning or fluctuation in electrical power. Any defective product must follow the warranty program and RMA
procedures to return Cino for inspection.
Regulatory
FCC part 15B, FCC part 15C
EN61000-6-2, EN61000-6-3, EN60950-1, EN301 489-1, EN301 489-17, EN300 328
EN55022, EN55024
CNS13438, CNS14336
AS/NZS CISPR 22:2009/Amdt 1:2010 Class B
Clause 2, Article 58-2 of Radio Waves Act
V.3/2011.04, Technical Requirements, Class B ITE
LP0002
MIC T401
LED Eye Safety
IEC62471 Exempt group
Wireless FuzzyScan
Reference Manual
Laser Eye Safety IEC60825-1 Class 1
Table of Contents
Getting Started
Getting Familiar with Your FuzzyScan
Preparation before Using
Decide Your Radio Link Mode
Use FuzzyScan in PAIR Mode
Use FuzzyScan in PICO Mode
Use FuzzyScan in HID Mode
Use FuzzyScan in SPP Mode
Out-of-range Scanning/Presentation Scanning/ Power Off
Batch Scanning (Inventory Mode)
1
3
5
6
7
9
10
12
14
Wireless FuzzyScan
Reference Manual
Configure Your FuzzyScan
Bar Code Programming Manual
Programming Procedures
Host Interface Selection
Symbology Reading Control
Keyboard Interface Control
Serial Interface Control
Wand/Laser Emulation Control
Operation Control
Condensed DataWizard
19
20
24
25
56
61
65
67
97
Appendix
Symbology ID Table
Keyboard Function Code Table
ASCII Input Shortcut
Link Mode Quick Set/Operation Mode Quick Set
Host Interface Quick Set
Option Codes
System Commands
Indications
101
103
104
105
106
107
109
110
Getting Started
Getting Familiar with Your FuzzyScan
Thank you for choosing Cino FuzzyScan Bluetooth Cordless Image Scanner. Powered by the combination of cutting-edge
FuzzyScan Imaging Technology and Bluetooth wireless technology, it not only provides outstanding reading performance,
but also delivers the convenience and freedom of mobility. It’s ideal for a broad range of applications to unleash your
productivity with ease. This document provides a quick reference for installation and operation. The complete documentation
is available at www.cino.com.tw.
A770BT Series
HB211x Smart Cradle
Central Indicator
Side Indicators
Paging/Reset Button
USB Bus Power Switch
Host Interface Port
DC Power Jack
F780BT & L780BT
Link Indicator
HB2100 USB Charging Cradle
Wireless FuzzyScan
Reference Manual
Status Indicator
Beeper
Central Power Indicator
Scan Window
Trigger
Reserved
USB Bus Power Switch
Battery Cavity
End Cap
USB Port
DC Power Jack
F680BT & L680BT
1
Getting Started
PA670BT & Px680BT Scanners
Status Indicator
Power/Link Indicators
Left Key
Function Key 1 (FN1)
Function Key 2 (FN2)
Right Key
Trigger
Battery Cover
Reset Key
Micro USB Port
Wireless FuzzyScan
Reference Manual
Scan Window
Central Indicator
Side Indicators (HB3112 only)
USB Bus Power Switch
Mounting Holes
DC Power Jack
Paging/Reset Key
Host Interface Port (HB3112)
USB Port (HB3100)
2
Getting Started
Using the Function Keys of Pocket Scanner:
Function Keys
Functions
Actions
Check battery status
Short press the key
Transmit stored batch data
Long press the key
Power off the scanner
Long press the key
On-screen keyboard toggle
Short press the key
Enter Bluetooth discoverable mode
Long press the key
Delete last scanned data (batch scanning)
Short press the key
Enter batch scanning (inventory mode)
Long press the key
Left Key
Right Key
Function Key 1
Function Key 2
Wireless FuzzyScan
Reference Manual
Short Press: Press the key for less than 1 second.
Long Press: Press and hold the key for more than 3 seconds.
3
Getting Started
Preparation before Using – Gun type Scanners
Install the Battery
Ensure the battery contacts of the battery pack are facing the charging contacts inside
the battery cavity.
Slide the battery pack into the battery cavity until hearing a click sound before locking it
with the end cap. The scanner will give 4 beeps when the battery pack is installed
properly if the battery pack still has power.
Secure the end cap with the screw provided.
Charging the Battery
Choose an appropriate plug and slot it into the power adapter cavity until it is locked.
Then plug the AC power plug into the AC wall socket.
Wireless FuzzyScan
Reference Manual
Plug the DC power cord of power supply unit into the DC Jack of the cradle. The smart
cradle emits the power-on beeps and the central indicator gives one blue blink. If you
use the charging cradle, the central power indicator turns steady blue.
Place the scanner on the cradle. The status indicator of scanner turns steady red if the
battery is not fully charged. When the battery is fully charged, the status indicator of
scanner turns steady green.
Please charge the new battery pack for 8 hours before its first use.
Use USB Bus Power
If USB 3.0 is available in your host device, both battery charging and regular operation
can be supported by the USB Bus Power without using external power supply.
If only USB 2.0 is available in your host device, we recommend using external power
supply as power source, because the power supplied from USB2.0 is not enough to
support both battery charging and regular operation simultaneously.
If you want to use this feature, please slide the USB bus power switch to “ON”. Then
connect the cradle to the host device via USB cable.
4
Getting Started
Preparation before Using – Pocket Scanners
Install the Battery
Take off the battery cover from the scanner by removing two blue tapes.
Ensure the battery contacts of the battery pack are facing the charging contacts inside
the battery cavity. Then click the battery pack into the battery cavity carefully.
Place the battery cover in the right orientation onto the back of the scanner. Screw in
and tighten the four shipped M2 screws in sequence by a small screw-driver in the
clockwise direction.
Charging the Battery via Power Supply Unit
Choose the right plug and slot it into the power supply unit cavity until a “click” is heard.
Then plug the power supply unit into the wall outlet
Please make sure the USB bus power switch is in “OFF” position.
Wireless FuzzyScan
Reference Manual
Plug the DC connector of the power supply unit into the DC Jack of the cradle. The
cradle emits four beeps. For the Smart cradle, the central indicator blinks blue once
and side indicators lights red. For the charging cradle, the central indicator lights blue.
Place the scanner onto the cradle. When the battery is fully charged, the status
indicator of scanner will light green.
Charge the Battery via USB 3.0 Port
The scanner can also be charged via the USB 3.0 port without the power supply unit.
You can connect the cradle to USB 3.0 port of host device by a USB cable, then slide
the USB bus power switch to “ON”. After that, place the scanner onto the cradle.
The scanner can also be charged via its micro USB port by connecting the micro USB
cable to USB 3.0 port of host device or the commercial USB power adapter connected
to the wall socket.
5
Getting Started
Decide Your Radio Link Mode
The FuzzyScan Bluetooth image scanner provides several radio link modes to communicate with most host devices. When
the Bluetooth-enabled host device is not available, it can work with the smart cradle in PAIR mode (peer-to-peer connection)
or PICO mode (multiple connections) to provide a plug-and-play cordless migration of your existing non-Bluetooth-enabled
devices. Moreover, you are also able to use the scanner to work with Bluetooth-enabled host devices via SPP mode or HID
mode.
When the radio link is disconnected, the scanner is capable of reconnecting the radio link automatically when it returns to the
communication coverage. But please note that this feature is not available in SPP slave mode. If you would like to change
the radio link mode, please scan the “Uninstall” command to reset the scanner to uninstall state.
PAIR Mode
If the Bluetooth device is not available in your existing system, PAIR mode is the simplest plug-and-play solution. In this
mode, a smart cradle can only work with one scanner. The smart cradle not only provides the Bluetooth radio link with the
scanner, but also offers the legacy cabled interfaces to the host device, including USB HID, USB COM, PS/2(DOS/V)
Keyboard Wedge and RS232 Serial.
Wireless FuzzyScan
Reference Manual
PICO Mode
For the requirement of multiple connections, up to 7 scanners can be connected to one smart cradle concurrently. If you
would like to un-pair all scanners paired with the smart cradle, please press and hold the paging/reset button of the smart
cradle for more than 5 seconds. If you just want to un-pair part of the paired scanners, please take those paired scanners to
scan the “Uninstall” command one by one.
HID Mode
Through the most useful HID service, the scanner can work as a Bluetooth Keyboard. In this mode, the scanner will be
discoverable by the radio connection request issued by the remote host device. For some cases, you may be requested to
enter the Passkey (PIN) to establish the Bluetooth connection for security purpose.
SPP Master/Slave Mode
Through the standard SPP service, the scanner can work as a Bluetooth Serial Device. In SPP master mode, the scanner
initiates the radio connection request to the remote slave device. In SPP slave mode, the scanner will be discoverable by the
radio connection request issued by the remote host device.
6
Getting Started
Use FuzzyScan in PAIR Mode
Ensure the battery is fully charged. You may refer to the section of Preparations before Using for details.
Please choose your desired interface cable, then plug it into the host interface port of the smart cradle and connect it to
the host device.
USB
PS/2
RS232
Turn on the power of your host device.
Power on or wake up the scanner by pressing the Trigger key if the scanner is power-off.
This scanner is pre-paired with the shipped smart cradle, so you will see the link indicators of scanner blink blue per 2.5
seconds, and the central indicator of the smart cradle light blue. If the scanner and smart cradle are not paired, the
status indicator of scanner and the side indicators of smart cradle blink red and green alternatively (in “Uninstall” state).
Please follow step 6 to establish the connection.
Wireless FuzzyScan
Reference Manual
Scan “PAIR mode” command. The status indicator of scanner will turn steady red immediately.
Uninstall
PAIR Mode
Place the scanner on the smart cradle, then you will hear one short beep to indicate the pairing process is activated. The
scanner will emit continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing process.
When you hear 4 beeps in ascending tone, the pairing process is completed. You will see that the link indicator of scanner
gives 1 blue blink per 2.5 seconds and the central indicator of the smart cradle lights blue.
If the scanner pairing process failed or it’s not placed on the smart cradle within 20 seconds, you will hear 2 “Di-do Di-do”
beeps to warn the failure of pairing, the scanner will return to uninstall state automatically.
Scan the corresponding host interface quick set command to complete the installation.
The default host interface of smart cradle is preset to USB HID. If you want to set the host interface to USB COM, you
have to install the USB virtual COM driver into your host device before using the scanner. Please visit CINO website to
download the driver.
7
Getting Started
Use FuzzyScan in PICO Mode
Ensure the battery is fully charged and choose your desired interface cable, then plug it into the host interface port of the
smart cradle and connect it to the host device.
USB
PS/2
RS232
Turn on the power of your host device.
Ensure the side indicators of the smart cradle blink red and green alternatively (in “Uninstall” state). If the smart cradle
is paired with other scanners, please press and hold the paging/reset button for more than 5 seconds to un-pair all
paired scanners. Then the smart cradle will return to uninstall state automatically.
Wireless FuzzyScan
Reference Manual
Prepare the scanners you desire to pair with smart cradle. Power or wake up the scanner by pressing the Trigger key if
the scanner is power-off. Ensure the status indicator of each scanner blinks red and green alternatively (in “Uninstall”
state). If the scanner is not in uninstall state, please scan the “Uninstall” command to un-pair the scanner, then scan the
“PICO mode” command, and the status indicator of scanner will light red.
Uninstall
PICO Mode
Place the scanner onto the smart cradle, then you will hear one short beep to indicate the pairing process is activated.
The scanner will emit continuous short clicks and the link indicator of scanner will flash blue quickly during the pairing
process. When you hear 4 beeps in ascending tone, the pairing process is completed. You will see that the link indicator
of scanner blinks blue once per 2.5 seconds; the central indicator of the smart cradle lights blue and its side indicators
light green.
If the scanner pairing process failed or it’s not placed on the smart cradle within 20 seconds, you will hear 2 “Di-do Di-do”
beeps to warn the failure of pairing, the scanner will return to uninstall state automatically.
Please scan the corresponding host interface quick set command to complete the installation. Then repeat the same
procedure to pair other scanners with the smart cradle.
For user’s convenience, the smart cradle will automatically assign the ID numbers to each scanner. Please scan the
System Information command to check the assigned ID number of each scanner.
8
Getting Started
Clone Function
For the user’s convenience, the clone function will help you to clone the host interface related parameters (please refer to
following table for details) from one of the paired scanners to the rest of paired scanners under PICO mode. You can use
one of the paired scanners to set the host interface related parameters first and then scan “Save Configuration” command.
After that, please take the other paired scanners to scan “Clone” command one by one to clone the host interface related
parameters.
Please ensure to keep those paired scanners in connected status when you use the Clone function. Because the host
interface related parameters can’t be cloned to the paired scanner in disconnected status.
Save Configuration
Clone
The below host interface related parameters will be impacted by clone function:
Data Transmission Parameter
Serial Interface Control
Field Delimiter
Handshaking Protocol
Data Transmission Format
Intermessage Delay
Wireless FuzzyScan
Reference Manual
Host Interface Control
Interfunction Delay
Host interface Selection
Intercharacter Delay
Keyboard Interface Control
Baud Rate
Keyboard Layout
Data Frame
Intermessage Delay
Time Out Control
Interfunction Delay
Wand Emulation Control
Intercharacter Delay
Output Polarity
Caps Lock Control
Initial Signal State
Caps Lock Release Control
Margin Time
Function Key Emulation
Module Time
Key Pad Emulation
Narrow/Wide Ratio
Upper/Lower Case
Code39 Emulation
9
Getting Started
Use FuzzyScan in HID Mode
Ensure the battery is fully charged. Power on the scanner by pressing the Trigger key within radio range if the scanner is
power-off, and ensure the status indicator of scanner gives alternative red and green blinks (in “Uninstall” state). If the
scanner is not in uninstall state, please scan the “Uninstall” command first.
Uninstall
If your remote host is equipped with latest Bluetooth drivers, or it’s an iOS or Android device, you are recommended to
use “HID Mode” for quick pairing. If necessary, you may use “HID Mode with Passkey” to establish a more secure
connection, If you frequently experienced the problem in using HID mode, please try “ HID Legacy Mode” instead.
HID Mode
HID Legacy Mode
HID Mode with Passkey
Once you scan one of above commands, the link indicator of scanner will blink blue 3 times per 2 seconds during
searching process. You have to execute the Bluetooth Discovery procedure to find available Bluetooth device, then select
“F(L/A)xxxBT-xxxx” or “PF(L/A)xxxBT-xxx”.
Wireless FuzzyScan
Reference Manual
If you use “HID Mode”, please go to step 5.
If you use “HID Mode with Passkey”, you will be requested to enter the Passkey (PIN) on the remote host. Please enter
the Passkey (PIN) accordingly by scanning the “Option Code” (Page 97), and then scan the “FIN (Finish)” to end the
Passkey entry, then go to step 5.
If you scan “HID Legacy Mode”, the Passkey (PIN) may be requested. Please enter “00000000” (default setting). You will
see “Keyboard on F(L/A)xxxBT-xxxx” or “Keyboard on PF(L/A)xxxBT-xxxx”. Please double click this HID service to
establish the connection between scanner and remote host device.
The scanner will emit 4 beeps in ascending tone to indicate the connection is established. At the same time, the link
indicator of scanner will blink blue once per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within 1 minute after scanning the above command,
the scanner will go off automatically. You can just press the trigger to wake up the scanner to continue the installation.
The installation procedure may vary depending on different remote host devices, operating systems and the Bluetooth
drivers. Please consult your professional IT consultant to obtain necessary support. For more detailed information,
please visit CINO website.
10
Getting Started
Use FuzzyScan in SPP Mode
Establish SPP Master Connection
Ensure the battery is fully charged. Please go to the folder “Hardware” located in Bluetooth Advanced Setting of the
remote host device to check its device MAC address. Then prepare a 12-character Code 128 barcode of the remote host
device MAC address, or follow the step 4 to input MAC address by scanning 12 option codes.
Ensure a virtual COM port is available in your remote host for connecting the scanner. If not, please go to the folder
“Local Services” located in Bluetooth Advanced Setting. Click the “Add Serial Services” to add one more Bluetooth
COM port.
Power on or wake up the scanner by pressing the Trigger key within radio coverage if the scanner is power-off, and
ensure the status indicator of scanner blinks red and green blinks alternatively (in “Uninstall” state). If the scanner is
not in uninstall state, please scan the “Uninstall” command first, then scan the “SPP Master Mode” command. The status
indicator of scanner will turn steady red immediately.
Uninstall
SPP Master Mode
Wireless FuzzyScan
Reference Manual
Scan a 12-character MAC address barcode, or scan 12 option codes and “FIN” command to confirm your inputs. The
scanner will emit continuous short clicks and the link indicator of the scanner will blink blue quickly during the radio
connecting process. If the PIN Code or Passkey is requested, please enter “00000000” (default setting).
The scanner will emit 4 beeps in ascending tone to indicate the radio is connected. At the same time, the link indicator of
scanner will blink blue once per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner failed to connect to the host device within 30 seconds, the link indicator will blink blue 3
times per 2 seconds. But the scanner is still continuing to discover the host device for another 30 seconds before go off.
In the interim, you still can scan “Uninstall” command to revert the scanner to uninstall state. If the scanner goes off
already, you just need to press the trigger to wake up the scanner to continue the installation.
The above procedures are based on popular Windows environment. But the installation procedure may vary
depending on different remote host devices, operating systems and the Bluetooth drivers. Please consult your
professional IT consultant to obtain necessary support if any problem has been encountered during the installation
processes. For more detailed information, please visit CINO website.
11
Getting Started
Establish SPP Slave Connection
Ensure the battery is fully charged and a virtual COM port is available in your remote host for connecting the scanner. If
not, please go to the folder “Client Applications” located in Bluetooth Advanced Setting. Click the “Add COM Port” to
add one more Bluetooth COM port.
Power on or wake up the scanner by pressing the Trigger key within radio coverage if the scanner is power-off state, and
ensure the status indicator of scanner blinks red and green alternatively (in “Uninstall” state). If the scanner is not in
uninstall state, please scan the “Uninstall” command first. Then scan the “SPP Slave Mode” command, and the link
indicator of scanner will blink blue 3 times per 2 seconds during searching process.
Uninstall
SPP Slave Mode
You have to execute the Bluetooth Discovery procedure to find all available Bluetooth device list in your remote host. You
will see ‘F(L/A)xxxBT-xxxx’’ or ‘PF(L/A)xxxBT-xxxx’’ is shown in the list if the scanner is successfully discovered.
Wireless FuzzyScan
Reference Manual
Double click the “F(L/A)xxxBT-xxxx” or ‘PF(L/A)xxxBT-xxxx’’ on the discovered Bluetooth devices. If the PIN Code or
Passkey is requested for security connection, please enter “00000000” (default setting). You will see “Serial Port on
F(L/A)xxxBT-xxxx” or ‘PF(L/A)xxxBT-xxxx’’. Please double click this SPP service to establish the connection between
scanner and remote host device.
The scanner will emit 4 beeps in ascending tone to indicate the connection is established. At the same time, the link
indicator of scanner will blink blue once per 2.5 seconds to indicate the scanner is in radio-connected state.
Please note that if the scanner is not connected to the host device within 1 minute after scanning the “SPP Slave Mode”
command, the scanner will go off automatically. You can just press the trigger to wake up the scanner to continue the
installation.
The above procedures are based on popular Windows environment. But the installation procedures may vary
depending on different remote host devices, operating systems and the Bluetooth software drivers. Please consult your
professional IT consultant to obtain necessary support if any problem has been encountered during the installation
processes. For more detailed information, please visit CINO website.
12
Getting Started
Enter Bluetooth Discoverable Mode (only available for pocket scanners)
If you use pocket scanner, you can have the scanner entered into Bluetooth discoverable mode for pairing with any remote
host easily. When you press and hold the FN1 for more than 3 seconds, the scanner will enter into preset Bluetooth
discoverable mode. You have to carry out the Bluetooth discovery procedure to find the scanner for pairing. The preset
Bluetooth profile for discoverable mode is “HID Mode”. You can change the Bluetooth profile to “HID Mode with Passkey” or
“SPP Slave Mode”.
Out-of-range Scanning
When the radio connection is established between scanner and remote host device, the scanner will transmit each scanned
data right after scanning the barcode. However, the scanner is preset not to scan any barcode data when it loses the radio
connection with the remote host device.
If you enable the out-of-range scanning function, the scanner is able to continue scanning barcode data while it is out of
radio coverage. All scanned data will be temporarily stored into the memory buffer until radio link resumed.
Disable Out-of-range Scanning ◆
Wireless FuzzyScan
Reference Manual
Enable Out-of-range Scannning
In case of the scanner is out of radio coverage, you will hear 4 beeps in descending tone to indicate the radio connection lost.
The link indicator of scanner will blink blue 3 times per 2 seconds. Once the scanner is back to radio coverage, you will
hear 4 beeps in ascending tone to indicate the radio connection rebuilt and the scanner will blink blue once per 2.5
seconds. At the same time, all stored scanned data will be transmitted automatically right after the radio link is resumed.
Power Off
By default, the scanner goes off if the scanner is not used during the user-defined time out duration. You also can power off
the scanner by long pressing and holding Right Key for more than three seconds or scanning the “Power Off” command.
If you would like to activate the scanner, please press the trigger key.
Power Off
13
Getting Started
Batch Scanning (Inventory Mode)
Thanks to the specially designed Batch Scanning function, the scanner is capable of storing the barcode data. It is an ideal
cost-saving solution for inventory applications.
Once you scan the ““Enter Batch Scanning” command to activate this function, all scanned barcode data will be stored into
the memory storage, and the status indicator of scanner will give green blink at regular interval during batch scanning. You
can scan and store the barcode data till the memory storage is full. If the storage is full, you will hear 2 long beeps and the
status indicator will give 2 red blinks to indicate out of storage.
If you use pocket scanner, you can also press and hold the Function Key 2 for more than 3 seconds to enter Batch
Scanning, by which 3 beeps will be heard and the status indicator of the scanner will blink green at regular interval during
batch scanning.
To exit the batch scanning, please scan the “Exit Batch Scanning” command. If you use pocket scanner, you can also exit
the batch scanning by pressing and holding Function Key 2 for more than 3 seconds.
Enter Batch Scanning
Exit Batching Scanning
Wireless FuzzyScan
Reference Manual
Using Quantity Feature
The scanner supports quantity feature when it enters batch scanning. When you use quantity feature, the quantity
information and scanned barcode data will be stored into the memory storage together. You can enter the quantity
information from 1 to 9999 by scanning the following quantity commands right after you scanned the barcode data.
Quantity 0
Quantity 5
Quantity 3
Quantity 8
Quantity 1
Quantity 6
Quantity 4
Quantity 9
Quantity 2
Quantity 7
14
Getting Started
There are three ways to output the stored barcode data and quantity information. The preset output format is to transmit
stored data as many times as the quantity indicated.But you still can set the scanner to output stored barcode data together
with quantity information in two fields, and a preset delimter”，” will be output in between. To fulfill different application
requirements, both the delimiter and output sequency can be changed as well.
As many times as the quantity indicates ◆
<Quantity><Field Delimiter><Scanned Data>
<Scanned Data><Field Delimiter><Quantity>
How to Transmit Stored Data
The scanner is preset to transmit all the stored data by scanning the “Transmit Stored Data” command. If you use pocket
scanner, you can also transmit the stored data by pressing and holding Left Key for more than 3 seconds. During the
transmission, the scanner will emit continuous short clicks and the link indicator will blink blue. Then the scanner will emit
two short beeps after data transmission is completed.
Wireless FuzzyScan
Reference Manual
Transmit Stored Data
But you are able to transmit the stored data by placing the scanner onto the cradle as well.
Scan Barcode Command ◆
Place Scanner onto the Cradle
Scan command or Place Scanner onto theCradle
15
Getting Started
How to Delete Scanned Data
The scanner is preset to keep all the stored data until you scan the “Clear All Stored Data” command. But you are still able to
change the setting to “Auto Delete Stored Data after Transmission” as well.
Clear All Stored Data
Auto Delete Stored Data
after Transmission
Keep Stored Data after
Transmission ◆
How to Delete Last Scanned Data
Wireless FuzzyScan
Reference Manual
If you scanned a wrong barcode, the last scanned data can be deleted by scanning the ‘’Delete Last Scanned Data’’
command. If you use pocket scanner, you can also delete the last scanned data by short pressing the FN2.
Delete Last Scanned Data
16
Getting Started
Simultaneous Barcode Scanning and On-screen Keyboard
You can use barcode scanning and on-screen keyboard of the mobile device simultaneously. To activate the on-screen
keyboard function, you can turn off the radio by scanning “Switch On-screen Keyboard” command. If you use pocket
scanner, you can turn off the radio to activate the on-screen keyboard by short pressing the FN1 Once you finished the
keyboard input, pressing the trigger once to turn on the radio, the on-screen keyboard will be inactivated.
The scanner is preset to use “General Approach” by controlling the radio to toggle between barcode scanning and on-screen
keyboard of most popular mobile devices. To work with iOS devices, please scan “iOS Approach” command to activate this
function first. If you use pocket scanner, the FN1 can be set to “iOS Approach” to quickly toggle iOS on-screen keyboard.
Then you can scan “Switch On-screen Keyboard” command to toggle the iOS on-screen keyboard. For pocket scanner, you
can also toggle the iOS on-screen keyboard by short pressing the FN1.
General Approach ◆
iOS Approach
Switch On-screen Keyboard
Wireless FuzzyScan
Reference Manual
Above function is available for FuzzyScan Bluetooth Cordless Scanner:
One of following Bluetooth scanners with proper firmware preload:
Bluetooth Image Scanners
F680BT / F780BT : Rev. 4.00.05 and above
L680BT / L780BT:
Rev. 4.00.05 and above
A770BT :
Rev. 1.00.14 and above
Rev. 2.00.02 and above
Bluetooth Pocket Scanners:
PF680BT / PL680BT :
Rev. 1.00.05 and above
PA670BT :
Rev. 1.00.01 and above
17
Getting Started
Presentation Scanning (Gun type only)
The Presentation Scanning is designed for hand-free applications for user’s convenience. If the “Presentation Scanning
Auto-sense” function is enabled, the scanner is capable of automatically switching to presentation mode as soon as you
place it onto the SmartStand or cradle.
Disable Auto-sense ◆
Enable Auto-sense
Check Battery Status
You can check battery status of the scanner by short pressing the Left Key or scanning “Check Battery Status” command.
Please refer to the “Battery Status Indication” shown on page 1 for details.
Check Battery Status
Battery Status Indication
The following corresponding flashes of the LED indicators present the current battery status of the scanner.
Wireless FuzzyScan
Reference Manual
LED Indication
Battery Status
3 green and blue flashes
More than 75%
3 green flashes
More than 50%
3 orange flashes
More than 25%
3 red flashes
Less than 25%
Paging Function
The Paging function is helpful for you to locate the paired smart cradle or scanner. If you would like to page the paired smart
cradle, you can scan “Paging” command. If you would like to page the paired scanner, you can press the paging/reset button
of the smart cradle no longer than 3 seconds.
Paging
Paging/Reset Button
18
Configure Your FuzzyScan
Bar Code Programming Menu
The FuzzyScan bar code commands are specially designed
Proprietary bar code labels which allow you to set the
FuzzyScan internal programming parameters. There are
System Command, Family Code and Option Code for
programming purpose.
Wireless FuzzyScan
Reference Manual
Each programmable family and bar code command label is
listed on the same page with major system commands. The
detailed explanations and special programming flowchart are
printed on facing or following pages. You can read the
explanation and set the FuzzyScan concurrently.
A supplemental bar code command menu incorporates the
bar code command labels of System Command and Option
Code. As you set the FuzzyScan, open the bar code
command menu to find the option code page. You may scan
the desired family code and option code to set FuzzyScan. If
you want to change the programming family for multiple
settings, you need only turn over the programming page to
find next desired programming family.
19
System Command
The System Command is the highest level bar code
command which directs FuzzyScan to perform immediate
operations, such as entering programming mode
(PROGRAM), exiting programming mode (EXIT), listing
system information (SYSLIST), recovering to factory
preset configurations (M_DEFAULT), and so on. Please
note that all system commands will take a few seconds to
complete the operations. User must wait for the
completion beeps before scanning another bar code.
Family Code
The Family Code is scanned to select the user desired
programming family. FuzzyScan has already provided
more than one hundred programming families to meet any
specific requirements.
Option Code
The Option Codes is a set of bar code commands
represented by “0–9”, “A–F” and finishing selection (FIN).
For most setting, you must select at least one option code
following the family code selection to set the desired
parameter for the selected programming family.
Configure Your FuzzyScan
Programming Procedures
If the programming family must take multiple scans
selection, cycling scan selection, or dual level selection
procedures, the family of the programming menu will be
marked with the matched representing symbol of
Programming Category (P.C.) in bold font listed in the
following table. You can easily find the bold mark in the
programming menu, and refer to their flowcharts for details.
Before setting the FuzzyScan, please also refer to the
“Beeping Indications” listed in Appendix to understand the
details of programming beeping indications. It will be very
helpful for you to know the existing status while you are
programming the FuzzyScan.
Wireless FuzzyScan
Reference Manual
As you scan the bar code command to select the desired
parameters, information about the final selected parameters
represented by the bar code commands are stored in the
FuzzyScan’s internal Flash Memory ASIC or non-volatile
memory. If you turn off the unit, the Flash Memory ASIC or
non-volatile memory retains all programming options. You
need not re-program the FuzzyScan if you want to keep the
existing configurations in the next power on.
The programming procedures of FuzzyScan are designed
as simple as possible for ease of setting. Most
programming families take the Single Scan Selection
programming procedure. But several programming families
have more complex and flexible programmable options,
and you must take Multiple Scans Selection, Cycling
Scan Selection or Dual Level Selection to complete their
programming procedures. Each kind of programming
procedure is listed in the following pages for your reference.
Please give careful attention to become familiar with each
programming procedure.
Conventions of Programming Menu
Conventions
Descriptions
Factory Default Value
P.C.
Programming Category
SS : Single scan selection
MS : Multiple scans selection
CS : Cycling scan selection
DS : Dual level scan selection
20
(
)
Necessary Option Code
[
]
Selectable Option Code
Configure Your FuzzyScan
Program & End
System List, Group & Master Default
Scan
“PROGRAM”
Scan
“SYSLIST”
FuzzyScan will enter programming mode,
and inhibit all non-programming functions.
FuzzyScan will list the product information and
revision number to host via selected host interface,
Wireless FuzzyScan
Reference Manual
then issue the completion beeping.
Scan
“END”
Scan
“M_DEFAULT”
FuzzyScan will exit programming mode, and store all
parameters in Flash Memory ASIC or non-volatile memory,
then issue the completion beeping.
parameters into factory preset configurations,
then issue the completion beeping.
FuzzyScan will recover all programmable
Please note that the FuzzyScan will take 3-4 seconds to
store parameters in internal Flash Memory ASIC or
non-volatile memory after you scan the “END”. Please
don’t turn off the power before the completion beeping. It
may destroy all configured parameters.
21
Configure Your FuzzyScan
Single scan selection
Scan
“PROGRAM”
Multiple scans selection
Scan
“PROGRAM”
Enter programming mode.
Select one of desired
Select one of desired
Scan
One of Family Codes
Scan
One of Family Codes
programming families.
programming families.
1. Select one or several
Select one option code of
Scan
One of Option Codes
Enter programming mode.
Scan One or
Several Option Codes
desired parameter.
option codes to select
desired parameters.
2. If it’s necessary, scan
“FIN” to terminate
Yes
Yes
Want to select another
Repeat
Selection
programming family?
Repeat
Selection
option code selection.
Wireless FuzzyScan
Reference Manual
Want to select another
No
No
Scan
“END”
Scan
“END”
Exit programming mode.
22
programming family?
Exit programming mode.
Configure Your FuzzyScan
Cycling scan selection
Dual level selection
Scan
“PROGRAM”
Scan
“PROGRAM”
Enter programming mode.
Select one of desired
Scan
One of Family Codes
Scan
One of Family Codes
programming families.
Cycling select one or
Scan
One of Option Codes
several option codes of
desired parameters as
(2nd) Scan One or
Several Option Codes
Wireless FuzzyScan
Reference Manual
Scan “FIN”
of desired parameters.
1. Select one or several
parameters.
2. If it’s necessary, scan
Finish cycling selection.
“FIN” to terminate
(If necessary)
option code selection.
Yes
Want to select another
Repeat
Selection
programming family?
Want to select another
programming family?
No
Scan
programming families.
option codes of desired
scans selection.
Repeat
Selection
Select one of desired
Select several option codes
(1st) Scan
Several Option Codes
“Single” or “Multiple”
Yes
Enter programming mode.
No
Scan
“END”
Exit programming mode.
“END”
23
Exit programming mode.
Configure Your FuzzyScan
Host Interface Selection
PROGRAM
Family Code Selection
F_DEFAULT
P.C
Parameter Selection
MS
IBM PS/2, 25-30 series keyboard wedge interface
MS
Standard/TTL RS-232 peer-to-peer serial
MS
Wand emulation
MS
USB Com Port Emulation
MS
PS/2 (DOS/V) direct link (keyboard replacement)
MS
PS/2 (DOS/V) keyboard wedge turbo mode
MS
PS/2 (DOS/V) keyboard wedge standard mode
MS
Laser emulation
MS
USB HID standard mode
MS
USB HID turbo mode
MS
USB HID Legacy
MS
USB EFT Terminal Mode
A series doesn’t support Wand emulation, Laser emulation, USB HID Legacy and USB EFT Terminal Mode.
Wireless FuzzyScan
Reference Manual
Host Interface Selection
24
Option Code
02
06
08
09
10
13
14
17
18
19
20
21
Configure Your FuzzyScan
Symbology Reading Control
Wireless FuzzyScan
Reference Manual
♦ User Defined Symbol ID ♦
PROGRAM
Family Code Selection
P.C
Symbol ID : 1 character
DS
Option Code
F DEFAULT
2nd Option Code
Code 128 (default=B)
GS1-128 (default=C)
UPC-A (default=A)
EAN-13 (default=F)
Codabar/NW-7 (default=D)
Code 39/Code 32 (default=G)
Code 93 (default=H)
Standard/Industrial 2 of 5 (default=I)
Interleaved 2 of 5 (default=J)
Matrix 2 of 5 (default=K)
China Postal Code (default=L)
German Postal Code (default=M)
IATA (default=O)
Code 11 (default=P)
MSI/Plessey (default=R)
UK/Plessey (default=S)
Telepen (default=T)
GS1 DataBar (default=X)
UPC-E (default=E)
EAN-8 (default=N)
Trioptic Code 39 (default=W)
UCC Coupon Extended Code (default=Z)
PDF417/Micro PDF417 (default=V)
Codablock F (default=Y)
Code 16K (default=Q)
Code 49 (default=U)
Korea Post Code (default=a)
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
QR & Micro QR Code (default=b)
Data Matrix (default=c)
28
29
30
(1 character)
(1 character)
(1 character)
Parameter Selection
Maxi Code (default=d)
25
Configure Your FuzzyScan
Symbology Reading Control
♦ User Defined Symbol ID ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Symbol ID : 1 character
DS
Parameter Selection
Aztec Code (default=e)
Chinese Sensible (default=f)
Australian Post (default=g)
British Post (default=h)
Intelligent Mail (USPS 4CB/One Code) (default=j)
Japan Post (default=k)
Netherlands KIX Post (default=l)
US Planet (default=m)
US Postnet (default=o)
26
Option Code
2nd Option Code
31
32
33
34
36
37
38
39
41
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
(1 character)
Configure Your FuzzyScan
Symbology Reading Control
♦ Symbology ID Transmission ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Symbology ID Transmission
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Disable symbology ID transmission
Enable prefix CINO symbology ID transmission
Enable suffix CINO symbology ID transmission
Enable both prefix and suffix CINO symbology ID transmission
Enable prefix AIM symbology ID transmission
Enable suffix AIM symbology ID transmission
Enable both prefix and suffix AIM symbology ID transmission
27
Option Code
0
1
2
3
4
5
6
Configure Your FuzzyScan
Symbology Reading Control
♦ Readable Bar Code Setting ♦
PROGRAM
Family Code Selection
Readable Symbology Setting
Remember to scan “FIN” to terminate
this selection. But if you select the
“Auto”, FuzzyScan will terminate this
Wireless FuzzyScan
Reference Manual
selection automatically.
F_DEFAULT
P.C
SS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
CS
Parameter Selection
Option Code
00
01
31
02
03
04
05
06
07
47
08
38
48
58
68
09
10
11
12
13
14
15
17
18
19
20
21
A0
A1
A2
A3
A4
Auto
Code 128 *
GS1-128 *
UPC-A *
UPC-E *
EAN-13 *
EAN-8 *
Codabar/NW-7 *
Code 39 *
Trioptic Code 39
Standard/Industrial 2 of 5
Matrix 2 of 5
Interleaved 2 of 5 *
China Postal Code
Germany Postal Code
Code 93 *
Code 11
MSI/Plessey
UK/Plessey
Telepen
GS1 DataBar (RSS-14) *
IATA
PDF417 * /Micro PDF417
Codablock F
Code 16K
Code 49
Korea Post Code
QR Code */ Micro QR Code *
Data Matrix *
MaxiCode
Aztec Code *
Chinese Sensible (Han Xin) Code
28
Configure Your FuzzyScan
Symbology Reading Control
♦ Readable Bar Code Setting ♦
PROGRAM
Family Code Selection
F_DEFAULT
P.C
Parameter Selection
Option Code
Wireless FuzzyScan
Reference Manual
B0
Australian Post
CS
Readable Symbology Setting
B1
British Post
CS
B3
Intelligent Mail barcode
CS
B4
Japanese Post
CS
B5
KIX Post
CS
B6
Planet Code
CS
B8
Postnet
CS
If your application is known, you may select those known symbologies only to increase the reading speed and decrease the possibility of reading error. Furthermore, to add
the “Symbology ID” into the transmitted data is also helpful to identify the specific symbology.
Above symbologies marketed with * are enabled as default. When you select “Auto”, the scanner only reads those symbologies marked with *.
When you set the minimum and maximum length of each symbology, please note the data length of scanned bar code doesn’t include start/stop characters.
29
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 39/Code 32 Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Code 39 Family Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Code 39
Enable Code 39
Select Standard Code 39 as primary format
Select Full ASCII Code 39 as primary format
Select Code 32 (PARAF, Italian Pharmaceutical) as primary format
Disable start/stop symbol transmission
Enable start/stop symbol transmission
Disable Code 32 leading A transmission
Enable Code 32 leading A transmission
Disable MOD 43 check digit verification
Enable MOD 43 check digit verification
Disable check digit transmission
Enable check digit transmission
Disable Code 39 buffering
Enable Code 39 buffering
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
Trioptic Code 39 Setting
SS
SS
Disable Trioptic Code 39
Enable Trioptic Code 39
0
1
Code 39 Min. Length
SS
MS
Default (01)
01-Maximum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 39 Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously.
30
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 39 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Code 39 Security Level
SS
SS
SS
SS
Parameter Selection
Level 0
Level 1
Level 2
Level 3
Option Code
0
1
2
3
Wireless FuzzyScan
Reference Manual
Code 39 Security Level
The scanner offers four levels of decode security for Code39 bar codes:
Level 0: If you are experiencing misread of poorly-printed or serious out-of-spec. bar codes in level 1, please select level 0.
Level 1: If you are experiencing misread of poorly-printed or out-of-spec. bar codes in level 2, please select level 1.
Level 2: This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding “in-spec” Code39 bar codes.
Level 3: If you failed to read poorly-printed or out-of-spec. bar codes in level 2, please select level 3. This is the most aggressive setting and may increase the misread.
31
Configure Your FuzzyScan
Symbology Reading Control
♦ Codabar/NW-7 Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Codabar Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Codabar
Enable Codabar
Select Codabar standard format
Select Codabar ABC format
Select Codabar CLSI format
Select Codabar CX format
Disable start/stop symbol transmission
Enable ABCD/ABCD start/stop symbol transmission
Enable abcd/abcd start/stop symbol transmission
Enable ABCD/TN*E start/stop symbol transmission
Enable abcd/tn*e start/stop symbol transmission
Disable check digit verification
Enable check digit verification
Disable check digit transmission
Enable check digit transmission
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
Codabar Check Digit Settings
SS
SS
SS
SS
SS
SS
SS
Modulus 16
Modulus 10/weight 3
Modulus 11
Modulus 10/weight 2
7 check DR
Weight Modulus 11
Runes (Modulus 10/weight 2)
0
1
2
3
4
5
6
Codabar Min. Length
SS
MS
Default (04)
01-Maximum
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
32
Configure Your FuzzyScan
Symbology Reading Control
♦ Codabar/NW-7 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Codabar Max. Length
SS
MS
Parameter Selection
FIN
(2 digits)
Default (98)
98-Minimum
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Option Code
33
Configure Your FuzzyScan
Symbology Reading Control
♦ UPC-A & UPC-E Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC Family Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Option Code
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
Disable UPC-A
Enable UPC-A
Disable UPC-E
Enable UPC-E
Disable UPC-E expansion
Enable UPC-E expansion
Disable UPC standardization
Enable UPC standardization
Disable UPC numeric system
Enable UPC numeric system
Disable UPC-A check digit transmission
Enable UPC-A check digit transmission
Disable UPC-E check digit transmission
Enable UPC-E check digit transmission
Disable UPC “leading 1” portion
Enable UPC “leading 1” portion
When enable UPC-E expansion, the UPC-E decoded data will be converted to UPC-A format and affected by related setting, such as UPC standardization, UPC numeric
system, UPC-A check digit transmission.
UPC-E & EAN-8 Expansion
: Expand the 8-digit UPC-E and 8-digit ENA-8 to 12-digit UPC-A and 13-digit EAN-13.
UPC-A/E Standardization
: Expand the 12-digit UPC-A to 13-digit EAN-13 with 1 zero insertion.
UPC Lead 1 Numeric System
: Enable to read UPC leading with the 1 numeric system, you must enable this option.
WPC Selection
(UPC/EAN/CAN)
UPC-A
UPC-E
EAN-13
EAN-8
Basic Length
Disable
Check Digit
Disable
Numeric System
With 2-digit
Addendum
With 5-digit
Addendum
Enable
Standardization
Enable
Expansion
12
8
13
8
-1
-1
-1
-1
-1
-1
NC
NC
+2
+2
+2
+2
+5
+5
+5
+5
+1
+1
NC
NC
0
+4
0
+5
34
Configure Your FuzzyScan
Symbology Reading Control
♦ UPC-A & UPC-E Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC Supplement Setting
SS
SS
SS
SS
SS
SS
SS
SS
Select UPC without supplement digits
Select UPC with only 2 supplement digits
Select UPC with only 5 supplement digits
Select UPC with 2/5 supplement digits
Disable force supplement digits output
Enable force supplement digits output
UPC Family Addenda Separator Off
UPC Family Addenda Separator On
0
1
2
3
4
5
6
7
UPC/EAN Security Level
SS
SS
Level 0
Level 1
Level 2
0
1
SS
Parameter Selection
Option Code
2
Only available for UPC-A & EAN-13
Wireless FuzzyScan
Reference Manual
Supplement Scan Voting
SS
SS
SS
SS
SS
SS
SS
None
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
Level 11
Level 12
Level 13
0
1
2
3
4
5
6
7
8
9
A
B
C
D
UPC/EAN Security Level
The scanner offers three levels of decode security for UPC/EAN bar codes:
Level 0: If you are experiencing misread of poorly-printed or out-of-spec. bar codes, especially in characters 1, 2, 7, and 8 in level 1, please select level 0. Selection of this
security level may significantly impair the decoding ability of the scanner.
Level 1: This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding “in-spec” UPC/EAN bar codes.
Level 2: If you are experiencing misread of poorly-printed, soiled or damage bar codes in level 1, please select level 2. This is the most aggressive setting and may
increase the misread.
The Supplement Scan Voting is the number of times the same UPC/EAN with 2/5 supplement digits has to be decoded before it is transmitted. It is helpful when decoding
a mix of UPC/EAN symbols with and without supplement digits. This function is effective when you select UPC/EAN with only 2 supplement digits, UPC/EAN with only 5
supplement digits or UPC/EAN with 2/5 supplement digits. The default value is Level 3. When you select higher level, it may impact the reading speed on poorly-printed,
low contrast or damage barcode labels.
35
Configure Your FuzzyScan
Symbology Reading Control
♦ EAN Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
EAN Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable EAN-13
Enable EAN-13
Disable EAN-8
Enable EAN-8
Disable EAN-8 expansion
Enable EAN-8 expansion
Disable EAN-13 check digit transmission
Enable EAN-13 check digit transmission
Disable EAN-8 check digit transmission
Enable EAN-8 check digit transmission
Disable ISBN/ISSN Conversion reading check
Enable ISBN/ISSN Conversion reading check
0
1
2
3
4
5
6
7
8
9
A
B
EAN Supplement Setting
SS
SS
SS
SS
SS
SS
SS
SS
Select EAN without supplement digits
Select EAN with only 2 supplement digits
Select EAN with only 5 supplement digits
Select EAN with 2/5 supplement digits
Disable force supplement digits output
Enable force supplement digits output
EAN Addenda Separator Off
EAN Addenda Separator On
0
1
2
3
4
5
6
7
Supplement Scan Voting
SS
SS
SS
SS
SS
SS
SS
None
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Level 8
Level 9
Level 10
Level 11
Level 12
Level 13
Option Code
0
1
2
3
4
5
6
7
8
9
A
B
C
D
The Supplement Scan Voting is the number of times the same UPC/EAN with 2/5 supplement digits has to be decoded before it is transmitted. It is helpful when decoding
a mix of UPC/EAN symbols with and without supplement digits. This function is effective when you select UPC/EAN with only 2 supplement digits, UPC/EAN with only 5
supplement digits or UPC/EAN with 2/5 supplement digits. The default value is Level 3. When you select higher level, it may impact the reading speed on poorly-printed,
low contrast or damage barcode labels.
36
Configure Your FuzzyScan
Symbology Reading Control
♦ EAN Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UPC/EAN Security Level
SS
SS
SS
Parameter Selection
Option Code
0
1
Level 0
Level 1
Level 2
2
Only available for UPC-A & EAN-13
Wireless FuzzyScan
Reference Manual
EAN Supplement Control
SS
SS
SS
SS
SS
SS
SS
SS
Disable all specific prefix supplement digital output
Enable all specific prefix supplement digital output
Enable 491 Supplement Digit Output
Enable 978/979 Supplement Digit Output
Enable 977 Supplement Digit Output
Enable 378/379 Supplement Digit Output
Enable 414/419 Supplement Digit Output
Enable 434/439 Supplement Digit Output
0
1
2
3
4
5
6
7
UPC/EAN Security Level
The scanner offers three levels of decode security for UPC/EAN bar codes:
Level 0: If you are experiencing misread of poorly-printed or out-of-spec. bar codes, especially in characters 1, 2, 7, and 8 in level 1, please select level 0. Selection of this
security level may significantly impair the decoding ability of the scanner.
Level 1: This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding “in-spec” UPC/EAN bar codes.
Level 2: If you are experiencing misread of poorly-printed, soiled or damage bar codes in level 1, please select level 2. This is the most aggressive setting and may
increase the misread.
EAN Supplement Control
If you select EAN with only 2, or 5 or 2/5 supplement digits and enable 491 prefix supplement digit output, the scanner will transmit EAN with 2, or 5 or 2/5 supplement
digits bar codes starting with 491 prefix. The EAN without supplement digit will not be transmitted.
If you select EAN with only 2, or 5 or 2/5 supplement digits and enable the other except 491 prefix supplement digit output, the scanner will transmit EAN with 2, or 5, or 2/5
supplement digits bar codes starting with specific prefix. The EAN without supplement digit will be transmitted.
37
Configure Your FuzzyScan
Symbology Reading Control
♦ UCC Coupon Extended Code Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
UCC Coupon Extended Code
SS
SS
Parameter Selection
Disable UCC Coupon Extended Code
Enable UCC Coupon Extended Code
Option Code
0
1
Wireless FuzzyScan
Reference Manual
UCC Coupon Extended Code
When UCC coupon extended code function is enabled, scanner decodes UPC-A barcodes starting with digit “5”, EAN-13 barcodes starting with digit “99” and GS1-128
Coupon Codes. UPC-A, EAN-13 and EAN-128 must be enabled to scan all types of Coupon Codes.
38
Configure Your FuzzyScan
Symbology Reading Control
♦ IATA & Interleaved 2 of 5 Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
IATA Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable IATA
Enable IATA
Select 15-digit fixed length IATA checking
Select variable length IATA
Disable check digit verification
Enable check digit automatic verification
Enable S/N checking digit verification only
Enable CPN checking digit verification only
Enable CPN, Airline and S/N check digit verification
Disable check digit transmission
Enable check digit transmission
Disable start/stop symbol transmission
Enable start/stop symbol transmission
0
1
2
3
4
5
6
7
8
9
A
B
C
Interleaved 2 of 5 Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Interleaved 2 of 5
Enable Interleaved 2 of 5
Select Interleaved 2 of 5 as primary format
Select German Postal Code as primary format
No check character
Validate USS check digit
Validate OPCC check digit
Disable check digit transmission
Enable check digit transmission
0
1
2
3
4
5
6
7
8
39
Option Code
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 25 Family Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 25 Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Disable Standard/Industrial 2 of 5
Enable Standard/Industrial 2 of 5
Disable Matrix 2 of 5
Enable Matrix 2 of 5
Disable China Postal Code
Enable China Postal Code
Disable check digit verification
Enable check digit verification
Disable check digit transmission
Enable check digit transmission
Code 25 Family Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
7
8
9
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
Code 25 Family Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
For Code25 setting, we recommend you to select only one type of Code 25 or set the maximum/minimum bar code length. To decode all types of Code 25 or to variable
length of Code 25 will increase the possibility of reading error.
40
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 11 & Code 93 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 11 Setting
SS
SS
SS
SS
SS
SS
SS
Disable Code 11
Enable Code 11
Disable check digit verification
Select 1-check digit verification
Select 2-check digit verification
Disable check digit transmission
Enable check digit transmission
Code 11 Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 11 Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 93 Setting
SS
SS
SS
SS
Disable Code 93
Enable Code 93
Disable check digit transmission
Enable check digit transmission
Code 93 Min. Length
SS
MS
Default (01)
01-Maximum
0
1
2
3
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 93 Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
41
Configure Your FuzzyScan
Symbology Reading Control
♦ MSI/Plessey Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
MSI/Plessey Setting
SS
SS
SS
SS
SS
SS
SS
Disable MSI/Plessy
Enable MSI/Plessy
Select MOD 10 check digit
Select MOD 10-10 check digit
Select MOD 11-10 check digit
Disable check digit transmission
Enable check digit transmission
MSI/Plessey Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
MSI/Plessey Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
42
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 128 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 128 Setting
SS
SS
SS
SS
Disable Code 128 and GS1-128
Enable Code 128 and GS1-128
ISBT Concatenation Off ISBT Concatenation On
Code 128 Min. Length
SS
MS
Default (01)
01-Maximum
Option Code
0
1
2
3
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Code 128 Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
Code 128 Security Level
SS
SS
Level 0
Level 1
0
1
Code 128 Security Level
The scanner offers two levels of decode security for Code128 bar codes:
Level 0: If you are experiencing misread of poor-printed or out-of-spec. bar code in level1, please select level 0.
Level 1: This is the default setting which allows the scanner to operate fastest, while providing sufficient security in decoding "in-spec." Code128 bar codes.
43
Configure Your FuzzyScan
Symbology Reading Control
♦ GS1-128 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
GS1-128 Setting
SS
SS
Disable GS1-128
Enable GS1-128
GS1-128 Min. Length
SS
MS
Default (01)
01-Maximum
Option Code
0
1
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
GS1-128 Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
44
Configure Your FuzzyScan
Symbology Reading Control
♦ UK/Plessey Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
UK/Plessey Setting
SS
SS
SS
SS
SS
SS
SS
SS
Disable UK/Plessey
Enable UK/Plessey
Select UK/Plessey Standard Format
Select UK/Plessey CLSI Format
Disable Convert X to A-F
Enable Convert X to A-F
Disable check digit transmission
Enable check digit transmission
UK/Plessey Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
6
7
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
UK/Plessey Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
45
Configure Your FuzzyScan
Symbology Reading Control
♦ Telepen Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Telepen Setting
SS
SS
SS
SS
SS
SS
Disable Telepen
Enable Telepen
Select Telepen Numeric mode
Select Telepen Full ASCII mode
Disable check digit transmission
Enable check digit transmission
Telepen Min. Length
SS
MS
Default (04)
01-Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Telepen Max. Length
SS
MS
FIN
(2 digits)
Default (98)
98-Minimum
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
46
Configure Your FuzzyScan
Symbology Reading Control
♦ GS1 DataBar Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
GS1 DataBar Setting
SS
SS
SS
SS
SS
SS
Disable GS1 DataBar (RSS-14)
Enable GS1 DataBar (RSS-14)
Disable GS1 DataBar Limited
Enable GS1 DataBar Limited
Disable GS1 DataBar Expanded
Enable GS1 DataBar Expanded
GS1 DataBar Min. Length
SS
MS
Default (04)
01- Maximum
Option Code
0
1
2
3
4
5
FIN
(2 digits)
Only available for Expanded GS1 Databar.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
GS1 DataBar Max. Length
SS
MS
FIN
(2 digits)
Default (74)
74-Minimum
Only available for Expanded GS1 Databar.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
47
Configure Your FuzzyScan
Symbology Reading Control
♦ Composite Codes, Codablock F
PDF417/MicroPDF417 & Setting ♦
PROGRAM
Family Code Selection
P.C
Composite Codes Setting
SS
SS
SS
SS
Parameter Selection
Disable composite codes
Enable composite codes
UPC Composite Mode: UPC never linked
UPC Composite Mode: UPC always linked
F_DEFAULT
Option Code
0
1
2
3
If UPC Composite Mode: UPC never linked is selected, UPC barcodes are
transmitted whether MicroPDF417 symbol is detected or not.
Wireless FuzzyScan
Reference Manual
If UPC Composite Mode: UPC always linked is selected, UPC barcodes are only
transmitted when the MicroPDF417 is detected.
Codablock F Setting
SS
SS
Disable
Enable
0
1
PDF417/Micro PDF417 Setting
SS
SS
SS
SS
Disable PDF417
Enable PDF417
Disable MicroPDF417
Enable MicroPDF417
0
1
2
3
48
Configure Your FuzzyScan
Symbology Reading Control
♦ Code 16K & Code 49 Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Code 16K Setting
SS
SS
Disable Code 16K
Enable Code 16K
Code 16K Min. Length
SS
MS
Default (01)
01-Maximum
Option Code
0
1
FIN
(3 digits)
Scan 3 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
Code 16K Max. Length
SS
MS
FIN
(3 digits)
Default (160)
160-Minimum
Wireless FuzzyScan
Reference Manual
Scan 3 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
Code 49 Setting
SS
SS
Disable Code 49
Enable Code 49
Code 49 Min. Length
SS
MS
Default (01)
01-Maximum
0
1
FIN
(2 digits)
Scan 2 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
Code 49 Max. Length
SS
MS
FIN
(2 digits)
Default (81)
81-Minimum
Scan 2 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
49
Configure Your FuzzyScan
Symbology Reading Control
♦ QR Code Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
QR Code Setting
SS
SS
QR Code Min. Length
SS
MS
Parameter Selection
Disable QR Code
Enable QR Code
Disable MicroQR Code
Enable MicroQR Code
Disable QR Code Append
Enable QR Code Append
Disable QR Code Inverse Reading
Enable QR Code Inverse Reading
Auto detect QR Code Inverse Reading
Default (01)
01-Maximum
Option Code
0
1
2
3
4
5
6
7
8
FIN
(4 digits)
Scan 4 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
Wireless FuzzyScan
Reference Manual
QR Code Max. Length
SS
MS
FIN
Default (7089)
7089-Minimum
Scan 4 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
50
(4 digits)
Configure Your FuzzyScan
Symbology Reading Control
♦ Data Matrix Setting ♦
PROGRAM
11Family Code Selection
Data Matrix Setting
Data Matrix Min. Length
F_DEFAULT
P.C
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
MS
Parameter Selection
Disable Data Matrix
Enable Data Matrix
Disable Data Matrix Inverse Reading
Enable Data Matrix Inverse Reading
Auto Detect Data Matrix Inverse Reading
Disable Data Matrix Mirror Images
Enable Data Matrix Mirror Images
Auto Detect Data Matrix Mirror Images
Option Code
0
1
4
5
6
7
8
9
FIN
(4 digits)
Default (01)
01-Maximum
Scan 4 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
Data Matrix Max. Length
SS
MS
FIN
(4 digits)
Default (3116)
3116-Minimum
Wireless FuzzyScan
Reference Manual
Scan 4 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
51
Configure Your FuzzyScan
Symbology Reading Control
♦MaxiCode Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
MaxiCode Setting
SS
Disable MaxiCode
0
SS
Enable MaxiCode
1
SS
MS
Default (01)
01-Maximum
MaxiCode Min. Length
Parameter Selection
Option Code
FIN
(3 digits)
Scan 3 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
MaxiCode Max. Length
SS
MS
Default (150)
150-Minimum
FIN
(3 digits)
Wireless FuzzyScan
Reference Manual
Scan 3 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
52
Configure Your FuzzyScan
Symbology Reading Control
♦ Aztec Code Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Aztec Code Setting
SS
SS
Disable Aztec Code
Enable Aztec Code
Aztec Code Min. Length
SS
MS
Default (01)
01-Maximum
Option Code
0
1
FIN
(4 digits)
Scan 4 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
Aztec Code Max. Length
SS
MS
FIN
(4 digits)
Default (3832)
3832-Minimum
Wireless FuzzyScan
Reference Manual
Scan 4 digits from the option code chart in Appendix; then FuzzyScan will terminate
this selection automatically.
53
Configure Your FuzzyScan
Symbology Reading Control
♦ Australian Post, US Planet, US Postnet,
British Post & Japan Post Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Option Code
Australian Post Setting
SS
SS
SS
SS
SS
SS
Disable Australian Post
Enable Australian Post
Raw format Output
Numeric Encoding Output (N Encoding Table)
Alphanumeric Encoding Output (C Encoding Table)
Auto-discriminate Output (Combination C & N Encoding Table)
0
1
2
3
4
5
US Planet Setting
SS
SS
SS
SS
Disable US Planet
Enable US Planet
Disable Check Digit Transmission
Enable Check Digit Transmission
0
1
2
3
US Postnet Setting
SS
SS
SS
SS
Disable US Postnet
Enable US Postnet
Disable Check Digit Transmission
Enable Check Digit Transmission
0
1
2
3
British Post Setting
SS
SS
SS
SS
Disable British Post
Enable British Post
Disable Check Digit Transmission
Enable Check Digit Transmission
0
1
2
3
Japan Post Setting
SS
SS
Disable Japan Post
Enable Japan Post
0
1
Australian Post Setting: Auto-discriminate output option increase the risk of misread because the encoded data format does not specify the Encoding Table used for
encoding.
54
Configure Your FuzzyScan
Symbology Reading Control
♦ Netherlands KIX Code, Intelligent Mail
& Korea Post Code Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Netherlands KIX Code Setting
SS
SS
Disable Netherlands KIX Code
Enable Netherlands KIX Code
0
1
Intelligent Mail Setting
(USPS 4CB/One Code)
SS
SS
Disable Intelligent Mail
Enable Intelligent Mail
0
1
Korea Post Code Setting
SS
SS
Disable
Enable
Length fixed in 6 characters.
0
1
55
Option Code
Configure Your FuzzyScan
Keyboard Interface Control
♦ Keyboard Layout (Language) Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Keyboard Layout
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Parameter Selection
Option Code
00
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
USA (QWERTY)
France (AZERTY)
Germany (QWERTZ)
United Kingdom - UK (QWERTY)
Canadian French (QWERTY)
Spain (Spanish, QWERTY)
Sweden/Finland (QWERTY)
Portugal (QWERTY)
Norway (QWERTY)
Spain (Latin America, QWERTY)
Italy (QWERTY)
Netherlands (QWERTY)
Denmark (QWERTY)
Belgium (AZERTY)
Switzerland-Germany (QWERTZ)
Iceland (QWERTY)
Japan (DOS/V)
Czech (QWERTY)
Please refer to the ASCII/HEX Table listed in the Appendix to determine HEX codes for characters, symbols, and functions to be used as preamble or postamble.
To set preamble or postamble as function key output, you must enable the “Function Key Emulation” feature as listed in page 3-25 first.
Keyboard Interface Message String :
Preamble
Data Length
Prefix Symbol ID
Scanned Data
Suffix Symbol ID
Postamble
Record Suffix
1-15 characters
2-4 digits
1 or 3 characters
Variable length
1 or 3 characters
1-15 characters
1 character
56
Configure Your FuzzyScan
Keyboard Interface Control
♦ Record Suffix, Preamble, Postamble,
FNC1 Transmit & Caps Lock ♦
PROGRAM
Family Code Selection
P.C
Parameter Selection
Record Suffix
SS
SS
SS
SS
SS
SS
None
RETURN
TAB
SPACE
ENTER (Numeric Key Pad)
User defined character (1 character)
Preamble
SS
MS
None
1-15 characters
F_DEFAULT
Option Code
0
1
2
3
4
5, (00-7F)
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
None
1-15 characters
FIN
[00-7F], [FIN]
Wireless FuzzyScan
Reference Manual
Maximum 15-character input; scan “FIN” to terminate this selection.
FNC1 Symbol Char. Transmit
SS
SS
Disable
Enable
0
1
Caps Lock Control
SS
SS
SS
“Caps Lock Off” State
“Caps Lock On” State
Auto Detect (PC/AT, PS/2, Keyboard Replacement and DOS/V Machines only)
0
1
2
Caps Lock Release Control
SS
SS
“Caps Lock On, Caps Off”
“Caps Lock On, Shift Off”
0
1
57
Configure Your FuzzyScan
Wireless FuzzyScan
Reference Manual
FNC1 Symbol Char. Transmit: When this function is enabled and the FNC1 is contained in scanned data, the scanner transmits the FNC1 to the host. Chart of theFNC1
is provided in Appendix- Keyboard Function Code Table. When the scanner interface is set to keyboard, the scan code is converted to corresponding key function before it
is transmitted.
The function of “Caps Lock Control” and “Key Pad Emulation” are only available for IBM PC/AT, PS/VP, PS/2 series personal computers and compatible machines.
While selecting the other host interfaces, these selections don’t perform the above functions for you.
Please check the actual Caps Lock state in use while software application is running. If the Caps Lock state is off, select “Caps Lock Off” state, then FuzzyScan will
perform normal data transmission. If the Caps Lock state is on, select “Caps Lock On” state. Select “Auto Detect”, FuzzyScan will perform special transmission
handshaking without changing the status of Caps Lock switch.
58
Configure Your FuzzyScan
Keyboard Interface Control
♦ Delay Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Intermessage Delay
SS
MS
Parameter Selection
Option Code
FIN
(2 digits)
None
1-99 (x10) msec.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intercharacter Delay
SS
MS
FIN
(2 digits)
None
1-99 (x5) msec.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Interfunction Delay
SS
MS
FIN
(2 digits)
None
1-99 (x5) msec.
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intermessage Delay is a time delay between messages output by FuzzyScan. Increasing this delay will help host applications process the incoming data on time.
Intercharacter Delay is a time delay between data characters output by FuzzyScan. This parameter is used to synchronize data communication when : 1) the data
transmission speed is too fast, characters may be skipped; 2) multitasking operation system or host computers in a network may slow down the keyboard handling; 3)
various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting this parameter
Interfunction Delay is a time delay between the transmissions of each segment of the message string.
Intermessage Delay, Intercharacter Delay and Interfunction Delay are unconfigurable under SPP and HID modes.
59
Configure Your FuzzyScan
Keyboard Interface Control
♦ Emulation Setting, Key Pad Emulation &
Upper/Lower Case Setting ♦
PROGRAM
Family Code Selection
P.C
Function Key Emulation
SS
SS
Parameter Selection
Enable ASCII 00-31 code as keyboard function code output
Ctrl-Output
F_DEFAULT
Option Code
0
1
Wireless FuzzyScan
Reference Manual
Refer to Appendix – Keyboard Function Code Table for details.
Key Pad Emulation
SS
SS
Disable key pad emulation
Enable numeric output as key pad (Num Lock On) output
0
1
Upper/Lower Case
SS
SS
SS
SS
Normal case (neglect the upper/lower case control)
Inverse case (change all characters output to inverse case)
Upper case (force all characters output as upper case)
Lower case (force all characters output as lower case)
0
1
2
3
60
Configure Your FuzzyScan
Serial Interface Control
♦ Record Suffix, Preamble ,Postamble Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
STX/ETX Control
SS
SS
Parameter Selection
Option Code
0
1
Disable STX/ETX transmission
Enable STX/ETX transmission
STX/ETX are two characters used to indicate the starting and ending of the total
data frame transmitted via serial interface.
Record Suffix
SS
SS
SS
SS
SS
SS
MS
None
CR (0DH)
LF (0AH)
CRLF (0D0AH)
TAB (09H)
SPACE (20H)
User defined character (1 character)
Preamble
SS
MS
None
1-15 characters
0
1
2
3
4
5
6, (00-7F)
FIN
[00-7F], [FIN]
Wireless FuzzyScan
Reference Manual
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
None
1-15 characters
FIN
[00-7F], [FIN]
Maximum 15-character input; scan “FIN” to terminate this selection.
FNC1 Symbol Char. Transmit
SS
SS
Disable
Enable
0
1
When this function is enabled and the FNC1 is contained in scanned data, the
scanner transmits the FNC1 to the host. Chart of the FNC1 is provided in Appendix –
Keyboard Function Code Table. When the scanner interface is set to keyboard, the
scan code is converted to corresponding key function before it is transmitted
Serial Interface Message String (RS232, USB COM) :
STX
Preamble
Data Length
Prefix Symbol ID
Scanned Data
Suffix Symbol ID
Postamble
ETX
Record Suffix
1 character
1-15 characters
2-4 digits
1 or 3 characters
Variable length
1 or 3 characters
1-15 characters
1 character
1 character
61
Configure Your FuzzyScan
Serial Interface Control
♦ Delay Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Intermessage Delay
SS
MS
Parameter Selection
Option Code
FIN
(2 digits)
None
1-99 (x10) msec.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intercharacter Delay
SS
MS
FIN
(2 digits)
None
1-99 (x5) msec.
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Interfunction Delay
SS
MS
FIN
(2 digits)
None
1-99 (x5) msec.
Wireless FuzzyScan
Reference Manual
Scan 2 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
Intermessage Delay is a time delay between messages output by FuzzyScan. Increasing this delay will help host applications process the incoming data on time.
Intercharacter Delay is a time delay between data characters output by FuzzyScan. These two parameters are used to synchronize data communication when : 1) the data
transmission speed is too fast, characters may be skipped; 2) multitasking operation system or host computers in a network may slow down the keyboard handling; 3)
various notebook or desktop PC systems require different timing parameter settings. Please always add one extra unit as safety margin when adjusting these two
parameters.
Interfunction Delay is a time delay between the transmissions of each segment of the message string.
Intermessage Delay, Intercharacter Delay and Interfunction Delay are unconfigurable under SPP and HID modes.
62
Configure Your FuzzyScan
Serial Interface Control
♦ Protocol, ACK/NAK Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Handshaking Protocol
SS
SS
SS
SS
None (free running mode)
RTS/CTS (hardware handshaking)
ACK/NAK (software handshaking)
Xon/Xoff (software handshaking)
NAK Retry Count
SS
SS
3 times
0~255 times
ACK Indication
SS
SS
SS
SS
Disable ACK Time-out Indication
Enable ACK Time-out Indication
Disable ACK Indication
Enable ACK Indication
Option Code
0
1
2
3
FIN
(3 digits)
0
1
2
3
USB COM doesn’t support RTS/CTS handshaking protocol.
When the ACK/NAK Software Handshaking option is selected, the FuzzyScan waits for an ACK (acknowledge) or NAK (not acknowledge) from the host computer after
each data transmission. If the NAK is received, FuzzyScan will re-send the data until receiving ACK.
ACK/NAK handshaking protocol is workable under following conditions:
1) Pair mode by using RS232 or USB COM interface.
2) SPP master or slave mode.
NAK Retry Count
After transmitting data, the scanner expects a NAK response from the host up to the preset “Serial Response Time-out”. If the scanner doesn’t get a response, the scanner
will issue an error indication and discard the data. When a NAK is received, the scanner transmits the same data again and waits for either an ACK or NAK. The scanner
issues an error indication and discards the data under following two conditions:
1) After preset NAK retry counts is received within the preset serial response time-out.
2) If the preset time-out is up but the preset NAK retry counts haven’t come to the end.
The default retry counts are three times. If you program “0 time”, the scanner won’t resend the data to the host when the scanner receives a NAK. The scanner will discard
the data. If you program “255 times”, the scanner can receive unlimited NAKs from the host within the pre-set serial response time-out.
This function is not available for batch mode. When you enable this function in on-line mode, the out-of-range function will be disable automatically.
ACK Indication:
Disable: There’s neither LED nor beeping indication for this setting.
Enable: There’s a specific LED and beeping indication for this setting.
63
Configure Your FuzzyScan
Serial Interface Control
♦Time Out Setting, Baud Rate, Data Frame ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Serial Response Time-out
SS
SS
SS
SS
SS
SS
None
200 mseconds
500 mseconds
800 mseconds
1 second
2 seconds
3 seconds
4 seconds
5 seconds
8 seconds
10 seconds
15 seconds
0
1
2
3
4
5
6
7
8
9
A
B
Baud Rate (BPS)
SS
SS
SS
SS
38.4K BPS
19.2K BPS
9600 BPS
4800 BPS
2400 BPS
1200 BPS
57.6K BPS
115.2K BPS
0
1
2
3
4
5
8
9
Data Frame
SS
SS
SS
SS
SS
SS
SS
SS
8, None, 1
8, Odd, 1
8, Even, 1
8, Space, 1
8, Mark, 1
8, None, 2
7, Odd, 1
7, Even, 1
7, Space, 1
7, Mark, 1
7, None, 2
7, Odd, 2
7, Even, 2
7, Space, 2
7, Mark, 2
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
When the RTS/CTS Hardware Handshaking option is selected, the RTS (request to send) and CTS (clear to send) signals will be issued before normal data
communication. This option is very helpful to ensure the reliability of data communication.
The Serial Response Time-out is a pre-defined delay time for FuzzyScan to wait for handshaking, acknowledgment or non-acknowledgment from the host
computer.
64
Configure Your FuzzyScan
Wand/Laser Emulation Control
(F, L, PF & PL)
[
PROGRAM
Family Code Selection
Output Polarity
♦ Output Polarity, Signal State, Margin/Module Time ♦
P.C
SS
SS
Parameter Selection
High level (5Vdc) on Bar (low level on Space)
Low level (0Vdc) on Bar (high level on Space)
F_DEFAULT
Option Code
0
1
Determine the output voltage level for both bar and space.
Initial Signal State
SS
SS
High Level (5Vdc)
Low Level (0Vdc)
0
1
Wireless FuzzyScan
Reference Manual
Determine the initial state of output voltage level.
Margin Time
SS
SS
SS
SS
SS
10 msec.
15 msec.
20 msec.
25 msec.
30 msec.
0
1
2
3
4
Module Time
SS
SS
SS
SS
Extremely short
Short
Medium
Long
0
1
2
3
Narrow/Wide Ratio
SS
SS
SS
1:2
1:2.5
1:3
0
1
2
65
Configure Your FuzzyScan
Wand/Laser Emulation Control
(F, L, PF, PL & PA Series)
PROGRAM
Family Code Selection
♦ Output Polarity, Signal State, Margin/Module Time ♦
P.C
Parameter Selection
F_DEFAULT
Option Code
0
Disable standard Code 39 emulation
SS
1
Enable standard Code 39 skip emulation
SS
2
Enable standard Code 39 replace emulation
SS
3
Enable Full ASCII Code 39 emulation
SS
4
Enable Code 128 emulation
SS
[ Code 39 Skip] : When this option is selected, all scanned data will be translated as Standard Code 39 wand/laser emulation output. If any lower case characters are read,
they will be translated to upper case characters. Any other characters that are not available in Code 39 symbology set will be skipped.
[ Code 39 Replace] : Any character not normally available in the standard Code 39 symbology set, will be translated as Space.
Wireless FuzzyScan
Reference Manual
Code 39/Code 128 Emulation
66
Configure Your FuzzyScan
Operation Control
♦ Operation Mode ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Operation Mode
SS
SS
Parameter Selection
Trigger mode
Presentation mode
Option Code
1
2
Wireless FuzzyScan
Reference Manual
Trigger Mode (Low Power Triggering) the scanner goes into standby state after scanning the bar code. You must press the trigger to turn on the light source of the
scanner before scanning the bar code.
Presentation Mode (Auto Detection) Presentation mode uses ambient light to detect the bar codes. The light source is off until the scanner detects an image which is
similar to a barcode. Then the light source turns on automatically to read the bar code. If the light level in the room is not high enough, Presentation Mode may not work
properly. You can choose different level of “Presentation Sensitivity” to meet your application (Please refer to the setting of “Presentation Sensitivity”).
PF / PL/ PA series do not support “Presentation Mode”.
67
Configure Your FuzzyScan
Operation Control
(A Series & PA Series)
♦ Batch Reading ♦
PROGRAM
Family Code Selection
P.C
Batch Reading
SS
Parameter Selection
None
Batch Reading rule input ( 01-16 rules)
F_DEFAULT
Option Code
[FIN]
[Rules] [FIN]
Batch Reading: When this function is enabled, you can scan multiple barcodes one by one continuously upon one trigger event. The scanner reports a good read beep and
indication only if all bar codes set by the “Batch Reading Rule” are read. Otherwise, the scanner reports an error beep and indication. The scanned data will be transmitted
according to the preset sequence which is defined in “Batch Reading Rule” regardless the scanned order of those barcodes.
Batch Reading function is only available Trigger Mode.
Batch Reading is not available when Multiple Read Mode or Center Alignment is turned on.
Wireless FuzzyScan
Reference Manual
Batch Reading Rule:
-
To set the Batch Reading rule
1.Scan the PROGRAM symbol.
2.Scan the Batch Reading symbol (Family Code).
3.Use the Option Code to define the preset Batch Reading rule.
4.Scan the FIN symbol.
5.Scan the END symbol to save your Batch Reading rule.
Note: Scan the ABORT and END symbol to exit without saving any Batch Reading rule setting.
-
When you scan “None”, the preset Batch Reading Rule will be cancelled.
-
Batch Reading Rule Syntax:
[n] [Element 1] FF [Element 2] FF [Element 3] FF …[Element n] FF
Where n is the number of elements in the overall rule. The number of elements is up to 16.FF indicates the end of one element.
-
Element structure:
[Cino ID Hex value] [Code length] [Character match(es)]
Where:
[Cino ID Hex value]
Length: 2 byte
Please find Cino ID hex value from Symbology ID Table in appendix. Locate the Hex value for the symbology and scan the 2 digit hex values from the Option
Code.
Note: 99 is the universal number, indicating all symbologies.
68
Configure Your FuzzyScan
[Code length]
Length: 4 byte
Specify what length of data output will be acceptable for this symbology. When you calculate the length, you must consider the whole data string which includes the
programmed Preamble, Postamble, Scanned Data Length, Prefix/Suffix Symbol ID or AIM ID. Scan the four digit data length from the Option Code.
Note: 40 characters is entered as 0040; 9999 is a universal number, indicating all lengths.
[Character match]
Length: 2-8 byte
You can refer to HEX/ASCII Reference Table to find the Hex value that represents the character(s) you want to match. Use the Option Code to scan the
alphanumeric combination that represents the ASCII characters. You can match up to 4 characters which are counted from the start character of the whole Data
String.
Note: When setting the matched character(s), you must match the content of the whole Data String, including the programmed Preamble, Postamble, Scanned
Data Length, Prefix/Suffi Symbol ID OR AIM ID if you had defined. FF is the universal character, indicating all characters.
-
Batch Reading rule example
In this example, you are scanning Code 39, Code 128, and Code 93 bar codes, but you would like to output the data in following sequence:
Code 128 - Code 39 - Code 93
Wireless FuzzyScan
Reference Manual
B-CODE39
A-CODE128
C-CODE93
69
Configure Your FuzzyScan
You would set up the Batch Reading rule with the following command line:
[PROGRAM] [Batch Reading] [0301999941FF07999942FF09999943FF] [FIN] [END]
Wireless FuzzyScan
Reference Manual
The breakdown of the command line is shown below:
03
The number of elements in the overall rule
01
Code identifier of Code 128
9999
Code length that must match for Code 128, 9999 = all lengths
41
Start character match for Code 128, 41h = “A”
FF
End of first code
07
Code identifier of Code 39
9999
Code length that must match for Code 39, 9999 = all lengths
42
Start character that must match for Code 39, 42h = “B”
FF
End of second code
09
Code identifier of Code 93
9999
Code length that must match for Code 93, 9999 = all lengths
43
Start character match for Code 93, 43h = “C”
FF
End of third code
To program the previous example using specific lengths, you would have to count the programmed Preamble, Postamble, Scanned Data Length, Prefix/Suffix
Symbol ID OR AIM ID if you had defined as part of the length. If you enable the Suffix Symbol ID of symbology, you would add one character to the previous
example’s length.
You would set up the Batch Reading rule with the following command line:
[PROGRAM] [Batch Reading] [0301001041FF070009FF09000943FF] [FIN] [END]
70
Configure Your FuzzyScan
The breakdown of the command line is shown below:
03
The number of elements in the overall rule
01
Code identifier of Code 128
0010
Code length that must match for Code 128
A-CODE128 sample length (9) plus Suffix Symbol ID (1) = 10
41
Start character match for Code 128, 41h = “A”
FF
End of first code
07
Code identifier of Code 39
0009
Code length that must match for Code 39
B-CODE39 sample length (8) plus Suffix Symbol ID (1) = 9
Universal matched character, indicating all character
FF
Also indicate end of second code
09
Code identifier of Code 93
0009
Code length that must match for Code 93
Wireless FuzzyScan
Reference Manual
C-CODE93 sample length (8) plus Suffix Symbol ID (1) = 9
43
Start character match for Code 93, 43h = “C”
FF
End of third code
Note: If the [Character match(es)] is set to “FF”, the following “FF” which indicated the end of the code was not need to set.
-
Structure of Data String
STX
Preamble
(RS232/USB COM
interface)
1 character
Scanned Data
Length
Prefix Symbol ID
Or
Scanned Data modified
by DataWizard
Prefix AIM Symbol ID
1-15 characters
2-4 digits
1 or 3 characters
Suffix Symbol ID
Postamble
Or
Suffix AIM Symbol ID
Variable length
71
1 or 3 characters
ETX
(RS232/USB COM
interface)
1-15 characters
1 character
Configure Your FuzzyScan
Operation Control
(All Series)
Wireless FuzzyScan
Reference Manual
PROGRAM
♦ Buzzer, Indicator, Vibrator, 1D Code Inverse Reading ♦
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Option Code
Buzzer Tone Adjust
SS
SS
SS
SS
SS
SS
SS
Buzzer tone – mute
Buzzer tone – low
Buzzer tone – medium
Buzzer tone – high
Buzzer tone - extremely high
Power-on beep
No power-on beep
0
1
2
3
4
5
6
Power On Indicator
SS
SS
SS
Disable (LED off)
LED steady on
LED flash
0
1
2
Good Read Indicator
SS
SS
Disable
Enable
0
1
Vibrator Control
SS
SS
Disable
Enable
0
1
Optional function, only available for vibrator model.
1D Barcode Inverse Reading
SS
SS
Disable
Enable
0
1
72
Configure Your FuzzyScan
Operation Control
(All Series)
♦ Beeping Control, Radio connection Beeps♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Beeping Control
SS
SS
SS
SS
Radio Connected/ Disconnected Beep On
Radio Connected/ Disconnected Beep Off
Battery Power Low Beep On
Battery Power Low Beep Off
0
1
2
3
Radio Connection Beeps
SS
Four ascending tone / Four descending tone
0
SS
Low-high two beeps / High-low two beeps
1
73
Option Code
Configure Your FuzzyScan
Operation Control
(A Series & PA Series)
♦ Buzzer Volume ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Family Code Selection
P.C
Buzzer Volume
SS
SS
SS
Parameter Selection
Low
Medium
High
F_DEFAULT
Option Code
0
1
2
74
Configure Your FuzzyScan
Operation Control
(A Series & PA Series)
♦ Timestamp Functions –
Set Date, Set Time, Timestamp Format Setting ♦
PROGRAM
Family Code Selection
P.C
Set Date
SS
Scan Date (MMDDYY)
6 digits + END
SS
For example, 2014-12-24, set 122414
Set Time (HHMM)
4 digits + END
Set Time
Parameter Selection
F_DEFAULT
Option Code
For example, for 24-hour clock Time Conversion, 14:56 set 1456
Wireless FuzzyScan
Reference Manual
Timestamp Format Setting
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
HH:MM DD/MM/YYYY
HH:MM MM/DD/YYYY
HH:MM YYYY/MM/DD
HH:MM:SS DD/MM/YYYY
HH:MM:SS MM/DD/YYYY
HH:MM:SS YYYY/MM/DD
DD/MM/YYYY HH:MM
MM/DD/YYYY HH:MM
YYYY/MM/DD HH:MM
DD/MM/YYYY HH:MM:SS
MM/DD/YYYY HH:MM:SS
YYYY/MM/DD HH:MM:SS
DD/MM/YYYY
MM/DD/YYYY
YYYY/MM/DD
HH:MM
HH:MM:SS
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
75
Configure Your FuzzyScan
Operation Control
(only PA Series)
Wireless FuzzyScan
Reference Manual
PROGRAM
♦ Timestamp Functions – Date & Time Format Setting,
Timestamp Output Control,
Stored Data Output Format, Online Mode Output Format♦
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Date & Time Format Setting
SS
SS
12 hour
24 hour
0
1
SS
SS
Short Year (YY)
Full Year (YYYY)
2
3
Timestamp Output Control
SS
SS
SS
SS
None
Batch mode
Online mode
Online mode & Batch mode
0
1
2
3
Stored Data Output Format
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
SS
Data/Record
Quantity + Data/Record
Data/Record + Quantity
Timestamp + Data/Record
Data/Record + Timestamp
Timestamp + Quantity + Data/Record
Timestamp + Data/Record + Quantity
Quantity + Timestamp + Data/Record
Quantity + Data/Record + Timestamp
Data/Record + Timestamp + Quantity
Data/Record + Quantity + Timestamp
0
1
2
3
4
5
6
7
8
9
10
Online Mode Output Format
(2D only)
SS
SS
SS
Data/Record
Timestamp + Data/Record
Data/Record + Timestamp
0
1
2
Timestamp Function is available for both Online Mode and Batch Mode.
76
Option Code
Configure Your FuzzyScan
Operation Control
( PF, PL &PA Series)
♦ Radio Link Mode for Discoverable Mode ♦
PROGRAM
Family Code Selection
P.C
Radio Link Mode for
Discoverable Mode
SS
SS
SS
SS
Parameter Selection
HID Mode
HID Mode with Passkey
HID Legacy Mode
SPP Slave Mode
Reference Manual
Option Code
0
1
2
3
You may also press FN1 of pocket scanner for more than 3 seconds to enter
discoverable mode.
Wireless FuzzyScan
F_DEFAULT
77
Configure Your FuzzyScan
Operation Control
(All Series)
♦ Dollar Sign Control, Redundancy, Control ♦
PROGRAM
Parameter Selection
Family Code Selection
P.C
Dollar Sign Control
SS
SS
SS
SS
SS
Dollar sign output as “ $ “
Dollar sign output as “￥“
Dollar sign output as “ € “
Dollar sign output as “ £ “
Dollar sign output as “ ¢ “
0
1
2
3
4
Redundancy
SS
SS
SS
SS
SS
SS
None
Level 1 Level 2
Level 3
Level 4
Level 5
To prevent potential miss reading.
0
1
2
3
4
5
Reference Manual
The Redundancy is the number of times the same bar code label has to be decoded before it is transmitted.
Wireless FuzzyScan
F_DEFAULT
78
Option Code
Configure Your FuzzyScan
Operation Control
(All Series)
♦ Delay Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
Reread Delay
(Double Scan Verification)
P.C
Option Code
SS
SS
SS
SS
SS
SS
Disable
Immediate time out
Short time out
Medium time out
Long time out
Force verification
0
1
2
3
4
5
Good Read Delay
SS
SS
SS
SS
SS
SS
SS
None
200 msec.
500 msec.
1 sec.
1.5 sec.
2 sec.
3 sec.
0
1
2
3
4
5
6
HID Mode Transmit Delay
SS
None
MS
1-250 msec.
FIN
(3 digits)
Scan 3 digits from the option code chart in Appendix, then FuzzyScan will terminate
this selection automatically.
The Reread Delay (Double Scan Verification) is designed to inhibit FuzzyScan from reading the same bar code label twice in pre-defined short duration. Force Verification
will not allow reading of the same bar code twice.
This Good Read Delay is the minimum amount of time before the scanner can read another bar code.
This HID Mode Transmit Delay will affect HID mode; When the scanner pairs with the Android, set this to 70ms to avoid data loss.
79
Configure Your FuzzyScan
Operation Control
(All Series)
♦ Time-out Setting, Good Read Duration ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Option Code
Light Source On Time
SS
SS
SS
SS
Short
Medium
Long
Extremely long
0
1
2
3
Hands Free Time-out
SS
SS
SS
SS
SS
Short
Medium
Long
Extremely long
Disable
0
1
2
3
4
Good Read Duration
SS
SS
SS
SS
SS
Short
Medium
Long
Extremely long
Extremely short
0
1
2
3
4
Time Delay to Low Power Standby Mode
SS
SS
SS
SS
SS
SS
1 sec
3 secs
5 secs
7 secs
9 secs
Immediate
0
1
2
3
4
5
Low Power Standby mode Link Indication
SS
SS
SS
Turn off immediately
Last for 1 minute
Keep on till power-off
0
1
2
The Light Source On Time is a pre-defined light source time out counter for Alternative Mode, Presentation Mode and Level Mode. The scanner keeps the light source on
till the pre-defined light source on time is up. You can adjust this parameter to meet your own application requirement.
The Presentation Mode is referred to as “hands free” mode. The hands free mode will be automatically changed to manual trigger mode when you press the trigger. You
can remain the scanner in manual trigger mode by setting the Hands Free Time-Out. Once the time-out duration is up (if there’s no any trigger operation), the imager will
revert to the original hands free mode.
The Time Delay to Low Power Standby Mode sets the time for scanner to enter low power trigger mode after any scanning activity.
80
Configure Your FuzzyScan
Operation Control
(All Series)
PROGRAM
♦ Presentation Scanning Setting, Laser Aiming Control ♦
Family Code Selection
P.C
Parameter Selection
Presentation Auto-sense
SS
SS
Disable
Enable
Presentation Sensitivity
SS
SS
SS
SS
SS
Level 1
Level 2
Level 3
Level 4
Level 5
F_DEFAULT
Option Code
0
1
Level 6
Level 7
0
1
2
3
4
5
6
Wireless FuzzyScan
Reference Manual
When enable the Presentation Auto-sense, the scanner can be switched between hands free scanning and hand-held scanning automatically when working with the
SmartStand or cradle.
The Presentation Sensitivity is used to configure the sensitivity level when the scanner is set as presentation mode. The higher lever means higher sensitivity for detecting
the barcode.
81
Configure Your FuzzyScan
Operation Control
(F, L, PF & PL Series)
♦ Scan Rate Control, ♦
PROGRAM
Family Code Selection
P.C
Scan Rate Control
SS
SS
Parameter Selection
Dynamic
Fixed
F_DEFAULT
Option Code
0
1
Wireless FuzzyScan
Reference Manual
Scan Rate Control: The scanner will have better motion tolerance when you select “Fixed” scan rate. It’s suitable for application which needs higher motion tolerance on
the move. But this may impact to the reading distance.
82
Configure Your FuzzyScan
Operation Control
(L & PL Series)
PROGRAM
♦ Smart stand Power Off Timeout, Laser Aiming Control,
LED Illumination Control ♦
Family Code Selection
P.C
SmartStand Power Off Timeout
SS
SS
SS
Parameter Selection
F_DEFAULT
Option Code
0
1
2
3 mins
5 mins
10 mins
Only available for FuzzyScan L series scanners.
SS
SS
Disable
Enable
0
LED Illumination Control
SS
SS
Always on
Intelligent Mode
0
1
LED Illumination Delay
SS
SS
SS
SS
SS
100 ms
150 ms
200 ms
250 ms
300 ms
0
1
2
3
4
Wireless FuzzyScan
Reference Manual
Laser Aiming Control
1
The SmartStand Power Off Timeout is a pre-defined duration for scanner’s light source on time when the scanner is placed on SmartStand. While the scanner is placed
on SmartStand, the scanner will be switched from hand-held scanning to presentation scanning and the light source will be forced on automatically. The light source will be
off when the pre-defined duration is up.
Laser Aiming Control: You can disable or enable laser aiming line when you scan PDF barcode.
LED Illumination Control: When you enable “always on“, the LED illumination will be always on when you press the trigger. When you enable “intelligent mode”, the
scanner will emit the laser aiming line first, the LED illumination will be turned on after the preset LED illumination delay. Intelligent mode is recommended to be used in
regular ambient light environment.
83
Configure Your FuzzyScan
Operation Control
(A Series & PA Series)
Wireless FuzzyScan
Reference Manual
PROGRAM
♦ Aiming Control, Delay Aiming & Decode Aiming Control ♦
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Illumination Control
SS
SS
Disable
Enable
0
1
Presentation Background Lighting
SS
SS
LEDs Off
LEDs On
0
1
Aiming Control
SS
SS
SS
Regular Aiming
Intelligent Aiming
Delay Aiming Control
0
1
2
Delay Aiming Time-out Control
SS
SS
SS
SS
200 ms
400 ms
800 ms
1 sec
Decode Aiming Control
SS
SS
SS
SS
Disable in Hand-Held mode
Enable in Hand-Held mode
Disable in Hand-Free mode
Enable in Hand-Free mode
1.5 secs.
2 secs.
3 secs.
4 secs.
Option Code
4
5
6
7
0
1
2
3
0
1
2
3
The Illumination Control is only available for hand-held mode.
Presentation Background Lighting Control: You can enable or disable presentation background lighting of the scanner according to the ambient light condition in
presentation mode. When the ambient light is dim or dark, you can enable this function to turn on the scanner’s LED illumination at a dim level. This is helpful for scanner to
detect the motion of scene.
The Aiming Control is only available for trigger mode. In Intelligent Aiming, the aiming light is turned on when the scanner is lifted. A trigger pull activates decoding process.
After 2 seconds of inactivity, the aiming light will be shut off. Delay Aiming Control allows a delay time for the operator to aim the scanner before the image is taken. During
the delay time, the aiming light will be on, but the LED illumination won’t be turned on until the delay time is up.
The Delay Aiming Time-out Control is only available for trigger mode. You can use Delay Aiming Time-out Control to set the delay time.
84
Configure Your FuzzyScan
Operation Control
(A Series & PA Series)
PROGRAM
♦ Center Alignment, Unique Bar Code Reporting ♦
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Option Code
Center Alignment
SS
SS
SS
SS
Disable in Hand-Held Mode
Enable in Hand-Held Mode
Disable in Hand-Free Mode
Enable in Hand-free Mode
0
1
2
3
Unique Bar Code Reporting
SS
SS
Disable
Enable
0
1
Wireless FuzzyScan
Reference Manual
Center Alignment: When this function is enabled, the scanner only decodes barcode(s) around aiming line.
Unique Bar Code Reporting: When this function is enabled, the scanner only outputs unique barcode when the trigger is pressed. This function is workable when Multiple
Read mode is selected.
85
Configure Your FuzzyScan
Operation Control
(All Series)
PROGRAM
♦ Out-of-range Scanning, Link Supervision Time-out ♦
Family Code Selection
P.C
Out-of-range Scanning
SS
SS
Parameter Selection
Disable
Enable
F_DEFAULT
Option Code
0
1
Out-of-range Scanning - When radio link is built between the scanner and remote host device, the scanner will transmit each scanned data right after scanning the
barcode data. However, the scanner is preset for unable to scan any barcode data when it loses the radio connection. You can enable the Out-of-range Scanning function
to continue scanning barcode data into memory buffer until radio link resumed.
Wireless FuzzyScan
Reference Manual
.
86
Configure Your FuzzyScan
Operation Control
(All Series)
PROGRAM
♦Radio-off Time-out Control, Power Off Time-out Control ♦
Family Code Selection
P.C
Radio-off Time-out
SS
MS
- Connect State
Parameter Selection
F_DEFAULT
Option Code
FIN
(2 digits)
12 (x5) minutes
0-99 (x5) minutes
If you don’t want the scanner to enter power-off, please set time-out to “0”
Radio-off Time-out
- Disconnect State
SS
MS
5 (x1) minute
0-99 (x1) minutes
FIN
(2 digits)
If you don’t want the scanner to enter power-off, please set time-out to “0”
Wireless FuzzyScan
Reference Manual
Power Off Time-out
SS
MS
1 (x5) minutes
0-99 (x5) minutes
FIN
(2 digits)
If you want the scanner to enter power off mode immediately, please set time-out to
“0”
The Radio-off Time-out Control can be set under radio connection or disconnection state. If the scanner is not used within the preset time-out duration, it will automatically
enter “Power Off ” for power saving purpose. You are able to disable this function by setting the time-out duration to “0”.
The Power Off Time-out: When the scanner is under radio-off, it is preset to enter Power Off automatically if the radio is not on after the time-out duration. If you would like
to power on the scanner, please press the trigger button. You can have the scanner enter this function immediately by setting the time-out duration to “0”
87
Configure Your FuzzyScan
Operation Control
(All Series)
♦ Batch Scanning Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Option Code
Batch Scanning Link Control
SS
SS
Radio disable
Radio enable
0
1
Stored Data Transmission
SS
SS
SS
All
On cradle
Scan barcode
0
1
2
Delete Stored Data after
Transmission
SS
SS
Disable
Enable
0
1
The Batch Scanning Link Control is a pre-defined radio option to control the radio-on or radio-off status under batch scanning operation. Please note that if the radio
disable is activated, the radio link will be disconnected once you enter batching scanning. The radio link will be resumed when you transmit the stored data or exit batch
scanning.
The Stored Data Transmission is a pre-defined approach when you want to transmit the scanned data under batch scanning operation. You can transmit the scanned data
by placing the scanner onto the cradle or scanning “Transmit Stored Data” command, or by either one of both methods.
In batching scanning, the default setting of Delete Stored Data after Transmission is disable. The scanner will keep all stored data after transmission until you scan the
“Clear All Stored Data” command. You are also able to delete all stored data after transmission automatically by enabling this function.
88
Configure Your FuzzyScan
Operation Control
(All Series)
♦ Batch Scanning Data Transmission Setting ♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Option Code
Field Delimiter
SS
SS
SS
SS
SS
SS
None
，
SPACE
–
．
User define
Stored Data Output Format
SS
SS
SS
As many times as the quantity indicates
<Quantity><Field Delimiter><Scanned Data>
<Scanned Data><Field Delimiter><Quantity>
0
1
2
Data Transmission Format
SS
SS
SS
Disable (scanned data only)
Leading with MAC address (MAC address and scanned data)
Leading with ID No. (scanner ID and scanned data)
0
1
2
0
1
2
3
4
5, [00-7F]
Only available for RS232, USB HID and USB COM interface in PAIR & PICO modes
The Field Delimiter is used to separate the specific information and scanned data into two fields. You can choose desired delimiter format.
The Stored Data Output Format If you want to input the quantity information of barcode data, you can enter the quantity from 1 to 9999 by scanning the quantity barcodes
right after you scanned the barcode data. The quantity information will be stored into the memory storage together with the barcode data. There are three ways to output the
stored barcode data and quantity information.
In PICO mode, up to 7 scanners can be connected with one smart cradle. The Data Transmission Format can help user to identify the source of the transmitted data.
You can choose to transmit the scanned data leading with MAC address or pre-assigned ID.
Example format: <MAC address><Field Delimiter><Data> or <ID><Field Delimiter><Data>.
I
89
Configure Your FuzzyScan
Operation Control
(All Series)
♦ Bluetooth Device Name & Security Setting♦
Wireless FuzzyScan
Reference Manual
PROGRAM
Parameter Selection
F_DEFAULT
Family Code Selection
P.C
Option Code
Bluetooth Device Name
SS
MS
Default device name
User define;
F/L series: 1-16 characters
A series: 1-32 characters
FIN
[00-7F], FIN
Bluetooth PIN Code
SS
MS
Default Bluetooth PIN Code
User define, 1-8 numbers
FIN
[30-39], FIN
Bluetooth Authentication
SS
SS
Disable
Enable
0
1
The default Bluetooth Device Name for F/L series is “F(L)xxxBT-xxxx”, and for PF/PL series is PF(L)xxxBT-xxxx, you will be able to change the device name by scanning
HEX values (1-16 characters).
The default Bluetooth Device Name for A series is “AxxxBT-xxxx”, you will be able to change the device name by scanning HEX values (1-32 characters).
The default Bluetooth PIN Code is “00000000”, you will be able to change the PIN Code by scanning HEX values (1-8 numbers).
The Bluetooth Authentication You can enable or disable the Bluetooth Authentication between the scanner and remote host device. If this function is enabled, when the
scanner wants to connect itself and sends the data to the host device, the host device has to return a link key shared between the scanner and the host device.
90
Configure Your FuzzyScan
Operation Control
♦ Bluetooth Other Settings ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Parameter Selection
Option Code
Bluetooth Sniff Control
SS
SS
Disable
Enable
0
1
Link Quality Control
SS
Disable
0
SS
Level 1
1
SS
Level 2
2
SS
Level 3
3
SS
Level 4
4
Wireless FuzzyScan
Reference Manual
The Bluetooth Sniff Control Bluetooth module will enter low power consumption mode when you enable this function.
Link Quality Control: This function is only available for SPP and HID mode. When you use the scanner in the boundary of radio signal, you can enable this function to
increase the reliability of data transmission. But this function will affect the communication distance. The level is higher, the communication distance is shorter.
91
Configure Your FuzzyScan
Operation Control
(All Series)
♦On-screen Keyboard Control ♦
PROGRAM
Family Code Selection
P.C
On-screen Keyboard Control
SS
SS
Parameter Selection
Disable
Enable
F_DEFAULT
Option Code
0
1
Wireless FuzzyScan
Reference Manual
When On-screen Keyboard Control is enabled, the scanner is preset to switch between barcode scanning and on-screen keyboard of most popular devices; you also can
have the scanner entered this setting by scanning “General Approach “ quick set command. Then you can turn off the radio to activate the on-screen keyboard by
scanning “Switch On-screen Keyboard” quick set command. If you use pocket scanner, you can activate the on-screen keyboard toggle by short pressing the FN1.
To work with iOS device, please change On-screen Keyboard Control to disable, or scan the “iOS Approach” quick set command to activate this function. Then you can
scan ““Switch On-screen Keyboard” quick set command to toggle the iOS on-screen keyboard. If you use pocket scanner, you can also activate the iOS on-screen
keyboard toggle by short pressing the FN1.
When you finished the keyboard input, please press the trigger once to turn on the radio, and the on-screen keyboard will be inactivated.
92
Configure Your FuzzyScan
Condensed DataWizard
♦ Preamble, Postamble, Data Length & Symbol ID Trans. ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Preamble
SS
MS
Parameter Selection
Option Code
FIN
[00-7F], [FIN]
None
1-15 characters
Maximum 15-character input; scan “FIN” to terminate this selection.
Postamble
SS
MS
FIN
[00-7F], [FIN]
None
1-15 characters
Maximum 15-character input; scan “FIN” to terminate this selection.
Data Length Transmission
SS
SS
Disable
Enable 2 digits data length transmission
0
1
If data length exceeds 99, 3-digit data length will be transmitted.
Wireless FuzzyScan
Reference Manual
Symbology ID Transmission
SS
SS
SS
SS
SS
SS
SS
Disable symbology ID transmission
Enable prefix symbology ID transmission
Enable suffix symbology ID transmission
Enable both prefix and suffix symbology ID transmission
Enable prefix AIM symbology ID transmission
Enable suffix AIM symbology ID transmission
Enable both prefix and suffix AIM symbology ID transmission
0
1
2
3
4
5
6
DataWizard is the most powerful, Artificial-Intelligence based data editing expert system provided specially for the FuzzyScan family bar code readers. Through DataWizard,
you can process the scanned data prior the transmissions in many ways as: Insert Delete, Match, Verify, Replace, Reorganize, and Repeat Transmission. It will help
you to arrange the transmission of scanned data to any specific format without software modification.
Due to the resources used by this system, Full-feature DataWizard is only supported by PowerTool. Through the PowerTool, all settings and configurations can be done
on-screen, under Windows 95/98/NT/2000/XP environment.
A Condensed Version DataWizard is provided by each FuzzyScan series. Through this menu, the condensed DataWizard can be utilized via bar code menu readings with
ease.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
If you have any problem to use DataWizard, please refer to following pages for details and consult your local FuzzyScan vendor or our web site for any assistance.
93
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Formatter Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Formatter Control
SS
MS
MS
1st Insertion
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
[1-3 characters], [FIN]
2-digits identified position; max. 3 insertion characters
2nd Insertion
SS
DS
FIN
(2 digits)
Disable
Enable
2-digits identified position; max. 3 insertion characters
Wireless FuzzyScan
Reference Manual
3rd Insertion
SS
DS
SS
DS
2-digits identified position; max. 3 insertion characters
[1-3 characters], [FIN]
position
FIN
(2 digits)
Disable
Enable
[1-3 characters], [FIN]
position
FIN
(2 digits)
Disable
Enable
2-digits identified position; max. 3 insertion characters
4th Insertion
position
[1-3 characters], [FIN]
position
The Data Formatter is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for formatter control, and provides Multiple Position Insertion and Multiple Character Insertion (max three characters) in the identified position.
While the Data Formatter is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbolology ID or Record
Suffix. All of the above programmable parameters perform the same function depending on your setting.
Regarding the “Bar Code Selection” and “Position Calculation” of data formatter, please refer to page 60 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
94
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Verifier Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Verifier Control
SS
MS
MS
Identified Data Length
SS
MS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
Determine the identified data length for verification.
1st Identified Character
SS
DS
FIN
(2 digits)
Disable
Enable
2-digits checking position; 1 identified character
Wireless FuzzyScan
Reference Manual
2nd Identified Character
SS
DS
2-digits checking position; 1 identified character
3rd Identified Character
SS
DS
position
FIN
(2 digits)
Disable
Enable
2-digits checking position; 1 identified character
[00-7F]
position
FIN
(2 digits)
Disable
Enable
[00-7F]
[00-7F]
position
The Data Verifier is used to provide advanced verification for error-free scanning and to work as an Embedded Data Transmitting Filter.
All data must conform to the Identified Bar Code Symbologies, Identified Data Length, and one to three Identified Characters in the checking position. Otherwise, the
FuzzyScan will not transmit the data to the host computers or terminals, but will instead issue 3 long beeps for verification error and skip the scanned data.
The Data Verifier checks only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Verifier, please refer to page 60 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
95
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Replacer Setting ♦
PROGRAM
F_DEFAULT
Family Code Selection
P.C
Replacer Control
SS
MS
MS
1st Replacement
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
[00-7F]
2-digits identified position; 1 replacement character
2nd Replacement
SS
DS
FIN
(2 digits)
Disable
Enable
2-digits identified position; 1 replacement character
Wireless FuzzyScan
Reference Manual
3rd Replacement
SS
DS
position
position
FIN
(2 digits)
Disable
Enable
2-digits identified position; 1 replacement character
[00-7F]
[00-7F]
position
The Data Replacer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for replacer control, and provides Multiple Position Replacement in the identified position.
All data must conform to the Identified Bar Code Symbologies, and one to three Identified Characters in the identified position while the Data Replacer is enabled, it
arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Replacer, please refer to page 60 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.
96
Configure Your FuzzyScan
Condensed DataWizard
♦ Data Organizer Setting ♦
PROGRAM
Family Code Selection
P.C
Organizer Control
SS
MS
MS
1st Organization
SS
DS
2nd Organization
Reference Manual
Include/Exclude Control
Wireless FuzzyScan
F_DEFAULT
SS
DS
SS
DS
Parameter Selection
Option Code
2nd Option Code
Disable
Select one bar code symbology
Select all bar code symbologies
FIN
(2 digits)
00
automatic termination
automatic termination
Disable
Enable
FIN
(2 digits)
2-digits identified position;
Forward/backward data transmission setting
position
direction
Disable
Enable
FIN
(2 digits)
2-digits identified position;
Forward/backward data transmission setting
position
direction
Transmitted data excluded the data of identified position
Transmitted data included the data of identified position
0 (Forward)
1 (Backward)
0 (Forward)
1 (Backward)
0
1
The Data Organizer is used to edit the scanned raw data prior to transmitting the data to the host computers or terminals. It allows you to select desired bar code
symbologies for organizer control, and provides maximum two identified positions to send the data forward or backward. It also allows you to control the transmitted data
including or excluding the data of identification position. Please refer to the application example listed in page 60 for details.
While the Data Organizer is enabled, it arranges only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record
Suffix.
Regarding the “Bar Code Selection” and “Position Calculation” of Data Organizer, please refer to page 60 for details.
Please note that all “Character” input should be referred to the ASCII/HEX Table.
97
Configure Your FuzzyScan
2D Bar Code Symbology
Select a Bar Code Symbology
You can select one or all types of bar code symbologies to
use Condensed DataWizard for advanced transmission
arrangement. If you scan “00” to select all types, the
FuzzyScan will arrange all incoming data to meet your
pre-defined format. If you want to select only one type bar
code, please select one of the option code listed below.
Wireless FuzzyScan
Reference Manual
1D Bar Code Symbology
QR Code
A0
MaxiCode
A2
MicroQR Code
A0
Aztec Code
A3
DataMatrix
A1
Chinese Sensible Code
A4
GS1 DataMatrix
A5
Postal Code
Korea Post Code
21
Japanese Post
B4
Australian Post
B0
KIX Post
B5
British Post
B1
Planet Code
B6
Intelligent Mail barcode
B3
Postnet
B8
Code 128
01
Matrix 2 of 5
38
GS1-128
31
Interleaved 2 of 5
48
UPC-A
02
China Postal Code
58
UPC-A with 2 supplement
32
German Postal Code
68
Position Calculation
UPC-A with 5 supplement
42
Standard/Industrial 2 of 5
08
[Data Formatter]
UPC-E
03
Code 93
09
UPC-E with 2 supplement
33
Code 11
10
UPC-E with 5 supplement
43
MSI/Plessey
11
EAN-13
04
UK/Plessey
12
EAN-13 with 2 supplement
34
Telepen
13
EAN-13 with 5 supplement
44
GS1 DataBar
14
EAN-8
05
IATA
15
EAN-8 with 2 supplement
35
Coupon Code
16
EAN-8 with 5 supplement
45
PDF417
17
Codabar/NW-7
06
Codablock F
18
Code 39
07
Code 16K
19
Code 32
37
Code 49
20
X
X
X
X
X
X
X
X
X
X
X
Trioptic Code 39
47
GS1 DataBar Limited
22
00
01
02
03
04
05
06
07
08
09
10
GS1 DataBar Expanded
23
Composite Codes
24
Micro PDF417
25
If there is a 5-character input data string, refer to the
following to calculate the actual position for insertion:
X
00
X
01
X
02
X
03
X
04
05
[Data Verifier, Data Replacer, Data Organizer]
If there is a 11-character data string, please refer to the
following to calculate the actual position for identification.
98
Configure Your FuzzyScan
Application Example
Programming Procedure
If your bar code label is a 16-digit Interleaved 2 of 5 which
includes the information of 6-digit date code, 6-digit serial
number and 4-digit unit price, you want the FuzzyScan do the
following for you without software modification:
[Data Verifier]
Apply only Interleaved 2 of 5 to the condensed
DataWizard.
Check bar code is actually with 16-digit length.
Allow bar code output whose date code is leading with “9”.
Three outputs with “TAB” suffix.
The date code output should skip “9” and replaced it by
“A”.
The serial number output should be led with “SN”.
Reference Manual
Scan “Verifier Control” and set bar code symbology to
“48” (Interleaved 2 of 5).
Scan “Identified Data Length” and set the length to
“16”.
Scan “1st Identified Character” and set the identified
position to “00”, then set the identified character to “39”
(Hex Code of 9).
[Data Formatter]
Scan “Formatter Control” and set bar code symbology
to “48”.
The unit price output should be skipped the first 2 digits.
Wireless FuzzyScan
Scan “Program” to enter the programming mode.
Scan 1st Insertion” and set the identified position to
“06”, then inserted characters to “09” (Hex Code of
TAB), “53” (Hex Code of S), “4E” (Hex Code of N).
Test Bar Code : 9 8 1 0 2 5 1 2 3 4 5 6 9 8 7 6
Actual Output : A81025[TAB]SN123456[TAB]76[TAB]
Scan “2nd Insertion” and set the identified position to
“12”, then inserted character to “09”. In the final, you
must scan “FIN” (Finish) code to terminate this
selection.
Scan “3rd Insertion” and set the identified position to
“16”, then inserted character to “09”. In the final, you
must scan “FIN” (Finish) code to terminate this
selection.
99
Configure Your FuzzyScan
[Data Replacer]
Scan “Replacer Control” and set bar code symbology to
“48”.
Scan “1st Replacement” and set the identified position to
“00”, then replaced character to “41” (Hex Code of A).
[Data Organizer]
Scan “Organizer Control” and set bar code symbology to
“48”.
Scan “1st Organization” and set the identified position to
“16”, then set the data transmission to “0” (forward).
Wireless FuzzyScan
Reference Manual
Scan “2nd Organization” and set the identified position to
“17”, then set the data transmission to “1” (backward).
Scan “END” (Exit) to terminate the programming.
[Important Notice]
Please note that Condensed DataWizard will follow the
preset working flow as below:
Verifier
Formatter Replacer
Organizer
So when you set the identified position in Data Organizer,
you must consider the inserted data which you already set
via Data Formatter.
100
Appendix
Symbology ID Table
Each AIM Code Identifier contains the three-character string ]cm where:
] = Flag Character, c = Code Character, m = Modifier Character
Cino ID
Code Family
Primary Format
Hex
value
UPC
UPC-A
2
UPC-A with 2 supple.
32
UPC-A with 5 supple.
42
UPC-E
3
UPC-E with 2 supple.
33
UPC-E with 5 supple.
43
AIM ID
Code
Code
Chara
Charact
cter
er
A
E
E
Cino ID
Modified
Code Family
Character
Wireless FuzzyScan
Reference Manual
Codabar
B
GS1-128
31
C
Codabar/NW-7
06
D
F
Standard/Industrial 2 of 5
08
I
S
Matrix 2 of 5
38
K
X
C
48
IATA
I
Chara
ter
cter
Modified
Character
1
EAN/JAN-8 with 2 supple.
35
2
EAN/JAN-8 with 5 supple.
45
2
EAN/JAN-13
04
0
EAN/JAN-13 with 2 supple.
34
EAN/JAN-13 with 5 supple.
44
0
EAN/JAN
4
N
F
E
E
1
1
2
Example: A EAN/JAN-8 bar code 49123562 with 5 supplement 12345 is
transmitted as ]E449123562]E212345
m
Code 93
Code 93
1
Code 11
Code 11
10
P
H
m
m
MSI/Plessey
MSI/Plessey
11
R
M
m
0
UK/Plessey
UK/Plessey
12
S
P
0
0
Telepen
T
B
m
X
e
m
m
GS1 DataBar
China Postal Code
58
L
X
0
German Postal Code
68
M
I
m
IATA
15
O
R
m
Z
Example : A UPC-A 512345678900 + GS1-128 81010123451297 bar
code is transmitted as]E0512345678900]C181010123451297
Example: A EAN-13 9923456789019 + GS1-128 81010123451297 bar
code is transmitted as ]E09923456789019]C181010123451297
Compsoite
Code 39
PDF417
09
Telepen
13
GS1 Databar
14
GS1 DataBar Limited
22
GS1 DataBar Expanded
UCC Coupon Code
UCC Coupon
J
Charac
05
Interleaved 2 of 5
Code 25
Code
EAN/JAN-8
2
01
Charact
Code
0
1
Code 128
Code
er
Example: A UPC-A bar code 012345678950 with 2 supplement 12 is
transmitted as ]E0012345678950]E112
Code 128
Primary Format
AIM ID
Composite Code
23
H
G
m
24
Code 39
07
G
A
m
Code 39 Trioptic
47
W
X
0
Code 32
37
G
A
0
V
L
m
PDF417
17
Micro PDF417
25
Codablock
Codablock F
18
Y
O
m
Korea Post
Korea Post Code
21
a
X
0
Remark: Above examples are given for the transmission of AIM ID.
101
Appendix
2D Symbology ID Table
Cino ID
Code Family
Primary Format
Hex
Value
QR Code
Micro QR
Code
Reference Manual
Cino ID
Modified
Char.
Char.
b
Q
m
c
d
m
Japanese
Post
QR Code
Micro QR Code
A0
Code Family
Code
Char.
Primary Format
Hex
AIM ID
Char.
Value
British Post
British Post
Intelligent
Mail barcode
Intelligent Mail barcode
Code
Modified
Char.
Char.
B1
h
0
B3
j
0
Japanese Post
B4
k
Data Matrix
A1
GS1 Data Matrix
A5
MaxiCode
MaxiCode
A2
d
U
m
KIX Post
KIX Post
B5
l
0
Aztec Code
Aztec Code
A3
e
z
m
Planet Code
Planet Code
B6
m
0
Chinese
Sensible
Chinese Sensible
A4
f
0
Postnet
Postnet
B8
o
0
Australian
Post
Australian Post
Data Matrix
Wireless FuzzyScan
AIM ID
X
B0
g
0
102
X
0
Appendix
Wireless FuzzyScan
Reference Manual
Keyboard Function Code Table
No.
ANSI
ASCII
00
NUL
00H
01
SOH
02
Key Function
No.
ANSI
ASCII
Key Function
RESERVED
16
DLE
10H
F7
01H
CTRL (Left)
17
DC1
11H
F8
STX
02H
ALT (Left)
18
DC2
12H
F9
03
ETX
03H
SHIFT
19
DC3
13H
F10
04
EOT
04H
CAPS LOCK
20
DC4
14H
F11
05
ENQ
05H
NUM LOCK
21
NAK
15H
F12
06
ACK
06H
ESC
22
SYN
16H
INS (Insert) (Edit)
07
BEL
07H
F1
23
ETB
17H
DEL (Delete) (Edit)
08
BS
08H
BACK SPACE
24
CAN
18H
HOME (Edit)
09
HT
09H
TAB
25
EM
19H
END (Edit)
10
LF
0AH
F2
26
SUB
1AH
PAGE UP (Edit)
11
VT
0BH
F3
27
ESC
1BH
PAGE DOWN (Edit)
12
FF
0CH
F4
28
FS
1CH
UP (Edit)
13
CR
0DH
ENTER (CR)
29
GS
1DH
DOWN (Edit)
14
SO
0EH
F5
30
RS
1EH
LEFT (Edit)
15
SI
0FH
F6
31
US
1FH
RIGHT (Edit)
To emulate the keyboard function key input for user definable parameters, user must configure actual content using the
Reserved ASCII 0 – 31 characters, and also Enable the “Function Key Emulation”. Otherwise, the Ctrl output will be done
by the scanner. Please refer to the above Keyboard Function Code Table which is for IBM PC/XT/AT, PS/2, PS/VP,
COMPAQ PC, HP Vectra PC, Notebook PC, APPLE and PowerMac, and WYSE PC Enhanced or fully compatible machines.
The last character in the Ctrl Output column is varied for different countries.
Country (refer to Keyboard Layout) & Character
United State
Switzerland
Belgium
UK
Sweden
Denmark
Spain
Italy
-
France
Germany
Norway
103
=
-
Appendix
ASCII Input Shortcut
L
0
NUL
DLE
SPACE
0
@
P
`
p
1
SOH
DC1
!
1
A
Q
a
q
2
STX
DC2
"
2
B
R
b
r
3
ETX
DC3
#
3
C
S
c
s
4
EOT
DC4
$
4
D
T
d
t
Example:
5
ENQ
NAK
%
5
E
U
e
u
If you want the scanned data output leading with a Dollar
Sign, you have to set the “Preamble” to “$”. The configuration
procedure is listed below for reference.
6
ACK
SYN
&
6
F
V
f
v
7
BEL
ETB
'
7
G
W
g
w
8
BS
CAN
(
8
H
X
h
x
Scan the system command – PROGRAM listed on page
3-24 to enter programming mode.
9
HT
EM
)
9
I
Y
i
y
A
LF
SUB
*
:
J
Z
j
z
B
VT
ESC
+
;
K
[
k
{
C
FF
FS
,
<
L
\
l
|
Refer to the Hex/ASCII Table, you will find the HEX value
of “$” is 24.
D
CR
GS
-
=
M
]
m
}
E
SO
RS
.
>
N
^
n
~
Scan the option code – 2 listed on the fold out back cover.
F
SI
US
/
?
O
_
o
DEL
Scan the option code – 4 listed on the fold out back cover.
Example : ASCII “A” → HEX “41”; ASCII “a” → “61”
To configure the user definable parameters of FuzzyScan via
programming menu, FuzzyScan will ask you to scan your
desired ASCII value in HEX form. You have to refer to the
“HEX/ASCII Table” for details.
Wireless FuzzyScan
Reference Manual
Scan family code – PREAMBLE to select this family.
Scan the system command – FIN (Finish) to terminate
Preamble setting.
Scan the system command – End to exit the programming
mode for normal operation.
HEX/ASCII Reference Table
H
0
1
2
3
4
5
6
7
104
: High Byte of HEX Value
: Low Byte of HEX Value
Appendix
Link Mode Quick Set
PAIR Mode
PICO Mode
Uninstall
SPP Master Mode
SPP Slave Mode
HID Mode
Wireless FuzzyScan
Reference Manual
HID Legacy Mode
HID Mode with Passkey
105
Appendix
Host Interface Quick Set
(Work with Smart Cradle only)
USB HID Standard Mode
PS/2 (DOS/V) KBW Standard Mode
RS232 Serial
USB HID Turbo Mode
PS/2 (DOS/V) KBW Turbo Mode
USB Com Port Emulation
Wireless FuzzyScan
Reference Manual
USB HID Legacy Mode
PS/2 (DOS/V) Keyboard Replacement
106
Appendix
Option Codes
0
8
4
C
1
9
5
D
2
A
6
E
Wireless FuzzyScan
Reference Manual
3
B
7
FIN (Finish)
F
Abort
107
END (Exit)
Appendix
Toggle between Barcode scanning and On-screen keyboard of mobile devices
General Approach ◆
Switch On-screen Keyboard
iOS Approach
Available for FuzzyScan Bluetooth Cordless Scanner:
One of following Bluetooth scanners with proper firmware preload:
Bluetooth Image Scanners
F680BT / F780BT :
Rev. 4.00.05 and above
L680BT / L780BT:
Rev. 4.00.05 and above
A770BT :
Rev. 1.00.14 and above
Wireless FuzzyScan
Reference Manual
Rev. 2.00.02 and above
Bluetooth Pocket Scanners:
PF680BT / PL680BT : Rev. 1.00.05 and above
PA670BT :
Rev. 1.00.01 and above
Please refer to P.18 “Simultaneous Barcode Scanning and On-screen Keyboard” for more details.
108
Appendix
System Commands
Save Configuration
PROGRAM
(Enter Programming Mode)
Paging
FIN (Finish)
Clone
PowerTool Host Link
END
(Exit Programming Mode)
Factory Default
Power Off
Wireless FuzzyScan
Reference Manual
System Information List
(SYSLIST)
Master Default
Factory Default: After scanning” Factory Default” command, all parameters will be returned to factory default value (The radio link will be disconnected and the
scanner will revert to uninstall state).
Master Default: After scanning “Master Default” command, the scanner will remain the pre-set parameters of Host Interface Selection, Keyboard Interface
Control (except Record Suffix; Preamble; Postamble), Serial Interface Control (except Record Suffix; Preamble; Postamble), Wand/Laser Emulation Control,
Bluetooth Device Name, Bluetooth PIN Code, and Out-of-range Scanning, the rest of parameters will be returned to default value (The radio link is still keep
on).
Save User Default
User Default
User Default: After scanning” Save User Default” command, all current parameters will be stored to the flash memory. Once you change the parameter and
would like to return to previous setting, please scan “User Default”.
109
Appendix
Indications
Wireless FuzzyScan
Reference Manual
Scanner Indication
Items
Radio connection
Link Indicator
1 blue blink per 2.5 sec.
Beeping
Off
Radio disconnection
3 blue blinks per 2 sec.
Off
During connection
Quick blue blinks
Short clicks
Radio connection built
1 blue blink per 2.5 sec.
4 beeps in ascending tone
Radio connection lost
3 blue blinks per 2 sec.
4 beeps in descending tone
Data Transmission
Quick blue blink
Short clicks
Items
Under charging (on cradle)
Status Indicator
Steady red
Off
Fully charged (on cradle)
Steady green
Off
Under batch scanning
1 green blink per 2.5 sec.
Off
Pair failure
Steady red
2 Di-do Di-do beeps
Out of memory
2 red blinks
2 long beeps
Battery power low
1 red blink at regular interval
1 beep at regular interval
Battery power extremely low
8 red blinks
8 beeps
Good read
1 green blink
1 good read beep
Under Configuration
Steady red
Off
Uninstall state
Alternative red and green blinks
Off
Upgrade state
Steady red
Short click
Time out warning
Off
3 long beeps
Paged by smart cradle
Off
6 page beeps
Battery no power
Off
Off
Power Off
Off
Off
Beeping
110
Appendix
Central Indicator
Central Indicator
Side Indicators
Side Indicators
HB211x / HB3112 Smart Cradle Indications
Items
Power on
Off
Power on beeps
Smart Cradle Upgrade State
Off
Steady red
Short clicks
Uninstall state
Off
Alternative red-green blinks Off
Steady blue
Steady Green
Off
Radio Disconnected Off
Steady red
Off
Radio Connected
Off
Off
Radio Disconnected Off
Steady red
Off
PICO Mode
Steady blue
Steady green
6 page beeps
PAIR Mode
Steady blue
Off
6 page beeps
PAIR Mode
Reference Manual
Beeping
Central
blue blink once
PICO Mode
Wireless FuzzyScan
Indicators
Smart cradle paged
by scanner
Radio Connected
Steady blue
Side
HB2100 Charging Cradle Indication
Items
Power on
Central Indicator
Light blue
Beeping
Off
111
FuzzyScan Wireless Reference Manual
CINO GROUP
PC WORTH INT’L CO., LTD. www.cino.com.tw
">