Assembly Instructions – Plymouth Fire Table

Add to my manuals
12 Pages

advertisement

Assembly Instructions – Plymouth Fire Table | Manualzz

PLYMOUTH FIRE TABLE

ASSEMBLY INSTRUCTIONS

.

.

CSA Model 98910L

Printed in China

Installer: Leave these instructions with consumer.

Consumer: Keep these instructions for future reference.

DANGER  

If you smell gas:

1.

Shut off gas to the appliance.

2.

Extinguish any open flame.

3.

If odor continues, keep away from the appliance and immediately call your gas supplier or fire department.

WARNING: Improper installation,  adjustment alteration, service or  maintenance can cause injury or property  damage. Read the installation, operating  and maintenance instructions thoroughly  before installing or servicing this equipment. 

WARNING: For Outdoor Use Only

WARNING

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

T

shall not be stored in the vicinity of this or any other appliance.

FOR USE WITH 20LB. PROPANE

CYLINDER (NOT SUPPLIED) WITH

TYPE 1 CONNECTION OR FOR USE

WITH NATURAL GAS AFTER

CONVERSION KIT IS INSTALLED

DANGER CARBON MONOXIDE HAZARD

This appliance can produce carbon monoxide which has no odor.

Using it in an enclosed space can kill you.

Never use this appliance in an enclosed space such as a camper, tent, car or home.

Questions, Problems, Missing Parts? Before returning to your retailer, call our customer service department in the

US and Canada at 1-800-325-2315, Monday-Friday, 8 a.m.–

5 p.m. Eastern Time.

WARNING: USE FACTORY

APPROVED REPLACEMENT

PARTS AND ACCESSORIES

ONLY.USE OF UNAPPROVED

PART OR ACCESSORIES CAN

VOID THE WARRANTY ON

THIS PRODUCT AND RESULT

IN A HAZARDOUS

CONDITION. PLEASE

CONTACT US FOR

INFORMATION REGARDING

REPLACEMNT HOSES,

THERMOCOUPLES,

ELECTRODES, IGNITION

MODULES, LAVAROCKS,

LOGS, ETC.

May 2014

TABLE OF CONTENTS

Important Safety Information 3

Information about Propane 4

Specifications 4

Installation 5

Natural Gas Conversion 8

Lighting Instructions 9

Maintenance 10

Batteries 10

Parts List 11

Warranty 12

2

IMPORTANT SAFETY INFORMATION

The installation must conform with local codes or, in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54; International Fuel Gas Code. ; Natural Gas and Propane

Installation Code, CSA B149.1; or Propane Storage and Handling Code, B149.2, as applicable.

The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in excess of 1/2 psi (3.5kPa).

The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve during any pressure testing of the gas supply system at test pressure equal to or less than 1/2 psi

(3.5kPa).

The appliance area must be kept clear and free from combustible materials, gasoline and other flammable vapors and liquids.

Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

Children and adults should be alerted to the hazards of high surface temperatures and kept at a safe distance to avoid burns or clothing ignition.

Young children should be carefully supervised when they are anywhere near the appliance.

Clothing or other flammable material should not be hung from the appliance, or placed on or near the appliance.

Any screen or guard removed for servicing an appliance must be replaced prior to operating the appliance.

Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a professional service person. More frequent cleaning may be required as necessary. It is imperative that the control compartments, burners and circulating air passageways of the appliance be kept clean.

Do NOT burn solid fuels in this gas fireplace.

CAUTION: The propane gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of 11 inches water column.

This outdoor gas appliance is not intended to be installed in or on recreational vehicles and/or boats.

Before each use of this gas appliance, open the LP (Liquid Propane) Tank Drawer and inspect the LP

Hose. If there is evidence of excessive abrasion or wear, or the hose is cut, it must be replaced prior to the gas appliance being put into operation. Use only the replacement hose assembly specified in this manual. Inspect the burner before each use of the appliance. The burner must be replaced prior to the appliance being put into operation if it is evident that the burner is damaged. Use only the burner listed in these instructions.

Keep the fuel supply hose away from any heated surfaces.

3

IMPORTANT SAFETY INFORMATION ABOUT

PROPANE (LP) GAS

A self contained LP-gas cylinder for use with this appliance must have a capacity of 20 lbs. and must be equipped with a Type 1 connector and an OPD (overfill protection device). See Figure 1.

The LP-gas supply cylinder to be used must be constructed and marked in accordance with the specification for LP-gas cylinders of the U.S. Department of Transportation (DOT) or the National

Standard of Canada, CAN/CSA-B339, Cylinder, Sphere and Tubes for the Transportation of Dangerous

Goods.

 The cylinder supply system must be arranged for vapor withdrawal.

 The cylinder used must include a collar to protect the cylinder valve.

 This appliance shall be used only outdoors in a well-ventilated space and shall not be used in a building, garage or any other enclosed space.

 When this appliance is not is use, the gas must be turned off at the supply cylinder.

 Storage of this appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance.

 Cylinders must be stored outdoors in a well-ventilated area out of the reach of children .Disconnected cylinders must have threaded valve plugs tightly installed and must not be

 stored in a building, garage or any other enclosed areas.

CSA (Canadian Standards Association) certified to ANSI Z21.97•CSA 2.41-2012 “ Outdoor

Decorative Gas Appliances” The gas hose is routed through a “U” bolt to prevent the hose from coming in contact with the burner. DO NOT remove the hose from the “U” bolt. See Figure 2.

SPECIFICATIONS

INPUT

Propane Regulator Pressure

Natural Gas Minimum Inlet

Pressure

40,000 Btu/hr

11 inches water column

7 inches water column

Clearances to combustible surfaces Sides 24in./61cm

30,000 Btu/hr Low fire

Top: 72 in. / 183 cm

INSTALLATION

4

1. With the help of another person, turn the table base assembly in the upright position. With the help of another person, carefully place the natural stone table top onto the table base. After making any necessary adjustments to the alignment of the natural stone table top and the top connector bracket, use bolts and washers as shown in Fig.3. Guide the bolt through the top connector bracket into the pre-drilled hole on the underside of the natural stone table top. Do not tighten completely. Repeat on other three holes of the top leg connector bracket. (Note: holes do not go through to the top of the table. Holes shown for illustration purposes only.)

Figure 3

2. Pour all of the lava rock into the burner pan. Completely cover the burner tube with lava rocks as shown in Fig. 4

Figure 4

3. The logs and burner are lettered. Place the logs as shown in Fig. 5 through 9.

5

Figure 5. Log A

Figure 6. Log B Figure 7. Log C

Figure 8. Log D Figure 9. Log E

4. Remove any lava rock from the ignition well as shown in Fig. 10.

Figure 10

Remove any lava rock from the ignition well

5. Lift off the tank door, place the tank in the holder and use the chain to hold the tank. Connect the regulator as shown in Fig. 11. Screw the black handle clock-wise to tighten. Turn the handle counterclock-wise to remove. The hose must point down. Open the control door and check that the valve is turned all the way clockwise to the “OFF” position. Open the tank valve. Apply a

6

solution of soapy water to the tank-regulator connection and to the valve-hose connection to check for leaks. If soap bubbles continue to form, the connection has a leak. If a leak is found, close the tank valve and tighten all connections. NEVER USE A FLAME TO CHECK FOR

LEAKS.

Figure 11

6. Tighten threaded knobs found on tank tray (Fig. 12) so that the LP tank cannot move from side to side. Do not remove plastic cap from end of threaded section.

Figure 12

7

NATURAL GAS CONVERSION

Natural gas conversion must be performed only by natural gas provider or service company.

1. Disconnect the gas hose from the gas valve. See Fig. 13.

Figure 13

2. Disconnect the gas tube from the orifice and remove the orifice holder as shown in Fig .14.

Figure 14

3. Replace the propane orifice (See Figure 15) with the natural gas orifice from the kit and reinstall the orifice holder by tightening the nuts as shown in Fig. 16. Reconnect and tighten the gas tube to the orifice.

Figure 15 Figure 16

Apply a solution of soapy water to all connections to check for leaks. If soap bubbles continue to form, the connection has a leak. If a leak is found, close the tank valve and tighten all connections.

NEVER USE A FLAME TO CHECK FOR LEAKS.

8

4.

Stick the conversion label on the rating plate as shown in Fig. 17.

Metal Rating Plate

Serial Number _________________

5.

Model Number: 98910L

CAUTION: The gas pressure regulator provided with this appliance must be used. This regulator is set for an outlet pressure of

11 inches water column. (2.7 kPa).

The gas supply must be turned off at the LP-gas supply cylinder when this

6. appliance is not in use.

7.

8.

 

FOR OUTDOOR USE ONLY. If stored indoors, detach and leave cylinder outdoors.

9.

 

Figure 17 Conversion Label

LIGHTING INSTRUCTIONS

1. Locate the control and igniter panel. Make sure the control knob is in the “OFF” position. See Fig.

19. Open the tank door and open the tank valve all the way.

2. Push in the igniter button. You will hear a slight clicking sound. With the igniter button pushed in, push and turn the control knob to the “ON” position. The fire should light within a few seconds. Once the flame is lit, release the igniter button and continue to hold the control knob in for 10 to 15 seconds. Release the control knob. The control knob should pop back out and the fire should remain lit. Note: If the fire does not light, turn the knob to the “OFF” position and wait five

(5) minutes before trying again.

3. To turn down the flame, push the control knob in slightly and turn to the Medium (medium flame) or Low (small flame).

12. To shut down the fire pit, turn the control knob to the “OFF” position and turn off the tank valve

Figure 19

9

MAINTENANCE

The flames should look like those in Fig. 20. To clean the burner, use a soft brush after the burner and lava rocks have cooled completely. Never use a vacuum cleaner on the lava rocks. It is recommended that the lava rocks be stored indoors during the winter if they will be subjected to freezing temperatures. The propane cylinder must be disconnected and removed from the appliance before the appliance can be stored indoors.

Figure 20

BATTERIES

Make sure the control knob is in the “OFF” position. Unscrew the push button cap on the ignition module located on the control panel to access the battery compartment. The ignition module requires one AAA size battery. See Fig. 21.

10

Figure 21

Parts List

Part Number Description

FP0003 ELECTRODE

FP0004 THERMOCOUPLE

FP0008

FP0448

FP0449

NATURAL GAS FLEXIBLE CONNECTION HOSE

FIREPIT BASE

HARDWARE PACK

11

90-DAY LIMITED WARRANTY

What is Covered Under This Warranty?

The item you have purchased is warranted against defects in materials and workmanship for the following parts as outlined below only when unit is installed and operated in accordance with the instructions in this Owner’s Manual and in compliance with local building and fire codes:

 Burner Assembly

 Firepit Base

 Firepit Top

How Do I Obtain Warranty Service?

To obtain warranty service, you must contact our customer service center within the relevant warranty period and provide us with a copy of your dated register receipt as proof of the purchase date. We reserve the right to request photographs and/or return of the defective item(s) and/or such other evidence relating to any claim as we shall reasonably require.

Please call our customer service center at 713-690-1919 for additional warranty claim details and procedures.

What are the Limitations and Exclusions of this Warranty?

Warranty Limitations:

This warranty is subject to the limitation set forth above. In addition, this warranty is made to the original purchaser only and is effective only if items are purchased from one of our authorized dealers. This warranty is not transferable. For warranty replacements based on warranty claims submitted within ninety (90) days of purchase, we will not be responsible for charges associated with shipments outside continental North America at any time or for any reason

Warranty Exclusions: This warranty is subjected to the exclusions set forth above. In addition, the following are excluded from coverage under this warranty: any item used for commercial, contract or any other non-residential purpose; clearance items, display models or items purchased “as is”; freight damage; items subject to misuse, abuse, neglect or lack of proper care or maintenance (including without limitation as provided in any “care and maintenance guide” or similar information we provide); normal wear and tear; damage caused by acts of nature, acts of force majeure, vandalism, fire or other causality, or improper assembly; hardware against corrosion or rusting; purchased or replacement parts; and all plastic parts.

Also excluded are loss of use or time; inconvenience; money; travel; packaging; or incidental, special or consequential damages of any kind. Replacement of defective items or parts as provided herein shall constitute your sole and exclusive remedy for items which are not as warranted. In no event shall our responsibility exceed the purchase price of the item found to be other than as warranted. This warranty is the exclusive statement of your rights with respect to items you have purchased and supersedes any other express warranty or statement, written or oral, made in connection with the purchase and sale of such items. The term ”item” when used herein in the singular refers to the specific piece found to be defective, and not to the entire set of which the item is a part.

Some states do not allow exclusion or limitation of incidental or consequential damage, so that limitation may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.

12

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement