COLONY SOFT

Spread Lavatory Faucet with

Speed Connect™ Drain

Installation

Instructions

3875.409

3875.509

C

Congratulations on purchasing your American Standard faucet with the

Speed Connect drain, a features found only on American Standard faucets.

H

Speed Connect Drain*

• Fewer parts, installs in less time

• Never needs adjustment

• Guaranteed to seal properly the first time, every time.

Certified to comply with ANSI A112.18.1

M 9 6 8 8 8 7 R e v. 1 . 1

*Your new American Standard faucet is designed to work only with the Speed Connect drain.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Recommended tools

Screwdriver Channel Locks Adjustable Wrench Tubing Cutter

1

INSTALL SPOUT

CAUTION

Turn off hot and cold water supplies before beginning.

Insert SPOUT (1) and CABLE CONNECTOR (2) through center hole, making sure the and SEAL WASHER (3) is properly seated in SPOUT (1).

Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT

SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.

Fig. A.

Tighten LOCKNUT (6) firmly. Fig. A.

3

1A

INSTALL VALVE BODY

Place RUBBER RING (9) into SCUTCHEON (10).

Install LOCKNUT (11) onto VALVE BODY (12).

From under side of mounting surface, install VALVE BODY (12) through valve mounting holes. Threads of VALVE BODY (12) should extent at least 5/16 of a inch above mounting surface top. Fig. B. Thread ESCUTCHEON (10) onto VALVE BODY (12) until snug against internal stop. If necessary, adjust

LOCKNUT (11).

Hand tighten LOCKNUT (11) to secure VALVE BODY (12). Repeat above steps for opposite VALVE BODY (12A).

SLOT

10

9

5/16'' MIN.

MOUNTING

SURFACE

10

9

Fig. B.

11

12

12

11

12a

7

1

4

5

6

2

1

2

POP-UP DRAIN

Remove CLEAR PLASTIC COVER (1).

Remove CARDBOARD SPACER (2) from under

DRAIN POP-UP (3).

Tighten TAILPIECE (4) on DRAIN BODY before installing DRAIN BODY. Fig. B.

Fig. A.

1

3

2

3

REMOVE FLANGE

Thread FLANGE (1) counter-clockwise and remove

FLANGE (1) and FOAM GASKET (2) from drain body. Fig. A.

Thread LOCKNUT (3) clock-wise to bottom of drain body. Push GASKET (4) down against

LOCKNUT (3). Fig. B.

Fig. A.

1

2

4

3

Fig. B.

Fig. B.

DRAIN

BODY

4

4

INSTALL DRAIN FROM

BELOW FIXTURE

From under side of SINK install DRAIN BODY (1) up through drain outlet.

Note: No plumber’s putty or caulk is required.

The CABLE ATTACHMENT

POINT (2) must face towards the rear of the SINK.

Install FOAM GASKET (3) and

FLANGE (4) onto drain body from above SINK and tighten

FLANGE (4) firmly.

4

3

REAR OF SINK

DRAIN

OUTLET

1

2

5

TIGHTEN LOCKNUT

Tighten LOCKNUT (1) firmly with Adjustable

Wrench or Channel Locks.

6

FLANGE GASKET AND POP-UP KNOB

Check DRAIN FLANGE in SINK to ensure that

WHITE FOAM GASKET (3) is fully compressed and not visible. Fig. A.

POP-UP KNOB (1) must be fully down. Fig. B.

Fig. A.

WHITE FOAM

GASKET

NOT VISIBLE

DRAIN

FLANGE

Fig. B.

DOWN

1

1

M 9 6 8 8 8 7 R e v. 1 . 1

2

7

ATTACH CABLE CONNECTOR

Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A.

Your new POP-UP DRAIN installation is now complete. Fig. B.

Note: Tailpeice on pop-up drain is 1-1/4” O.D.

Fig. B.

Fig. A.

1

Fig. B.

2

1-1/4” O.D.

8

CHECK OPERATION OF POP-UP

Operate LIFT KNOB (1) to verify that STOPPER (2) opens and closes.

Note: If STOPPER (2) does not open and close properly then refer to the “troubleshooting section” of these instructions.

1

2

9

MAKE WATER SUPPLY AND WASTE CONNECTIONS

NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED

AND MUST BE PURCHASED SEPARATELY.

Thread TEE BODY (4) to SPOUT SHANK (5).

Thread HOSE CONNECTOR (6, 6A) to VALVE CONNECTIONS (7, 7A).

Connect water supply to VALVE BODIES (1,1A) with 1/2" IPS FLEXIBLE

SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use adjustable wrench to tighten connections. Do not over tighten.

Be careful not to kink copper supply when bending. Use tubing cutter to cut to proper length.

Connect HOT water supply to inlet of left SHANK and COLD water supply to right SHANK using sealant, appropriate connectors, and COUPLING NUTS.

Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to waste outlet.

1

1/2" PIPE THREAD

7

6

5

2

FLEXIBLE

SUPPLIES

WASTE

OUTLET

4

HOT

6A

7A

1A

COUPLING

NUT

3

3/8 O.D.

BULL-NOSE

RISERS

COMPRESSION

NUT

FERRULE

COLD

3/8 COMPRESSION

CONNECTION

M 9 6 8 8 8 7 R e v. 1 . 1

3

10

INSTALL HANDLE TRIM

LEVER HANDLE

Turn HANDLE STEM (1) to "OFF" position.

Place the HANDLE ADAPTER (2) on the HANDLE STEM (1). Install the

ADAPTER SCREW (3) and tighten securely.

Position LEVER HANDLE (4) and place on ADAPTER (2). Install the

HANDLE SCREW (5) and tighten securely.

ACRYLIC HANDLE

Turn HANDLE STEM (1) to "OFF" position.

Place the HANDLE ADAPTER (2) on the HANDLE STEM (1).

Position ACRYLIC HANDLE (3) and install onto ADAPTER (2).

Install the HANDLE SCREW (4) and tighten securely.

Push in INDEX BUTTON (5). (Hot-left side , Cold-Right side)

11

TEST INSTALLED FITTING

With HANDLES (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3).

Operate both HANDLES (1) to flush water lines thoroughly.

Replace AERATOR (3).

1

4

5

3

2

1

5

5

4

3

H

2

1

1

3

12

CHECK DRAIN CONNECTIONS

Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. If STOPPER (4) does not seal properly, please refer to “Troubleshooting Guide” in these instructions.

Release POP-UP KNOB (5) down and check all drain connections and "P" trap for leaks. Tighten if necessary.

WASTE

OUTLET

COLD

2

“P” TRAP

2

HOT

13

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN

WITH CLEAR WATER. DRY WITH A SOFT

COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT

WITH SOAPS, ACID, POLISH, ABRASIVES,

HARSH CLEANERS, OR A CLOTH WITH A

COARSE SURFACE.

14

SERVICE

To change direction of handle rotation, proceed as follows:

Turn VALVE to OFF position.

Loosen HANDLE SCREW (1) .

Pull HANDLE (2) off ADAPTER (3). Loosen ADAPTER

SCREW (4) and pull off ADAPTER (3).

Turn ADAPTER (3) 90˚ in a way that flat in ADAPTER (3) catches on the other FLAT on VALVE STEM (5).

Reinstall ADAPTER SCREW (4) and LEVER HANDLE (2).

Tighten HANDLE SCREW (1).

1

2

4

3

5

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90˚.

M 9 6 8 8 8 7 R e v. 1 . 1

4

SpeedConnect™ Drain

Troubleshooting Guide

If sink does not hold water even though Stopper is in the “down” position:

• Follow CABLE ADJUSTMENT PROCEDURE.

If Stopper does not raise up fully or sink drains too slowly:

• Follow CABLE ADJUSTMENT PROCEDURE.

If you need to remove the Stopper:

• Follow STOPPER REMOVAL PROCEDURE.

If you would like the ability to remove your Stopper simply by lifting it out of the drain:

• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.

CABLE ADJUSTMENT PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as

“Cam” in the illustration. Fig. B.

Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the

Stopper should be in the UP position. Fig. B, C.

Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.

Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the

Drain Body Connection (2) and hand-tighten. Fig. A.

Fig. A. Fig. B. Fig. C.

DOWN

CAM 1

RE-ATTACH

1

CAM CAP

STOPPER

DISCONNECT

2

STOPPER REMOVAL PROCEDURE

Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.

Look at the area on the Drain Body where the Cable was attached and locate the component labeled as “Cam” and “Cam Cap” in the illustration. Fig. B.

Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.

Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.

The Stopper can now be removed by lifting it out of the Drain. Fig. F.

Fig. D. Fig. E.

REMOVE

CAM

Fig. F.

REMOVE

CAM CAP

M 9 6 8 8 8 7 R e v. 1 . 1

5

STOPPER INSTALLATION PROCEDURE

The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be removed) or “Unlock” Mode (Stopper is removable).

Locked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. G.

To install the stopper in “Locked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the rear of the

Sink and the American Standard logo is facing front. Rotate

Stopper slightly if necessary so that the Stopper slides all the way down.Fig. G.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

Troubling Shooting Guide to complete installation. Stopper will be in “Locked” mode and not be removable.

LOGO

LOOP TOWARD

REAR OF SINK

DRAIN

Locked Mode

(Vandal Proof)

Fig. G.

Unlocked Mode:

Look at the Plastic Loop at the bottom of the Stopper and notice that the Loop is on one side of the Stopper. Fig. H.

To install the stopper in “Unlocked” mode, insert the Stopper into the Drain so that the Plastic Loop is facing toward the front of the

Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down.

Fig. H.

Re-install the Cam into the Drain, rotating the Cam if necessary to make sure it is fully inserted. Fig. J.

Re-install the Cam Cap, making sure the guide teeth are facing outward. If the Cam Cap does not “snap” into place, then rotate the Cam to make sure it is fully inserted. Fig. K.

Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in

“Troublingshooting Guide” to complete installation. Stopper will be in “Unlocked” mode and removable .

LOGO

LOOP TOWARD

FRONT OF SINK

DRAIN

Fig. H.

Unlocked Mode

Fig. J.

INSTALL CAM

CAM

Fig. K.

INSTALL

CAM CAP

M 9 6 8 8 8 7 R e v. 1 . 1

6

M918504-0070A

SCREW

M908423-0070A

ACRYLIC HANDLE

M916803-YYY0A

METAL LEVER HANDLE

M918075-0070A

HANDLE SCREW

M961643-YYY0A

ESCUTCHEON KIT

M918504-0070A

SCREW

M918021-0070A

ADAPTER

M904900-0070A

VALVE NUT

A954120-0070A

VALVE

M906617-0070A

ATTACHMENT NUT

H

M950144-0070A

INDEX BUTTON, HOT

M950143-0070A

INDEX BUTTON, COLD

M950157-YYY0A

POP-UP ROD

COLONY SOFT

SPREAD LAVATORY FAUCETS

MODEL NUMBER

3875.409

3875.509

M962175-YYY0A

SPOUT KIT

M961639-0070A

SPOUT GASKET

M961733-0070A

SPOUT MOUNTING KIT

066070-YYY0A

AERATOR

M953450-YYY0A

COMPLETE

DRAIN ASSEMBLY

066118-0070A

PIVOT ROD KIT

024220-0070A

SUPPLY NUT

066116-YYY0A

DRAIN STOPPER

066117-YYY0A

2" FLANGE KIT

M950145-YYY0A

LIFT ROD

072574-0070A

EXTENSION ROD

M952425-YYY0A

DRAIN ASSEMBLY

070847-0070A

CLIP

M961711-0070A

TAILPIECE INSERT

070532-0040A

TAILPIECE

POP-UP DRAIN ASSEMBLY

BEFORE 05/06

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-12-00

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

© A S A m e r i c a , I n c . 2 0 0 8

M919660-0020A

6” TAILPIECE

(NOT INCLUDED

WITH FAUCET)

7

M953006-0070A

TUBE & TEE ASSEMBLY

Replace the "YYY" with appropriate finish code

CHROME 002

BRASS 099

CHROME/BRASS 299

M962544-YYY0A

STOPPER

ASSEMBLY

M952430-0070A

CABLE ASSEMBLY

M962457-0070A

FLANGE

ASSEMBLY

M922872-0070A

CAM SEAT INSERT

M962430-0070A

CAM ASSEMBLY

M913207-0070A

TAILPIECE INSERT

A919661-0020A

TAILPIECE

M962458-0070A

DRAIN MOUNTING KIT

M 9 6 8 8 8 7 R e v. 1 . 1