American Standard 7501.170.002 Installation instructions

Instructions

CENTERSET LAVATORY FAUCETS

WITH GOOSENECK SPOUT

7500 Series

7501 Series

7502 Series

7545 Series

Thank you for selecting American-Standard...

the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M

6 0 1 8 5 R e v. 1 . 6

1

CAUTION

Turn off water at main supply.

Asesemble GASKET (1) to SHANKS (2) and insert FAUCET SHANKS through holes of SINK.

Assemble RUBBER (3) and BRASS WASHERS (4), and LOCKNUTS (5) from underside of SINK. Drop

UPPER LIFT ROD (6) through hole in BODY (models 7501 only), align BODY as far forward as possible and secure position by tightening LOCKNUTS (5).

Connect the HOT water supply to the left SHANK and the COLD water supply to the right

SHANK using sealant, appropriate connectors, and COUPLING NUTS (7).

9

8

11

10

To change spout to a swivel spout: (7500, 7501 & 7502)

Unscrew SPOUT NUT (8) and remove SPOUT (9).

Take SPOUT CLIP (10) off SPOUT (9) and remove RUBBER RING (11).

Replace RUBBER RING (11) with seperate PLASTIC RING (12) packed with faucet.

Put SPOUT CLIP (10) on SPOUT.

Reassemble SPOUT (9) to BODY.

BODY

2

GRID DRAIN ASSEMBLY

(Model 7502 only)

Apply a bead of PUTTY around underside of DRAIN PLUG FLANGE (1). Insert DRAIN

PLUG (2) into SINK drain hole.

Hold DRAIN PLUG (2) to prevent turning and assemble GASKET (3), WASHER (4) and LOCKNUT (5) from underneath sink.

PUTTY

1

SINK

4

5

SINK

1

Insert threaded end of TAILPIECE (6) into lower end of DRAIN PLUG (2).

Connect other end to trap.

2

3

INSTALL POP-UP DRAIN

(Model 7501 only) 8

6

HOT

6

7

COLD

12

2

1/2" O.D. SLIP

3

4

5

7

Remove one end of CLIP (12) from PIVOT ROD (7) by squeezing ends together while sliding.

Insert PIVOT ROD (7) into second or third hole in EXTENSION (9) and reassemble CLIP (12).

(EXTENSION may need to be bent.)

Push TAILPIECE (1) down into TRAP

(threaded end up).

Thread LOCKNUT (2), WASHER (3) and

GASKET (4) onto DRAIN BODY (5).

Apply a bead of PUTTY to underside of FLANGE (6).

Feed DRAIN BODY (5) up through SINK and thread FLANGE (6) fully onto BODY (5).

SINK

Tighten LOCKNUT (2) firmly, keeping the

PIVOT ROD (7) pointed towards the back of the SINK.

Drop STOPPER (8) into DRAIN BODY (5).

Pull TAILPIECE (1) up and thread tightly into DRAIN BODY (5).

Position EXTENSION ROD (9) onto POP-UP

ROD (10) and tighten THUMBSCREW (11).

5

2

PUTTY

4

3

1

7

12

7

9

12

TRAP

Adjust STOPPER (8) height by repositioning

EXTENSION and tightening THUMBSCREW (12).

10

11

4

TEST INSTALLED FAUCET Operate both handles to flush water lines thoroughly. Check spout mounting and hose connections for leaks.

Operate LIFT ROD and check DRAIN for leaks.

Remove AERATOR.

With handle in OFF position, turn on water supplies and check all connections for leaks.

Turn handles into OFF position and replace AERATOR.

5

90°

SERVICE

To change direction of handle rotation, proceed as follows:

STOP

WASHER

Turn valve to OFF position.

Remove HANDLE and BONNET NUT.

Remove SPRING CLIP.

Lift STOP WASHER, turn 90° and replace.

Replace SPRING CLIP.

Replace BONNET NUT, HANDLE, SCREW, and INDEX.

AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.

SPRING

CLIP

If spout drips, operate handles several times from OFF to ON position. Do not force - handles turn only 90°.

Plastic SCREEN in CARTRIDGE may accumulate dirt causing reduced water flow. To clean, first turn off hot and cold water supplies, then:

Remove HANDLE and BONNET NUT.

Remove CARTRIDGE by pulling up.

Thoroughly rinse plastic SCREEN at base of CARTRIDGE.

CARTRIDGE

Replace CARTRIDGE until flange is tight against valve body.

Turn valves OFF.

Replace BONNET NUT, HANDLE, SCREW and INDEX.

SCREEN

7500 Series

7501 Series

7502 Series

7545 Series

GRID DRAIN

015025-YYY0A

DRAIN COMPLETE

M922858-0020A

VR AERATOR,

0.35gpm/1.3L/min.

M922880-0020A

AERATOR,

1.5gpm/5.7L/min.

066114 -0020A

VR AERATOR,

0.5gpm/1.9L/min

051214-0070A

SWIVEL/FIXED

SPOUT RINGS

070532-0040A

TAILPIECE

M923208-0070A

FLOW RESTRICTOR

(7500.180, 7500.188

7500.186)

066497-0020A

COMPLETE DRAIN BODY

000690-0020A

HANDLE SCREW

051211-0070A

INDEX KIT

066116-YYY0A

DRAIN STOPPER

POP-UP DRAIN

M918014-0070A

ADAPTER

066117-YYY0A

FLANGE KIT

072574-0070A

EXTENSION ROD

070847-0070A

CLIP

066118-0070A

PIVOT ROD

0-RING

900864-0070A

DRAIN BODY

TAILPIECE INSERT

070532-0070A

TAILPIECE

6 0 1 8 5 R e v. 1 . 6

M919646-0020A

SPOUT

051322-0020A

VANDAL PROOF SCREW

000690-0020A

HANDLE SCREW

051211-0070A

INDEX KIT

051217-0020A

WRIST BLADE

HANDLE KIT

M918014-0070A

ADAPTER

012087-0070A

SPOUT SEAL KIT

904939-0020A

BONNET NUT

051210-0020A

LEVER HANDLE

028617-0020A

POP-UP ROD

951764-0070A

CARTRIDGE

911928-0070A

GASKET

M919658-0020A

8" SPOUT

(7500.188)

M964387-0020A

8" SPOUT

(7500.177)

A919641-0020A

5" SPOUT

(7500.180)

M919246-0020A

6" SPOUT

(7500.186)

030255-0070A

MOUNTING KIT

024220-0070A

COUPLING NUT

HOT LINE FOR HELP

For toll-free information and answers to your questions, call:

1-800-442-1902

Weekdays 8:00 a.m. to 6:00 p.m. EST

IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)

Weekdays 8:00 a.m. to 7:00 p.m. EST

IN MEXICO 01-800-839-1200

P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A m e r i c a n S t a n d a r d I n c .

© A S A m e r i c a , I n c . 2 0 0 8