SpeedStream® 2623 Wireless DSL/Cable Router

SpeedStream® 2623 Wireless DSL/Cable Router
Tips and Troubleshooting
Connection Configuration for DSL service users:
Most DSL service providers supply users with a dynamic IP address, but require a valid username and password to be
entered first. This method is known as PPP over Ethernet (PPPoE).
Note: If your service provider currently requires you to use separate PPPoE client software, discontinue use of this software and complete
the following procedure to configure the SpeedStream router to negotiate the PPPoE logon to your service provider’s network.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
Connect to the SpeedStream router's configuration interface by entering HTTP:// 192.168.254.254 and
press Enter.
You will see the SpeedStream Router Status screen. Select Simple Setup from the left-side menu and choose
WAN from the expanded menu.
Select PPPoE and click Enter.
Enter the Username and Password exactly as provided by your DSL service provider, leave the Service Name
field blank and click Enter.
Wait approximately 10 seconds, then click the Status link in the left-side menu.
On the SpeedStream Router Status page, check the Internet connection status section for the field labeled
Cable/DSL. Ensure that the status says Connected.
• If it says Connected, you have successfully obtained an IP Address from your DSL service provider and may
proceed with using the router and Internet service as desired.
• If it says Disconnected, continue to the next step.
Power off both the DSL modem and the SpeedStream router.
Power on both the DSL modem and the SpeedStream router.
Connect to the SpeedStream router's configuration interface by entering HTTP:// 192.168.254.254 and
click Enter.
On the SpeedStream Router Status page, check the Internet connection status section for the field labeled
Cable/DSL. Ensure that the status says Connected.
• If it says Connected, you have successfully obtained an IP Address from your DSL service provider and may
proceed with using the router and Internet service as desired.
• If it says Disconnected, continue to the next step.
Troubleshooting:
• Ensure that the DSL modem is securely connected to the router and the modem is powered on and
functioning properly.
• Ensure that the Username and Password entered are accurate- verify with your DSL service provider, if
necessary.
• Upgrade the firmware on the SpeedStream router to the latest version available.
007-0097-002
8.
9.
10.
11.
12.
13.
13.
Select Simple Setup from the left-side menu and choose WAN from the expanded menu.
Select Dynamic IPAddress and click Enter.
Click the Clone MAC Address button.
Click Enter.
Wait approximately 10 seconds, then click the Status link in the left-side menu.
On the SpeedStream Router Status page, check the Internet connection status section for the field labeled
Cable/DSL. Ensure that the status says Connected.
• If it says Connected, you have successfully obtained an IP Address from the @Home service and may proceed
with using the router and Internet service as desired.
• If it says Disconnected, continue to the next step.
Troubleshooting:
• Ensure that the Cable modem is securely connected to the router and the modem is powered on and
functioning properly.
• Ensure that the HOST NAME entered is accurate- verify with @Home, if necessary.
• Upgrade the firmware on the SpeedStream router to the latest version available.
PC Setup—Windows® 95/98/98SE/Me
TCP/IP Setup
1.
2.
3.
4.
Right-click on the Network Neighborhood icon on your desktop, select Properties.
Select the TCP/IP->Ethernet Adapter entry.
Ensure Obtain an IP Address Automatically is selected. The DHCP server in the SpeedStream router will provide
an IP address for the PC.
Click OK twice, then restart your PC even if no changes were made.
Internet Access
1.
2.
3.
4.
5.
6.
Select Start Menu-> Settings-> Control Panel-> Internet Options.
Select the Connections tab and click the Setup button.
Select I want to set up my Internet connection manually, or
I want to connect through a Local Area Network (LAN) and click Next.
Select I connect through a Local Area Network (LAN) and click Next.
Uncheck all boxes on the Local Area Network Internet Configuration screen and click Next.
Follow the remaining prompts until the wizard has finished.
Connection Configuration for @Home™ cable modem service users:
1.
2.
3.
4.
5.
6.
7.
Obtain your exact HOST NAME from @Home™ or your Windows Network Control Panel
Connect to the SpeedStream router's configuration interface by entering HTTP:// 192.168.254.254 and
press Enter.
You will see the SpeedStream Router Status screen. Select Simple Setup from the left-side menu and choose
WAN from the expanded menu.
Select Dynamic IPAddress and click Enter.
Enter the HOST NAME you were provided by @Home and click Enter.
Wait approximately 10 seconds, then click the Status link in the left-side menu.
On the SpeedStream Router Status page, check the Internet connection status section for the field labeled
Cable/DSL. Ensure that the status says Connected.
• If it says Connected, you have successfully obtained an IP Address from the @Home service and may proceed
with using the router and Internet service as desired.
• If it says Disconnected, continue to the next step.
Technical Support for North America is available 24 hours a day, 7 days a week, by phone, email or online:
Phone:
Email:
Online:
SpeedStream® 2623
Wireless DSL/Cable Router
1-877-823-6722
[email protected]
http://www.support.speedstream.com
For more information regarding SpeedStream® products visit: www.speedstream.com.
Efficient Networks, Inc.
A Siemens Company
4849 Alpha Road
Dallas, TX 75244
©2001 Efficient Networks, Inc. All rights reserved. Efficient Networks, its logos, "Live a Broadband Life" and SpeedStream are registered and
unregistered trademarks of Efficient Networks, Inc. Siemens and the Siemens logo are registered trademarks of Siemens AG, Germany. All other
brand names and trademarks are held by their respective companies. Efficient Networks reserves the right to make changes to product
specifications at any time without notice.
Quick-Start Guide
Before you begin:
Step
1.
Hardware Installation
Step
Ensure that the SpeedStream 2623 is powered OFF before commencing with installation. Leave
your DSL/Cable modem connected to its wall socket (phone line or cable outlet).
Use Cat 5 Ethernet cable(s) to connect PC(s) and/or a hub or switch to one of the LAN ports on the
SpeedStream router.
Package Contents
Your package includes the following:
1
2.
AND/OR
Use an 802.11b compatible wireless access device to connect PC(s) to the router using the
wireless method.
1.
2.
3.
4.
5.
Note: In order to connect to the router, the wireless settings of each wireless adapter in use must match those of the SpeedStream
router. Below are the default settings of the SpeedStream wireless router:
1
2
SSID: SpeedStream
Channel: 11
WEP: Disabled
Connect your DSL/Cable modem to the WAN port on the SpeedStream router using the Ethernet
cable supplied with your DSL/Cable modem. If no cable was supplied with your modem, use a
straight-through Ethernet cable.
3
3.
SpeedStream 2623 Wireless DSL/Cable Router
AC Power Adapter
Note: An ISDN TA or dial-up modem may be connected to the SpeedStream wireless router as an alternate method of Internet access.
Please refer to the User’s Guide on CD for directions on using/configuring this type of connection.
4.
5.
FREE
6.
E X T E N D E D WA R R A N T Y !
LAN
®
m
SpeedStrea
Power
WAN
Connect the power adapter to the SpeedStream 2623. Use only the power adapter provided.
(optional) If you intend to use the SpeedStream wireless router's print server functionality, connect
the parallel cable of the printer to the printer port on the router before powering on the router.
Power ON the SpeedStream wireless router.
10/100
1
2
3
4
1.
O N Y O U R S P E E D S T R E A M P R O D U C T.
SpeedStream
ions
SpeedStream® Quic
®
www.speedstream.com/reg/extwrnty
Software CD-ROM
L i v e
k-Start Guide
a
B r o a d b a n d
2
L i f e ™
to
ere
th isw whcat ion
epto kno
L eduo.
KePC
r
t, DS t inf
r you por duc
neafor sup pro
go and new
,
2.
Wireless
Method
w w w . s p e e d s t r e a m . c o m
007-0105-002
This offer may be revoked, amended, supplemented, revised, altered, changed or terminated at any time without notice in the sole and absolute
discretion of Efficient Networks, Inc. This offer is available on select products only. This offer is available in select countries only. The offer is
good for thirty (30) days from the date of installation. Offer void where prohibited by law. Certain restrictions may apply.
3.
© 2001 Efficient Networks, Inc. A Siemens Company
Safety and
Certifications
Information
Quick-Start Guide
Documentation/
Printer Port Driver CD
Extended Warranty
and Registration Card
4.
Back View
PC(s)
This guide covers only the most common situations. Please refer to the full User’s Guide on the CD-ROM
if your network uses any of the following: existing router, existing DHCP server, or PC(s) using fixed (static)
IP addresses
Printer
COM
T
RESE
PRIN
WA N
1
2
3
5V AX
2A M
4
TER
Requirements:
Broadband Modem
PC(s) with the TCP/IP protocol installed
Cat 5 Ethernet cables with RJ-45 connectors
Wireless network adapter for each PC that will be wirelessly connected to the network
5
3
DSL/Cable
modem
2
Wired
Method
PC(s) and/or
hub or switch
Perform TCP/IP Setup for each PC as described in the PC Setup section of this guide.
Remember to restart each PC when finished.
Start your web browser. In the Address box, enter the following: HTTP:// 192.168.254.254
Press Enter. You will be prompted for a Password- The default Password is admin
When the password is entered correctly, you will see the SpeedStream Router Status screen.
Select Simple Setup from the left-side menu and follow the prompts to change the password, set
the Time Zone and choose the appropriate Internet connection type. For detailed procedures
covering the most common broadband Internet access scenarios, refer to the procedures
provided on the back side of this guide.
Step
G E T A O N E Y E A R H A R D WA R E WA R R A N T Y E X T E N S I O N
JUST GO TO
Internet Connection Configuration
If additional configuration is desired, select the Advanced Setup link from the left-side menu to configure
firewall parameters, Wireless Encryption Protocol (WEP) strength, DMZ host, virtual servers and special
application support for multi-player online games.
Link/ACT
Reset
Safety and Certi
ficat
2
3
Printer Port Driver Installation (optional)
Ensure that the printer is connected to the parallel port on the router and both the printer and
router are powered on.
Insert the supplied CD-ROM into your CD-ROM drive. If the setup program does not start
automatically, run SETUP from the root folder on the CD-ROM.
Consult the User Guide on CD-ROM for step-by-step installation and configuration instructions
specific to your operating system.
Repeat the procedure for each PC that will share the printer.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement