MICAS_Data sheet_Autolight pl
HF MOTION DETECTOR FOR LUMINAIRES
Motion detector for professional use
Particularly suitable for
professional use with higher
electric loads
Implemented immunity against
other sensors in the same
detection field
Simple settings in predefined
steps via push buttons
Program Mode for setting of
individual brightness
thresholds
llllllllllllllllllllllllllll is an innovative 5.8 GHz HF motion detector for switching
luminaires with any kind of illuminants in a very energy efficient way (e.g. LEDs,
fluorescent lamps, incandescent lamps). It is particularly suitable for professional
use with higher electric loads and special requirements for the detection field of
the sensor.
This product has a compact-sized and solid standard casing with a special grouting
compound for a long-life product quality. Simple settings can be adjusted in
predefined steps for sensitivity, hold time, brightness sensor (with Program
Mode-function) as well as special settings via user friendly push buttons with LED
feedback. The high quality relay is particularly suitable for commercial use with
switching power up to 500 VA for LEDs and fluorescent lamps and up to 800 W for
incandescent lamps.
Llllllllllllllllllllllllllllll is compatible to common quality electronic ballasts as well as for
MICAS master/slave radio technology for luminaires. Customized versions are
available on demand.
Range up to
HF technology
16 m
5.8 GHz
Autolight plus enables a
range of up to 16 m.
The high-frequency
sensors operate in a
frequency range of
5.8 GHz.
Program
Mode
The program mode
measures and stores
current brightness
conditions as a
threshold.
Emitted power
< 5 mW
The emitted power of
the sensor is less than
5 mW.
Inrush
Relay
High quality relay,
suitable for high inrush
applications.
© MICAS AG - non-binding data sheet, subject to changes, applicable for deliveries starting 12/2013
SOLUTIONS FOR
LIGHT CONTROL
AUTOLIGHT plus
Operating voltage
230 V +/- 10%, 50 Hz
Switching power
800 W incandescent lamps
500 VA fluorescent lamps
500 VA LED
400 A / 200 µs inrush current or
max. 10 electronic ballasts
Sensor principle
HF motion detector
Frequency range
5.8 GHz +/- 75 MHz
up to 16m
2,6m
1,8m
up to 14m
Wall
Ceiling
Power loss at power off
< 1.3 W
state (active power)
Emitted power
< 5 mW
Interfaces
3-pole plugable clamp terminal (N, L, L’)
for 1.5 mm² cable
Measures
110 x 41 x 27.5 mm (LxWxH)
Brightness levels
daylight / 300 lux / 150 lux
twilight / darkness / program mode
Mounting height
max. 2.7 m (wall)
max. 4.0 m (ceiling)
Sensitivity
20 / 30 / 50 / 75 / 100 %
Hold time
10 / 60 / 180 / 300 / 600 / 900 / 1800 s
Test mode
2 s hold time
Operating temperature
-20°C ...+70°C
IP rating
IP 20 (mounting inside a luminaire)
Characteristics
- adjustable, rotationally symmetric and conical
detection field with up to 16 m of frontal length as
well as a 14 m diameter for a wall mounting height
of 1.8 m or a ceiling mounting height of 2.6 m
(depending on the kind of luminaire, installation
circumstances and mounting conditions)
- test mode for checking the sensor functionality
- implemented temperature protection
N
AUTOLIGHTplus
L
HF MOTION DETECTOR
L
+
Sensitivity
Hold time
Brightness value
Red indicator LED
Brightness sensor
Terminal clamps
Mounting bracket
HF antenna
Mounting bracket
MICAS
WATER
EFFICIENCY
ENERGY
EFFICIENCY
COLLISION
AVOIDANCE
Product
Quality
© MICAS AG - non-binding data sheet, subject to changes, applicable for deliveries starting 12/2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement