INSTRUCTION MANUAL
Before commencing assembly, please read these instructions thoroughly.
Wing Span: 81 in / 2050mm
Wing Area: 1020 sq in / 65.8 sq dm
Flying Weight: 9 lbs / 4100 g
Fuselage Length: 61 in / 1560mm
Radio required: 4 - stroke 0.91 engine
4 - channel radio w/ 5 servos
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
www. thewingsmaker. com
GA011
I N D E X
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
1
2
3
Apply epoxy glue.
Assemble left and right sides the same way.
Peel off shaded portion covering film.
3mm
Drill holes with the specified diameter (here: 3mm).
Pay close attention here!
Pierce the shaded portion covering film.
P . 1
Apply instant glue
(C.A.glue, super glue.)
Ensure smooth non-binding movement while assembling.
Cut off shaded portion.
Must be purchased separately!
Do not overlook this symbol!
P. 1
P. 2
P. 3 -9
P. 10
Parts List
1. MAIN WING -- 1 pair
2. SCREW PM2 X 20mm -- 2 pcs
SCREW PM2 X 25mm -- 4 pcs
PUSHROD Ø1.8 x 106mm w/ Threads (For Aileron) -- 2 pcs
TRI-HORN M3 X 14mm (L) -- 2 sets
CLEVIS -- 2 pcs
STRAPER -- 2 pcs
FUEL TUBE Ø6 X 5mm -- 4 pcs
3. MAIN LANDING GEAR -- 1 pair
MAIN LANDING GEAR COVER -- 1 set
MOUNTING PLATE 12 X 20mm -- 4 pcs
SCREW PA3 X 14mm -- 8 pcs
SCREW PM2 X 8mm -- 8 pcs
WASHER d2 X D5mm -- 16 pcs
M2 NUT -- 8 pcs
4. SCREW PA3 X 12mm -- 4 pcs
COLLAR Ø5.1mm w/ Set screw -- 4 sets
MAIN WHEEL Ø90mm -- 2 pcs
WHEEL PANTS -- 1 pair
MOUNTING PLATE 12 X 20mm -- 2pcs
5. WING TUBER Ø18 X 701mm -- 1 pc.
6. STABILIZER & ELEVATOR -- 1 set
SCREW PM3 X 25mm -- 1 pc.
WASHER d3 X D7mm -- 1 pc.
FUSELAGE -- 1 pc.
7. VERTICAL FIN & RUDDER -- 1 set
8. TAIL LANDING GEAR -- 1 set
TAIL WHEEL Ø25mm -- 1 pc.
SCREW PA3 X 12mm -- 2 pcs
COLLAR Ø2.1mm w/ Set screw -- 1 set
SCREW PM2 X 14mm -- 1 pc.
WASHER d2 X D5mm -- 2 pcs
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.3mm -- 1 pc.
9. FUEL TANK 450CC -- 1 set
BALSA 8 x 10 x 116mm (For fixing fuel tank) -- 1 pc.
10. ENGINE MOUNT (PL5911120) -- 1 set
SOCKET HEAD SCREW M6 X 30mm -- 4 pcs
WASHER d6 X D15mm -- 4 pcs
11. THROTTLE PUSHWIRE Ø1.2 x 340mm
w/Plastic tube d2 x D3 x 185mm -- 1 set
ALUMINUM PLATE (For Engine Mount) – 1pc.
ANTI - VIBRATION MOUNT -- 1 set
INCLUDE: SCREW M4 X 35mm -- 4 pcs
SCREW KM3 X 20mm -- 8 pcs
WASHER d4 X D12mm -- 8 pcs
M3 NYLON INSERT LOCK NUT -- 8 pcs
M4 NYLON INSERT LOCK NUT -- 4 pcs
P. 2
12. COWLING -- 1 set
TRANSPARENT DUMMY COWLING -- 1 set
PWA2.6 X 12mm -- 5 pcs
SILICON GROMMET d1.5 X D6.5mm -- 5 pcs
SPINNER Ø70mm -- 1 set
13. WIRE Ø1 x 900mm (For Rudder) -- 2 pcs
COPPER TUBE d2.5 X D3.2 X 8mm -- 2 pcs
RIGGING COUPLER Ø1.8 X 27mm w/ Threads (For Rudder) -- 2 pcs
SCREW PM2 X 16mm -- 3 pcs
M2 NUT -- 3 pcs
TRI-HORN M3 X 14mm (L) (w/ o - Base For Rudder) -- 2 sets
FUEL TUBE Ø6 X 5mm -- 2 pcs
CLEVIS -- 2 pcs
14. PUSHROD Ø1.8 x 660mm w/ Threads (For Elevator) -- 2 pcs
TRI-HORN M3 X 4mm (L) -- 2 sets
SCREW PM2 X 16mm -- 6 pcs
CLEVIS -- 2 pcs
FUEL TUBE Ø6 X 5mm -- 2 pcs
15. LINKAGE CONNECTOR Ø2.1mm -- 1 set
16. SPONGE 60 X 70 X 115mm -- 1 pc.
RIGGING Z BEND Ø1.8 x 27mm (For Rudder) -- 2 pcs
PUSHROD Ø1.8 x 170mm (For Elevator) -- 1 pc.
COPPER TUBE d2.5 X d3.2 X 8mm -- 2 pcs
STRAPER -- 1 pc.
FUEL TUBE Ø6 X 5mm -- 1 pc.
PLYWOOD 120 X 35 X 6mm (For Throttle Servo) -- 1 pc.
BALSA 6 x 6 x 35 (For Throttle Servo Stand) -- 2 pcs
PUSHROD CONNECTOR 8 X 9 X 20mm -- 1 set
17. CANOPY -- 1 set
SCREW PWA2.3 X 8mm -- 8 pcs
SILICON GROMMET d1.5 X 6.5mm -- 8 pcs
PILOT PL001085A/B -- 1 pc.
18. SCREW PM4 X 35mm -- 2 pcs
WASHER d4 X D15mm --2 pcs
PLYWOOD 2 x 30 x 120mm (Wing Protection) -- 1 pc.
19. DECALS -- 1 set
COVERING:--
TOUGHLON STL204 CREAM
TOUGHLON STL310 RED
TOUGHLON STL402 CHECKER BLACK/WHITE
TOUGHLON STL571 RICH GOLD
1
Main Wing
Pre-glued
Bottom View
2
Aileron Servo
PM2 x 20mm Screw
2
PM2 x 25mm Screw
4
straper
1.5mm
PM2x25mm
PM2x25mm
Clevis
Fuel Tube
Ø6x5mm
2mm
Pushrod
Ø1.8x106mm
Tri-horn
M3x14mm
Ø1mm pilot holes for The Wings Maker tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
Bottom View
3
Main Landing Gear
PA3 x 14mm Screw
8
PM2 x 8mm Screw
8
d2 x 5mm Washer
16
M2 Nut
8
2
PA3 x 14mm mm Washer
PM2 x 8mm
M2 NUT
Plate
P. 3
Bottom View
4
Main Landing Gear
PA 3 x 12mm Screw
4
3mm Set Screw
4
5.1mm Collar
4
Completed
3mm Set Screw
Ø5.1mm Collar
PA3 x 12mm
Wheel Ø90mm
Bottom View
5
Main Wing
Wing Tuber
Ø18 x 701mm
Bottom View
6
d3 x D7mm Washer
1
PM3 x 25mm Screw
1
PM3 x 25mm d3 x D7mm
Pre-glued
1.
Apply thread locker to screws.
2.
3.
4.
Bottom View
Pre-glued
Bottom View
Complete
P. 4
7
Pre-glued
C
C
C=C'
Completed
8
Tail Landing Gear
PA 3 x 12mm Screw
2
3mm Set Screw
1
2.1mm Wheel Collar
1
PM2 x 14mm Screw
1
d2 x D5mm Washer
2
M2 Nut
1
PA3 x 12mm
WHEEL Ø25mm
2.1mm Wheel Collar
3 x 3mm Set Screw
M2 Nut
PM2 x 14mm d2 x D5mm Washer
2mm
9
Fuel Tank
Install Balsa 8 x 10 x 116mm
(For fixing fuel tank)
Fuel Tank
450cc
Fuel Tank
450cc
Fuel Tank 450cc
Bottom View
Install Balsa
8 x 10 x 116mm
(For fixing fuel tank)
P. 5
10
Engine Mount
M6 x 30mm Socket Head Screw
4
d6 x D15mm Washer
4
M6 x 30mm
Socket Head Screw d6 x D15mm
Washer
Apply thread locker to screws
Blind nuts are off-centered to keep the spinner at the fuselage axis.
Engine Mount
Pl5911120
11
Engine
M4x35mm SOCKET HEAD SCREW
4
KM3x20mm Screw
8
M4 Nylon Insert Lock Nut
4
M3
Nylon Insert Lock Nut
8
d4 x D12mm Washer
8
Install Engine Position
142mm
5.6in.
M4 Nylon
Insert Lock Nut
d4 x D12mm
Washer
M4 x 35mm
SOCKET HEAD SCREW
ANTI-VIBRATION MOUNT INSTALLATION
KM3 x 20mm
Make sure the rounded edges are facing the shock absorbing
SILICON PAD.
3mm
P. 6
Plastic Tube d2 x D3 x 185mm
Throttle Push wire
1.2 x 340mm
12
Cowling
PWA2.6 x 12mm Screw
5 d1.5 x D6.5mm Silicon Grommet
5
First insert the grommet to the cowling then apply screw.
Spinner
1mm
d1.5 x D6.5 mm
Silicon Grommet
PWA2.6 x 12mm
13
Rudder Pullwire
PM2 x 16mm Screw
3
M2 Nut
3
Ø1mm pilot holes for The Wings Marker tri-horn are pre-drilled.
Please look for pin-hole marks at side of control surfaces.
≈135mm
2mm
Tri-horn
Wire Ø1 X 900mm
Bottom View
14
Elevator Pushrod
PM2 X 16mm Screw
6
PM2 X 16mm
Pushrod Ø1.8 X 660mm
w/Threads
Clevis
Fuel Tube
Ø1mm pilot holes for The Wings Marker tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
2mm
≈180mm
Tri-horn
Bottom View
P. 7
15
Servo Set
LINKAGE CONNECTOR
3 x 3mm Set Screw
1
Linkage Connector
1
2mm Nut
1
2mm Washer
2
Throttle Rod
2mm
2mm
3mm
Included with the Radio Set.
Throttle Servo.
Please refer to attached sheet for linkage connector installation.
16
Radio Equipment
Install and arrange the servo as shown in the diagram.
Copper Tube
Press down the center
1/3 portion
Front
Balsa 6 x 6 x 35mm
Spong 60 X 70 X 115mm
Rudder Servo
Copper
Tube
Pushrod Connector
8 X 9 X 20mm
Throttle
Servo
Balsa 6 x 6 x 35mm
Plywood
35 x 6 x 120mm
Elevator Servo
Straper
Fuel Tube
Pushrod 1.8 X 170mm
Wire
Ø1 X 900mm
Rigging Z Bend
Ø1.8 x 27mm
Bottom View
M2 Nut
Elevator Pushrod
Ø1.8x170mm
Elevator Servo
Bottom View
P. 8
KM 2x8mm
17
Canopy
PWA2.3 x 8mm Screw
8 d1.5 x D6.5mm Silicon Grommet
8
PWA2.3 x 8mm d1.5xD6.5mm
Silicon Grommet
18
Main Wing
PM4 x35mm Screw d4xD15mm Washer
2
2
PM4x35mm d4xD15mm
Washer
4mm
Bottom View
First insert the grommet to the canopy then apply screw.
Front
Pilot
1mm
Front
P. 9
Completed
19
Wing Setting
Adjust the wing and fuselage configuration as shown in the diagrams.
C
B B '
C '
A = A ' B = B ' C = C '
20
Control Throws
Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference.
Elevator
20mm
20mm
Rudder
44mm
44mm
Aileron
9mm
9mm
P. 10
www. thewingsmaker. com
21
C.G
The ideal C.G. Position is 108mm (4.25 in) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.
108mm
4.25 in.
Important Safety Precautions
First time flyer should never fly by himself / herself. Assistance from experienced flyer is absolutely necessary.
Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly pre-adjusted aircraft.
glow engine, using a more powerful engine does not mean better performance. In fact, over powered engine may cause severe damage and injuries.
Make sure the air field is spacious, never fly the plane too close to people and never get too close to a running propeller.
If you find wrinkles on the covering as a result of weather changes, you can use hot iron to remove the wrinkles. Please begin with lower temperature setting and gradually raise the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
Check and re-tighten up all factory assembled screws, use thread locker if applicable.
GA0110610
THE WINGS MAKER
P.11
