GPD125-A - Yamaha Motor Europe

GPD125-A - Yamaha Motor Europe
Read this manual carefully before operating this vehicle.
OWNER’S MANUAL
GPD125-A
2DS-F8199-E0
[English (E)]
DIC183
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
EAU46091
Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Introduction
EAU10114
Welcome to the Yamaha world of motorcycling!
As the owner of the GPD125-A, you are benefiting from Yamaha’s vast experience and newest technology regarding the
design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.
Please take the time to read this manual thoroughly, so as to enjoy all advantages of your GPD125-A. The Owner’s Manual
does not only instruct you in how to operate, inspect and maintain your scooter, but also in how to safeguard yourself and
others from trouble and injury.
In addition, the many tips given in this manual will help keep your scooter in the best possible condition. If you have any
further questions, do not hesitate to contact your Yamaha dealer.
The Yamaha team wishes you many safe and pleasant rides. So, remember to put safety first!
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your scooter and this
manual. If there is any question concerning this manual, please consult a Yamaha dealer.
EWA12412
WARNING
Please read this manual carefully and completely before operating this scooter.
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Important manual information
EAU10134
Particularly important information is distinguished in this manual by the following notations:
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.
WARNING
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
NOTICE
A NOTICE indicates special precautions that must be taken to avoid damage to the
vehicle or other property.
TIP
A TIP provides key information to make procedures easier or clearer.
*Product and specifications are subject to change without notice.
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Important manual information
EAUN0430
GPD125-A
OWNER’S MANUAL
©2015 PT Yamaha Indonesia Motor
Manufacturing
1st edition, April 2015
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
PT Yamaha Indonesia Motor Manufacturing
is expressly prohibited.
Printed in Indonesia.
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Table of contents
Safety information............................ 1-1
Further safe-riding points ............... 1-5
For your safety – pre-operation
checks ...............................................4-1
Description ....................................... 2-1
Left view ......................................... 2-1
Right view....................................... 2-2
Controls and instruments ............... 2-3
Operation and important riding
points .................................................5-1
Starting the engine..........................5-1
Starting off ......................................5-2
Acceleration and deceleration ........5-2
Braking............................................5-2
Tips for reducing fuel
consumption................................5-3
Engine break-in ...............................5-3
Parking ............................................5-4
Instrument and control functions... 3-1
Main switch/steering lock............... 3-1
Keyhole shutter .............................. 3-2
Indicator lights and warning
lights............................................ 3-2
Multi-function meter unit ................ 3-4
Handlebar switches...................... 3-10
Front brake lever .......................... 3-10
Rear brake lever ........................... 3-11
ABS .............................................. 3-11
Fuel tank cap................................ 3-12
Fuel............................................... 3-13
Fuel tank overflow hose ............... 3-14
Catalytic converter ....................... 3-14
Seat .............................................. 3-15
Storage compartments................. 3-16
Sidestand ..................................... 3-17
Ignition circuit cut-off system....... 3-17
Periodic maintenance and
adjustment ........................................6-1
Owner’s tool kit ...............................6-1
Periodic maintenance chart for
the emission control system........6-2
General maintenance and
lubrication chart...........................6-3
Removing and installing panels ......6-7
Checking the spark plug .................6-8
Engine oil and oil strainer..............6-10
Final transmission oil.....................6-12
Coolant..........................................6-13
Air filter and V-belt case air filter
elements ....................................6-16
Checking the throttle grip
free play .....................................6-18
Valve clearance .............................6-19
Tires .............................................. 6-19
Cast wheels .................................. 6-21
Checking the front and rear
brake lever free play.................. 6-21
Checking the front and rear
brake pads ................................ 6-22
Checking the brake fluid level ...... 6-22
Changing the brake fluid .............. 6-24
Checking the V-belt ...................... 6-24
Checking and lubricating the
cables........................................ 6-24
Checking and lubricating the
throttle grip and cable ............... 6-25
Lubricating the front and rear
brake levers............................... 6-25
Checking and lubricating the
centerstand and sidestand........ 6-26
Checking the front fork................. 6-26
Checking the steering................... 6-27
Checking the wheel bearings ....... 6-27
Battery .......................................... 6-28
Replacing the fuses ...................... 6-29
Headlight ...................................... 6-30
Replacing an auxiliary light
bulb ........................................... 6-31
Brake light..................................... 6-32
Replacing the taillight bulb ........... 6-32
Replacing a front turn signal
light bulb.................................... 6-34
Replacing a rear turn signal
light bulb.................................... 6-35
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Table of contents
Troubleshooting ............................6-36
Troubleshooting charts .................6-37
Scooter care and storage ................7-1
Matte color caution .........................7-1
Care .................................................7-1
Storage ............................................7-4
Specifications....................................8-1
Consumer information .....................9-1
Identification numbers.....................9-1
Index ................................................10-1
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Safety information
EAU1026B
1
Be a Responsible Owner
As the vehicle’s owner, you are responsible for the safe and proper operation of your scooter.
Scooters are single-track vehicles.
Their safe use and operation are dependent upon the use of proper riding
techniques as well as the expertise of
the operator. Every operator should
know the following requirements before riding this scooter.
He or she should:
 Obtain thorough instructions from
a competent source on all aspects
of scooter operation.
 Observe the warnings and maintenance requirements in this Owner’s Manual.
 Obtain qualified training in safe
and proper riding techniques.
 Obtain professional technical service as indicated in this Owner’s
Manual and/or when made necessary by mechanical conditions.
 Never operate a scooter without
proper training or instruction. Take
a training course. Beginners
should receive training from a certified instructor. Contact an authorized scooter dealer to find out
about the training courses nearest
you.
Safe Riding
Perform the pre-operation checks
each time you use the vehicle to make
sure it is in safe operating condition.
Failure to inspect or maintain the vehicle properly increases the possibility of
an accident or equipment damage.
See page 4-1 for a list of pre-operation
checks.
 This scooter is designed to carry
the operator and a passenger.
 The failure of motorists to detect
and recognize scooters in traffic is
the predominating cause of automobile/scooter accidents. Many
accidents have been caused by
an automobile driver who did not
see the scooter. Making yourself
1-1
conspicuous appears to be very
effective in reducing the chance of
this type of accident.
Therefore:
• Wear a brightly colored jacket.
• Use extra caution when you are
approaching
and
passing
through intersections, since intersections are the most likely
places for scooter accidents to
occur.
• Ride where other motorists can
see you. Avoid riding in another
motorist’s blind spot.
• Never maintain a scooter without proper knowledge. Contact
an authorized scooter dealer to
inform you on basic scooter
maintenance. Certain maintenance can only be carried out
by certified staff.
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Safety information
 Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current driver’s license.
• Make sure that you are qualified
and that you only lend your
scooter to other qualified operators.
• Know your skills and limits.
Staying within your limits may
help you to avoid an accident.
• We recommend that you practice riding your scooter where
there is no traffic until you have
become thoroughly familiar with
the scooter and all of its controls.
 Many accidents have been
caused by error of the scooter operator. A typical error made by the
operator is veering wide on a turn
due to excessive speed or undercornering (insufficient lean angle
for the speed).
• Always obey the speed limit and
never travel faster than warranted by road and traffic conditions.
• Always signal before turning or
changing lanes. Make sure that
other motorists can see you.
 The posture of the operator and
passenger is important for proper
control.
• The operator should keep both
hands on the handlebar and
both feet on the operator footrests during operation to maintain control of the scooter.
• The passenger should always
hold onto the operator, the seat
strap or grab bar, if equipped,
with both hands and keep both
feet on the passenger footrests.
Never carry a passenger unless
he or she can firmly place both
feet on the passenger footrests.
 Never ride under the influence of
alcohol or other drugs.
 This scooter is designed for onroad use only. It is not suitable for
off-road use.
1-2
Protective Apparel
The majority of fatalities from scooter
accidents are the result of head injuries. The use of a safety helmet is the
single most critical factor in the prevention or reduction of head injuries.
 Always wear an approved helmet.
 Wear a face shield or goggles.
Wind in your unprotected eyes
could contribute to an impairment
of vision that could delay seeing a
hazard.
 The use of a jacket, substantial
shoes, trousers, gloves, etc., is effective in preventing or reducing
abrasions or lacerations.
 Never wear loose-fitting clothes,
otherwise they could catch on the
control levers or wheels and cause
injury or an accident.
 Always wear protective clothing
that covers your legs, ankles, and
feet. The engine or exhaust system become very hot during or after operation and can cause
burns.
 A passenger should also observe
the above precautions.
1
U2DSE0E0.book Page 3 Thursday, March 19, 2015 10:34 AM
Safety information
1
Avoid Carbon Monoxide Poisoning
All engine exhaust contains carbon
monoxide, a deadly gas. Breathing
carbon monoxide can cause headaches, dizziness, drowsiness, nausea,
confusion, and eventually death.
Carbon Monoxide is a colorless, odorless, tasteless gas which may be
present even if you do not see or smell
any engine exhaust. Deadly levels of
carbon monoxide can collect rapidly
and you can quickly be overcome and
unable to save yourself. Also, deadly
levels of carbon monoxide can linger
for hours or days in enclosed or poorly
ventilated areas. If you experience any
symptoms of carbon monoxide poisoning, leave the area immediately, get
fresh air, and SEEK MEDICAL TREATMENT.
 Do not run engine indoors. Even if
you try to ventilate engine exhaust
with fans or open windows and
doors, carbon monoxide can rapidly reach dangerous levels.
 Do not run engine in poorly ventilated or partially enclosed areas
such as barns, garages, or carports.
 Do not run engine outdoors where
engine exhaust can be drawn into
a building through openings such
as windows and doors.
Loading
Adding accessories or cargo to your
scooter can adversely affect stability
and handling if the weight distribution
of the scooter is changed. To avoid the
possibility of an accident, use extreme
caution when adding cargo or accessories to your scooter. Use extra care
when riding a scooter that has added
cargo or accessories. Here, along with
the information about accessories below, are some general guidelines to follow if loading cargo to your scooter:
The total weight of the operator, passenger, accessories and cargo must
not exceed the maximum load limit.
Operation of an overloaded vehicle
could cause an accident.
Maximum load:
168 kg (370 lb)
When loading within this weight limit,
keep the following in mind:
1-3
 Cargo and accessory weight
should be kept as low and close to
the scooter as possible. Securely
pack your heaviest items as close
to the center of the vehicle as possible and make sure to distribute
the weight as evenly as possible
on both sides of the scooter to
minimize imbalance or instability.
 Shifting weights can create a sudden imbalance. Make sure that
accessories and cargo are securely attached to the scooter before riding. Check accessory
mounts and cargo restraints frequently.
• Properly adjust the suspension
for your load (suspension-adjustable models only), and
check the condition and pressure of your tires.
• Never attach any large or heavy
items to the handlebar, front
fork, or front fender. Such items
can create unstable handling or
a slow steering response.
 This vehicle is not designed to
pull a trailer or to be attached to
a sidecar.
U2DSE0E0.book Page 4 Thursday, March 19, 2015 10:34 AM
Safety information
Genuine Yamaha Accessories
Choosing accessories for your vehicle
is an important decision. Genuine
Yamaha accessories, which are available only from a Yamaha dealer, have
been designed, tested, and approved
by Yamaha for use on your vehicle.
Many companies with no connection
to Yamaha manufacture parts and accessories or offer other modifications
for Yamaha vehicles. Yamaha is not in
a position to test the products that
these aftermarket companies produce.
Therefore, Yamaha can neither endorse nor recommend the use of accessories not sold by Yamaha or
modifications not specifically recommended by Yamaha, even if sold and
installed by a Yamaha dealer.
Aftermarket Parts, Accessories, and
Modifications
While you may find aftermarket products similar in design and quality to
genuine Yamaha accessories, recognize that some aftermarket accessories or modifications are not suitable
because of potential safety hazards to
you or others. Installing aftermarket
products or having other modifications
performed to your vehicle that change
any of the vehicle’s design or operation
characteristics can put you and others
at greater risk of serious injury or
death. You are responsible for injuries
related to changes in the vehicle.
Keep the following guidelines in mind,
as well as those provided under “Loading” when mounting accessories.
 Never install accessories or carry
cargo that would impair the performance of your scooter. Carefully inspect the accessory before
using it to make sure that it does
not in any way reduce ground
clearance or cornering clearance,
limit suspension travel, steering
travel or control operation, or obscure lights or reflectors.
• Accessories fitted to the handlebar or the front fork area can
create instability due to improper weight distribution or aerodynamic changes. If accessories
are added to the handlebar or
front fork area, they must be as
lightweight as possible and
should be kept to a minimum.
1-4
• Bulky or large accessories may
seriously affect the stability of
the scooter due to aerodynamic
effects. Wind may attempt to lift
the scooter, or the scooter may
become unstable in cross
winds. These accessories may
also cause instability when
passing or being passed by
large vehicles.
• Certain accessories can displace the operator from his or
her normal riding position. This
improper position limits the
freedom of movement of the
operator and may limit control
ability, therefore, such accessories are not recommended.
 Use caution when adding electrical accessories. If electrical accessories exceed the capacity of
the scooter’s electrical system, an
electric failure could result, which
could cause a dangerous loss of
lights or engine power.
1
U2DSE0E0.book Page 5 Thursday, March 19, 2015 10:34 AM
Safety information
1
Aftermarket Tires and Rims
The tires and rims that came with your
scooter were designed to match the
performance capabilities and to provide the best combination of handling,
braking, and comfort. Other tires, rims,
sizes, and combinations may not be
appropriate. Refer to page 6-19 for tire
specifications and more information on
replacing your tires.
cation for the straps carefully so
the straps will not rub against
painted surfaces during transport.
 The suspension should be compressed somewhat by the tiedowns, if possible, so that the
scooter will not bounce excessively during transport.
Transporting the Scooter
Be sure to observe following instructions before transporting the scooter in
another vehicle.
 Remove all loose items from the
scooter.
 Point the front wheel straight
ahead on the trailer or in the truck
bed, and choke it in a rail to prevent movement.
 Secure the scooter with tie-downs
or suitable straps that are attached to solid parts of the scooter, such as the frame or upper
front fork triple clamp (and not, for
example, to rubber-mounted handlebars or turn signals, or parts
that could break). Choose the lo1-5
EAU57600
Further safe-riding points
 Be sure to signal clearly when
making turns.
 Braking can be extremely difficult
on a wet road. Avoid hard braking,
because the scooter could slide.
Apply the brakes slowly when
stopping on a wet surface.
 Slow down as you approach a
corner or turn. Once you have
completed a turn, accelerate
slowly.
 Be careful when passing parked
cars. A driver might not see you
and open a door in your path.
 Railroad crossings, streetcar rails,
iron plates on road construction
sites, and manhole covers become extremely slippery when
wet. Slow down and cross them
with caution. Keep the scooter upright, otherwise it could slide out
from under you.
 The brake pads or linings could
get wet when you wash the scooter. After washing the scooter,
check the brakes before riding.
U2DSE0E0.book Page 6 Thursday, March 19, 2015 10:34 AM
Safety information
 Always wear a helmet, gloves,
trousers (tapered around the cuff
and ankle so they do not flap), and
a brightly colored jacket.
 Do not carry too much luggage on
the scooter. An overloaded scooter is unstable. Use a strong cord
to secure any luggage to the carrier (if equipped). A loose load will
affect the stability of the scooter
and could divert your attention
from the road. (See page 1-3.)
1
1-6
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Description
EAU10411
Left view
1
2
2
3
4
11 10 8,9
1.
2.
3.
4.
5.
6.
7.
8.
Front storage compartment (page 3-16)
Fuel tank cap (page 3-12)
Owner’s tool kit (page 6-1)
Rear storage compartment (page 3-16)
Air filter element (page 6-16)
Final transmission oil filler cap (page 6-12)
Final transmission oil drain bolt (page 6-12)
Engine oil drain bolt A (page 6-10)
5
7
6
9. Engine oil drain bolt B (page 6-10)
10.Coolant drain bolt (page 6-14)
11.V-belt case air filter element (page 6-16)
2-1
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Description
EAU10421
Right view
1
2,3
9
1.
2.
3.
4.
5.
6.
7.
8.
8
7
6
5
Tail/brake light (page 6-32)
Battery (page 6-28)
Fuse box (page 6-29)
Headlight (page 6-30)
Coolant reservoir (page 6-13)
Spark plug (page 6-8)
Coolant drain screw (page 6-14)
Engine oil filler cap (page 6-10)
9. Radiator cap (page 6-13)
2-2
4
2
U2DSE0E0.book Page 3 Thursday, March 19, 2015 10:34 AM
Description
EAU10431
Controls and instruments
1
2
2
3
4
5
6
7
8
9
1.
2.
3.
4.
5.
6.
7.
8.
Rear brake lever (page 3-11)
Left handlebar switches (page 3-10)
Rear brake fluid reservoir (page 6-22)
Multi-function meter unit (page 3-4)
Front brake fluid reservoir (page 6-22)
Start switch (page 3-10)
Front brake lever (page 3-10)
Throttle grip (page 6-18)
9. Main switch/steering lock (page 3-1)
2-3
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
EAUN0263
Main switch/steering lock
OFF
ON
LOCK
The main switch/steering lock controls
the ignition and lighting systems, and is
used to lock the steering. The various
main switch positions are described
below.
TIP
The main switch/steering lock is
equipped with a keyhole shutter. (See
page 3-2 for keyhole shutter opening
and closing procedures.)
EAU60600
EAU10685
ON
All electrical circuits are supplied with
power; the meter lighting, taillight and
auxiliary lights come on, and the engine can be started. The key cannot be
removed.
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
TIP
The headlight comes on automatically
when the engine is started and stays
on until the key is turned to “OFF”,
even if the engine stalls.
3
To lock the steering
1
2
EAU10662
OFF
All electrical systems are off. The key
can be removed.
EWA10062
WARNING
Never turn the key to “OFF” or
“LOCK” while the vehicle is moving.
Otherwise the electrical systems will
be switched off, which may result in
loss of control or an accident.
3-1
1. Push.
2. Turn.
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF”
position, and then turn it to
“LOCK” while still pushing it.
3. Remove the key.
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
To unlock the steering
1
EAUN0352
Keyhole shutter
2
1
EAU49398
Indicator lights and warning
lights
2
3
1. Push.
2. Turn.
Push the key in, and then turn it to
“OFF” while still pushing it.
1. “PUSH SHUT” button
2. Key head
To open the keyhole shutter
Insert the key head into the keyhole
shutter receptacle as shown, and then
turn the key to the right to open the
keyhole shutter.
6
1
5
4
2
3
1.
2.
3.
4.
Right turn signal indicator light “ ”
High beam indicator light “
”
Coolant temperature warning light “ ”
Anti-lock Brake System (ABS) warning
light “ ABS ”
5. Engine trouble warning light “
”
6. Left turn signal indicator light “ ”
EAU11032
To close the keyhole shutter
Press the “PUSH SHUT” button to
close the keyhole shutter.
3-2
Turn signal indicator lights “ ”
and “ ”
Each indicator light will flash when its
corresponding turn signal lights are
flashing.
U2DSE0E0.book Page 3 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
EAU11081
High beam indicator light “ ”
This indicator light comes on when the
high beam of the headlight is switched
on.
EAUU1810
TIP
If the engine overheats, see page 6-38
for further instructions.
EAU42775
EAU67440
Coolant temperature warning
light “ ”
This warning light comes on if the engine overheats. If this occurs, stop the
engine immediately and allow the engine to cool.
The electrical circuit of the warning
light can be checked by turning the key
to “ON”. The warning light should
come on for a few seconds, and then
go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.
ECA10022
NOTICE
Engine trouble warning light “ ”
This warning light comes on if a problem is detected in the electrical circuit
monitoring the engine. If this occurs,
have a Yamaha dealer check the selfdiagnosis system. (See page 3-9 for an
explanation of the self-diagnosis device.)
The electrical circuit of the warning
light can be checked by turning the key
to “ON”. The warning light should
come on for a few seconds, and then
go off.
If the warning light does not come on
initially when the key is turned to “ON”,
or if the warning light remains on, have
a Yamaha dealer check the electrical
circuit.
Do not continue to operate the engine if it is overheating.
3-3
ABS warning light “ ”
In normal operation, the ABS warning
light comes on when the key is turned
to “ON”, and goes off after traveling at
a speed of 10 km/h (6 mi/h) or higher.
If the ABS warning light:
 does not come on when the key is
turned to “ON”
 comes on or flashes while riding
 does not go off after traveling at a
speed of 10 km/h (6 mi/h) or higher
The ABS may not work correctly. If any
of the above occurs, have a Yamaha
dealer check the system as soon as
possible. (See page 3-11 for an explanation of the ABS.)
ABS
EWA16041
WARNING
If the ABS warning light does not go
off after traveling at a speed of 10
km/h (6 mi/h) or higher, or if the
warning light comes on or flashes
while riding, the brake system reverts to conventional braking. If either of the above occurs, or if the
warning light does not come on at
all, use extra caution to avoid possi-
3
U2DSE0E0.book Page 4 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
ble wheel lock during emergency
braking. Have a Yamaha dealer
check the brake system and electrical circuits as soon as possible.
3
EAUN0981
Multi-function meter unit
1
2 3
4
TIP
The ABS warning light may come on
while accelerating the engine with the
vehicle on its centerstand, but this
does not indicate a malfunction.
7
1.
2.
3.
4.
5.
6.
7.
6
5
EWA12423
WARNING
Be sure to stop the vehicle before
making any setting changes to the
multi-function meter unit. Changing
settings while riding can distract the
operator and increase the risk of an
accident.
3-4
unit
a speedometer
a clock
a fuel meter
an instantaneous fuel consumption meter
 a multi-function display
TIP
 Be sure to turn the key to “ON” before using the “SELECT” and “RESET” buttons.
 For the UK: To switch the speedometer between km/h and MPH,
press the “SELECT” button for
one second when the multi-function meter is in odometer mode,
tripmeter 1, or tripmeter 2 mode .
Fuel meter
Clock
Speedometer
Instantaneous fuel consumption meter
“RESET” button
Multi-function display
“SELECT” button
The multi-function meter
equipped with the following:




is
Speedometer
The speedometer shows the vehicle’s
traveling speed.
U2DSE0E0.book Page 5 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
Clock
off for approximately 3 seconds. If this
occurs, have a Yamaha dealer check
the electrical circuit.
Fuel meter
1
1
2
Instantaneous
meter
fuel
consumption
3
1
1. Clock
The clock uses a 12-hour time system.
To set the clock
1. Turn the key to “ON”.
2. Push the “SELECT” button and
“RESET” button together for at
least two seconds.
3. When the hour digits start flashing, push the “RESET” button to
set the hours.
4. Push the “SELECT” button, and
the minute digits will start flashing.
5. Push the “RESET” button to set
the minutes.
6. Push the “SELECT” button and
then release it to start the clock.
1. Fuel meter
2. Fuel level warning indicator “
”
The fuel meter indicates the amount of
fuel in the fuel tank. The display segments of the fuel meter disappear towards “E” (Empty) as the fuel level
decreases. When the last segment and
fuel level warning indicator “ ” start
flashing, refuel as soon as possible.
TIP
This fuel meter is equipped with a selfdiagnosis system. If a problem is detected in the electrical circuit, the following cycle is repeated until the
malfunction is corrected: fuel level segments and fuel level warning
indicator “ ” flash eight times, then go
3-5
1. Instantaneous fuel consumption meter
This meter shows the instantaneous
fuel consumption.
Depending on the display setting selected for the instantaneous fuel consumption
mode
“F/ECO”,
the
displayed segments increase or decrease.
 km/L and MPG (for the UK): The
number of segments displayed increases the more efficiently the
vehicle is being operated.
U2DSE0E0.book Page 6 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
 L/100 km: The number of segments displayed decreases the
more efficiently the vehicle is being operated.
3
Multi-function display
1
1. Multi-function display
The multi-function display is equipped
with the following:
 an odometer
 two tripmeters (which show the
distance traveled since they were
last set to zero)
 a fuel reserve tripmeter (which
shows the distance traveled since
the last segment of the fuel meter
started flashing)
 an instantaneous fuel consumption display
 an average fuel consumption display
 an oil change tripmeter
 a V-belt replacement tripmeter
 an oil change indicator
 a V-belt replacement indicator
 an error code display
Except for the UK:
Push the “SELECT” button to switch
the display between the odometer
mode “ODO”, tripmeter modes “TRIP
1” and “TRIP 2”, oil change tripmeter
mode “OIL TRIP”, V-belt replacement
tripmeter mode “V-BELT TRIP”, instantaneous fuel consumption mode
“F/ECO” (km/L or L/100 km), and average fuel consumption mode “AVE
F/ECO” (km/L or L/100 km) in the following order:
ODO → TRIP 1 → TRIP 2 → OIL TRIP
→ V-BELT TRIP → F/ECO → AVE
F/ECO → ODO
For the UK:
Push the “SELECT” button to switch
the display between the odometer
mode “ODO”, tripmeter modes “TRIP
3-6
1” and “TRIP 2”, oil change tripmeter
mode “OIL TRIP”, V-belt replacement
tripmeter mode “V-BELT TRIP”, instantaneous fuel consumption mode
“F/ECO” (MPG or L/100 km), and average fuel consumption mode “AVE
F/ECO” (MPG or L/100 km) in the following order:
ODO → TRIP 1 → TRIP 2 → OIL TRIP
→ V-BELT TRIP → F/ECO → AVE
F/ECO → ODO
If the fuel level warning indicator “ ”
and last segment of the fuel meter start
flashing, the display automatically
changes to the fuel reserve tripmeter
mode “TRIP F” and starts counting the
distance traveled from that point. In
that case, push the “SELECT” button
to switch the display between the various tripmeter, odometer, oil change
tripmeter, V-belt replacement tripmeter, instantaneous fuel consumption
and average fuel consumption modes
in the following order:
U2DSE0E0.book Page 7 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
TRIP F → TRIP 1 → TRIP 2 → OIL TRIP
→ V-BELT TRIP → F/ECO → AVE
F/ECO → ODO → TRIP F
Instantaneous
mode
fuel
consumption
TIP
 If traveling at speeds under 10
km/h (6 mi/h), “_ _._” is displayed.
 When MPG is selected, no units
indicator will be displayed.
To reset a tripmeter, select it by pushing the “SELECT” button, and then
push the “RESET” button for at least
one second.
TIP
 If you do not reset the fuel reserve
tripmeter manually, it resets itself
automatically and the display returns to the prior mode after refueling and traveling 5 km (3 mi).
 If you do not reset tripmeters 1
and 2, they will reset to 0 and continue counting after 9999.9 has
been reached.
 The odometer will lock at 999999
and cannot be reset.
To switch between the instantaneous
fuel consumption display settings,
push the “SELECT” button for one second.
1
1. Instantaneous fuel consumption display
The instantaneous fuel consumption
display can be set to either “km/L” or
“L/100 km”, and either “MPG” or
“L/100 km” (for the UK).
 “km/L”: The distance that can be
traveled on 1.0 L of fuel under the
current riding conditions is shown.
 “L/100 km”: The amount of fuel
necessary to travel 100 km under
the current riding conditions is
shown.
 “MPG”: The distance that can be
traveled on 1.0 lmp. gal of the fuel
under the current riding conditions
is shown.
3-7
Average fuel consumption mode
1
1. Average fuel consumption display
This display shows the average fuel
consumption since it was last reset.
The average fuel consumption display
can be set to either “km/L” or “L/100
km”, and either “MPG” or “L/100 km”
(for the UK).
3
U2DSE0E0.book Page 8 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
3
 “km/L”: The average distance that
can be traveled on 1.0 L of fuel is
shown.
 “L/100 km”: The average amount
of fuel necessary to travel 100 km
is shown.
 “MPG”: The average distance that
can be traveled on 1.0 lmp. gal of
fuel under the current riding conditions is shown.
To switch between the average fuel
consumption display settings, push
the “SELECT” button for one second.
To reset the average fuel consumption,
push the “RESET” button for at least
one second.
TIP
 After resetting the average fuel
consumption, “_ _._” will be
shown until the vehicle has traveled 0.1 km (0.06 mi).
 When MPG is selected, no units
indicator will be displayed.
Oil change tripmeter mode
1
2
1. Oil change indicator “OIL”
2. Oil change tripmeter
The oil change tripmeter shows the
distance traveled since it was last reset
(i.e., since the last oil change).
The oil change indicator “OIL” will flash
at the initial 1000 km (600 mi), then at
6000 km (3500 mi) and every 6000 km
(3500 mi) thereafter to indicate that the
engine oil should be changed.
After changing the engine oil, reset the
oil change tripmeter and the oil change
indicator. To reset them both, select
the oil change tripmeter, and then push
the “RESET” button for one second.
Then, while “OIL” and the oil change
3-8
tripmeter are flashing, push the “RESET” button for three seconds. The oil
change indicator will be reset.
If the engine oil is changed before the
oil change indicator comes on (i.e., before the periodic oil change interval has
been reached), the oil change tripmeter
must be reset for the next periodic oil
change to be indicated at the correct
time.
V-belt replacement tripmeter mode
1
2
1. V-belt replacement indicator “V-BELT”
2. V-belt replacement tripmeter
The V-belt replacement tripmeter
shows the distance traveled since it
was last reset (i.e., since the last V-belt
replacement).
U2DSE0E0.book Page 9 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
The V-belt replacement indicator “VBELT” will flash at every 18000 km
(10500 mi) thereafter to indicate that
the V-belt should be replaced.
After replacing the V-belt, reset the Vbelt replacement tripmeter and the Vbelt replacement indicator. To reset
them both, select the V-belt replacement tripmeter, and then push the
“RESET” button for one second. Then,
while “V-BELT” and the V-belt replacement tripmeter are flashing, push the
“RESET” button for three seconds. The
V-belt replacement indicator will be reset.
If the V-belt is replaced before the Vbelt replacement indicator comes on
(i.e., before the periodic V-belt replacement interval has been reached), the Vbelt replacement tripmeter must be reset for the next periodic V-belt replacement to be indicated at the correct
time.
Self-diagnosis mode
ECA11591
NOTICE
1
If the display indicates an error
code, the vehicle should be checked
as soon as possible in order to avoid
engine damage.
2
1. Engine trouble warning light “
2. Error code display
”
This model is equipped with a self-diagnosis device for various electrical
circuits.
If a problem is detected in any of those
circuits, the engine trouble warning
light will come on and the display will
indicate an error code.
If the display indicates any error codes,
note the code number, and then have
a Yamaha dealer check the vehicle.
3-9
3
U2DSE0E0.book Page 10 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
EAU1234H
Handlebar switches
EAU12401
Dimmer switch “ / ”
Set this switch to “ ” for the high
beam and to “ ” for the low beam.
Left
EAU12902
Front brake lever
1
EAU12461
1
3
Turn signal switch “ / ”
To signal a right-hand turn, push this
switch to “ ”. To signal a left-hand
turn, push this switch to “ ”. When
released, the switch returns to the center position. To cancel the turn signal
lights, push the switch in after it has returned to the center position.
2
3
1. Dimmer switch “
/
”
2. Turn signal switch “ / ”
3. Horn switch “
”
EAU12501
Horn switch “
”
Press this switch to sound the horn.
Right
EAU12722
1
1. Start switch “
Start switch “ ”
With the sidestand up, push this switch
while applying the front or rear brake to
crank the engine with the starter. See
page 5-1 for starting instructions prior
to starting the engine.
”
3-10
1. Front brake lever
The front brake lever is located on the
right side of the handlebar. To apply
the front brake, pull this lever toward
the throttle grip.
U2DSE0E0.book Page 11 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
EAU12952
Rear brake lever
1
1. Rear brake lever
The rear brake lever is located on the
left side of the handlebar. To apply the
rear brake, pull this lever toward the
handlebar grip.
EAU66680
ABS
The Yamaha ABS (Anti-lock Brake
System) features a dual electronic control system, which acts on the front and
rear brakes independently.
Operate the brakes with ABS as you
would conventional brakes. If the ABS
is activated, a pulsating sensation may
be felt at the brake levers. In this situation, continue to apply the brakes and
let the ABS work; do not “pump” the
brakes as this will reduce braking effectiveness.
EWA16051
WARNING
Always keep a sufficient distance
from the vehicle ahead to match the
riding speed even with ABS.
 The ABS performs best with
long braking distances.
 On certain surfaces, such as
rough or gravel roads, the braking distance may be longer with
the ABS than without.
The ABS is monitored by an ECU,
which will revert the system to conventional braking if a malfunction occurs.
3-11
TIP
 The ABS performs a self-diagnosis test each time the vehicle first
starts off after the key is turned to
“ON” and the vehicle has traveled
at a speed of 10 km/h (6 mi/h) or
higher. During this test, a “clicking” noise can be heard from the
front of the vehicle, and if either
brake lever is even slightly applied, a vibration can be felt at the
lever, but these do not indicate a
malfunction.
 This ABS has a test mode which
allows the owner to experience
the pulsation at the brake levers
when the ABS is operating. However, special tools are required, so
please consult your Yamaha dealer.
ECA20100
NOTICE
Be careful not to damage the wheel
sensor or wheel sensor rotor; otherwise, improper performance of the
ABS will result.
3
U2DSE0E0.book Page 12 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
EAU66690
Fuel tank cap
1
2
3
1
1
2
3
1. Front wheel sensor
2. Front wheel sensor rotor
1. “
1
2
1. Rear wheel sensor
2. Rear wheel sensor rotor
1. Fuel tank cap lock cover
2. Lock.
3. Unlock.
To remove the fuel tank cap
Open the fuel tank cap lock cover, insert the key into the lock, and then turn
it 1/4 turn clockwise. The lock will be
released and the fuel tank cap can be
removed.
” mark
2. Turn the key counterclockwise to
the original position, remove it,
and then close the lock cover.
TIP
The fuel tank cap cannot be installed
unless the key is in the lock. In addition, the key cannot be removed if the
cap is not properly installed and
locked.
EWA10132
To install the fuel tank cap
1. Insert the fuel tank cap into the
tank opening with the key inserted
in the lock and with the “ ” mark
facing forward.
3-12
WARNING
Make sure that the fuel tank cap is
properly installed before riding.
Leaking fuel is a fire hazard.
U2DSE0E0.book Page 13 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
ately. If gasoline spills on your skin,
wash with soap and water. If gasoline spills on your clothing, change
your clothes.
EAU13213
Fuel
Make sure there is sufficient gasoline in
the tank.
2
1
EWA10882
WARNING
Gasoline and gasoline vapors are
extremely flammable. To avoid fires
and explosions and to reduce the
risk of injury when refueling, follow
these instructions.
1. Before refueling, turn off the engine and be sure that no one is sitting on the vehicle. Never refuel
while smoking, or while in the vicinity of sparks, open flames, or
other sources of ignition such as
the pilot lights of water heaters
and clothes dryers.
2. Do not overfill the fuel tank. Stop
filling when the fuel reaches the
bottom of the filler tube. Because
fuel expands when it heats up,
heat from the engine or the sun
can cause fuel to spill out of the
fuel tank.
EAU53013
Recommended fuel:
Regular unleaded gasoline (Gasohol
(E10) acceptable)
Fuel tank capacity:
6.6 L (1.74 US gal, 1.45 Imp.gal)
1. Fuel tank filler tube
2. Maximum fuel level
3. Wipe up any spilled fuel immediately. NOTICE: Immediately
wipe off spilled fuel with a clean,
dry, soft cloth, since fuel may
deteriorate painted surfaces or
plastic parts. [ECA10072]
4. Be sure to securely close the fuel
tank cap.
EWA15152
WARNING
Gasoline is poisonous and can
cause injury or death. Handle gasoline with care. Never siphon gasoline
by mouth. If you should swallow
some gasoline or inhale a lot of gasoline vapor, or get some gasoline in
your eyes, see your doctor immedi3-13
ECA11401
NOTICE
Use only unleaded gasoline. The use
of leaded gasoline will cause severe
damage to internal engine parts,
such as the valves and piston rings,
as well as to the exhaust system.
Your Yamaha engine has been designed to use regular unleaded gasoline with a research octane number of
95 or higher. If knocking (or pinging)
occurs, use a gasoline of a different
brand or premium unleaded fuel. Use
of unleaded fuel will extend spark plug
life and reduce maintenance costs.
3
U2DSE0E0.book Page 14 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
3
Gasohol
There are two types of gasohol: gasohol containing ethanol and that containing methanol. Gasohol containing
ethanol can be used if the ethanol content does not exceed 10% (E10). Gasohol containing methanol is not
recommended by Yamaha because it
can cause damage to the fuel system
or vehicle performance problems.
EAU58300
Fuel tank overflow hose
EAU13434
Catalytic converter
This model is equipped with a catalytic
converter in the exhaust system.
EWA10863
WARNING
1
1. Fuel tank overflow hose
Before operating the scooter:
 Check the fuel tank overflow hose
connection and routing.
 Check the fuel tank overflow hose
for cracks or damage, and replace
it if necessary.
 Make sure that the fuel tank overflow hose is not blocked, and
clean it if necessary.
3-14
The exhaust system is hot after operation. To prevent a fire hazard or
burns:
 Do not park the vehicle near
possible fire hazards such as
grass or other materials that
easily burn.
 Park the vehicle in a place
where pedestrians or children
are not likely to touch the hot
exhaust system.
 Make sure that the exhaust system has cooled down before
doing any maintenance work.
 Do not allow the engine to idle
more than a few minutes. Long
idling can cause a build-up of
heat.
U2DSE0E0.book Page 15 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
ECA10702
NOTICE
Use only unleaded gasoline. The use
of leaded gasoline will cause unrepairable damage to the catalytic
converter.
EAU60620
Seat
To open the seat
1. Place the vehicle on the centerstand.
2. Insert the key into the main switch,
and then turn it counterclockwise
to “SEAT OPEN”.
1
1. Open.
TIP
Do not push inward when turning the
key.
3. Fold the seat up.
To close the seat
1. Fold the seat down, and then push
it down to lock it in place.
3-15
2. Remove the key.
TIP
Make sure that the seat is properly secured before riding.
3
U2DSE0E0.book Page 16 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
EAU57081
Storage compartments
3
Front storage compartment
The front storage compartment is located at the front of the vehicle. Use
this compartment for small items.
1
Rear storage compartment
The rear storage compartment is located under the seat. Use this compartment for large items. (See page 3-15.)
1
1. Rear storage compartment
EWAT1052
WARNING
1. Front storage compartment
EWA17250
WARNING
 Do not exceed the load limit of
1.5 kg (3.3 lb) for the front storage compartment.
 Do not place anything in the
front storage compartment that
will interfere with your operating
the vehicle.
 Do not exceed the load limit of 5
kg (11 lb) for the rear storage
compartment.
 Do not exceed the maximum
load of 168 kg (370 lb) for the vehicle.
ECA21150
NOTICE
Keep the following points in mind
when using the storage compartment.
3-16
 Since the storage compartment
accumulates heat when exposed to the sun and/or the engine heat, do not store anything
susceptible to heat, consumables or flammable items inside
it.
 To avoid humidity from spreading through the storage compartment, wrap wet articles in a
plastic bag before storing them
in the compartment.
 Since the storage compartment
may get wet while the vehicle is
being washed, wrap any articles
stored in the compartment in a
plastic bag.
 Do not keep anything valuable
or breakable in the storage
compartment.
TIP
Do not leave your vehicle unattended
with the seat open.
U2DSE0E0.book Page 17 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
EAU15306
Sidestand
The sidestand is located on the left
side of the frame. Raise the sidestand
or lower it with your foot while holding
the vehicle upright.
this system regularly and have a
Yamaha dealer repair it if it does not
function properly.
EAUT1096
Ignition circuit cut-off system
Check the operation of the sidestand
switch according to the following procedure.
3
TIP
The built-in sidestand switch is part of
the ignition circuit cut-off system,
which cuts the ignition in certain situations. (See the following section for an
explanation of the ignition circuit cutoff system.)
EWA10242
WARNING
The vehicle must not be ridden with
the sidestand down, or if the sidestand cannot be properly moved up
(or does not stay up), otherwise the
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
Yamaha’s ignition circuit cut-off
system has been designed to assist
the operator in fulfilling the responsibility of raising the sidestand before starting off. Therefore, check
3-17
U2DSE0E0.book Page 18 Thursday, March 19, 2015 10:34 AM
Instrument and control functions
3
Turn the key on.
WARNING
• The vehicle must be placed on the centerPut the sidestand up.
stand during this inspection.
• If a malfunction is noted, have a Yamaha
dealer check the system before riding.
Push the start switch while applying
either of the brake levers. The engine will
start.
Put the sidestand down.
If the engine stalls:
The sidestand switch is OK.
3-18
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
For your safety – pre-operation checks
EAU15599
Inspect your vehicle each time you use it to make sure the vehicle is in safe operating condition. Always follow the inspection
and maintenance procedures and schedules described in the Owner’s Manual.
EWA11152
WARNING
Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage.
Do not operate the vehicle if you find any problem. If a problem cannot be corrected by the procedures provided in
this manual, have the vehicle inspected by a Yamaha dealer.
Before using this vehicle, check the following points:
ITEM
CHECKS
PAGE
Fuel
• Check fuel level in fuel tank.
• Refuel if necessary.
• Check fuel line for leakage.
• Check fuel tank overflow hose for obstructions, cracks or damage, and check
hose connection.
Engine oil
• Check oil level in engine.
• If necessary, add recommended oil to specified level.
• Check vehicle for oil leakage.
6-10
Final transmission oil
• Check vehicle for oil leakage.
6-12
Coolant
• Check coolant level in reservoir.
• If necessary, add recommended coolant to specified level.
• Check cooling system for leakage.
6-13
Front brake
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add specified brake fluid to specified level.
• Check hydraulic system for leakage.
4-1
3-13, 3-14
6-21, 6-22, 6-22
4
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
For your safety – pre-operation checks
ITEM
CHECKS
PAGE
Rear brake
• Check operation.
• If soft or spongy, have Yamaha dealer bleed hydraulic system.
• Check brake pads for wear.
• Replace if necessary.
• Check fluid level in reservoir.
• If necessary, add specified brake fluid to specified level.
• Check hydraulic system for leakage.
Throttle grip
• Make sure that operation is smooth.
• Check throttle grip free play.
• If necessary, have Yamaha dealer adjust throttle grip free play and lubricate cable and grip housing.
Control cables
• Make sure that operation is smooth.
• Lubricate if necessary.
6-24
Wheels and tires
• Check for damage.
• Check tire condition and tread depth.
• Check air pressure.
• Correct if necessary.
6-19, 6-21
Brake levers
• Make sure that operation is smooth.
• Lubricate lever pivoting points if necessary.
6-25
Centerstand, sidestand
• Make sure that operation is smooth.
• Lubricate pivots if necessary.
6-26
Chassis fasteners
• Make sure that all nuts, bolts and screws are properly tightened.
• Tighten if necessary.
—
Instruments, lights, signals
and switches
• Check operation.
• Correct if necessary.
—
Sidestand switch
• Check operation of ignition circuit cut-off system.
• If system is not working correctly, have Yamaha dealer check vehicle.
4
4-2
6-21, 6-22, 6-22
6-18, 6-25
3-17
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Operation and important riding points
EAU15952
EAU66720
Starting the engine
Read the Owner’s Manual carefully to
become familiar with all controls. If
there is a control or function you do not
understand, ask your Yamaha dealer.
EWA10272
WARNING
Failure to familiarize yourself with
the controls can lead to loss of control, which could cause an accident
or injury.
ECA10251
NOTICE
See page 5-3 for engine break-in instructions prior to operating the vehicle for the first time.
In order for the ignition circuit cut-off
system to enable starting, the sidestand must be up.
See page 3-17 for more information.
1. Turn the key to “ON”.
The following warning lights
should come on for a few seconds, then go off.
 Engine trouble warning light
 Coolant temperature warning
light
ECA15485
NOTICE
If a warning light does not come on
initially when the key is turned to
“ON”, or if a warning light remains
on, see page 3-2 for the corresponding warning light circuit check.
The ABS warning light should
come on when the main switch is
turned to “ON” and then go off after traveling at a speed of 10 km/h
(6 mi/h) or higher.
ECA17682
NOTICE
If the ABS warning light does not
come on and then go off as explained above, see page 3-2 for the
warning light circuit check.
2. Close the throttle completely.
3. Start the engine by pushing the
start switch while applying the
front or rear brake.
If the engine does not start, release the start switch, wait a few
seconds, and then try again. Each
starting attempt should be as
short as possible to preserve the
battery. Do not crank the engine
more than 10 seconds on any one
attempt.
ECA11043
NOTICE
For maximum engine life, never accelerate hard when the engine is
cold!
5-1
5
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Operation and important riding points
EAU45093
Starting off
EAU16782
Acceleration and deceleration
1. While pulling the rear brake lever
with your left hand and holding the
grab bar with your right hand,
push the scooter off the centerstand.
EWA10301
WARNING
(b)
1
5
(a)
ZAUM0199
1. Grab bar
EAU16794
Braking
The speed can be adjusted by opening
and closing the throttle. To increase
the speed, turn the throttle grip in direction (a). To reduce the speed, turn
the throttle grip in direction (b).
2. Sit astride the seat, and then adjust the rear view mirrors.
3. Switch the turn signals on.
4. Check for oncoming traffic, and
then slowly turn the throttle grip
(on the right) in order to take off.
5. Switch the turn signals off.
 Avoid braking hard or suddenly
(especially when leaning over to
one side), otherwise the scooter
may skid or overturn.
 Railroad crossings, streetcar
rails, iron plates on road construction sites, and manhole
covers become extremely slippery when wet. Therefore, slow
down when approaching such
areas and cross them with caution.
 Keep in mind that braking on a
wet road is much more difficult.
 Ride slowly down a hill, as braking downhill can be very difficult.
1. Close the throttle completely.
2. Apply both front and rear brakes
simultaneously while gradually increasing the pressure.
5-2
U2DSE0E0.book Page 3 Thursday, March 19, 2015 10:34 AM
Operation and important riding points
EAU16821
Tips for reducing fuel consumption
Fuel consumption depends largely on
your riding style. Consider the following tips to reduce fuel consumption:
 Avoid high engine speeds during
acceleration.
 Avoid high engine speeds with no
load on the engine.
 Turn the engine off instead of letting it idle for an extended length
of time (e.g., in traffic jams, at traffic lights or at railroad crossings).
EAU16842
Engine break-in
There is never a more important period
in the life of your engine than the period
between 0 and 1600 km (1000 mi). For
this reason, you should read the following material carefully.
Since the engine is brand new, do not
put an excessive load on it for the first
1600 km (1000 mi). The various parts in
the engine wear and polish themselves
to the correct operating clearances.
During this period, prolonged full-throttle operation or any condition that
might result in engine overheating
must be avoided.
EAUM2012
0–1000 km (0–600 mi)
Avoid prolonged operation above 1/3
throttle. NOTICE: After 1000 km (600
mi) of operation, be sure to replace
the engine oil and final transmission
oil. [ECA11662]
1000–1600 km (600–1000 mi)
Avoid prolonged operation above 1/2
throttle.
5-3
1600 km (1000 mi) and beyond
The vehicle can now be operated normally.
ECA10271
NOTICE
If any engine trouble should occur
during the engine break-in period,
immediately have a Yamaha dealer
check the vehicle.
5
U2DSE0E0.book Page 4 Thursday, March 19, 2015 10:34 AM
Operation and important riding points
EAU17214
Parking
When parking, stop the engine, and
then remove the key from the main
switch.
EWA10312
WARNING
5
 Since the engine and exhaust
system can become very hot,
park in a place where pedestrians or children are not likely to
touch them and be burned.
 Do not park on a slope or on soft
ground, otherwise the vehicle
may overturn, increasing the
risk of a fuel leak and fire.
 Do not park near grass or other
flammable materials which
might catch fire.
5-4
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU17246
EWA15123
Periodic inspection, adjustment, and
lubrication will keep your vehicle in the
safest and most efficient condition
possible. Safety is an obligation of the
vehicle owner/operator. The most important points of vehicle inspection,
adjustment, and lubrication are explained on the following pages.
The intervals given in the periodic
maintenance charts should be simply
considered as a general guide under
normal riding conditions. However, depending on the weather, terrain, geographical location, and individual use,
the maintenance intervals may need to
be shortened.
Turn off the engine when performing
maintenance
unless
otherwise
specified.
 A running engine has moving
parts that can catch on body
parts or clothing and electrical
parts that can cause shocks or
fires.
 Running the engine while servicing can lead to eye injury,
burns, fire, or carbon monoxide
poisoning – possibly leading to
death. See page 1-3 for more information about carbon monoxide.
EWA15461
EWA10322
WARNING
Failure to properly maintain the vehicle or performing maintenance activities incorrectly may increase
your risk of injury or death during
service or while using the vehicle. If
you are not familiar with vehicle service, have a Yamaha dealer perform
service.
EAU39692
Owner’s tool kit
WARNING
WARNING
Brake discs, calipers, drums, and
linings can become very hot during
use. To avoid possible burns, let
brake components cool before
touching them.
6-1
1
1. Owner’s tool kit
The owner’s tool kit is located on the
bottom of the seat. (See page 3-15.)
The service information included in this
manual and the tools provided in the
owner’s tool kit are intended to assist
you in the performance of preventive
maintenance and minor repairs. However, additional tools such as a torque
wrench may be necessary to perform
certain maintenance work correctly.
TIP
If you do not have the tools or experience required for a particular job, have
a Yamaha dealer perform it for you.
6
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU46872
TIP
 The annual checks must be performed every year, except if a kilometer-based maintenance, or for the UK, a
mileage-based maintenance, is performed instead.
 From 30000 km (17500 mi), repeat the maintenance intervals starting from 6000 km (3500 mi).
 Items marked with an asterisk should be performed by a Yamaha dealer as they require special tools, data and technical skills.
EAU46921
Periodic maintenance chart for the emission control system
ODOMETER READING
6
NO.
ITEM
1 * Fuel line
2
Spark plug
CHECK OR MAINTENANCE JOB
1000 km
(600 mi)
6000 km
(3500 mi)
12000 km
(7000 mi)
18000 km
(10500 mi)
24000 km
(14000 mi)
• Check fuel hoses for cracks or
damage.
√
√
√
√
• Check condition.
• Clean and regap.
√
√
3 * Valves
• Check valve clearance.
• Adjust.
√
√
√
√
4 * Fuel injection
• Check engine idle speed.
√
√
√
√
6-2
√
√
√
• Replace.
ANNUAL
CHECK
√
U2DSE0E0.book Page 3 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU1771A
General maintenance and lubrication chart
ODOMETER READING
NO.
ITEM
CHECK OR MAINTENANCE JOB
1
Air filter element
• Replace.
2
Air filter check hose
• Clean.
3 *
V-belt case air filter
element
• Clean.
• Replace if necessary.
4 * Front brake
• Check operation, fluid level and
vehicle for fluid leakage.
6000 km
(3500 mi)
12000 km
(7000 mi)
√
√
√
5 * Rear brake
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
√
Whenever worn to the limit
√
√
• Replace brake pads.
6 * Brake hoses
24000 km
(14000 mi)
√
• Replace brake pads.
• Check operation, fluid level and
vehicle for fluid leakage.
18000 km
(10500 mi)
ANNUAL
CHECK
1000 km
(600 mi)
√
√
Whenever worn to the limit
• Check for cracks or damage.
• Check for correct routing and
clamping.
√
• Replace.
√
√
Every 4 years
7 * Brake fluid
• Change.
8 * Wheels
• Check runout and for damage.
√
√
Every 2 years
√
√
9 * Tires
• Check tread depth and for damage.
• Replace if necessary.
• Check air pressure.
• Correct if necessary.
√
√
√
√
10 * Wheel bearings
• Check bearings for looseness or
damage.
√
√
√
√
6-3
√
6
U2DSE0E0.book Page 4 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
ODOMETER READING
NO.
ITEM
11 * Steering bearings
12 * Chassis fasteners
CHECK OR MAINTENANCE JOB
• Check bearing play and steering
for roughness.
1000 km
(600 mi)
6000 km
(3500 mi)
12000 km
(7000 mi)
18000 km
(10500 mi)
24000 km
(14000 mi)
√
√
√
√
√
• Lubricate with lithium-soapbased grease.
ANNUAL
CHECK
Every 24000 km (14000 mi)
• Make sure that all nuts, bolts and
screws are properly tightened.
√
√
√
√
√
13
Front brake lever
pivot shaft
• Lubricate with silicone grease.
√
√
√
√
√
14
Rear brake lever
pivot shaft
• Lubricate with silicone grease.
√
√
√
√
√
15
Sidestand, centerstand
• Check operation.
• Lubricate with lithium-soapbased grease.
√
√
√
√
√
√
6
16 * Sidestand switch
• Check operation.
√
√
√
√
17 * Front fork
• Check operation and for oil leakage.
√
√
√
√
• Check operation and shock absorbers for oil leakage.
√
√
√
√
18 *
Shock absorber assemblies
• Change. (See page 6-10.)
19
√
√
Engine oil
• Check oil level and vehicle for oil
leakage.
20 * Engine oil strainer
• Clean.
When the oil change indicator light flashes (5000 km (3000 mi) after the initial 1000 km [600 mi] and every 6000 km (3500 mi)
thereafter)
Every 6000 km (3500 mi)
√
6-4
√
U2DSE0E0.book Page 5 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
ODOMETER READING
NO.
ITEM
21 * Cooling system
CHECK OR MAINTENANCE JOB
1000 km
(600 mi)
• Check coolant level and vehicle
for coolant leakage.
6000 km
(3500 mi)
12000 km
(7000 mi)
18000 km
(10500 mi)
24000 km
(14000 mi)
√
√
√
√
• Change coolant.
22
Final transmission
oil
23 * V-belt
• Check vehicle for oil leakage.
• Change.
• Replace.
24 *
Front and rear
brake switches
• Check operation.
25
Moving parts and
cables
26 * Throttle grip
27 *
Lights, signals and
switches
ANNUAL
CHECK
√
Every 3 years
√
√
√
√
√
√
When the V-belt replacement indicator flashes [every 18000 km (10500 mi)]
√
√
√
√
√
• Lubricate.
√
√
√
√
√
• Check operation.
• Check throttle grip free play, and
adjust if necessary.
• Lubricate cable and grip housing.
√
√
√
√
√
√
√
√
√
√
• Check operation.
• Adjust headlight beam.
√
√
EAUN0990
TIP
 Engine air filter and V-belt air filter
• This model’s engine air filter is equipped with a disposable oil-coated paper element, which must not be cleaned
with compressed air to avoid damaging it.
• The engine air filter element needs to be replaced and the V-belt air filter element needs to be serviced more frequently when riding in unusually wet or dusty areas.
6-5
6
U2DSE0E0.book Page 6 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
 Hydraulic brake service
• After disassembling the brake master cylinders and calipers, always change the fluid. Regularly check the brake fluid
levels and fill the reservoirs as required.
• Every two years replace the internal components of the brake master cylinders and calipers, and change the brake
fluid.
• Replace the brake hoses every four years and if cracked or damaged.
6
6-6
U2DSE0E0.book Page 7 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
2. Retract the right passenger footrest to its original position.
EAU18773
Removing and installing panels
2
The panels shown need to be removed
to perform some of the maintenance
jobs described in this chapter. Refer to
this section each time a panel needs to
be removed and installed.
1
2
To remove the panel
1. Remove panel A.
2. Remove the quick fasteners and
the bolt.
1. Panel A
2. Bolt
1
Panel B
1
2. Extend the right passenger footrest, and then pull the panel outward.
To install the panel
1. Place the panel in the original position, and then install the bolts.
2
1. Panel A
2. Panel B
EAU67270
Panel A
To remove the panel
1. Remove the bolts.
6-7
6
2
1. Panel B
2. Quick fastener
U2DSE0E0.book Page 8 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU67161
Checking the spark plug
1
1
2
1. Bolt
2. Quick fastener
6
1. Bolt
3. Remove the right floorboard mats
by pulling them up.
To install the panel
1. Place the panel in the original position, and then install the bolts.
2. Place the right floorboard mats in
their original position and push
them downward to secure them.
3. Install the bolt and the quick fasteners.
4. Install panel A.
The spark plug is an important engine
component, which is easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plug should be removed and checked
in accordance with the periodic maintenance and lubrication chart. In addition, the condition of the spark plug
can reveal the condition of the engine.
To remove the spark plug
1. Place the vehicle on the centerstand.
2. Remove panels A and B. (See
page 6-7.)
3. Remove the spark plug cap.
1
1. Floorboard mat
4. Remove the bolts, and then pull
the panel outward.
1
1. Spark plug cap
6-8
U2DSE0E0.book Page 9 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
4. Remove the spark plug as shown,
with the spark plug wrench included in the owner’s tool kit.
2. Check the spark plug for electrode
erosion and excessive carbon or
other deposits, and replace it if
necessary.
Specified spark plug:
NGK/CPR8EA-9
1
3. Measure the spark plug gap with a
wire thickness gauge and, if necessary, adjust the gap to specification.
1. Spark plug wrench
Tightening torque:
Spark plug:
13 Nm (1.3 m·kgf, 9.4 ft·lbf)
TIP
If a torque wrench is not available
when installing a spark plug, a good
estimate of the correct torque is 1/4–
1/2 turn past finger tight. However, the
spark plug should be tightened to the
specified torque as soon as possible.
To check the spark plug
1. Check that the porcelain insulator
around the center electrode of the
spark plug is a medium-to-light
tan (the ideal color when the vehicle is ridden normally).
TIP
If the spark plug shows a distinctly different color, the engine could be operating improperly. Do not attempt to
diagnose such problems yourself. Instead, have a Yamaha dealer check
the vehicle.
To install the spark plug
1. Clean the surface of the spark
plug gasket and its mating surface, and then wipe off any grime
from the spark plug threads.
2. Install the spark plug with the
spark plug wrench, and then tighten it to the specified torque.
3. Install the spark plug cap.
1. Spark plug gap
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
6-9
TIP
Install the spark plug cap so that it is
positioned as shown in the illustration
and the spark plug lead does not contact any surrounding parts.
6
U2DSE0E0.book Page 10 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU66991
Engine oil and oil strainer
2
1
1. Spark plug cap
2. Spark plug lead
6
4. Install the panels.
The engine oil level should be checked
before each ride. In addition, the oil
must be changed and the oil strainer
cleaned at the intervals specified in the
periodic maintenance and lubrication
chart.
To check the engine oil level
1. Place the vehicle on the centerstand. A slight tilt to the side can
result in a false reading.
2. Start the engine, warm it up for
several minutes, and then turn it
off.
3. Wait a few minutes until the oil settles, remove the engine oil filler
cap, wipe the engine oil dipstick
clean, insert it back into the oil filler hole (without screwing it in), and
then remove it again to check the
oil level. WARNING! The muffler
and muffler protector become
very hot during use. To avoid
possible burns, let the muffler
and protector cool before removing the oil filler cap. [EWA17810]
6-10
TIP
The engine oil should be between the
tip of the dipstick and the maximum
level mark.
2
1
3
4
1.
2.
3.
4.
Engine oil filler cap
Engine oil dipstick
Maximum level mark
Tip of the engine oil dipstick
4. If the engine oil is not between the
tip of the dipstick and the maximum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.
U2DSE0E0.book Page 11 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for
several minutes, and then turn it
off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap
and engine oil drain bolts A and B
to drain the oil from the crankcase.
NOTICE: When removing the
engine oil drain bolt B, the Oring, compression spring, and
oil strainer will fall out. Take
care not to lose these parts.
[ECAT1022]
6. Install engine oil drain bolt A and
its new gasket, and then tighten
both drain bolts to their specified
torques.
3
4
5
2
1
6
1.
2.
3.
4.
5.
6.
Engine oil drain bolt A
Gasket
Oil strainer
Compression spring
O-ring
Engine oil drain bolt B
4. Clean the engine oil strainer with
solvent, and then check it for
damage and replace it if necessary.
5. Install the engine oil strainer, compression spring, new O-ring and
engine oil drain bolt B.
TIP
Make sure that the O-ring is properly
seated.
Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m·kgf, 14 ft·lbf)
Engine oil drain bolt B:
32 Nm (3.2 m·kgf, 23 ft·lbf)
7. Refill with the specified amount of
the recommended engine oil, and
then install and tighten the oil filler
cap.
Recommended engine oil:
See page 8-1.
Oil quantity:
0.90 L (0.95 US qt, 0.79 Imp.qt)
TIP
Be sure to wipe off spilled oil on any
parts after the engine and exhaust system have cooled down.
ECA11621
NOTICE
 In order to prevent clutch slippage (since the engine oil also
lubricates the clutch), do not
6-11
6
U2DSE0E0.book Page 12 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
mix any chemical additives. Do
not use oils with a diesel specification of “CD” or oils of a higher quality than specified. In
addition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
 Make sure that no foreign material enters the crankcase.
6
8. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off
and check for the cause.
9. Turn the engine off, and then
check the oil level and correct it if
necessary.
10. Reset the oil change tripmeter and
oil change indicator “OIL”. (See
page 3-6 for reset procedures.)
EAU20067
Final transmission oil
The final transmission case must be
checked for oil leakage before each
ride. If any leakage is found, have a
Yamaha dealer check and repair the
scooter. In addition, the final transmission oil must be changed as follows at
the intervals specified in the periodic
maintenance and lubrication chart.
1. Start the engine, warm up the final
transmission oil by riding the
scooter for several minutes, and
then stop the engine.
2. Place the scooter on the centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the final transmission oil
filler cap and its O-ring from the final transmission case.
1
2
1. Final transmission oil filler cap
2. O-ring
5. Remove the final transmission oil
drain bolt and its gasket to drain
the oil from the final transmission
case.
2
1. Final transmission oil drain bolt
2. Gasket
6-12
1
U2DSE0E0.book Page 13 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
6. Install the final transmission oil
drain bolt and its new gasket, and
then tighten the bolt to the specified torque.
Tightening torque:
Final transmission oil drain bolt:
20 Nm (2.0 m·kgf, 14 ft·lbf)
EAU20071
Coolant
The coolant level should be checked
before each ride. In addition, the coolant must be changed at the intervals
specified in the periodic maintenance
and lubrication chart.
2
3
1
EAUN1090
7. Refill with the specified amount of
the recommended final transmission oil. WARNING! Make sure
that no foreign material enters
the final transmission case.
Make sure that no oil gets on
the tire or wheel. [EWA11312]
Recommended final transmission
oil:
See page 8-1.
Oil quantity:
0.15 L (0.16 US qt, 0.13 Imp.qt)
8. Install the final transmission oil filler cap and its new O-ring, and
then tighten the oil filler cap.
9. Check the final transmission case
for oil leakage. If oil is leaking,
check for the cause.
To check the coolant level
1. Place the vehicle on the centerstand.
TIP
 The coolant level must be
checked on a cold engine since
the level varies with engine temperature.
 Make sure that the vehicle is positioned straight up when checking
the coolant level. A slight tilt to the
side can result in a false reading.
1. Coolant level check window
2. Maximum level mark
3. Minimum level mark
3. If the coolant is at or below the
minimum level mark, remove the
right floorboard mat by pulling it
up.
1
2. Check the coolant level through
the check window.
TIP
The coolant should be between the
minimum and maximum level marks.
6-13
1. Floorboard mat
6
U2DSE0E0.book Page 14 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
4. Remove the coolant reservoir cover.
1
be protected against frost and
corrosion. If water has been
added to the coolant, have a
Yamaha dealer check the antifreeze content of the coolant as
soon as possible, otherwise the
effectiveness of the coolant will
be reduced. [ECA10473]
5. Remove the coolant reservoir cap,
add coolant to the maximum level
mark, and then install the reservoir
cap. WARNING! Remove only
the coolant reservoir cap. Never
attempt to remove the radiator
cap when the engine is hot.
[EWA15162] NOTICE: If coolant is not
available, use distilled water or
soft tap water instead. Do not
use hard water or salt water
since it is harmful to the engine.
If water has been used instead
of coolant, replace it with coolant as soon as possible, otherwise the cooling system will not
1
1
1. Coolant reservoir cover
6
EAU67280
To change the coolant
1. Place the vehicle on a level surface and let the engine cool if necessary.
2. Remove panels A and B. (See
page 6-7.)
3. Remove the radiator cover by removing the bolts.
2
1. Coolant reservoir cap
Coolant reservoir capacity (up to
the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
6. Install the coolant reservoir cover.
7. Place the right floorboard mat in
the original position and push it
downward to secure it.
6-14
1. Radiator cover
2. Bolt
4. Place a container under the engine to collect the used coolant.
5. Remove
the
radiator
cap.
WARNING! Never attempt to remove the radiator cap when the
engine is hot. [EWA10382]
U2DSE0E0.book Page 15 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
9. Remove the coolant reservoir cap,
and then turn the coolant reservoir
upside down to empty it.
10. After the coolant is completely
drained, thoroughly flush the cooling system with clean tap water.
11. Install the coolant reservoir by installing the bolt.
12. Install the coolant drain bolt and
its new gasket, and then tighten
the bolt to the specified torque.
1
2
1
1. Radiator cap
6. Remove the coolant drain screw
and its O-ring to drain the cooling
system.
1. Coolant drain bolt
2. Gasket
8. Remove the coolant reservoir by
removing the bolt.
1
2
2
3
1
1. Coolant drain screw
2. O-ring
7. Remove the coolant drain bolt and
its gasket to drain the cooling system.
1. Coolant reservoir cap
2. Coolant reservoir
3. Bolt
6-15
Tightening torque:
Coolant drain bolt:
10 Nm (1.0 m·kgf, 7.2 ft·lbf)
13. Install the coolant drain screw and
its new O-ring.
14. Pour the recommended coolant
into the reservoir to the maximum
level mark, and then install the
coolant reservoir cap.
15. Pour the recommended coolant
into the radiator until it is full.
6
U2DSE0E0.book Page 16 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU67171
Antifreeze/water mixture ratio:
1:1
Recommended antifreeze:
High-quality ethylene glycol antifreeze containing corrosion inhibitors for aluminum engines
Coolant quantity:
Radiator (including all routes):
0.46 L (0.49 US qt, 0.40 Imp.qt)
Coolant reservoir (up to the maximum level mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
6
16. Install the radiator cap, start the
engine, let it idle for several minutes, and then turn it off.
17. Remove the radiator cap to check
the coolant level in the radiator. If
necessary, add sufficient coolant
until it reaches the top of the radiator, and then install the radiator
cap.
18. Start the engine, and then check
the vehicle for coolant leakage. If
coolant is leaking, have a Yamaha
dealer check the cooling system.
19. Install the radiator cover by installing the bolts.
20. Install the panels.
Air filter and V-belt case air filter elements
The air filter element should be replaced and the V-belt case air filter element should be cleaned at the
intervals specified in the periodic maintenance and lubrication chart. Service
the air filter elements more frequently if
you are riding in unusually wet or dusty
areas. The air filter check hose and Vbelt case air filter check hose must be
frequently checked and cleaned if necessary.
1
2
2
1. Air filter case cover
2. Screw
3. Pull the air filter element out.
1
Replacing the air filter element
1. Place the vehicle on the centerstand.
2. Remove the air filter case cover by
removing the screws.
1. Air filter element
4. Insert a new air filter element into
the air filter case. NOTICE: Make
sure that the air filter element is
properly seated in the air filter
case. The engine should never
6-16
U2DSE0E0.book Page 17 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
be operated without the air filter
element installed, otherwise the
piston(s) and/or cylinder(s) may
become
excessively
worn.
[ECA10482]
5. Install the air filter case cover by
installing the screws.
Cleaning the V-belt case air filter element
1. Place the vehicle on the centerstand.
2. Remove the screws, and then pull
the V-belt case air filter element
cover outward and away from the
V-belt case.
Cleaning the air filter check hose
point. [EWA10432] NOTICE: To avoid
damaging the air filter element,
handle it gently and carefully,
and do not twist it. [ECA10522]
2
1
1
1
6
1. V-belt case air filter element
2
1. Air filter check hose
1. Check the hose on the rear side of
the air filter case for accumulated
dirt or water.
2. If dirt or water is visible, remove
the hose from the clamp, clean it,
and then install it.
1. V-belt case air filter element cover
2. Screw
3. Pull the V-belt case air filter element out, and then clean it with
solvent. After cleaning, remove
the remaining solvent by squeezing the element. WARNING! Use
only a dedicated parts cleaning
solvent. To avoid the risk of fire
or explosion, do not use gasoline or solvents with a low flash
6-17
4. Apply oil of the recommended
type to the entire surface of the
sponge material, and then
squeeze the excess oil out.
U2DSE0E0.book Page 18 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
TIP
The air filter element should be wet but
not dripping.
2. If dirt or water is visible, remove
the hose from the clamp, clean it,
and then install it.
EAU21385
Checking the throttle grip free
play
Recommended oil:
Yamaha foam air filter oil or other
quality foam air filter oil
5. Insert the element into the V-belt
case.
6. Install the air filter element cover
by installing the screws.
6
1
1. Throttle grip free play
Cleaning the V-belt case check hose
The throttle grip free play should measure 3.0–5.0 mm (0.12–0.20 in) at the
inner edge of the throttle grip. Periodically check the throttle grip free play
and, if necessary, have a Yamaha dealer adjust it.
1
1. V-belt case check hose
1. Check the hose on the rear side of
the V-belt case for accumulated
dirt or water.
6-18
U2DSE0E0.book Page 19 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU21402
EAUN0701
Valve clearance
Tires
The valve clearance changes with use,
resulting in improper air-fuel mixture
and/or engine noise. To prevent this
from occurring, the valve clearance
must be adjusted by a Yamaha dealer
at the intervals specified in the periodic
maintenance and lubrication chart.
Tires are the only contact between the
vehicle and the road. Safety in all conditions of riding depends on a relatively
small area of road contact. Therefore, it
is essential to maintain the tires in good
condition at all times and replace them
at the appropriate time with the specified tires.
Tire air pressure
The tire air pressure should be
checked and, if necessary, adjusted
before each ride.
EWA10504
WARNING
Operation of this vehicle with improper tire pressure may cause severe injury or death from loss of
control.
 The tire air pressure must be
checked and adjusted on cold
tires (i.e., when the temperature
of the tires equals the ambient
temperature).
 The tire air pressure must be
adjusted in accordance with the
riding speed and with the total
6-19
weight of rider, passenger, cargo, and accessories approved
for this model.
Tire air pressure (measured on cold
tires):
Front (1 person):
150 kPa (1.50 kgf/cm2, 22 psi)
Rear (1 person):
250 kPa (2.50 kgf/cm2, 36 psi)
Front (2 persons):
150 kPa (1.50 kgf/cm2, 22 psi)
Rear (2 persons):
250 kPa (2.50 kgf/cm2, 36 psi)
Maximum load*:
168 kg (370 lb)
* Total weight of rider, passenger, cargo and accessories
EWA10512
WARNING
Never overload your vehicle. Operation of an overloaded vehicle could
cause an accident.
6
U2DSE0E0.book Page 20 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
Tire inspection
1. Tire sidewall
2. Tire tread depth
6
The tires must be checked before each
ride. If the center tread depth reaches
the specified limit, if the tire has a nail
or glass fragments in it, or if the sidewall is cracked, have a Yamaha dealer
replace the tire immediately.
Minimum tire tread depth (front and
rear):
1.6 mm (0.06 in)
TIP
The tire tread depth limits may differ
from country to country. Always comply with the local regulations.
EWA10472
WARNING
 Have a Yamaha dealer replace
excessively worn tires. Besides
being illegal, operating the vehicle with excessively worn tires
decreases riding stability and
can lead to loss of control.
 The replacement of all wheel
and brake-related parts, including the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowledge and experience to do so.
 Ride at moderate speeds after
changing a tire since the tire
surface must first be “broken
in” for it to develop its optimal
characteristics.
Tire information
This model is equipped with tubeless
tires and rubber tire air valves.
Tires age, even if they have not been
used or have only been used occasionally. Cracking of the tread and sidewall
rubber, sometimes accompanied by
carcass deformation, is an evidence of
6-20
ageing. Old and aged tires shall be
checked by tire specialists to ascertain
their suitability for further use.
EWA10462
WARNING
The front and rear tires should be of
the same make and design, otherwise the handling characteristics of
the vehicle may be different, which
could lead to an accident.
After extensive tests, only the tires listed below have been approved for this
model by Yamaha.
Front tire:
Size:
110/70-13M/C 48P
Manufacturer/model:
DUNLOP/SCOOTSMART
Rear tire:
Size:
130/70-13M/C 63P
Manufacturer/model:
DUNLOP/SCOOTSMART
U2DSE0E0.book Page 21 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU21963
Cast wheels
To maximize the performance, durability, and safe operation of your vehicle,
note the following points regarding the
specified wheels.
 The wheel rims should be
checked for cracks, bends, warpage or other damage before each
ride. If any damage is found, have
a Yamaha dealer replace the
wheel. Do not attempt even the
smallest repair to the wheel. A deformed or cracked wheel must be
replaced.
 The wheel should be balanced
whenever either the tire or wheel
has been changed or replaced. An
unbalanced wheel can result in
poor performance, adverse handling characteristics, and a shortened tire life.
EAU50861
Checking the front and rear
brake lever free play
Front
There should be no free play at the
brake lever ends. If there is free play,
have a Yamaha dealer inspect the
brake system.
EWA14212
1
1. No brake lever free play
Rear
1
1. No brake lever free play
6-21
WARNING
A soft or spongy feeling in the brake
lever can indicate the presence of
air in the hydraulic system. If there is
air in the hydraulic system, have a
Yamaha dealer bleed the system before operating the vehicle. Air in the
hydraulic system will diminish the
braking performance, which may result in loss of control and an accident.
6
U2DSE0E0.book Page 22 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
Checking the front and rear
brake pads
indicator grooves have almost disappeared, have a Yamaha dealer replace
the brake pads as a set.
The front and rear brake pads must be
checked for wear at the intervals specified in the periodic maintenance and
lubrication chart.
Rear brake pads
EAU22393
EAU22461
EAU22582
Checking the brake fluid level
Before riding, check that the brake fluid
is above the minimum level mark.
Check the brake fluid level with the top
of the reservoir level. Replenish the
brake fluid if necessary.
Front brake
EAU22432
Front brake pads
6
1
1
1
1
1. Brake pad wear indicator
1. Brake pad wear indicator groove
Each front brake pad is provided with
wear indicator grooves, which allow
you to check the brake pad wear without having to disassemble the brake.
To check the brake pad wear, check
the wear indicator grooves. If a brake
pad has worn to the point that the wear
Each rear brake pad is provided with a
wear indicator, which allows you to
check the brake pad wear without having to disassemble the brake. To check
the brake pad wear, check the position
of the wear indicator while applying the
brake. If a brake pad has worn to the
point that the wear indicator almost
touches the brake disc, have a
Yamaha dealer replace the brake pads
as a set.
6-22
1. Minimum level mark
U2DSE0E0.book Page 23 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
 Use only the specified brake fluid; otherwise, the rubber seals
may deteriorate, causing leakage.
 Refill with the same type of
brake fluid. Adding a brake fluid
other than DOT 4 may result in a
harmful chemical reaction.
 Be careful that water does not
enter the brake fluid reservoir
when refilling. Water will significantly lower the boiling point of
the fluid and may result in vapor
lock.
Rear brake
1
1. Minimum level mark
Specified brake fluid:
DOT 4
ECA17641
EWA15991
WARNING
Improper maintenance can result in
loss of braking ability. Observe
these precautions:
 Insufficient brake fluid may allow air to enter the brake system,
reducing
braking
performance.
 Clean the filler cap before removing. Use only DOT 4 brake
fluid from a sealed container.
NOTICE
Brake fluid may damage painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
As the brake pads wear, it is normal for
the brake fluid level to gradually go
down. A low brake fluid level may indicate worn brake pads and/or brake
system leakage; therefore, be sure to
check the brake pads for wear and the
brake system for leakage. If the brake
6-23
fluid level goes down suddenly, have a
Yamaha dealer check the cause before
further riding.
6
U2DSE0E0.book Page 24 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU22733
6
EAUU0311
Changing the brake fluid
Checking the V-belt
Have a Yamaha dealer change the
brake fluid at the intervals specified in
the periodic maintenance and lubrication chart. In addition, have the oil seals
of the master cylinders and calipers as
well as the brake hoses replaced at the
intervals listed below or whenever they
are damaged or leaking.
 Oil seals: Replace every two
years.
 Brake hoses: Replace every four
years.
The V-belt must be checked and replaced by a Yamaha dealer at the intervals specified in the periodic
maintenance and lubrication chart.
EAU23098
Checking and lubricating the
cables
The operation of all control cables and
the condition of the cables should be
checked before each ride, and the cables and cable ends should be lubricated if necessary. If a cable is
damaged or does not move smoothly,
have a Yamaha dealer check or replace it. WARNING! Damage to the
outer housing of cables may result
in internal rusting and cause interference with cable movement. Replace damaged cables as soon as
possible to prevent unsafe conditions. [EWA10712]
Recommended lubricant:
Yamaha cable lubricant or other
suitable cable lubricant
6-24
U2DSE0E0.book Page 25 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU49921
Checking and lubricating the
throttle grip and cable
The operation of the throttle grip
should be checked before each ride. In
addition, the cable should be lubricated by a Yamaha dealer at the intervals
specified in the periodic maintenance
chart.
EAU23173
Lubricating the front and rear
brake levers
Recommended lubricant:
Silicone grease
Front brake lever
6
Rear brake lever
The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic maintenance and lubrication chart.
6-25
U2DSE0E0.book Page 26 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU23215
Checking and lubricating the
centerstand and sidestand
EAU23273
Recommended lubricant:
Lithium-soap-based grease
Checking the front fork
The condition and operation of the
front fork must be checked as follows
at the intervals specified in the periodic
maintenance and lubrication chart.
To check the condition
Check the inner tubes for scratches,
damage and excessive oil leakage.
6
To check the operation
1. Place the vehicle on a level surface and hold it in an upright position. WARNING! To avoid injury,
securely support the vehicle so
there is no danger of it falling
over. [EWA10752]
2. While applying the front brake,
push down hard on the handlebars several times to check if the
front fork compresses and rebounds smoothly.
The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-tometal contact surfaces should be lubricated if necessary.
EWA10742
WARNING
If the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or repair it. Otherwise, the centerstand or
sidestand could contact the ground
and distract the operator, resulting
in a possible loss of control.
6-26
U2DSE0E0.book Page 27 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU45512
ECA10591
NOTICE
If any damage is found or the front
fork does not operate smoothly,
have a Yamaha dealer check or repair it.
EAU23292
Checking the steering
Checking the wheel bearings
Worn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as follows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place the vehicle on the centerstand. WARNING! To avoid injury, securely support the vehicle
so there is no danger of it falling
over. [EWA10752]
2. Hold the lower ends of the front
fork legs and try to move them forward and backward. If any free
play can be felt, have a Yamaha
dealer check or repair the steering.
The front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrication chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer
check the wheel bearings.
6-27
6
U2DSE0E0.book Page 28 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU50291
Battery
1
2
3
6
1. Battery
2. Positive battery lead (red)
3. Negative battery lead (black)
The battery is located under the seat.
(See page 3-15.)
This model is equipped with a VRLA
(Valve Regulated Lead Acid) battery.
There is no need to check the electrolyte or to add distilled water. However,
the battery lead connections need to
be checked and, if necessary, tightened.
EWA10761
burns. Avoid any contact with
skin, eyes or clothing and always shield your eyes when
working near batteries. In case
of contact, administer the following FIRST AID.
• EXTERNAL: Flush with plenty
of water.
• INTERNAL: Drink large quantities of water or milk and immediately call a physician.
• EYES: Flush with water for 15
minutes and seek prompt
medical attention.
 Batteries produce explosive hydrogen gas. Therefore, keep
sparks, flames, cigarettes, etc.,
away from the battery and provide sufficient ventilation when
charging it in an enclosed
space.
 KEEP THIS AND ALL BATTERIES OUT OF THE REACH OF
CHILDREN.
WARNING
 Electrolyte is poisonous and
dangerous since it contains sulfuric acid, which causes severe
To charge the battery
Have a Yamaha dealer charge the battery as soon as possible if it seems to
have discharged. Keep in mind that the
6-28
battery tends to discharge more quickly if the vehicle is equipped with optional electrical accessories.
ECA16522
NOTICE
To charge a VRLA (Valve Regulated
Lead Acid) battery, a special (constant-voltage) battery charger is required. Using a conventional battery
charger will damage the battery.
To store the battery
1. If the vehicle will not be used for
more than one month, remove the
battery, fully charge it, and then
place it in a cool, dry place.
NOTICE: When removing the
battery, be sure the key is
turned to “OFF”, then disconnect the negative lead before
disconnecting the positive lead.
[ECA16303]
2. If the battery will be stored for
more than two months, check it at
least once a month and fully
charge it if necessary.
3. Fully charge the battery before installation. NOTICE: When installing the battery, be sure the key
U2DSE0E0.book Page 29 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
is turned to “OFF”, then connect
the positive lead before connecting the negative lead. [ECA16841]
4. After installation, make sure that
the battery leads are properly connected to the battery terminals.
EAU66790
Replacing the fuses
1 2 3
4 5 6
The fuse boxes, which contain the fuses for the individual circuits, are located under the seat. (See page 3-15.)
8
7
ECA16531
NOTICE
Always keep the battery charged.
Storing a discharged battery can
cause permanent battery damage.
1
1.
2.
3.
4.
5.
6.
7.
8.
1. Fuse box
Main fuse 1
ABS solenoid fuse
Main fuse 2
Taillight fuse
Signaling system fuse
ABS control unit fuse
ABS motor fuse
Spare fuse
If a fuse is blown, replace it as follows.
1. Turn the key to “OFF” and turn off
the electrical circuit in question.
2. Open the seat. (See page 3-15.)
3. Remove the battery cover by removing the screws.
6-29
6
U2DSE0E0.book Page 30 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU62850
2
1
1. Battery cover
2. Screw
6
4. Remove the blown fuse, and then
install a new fuse of the specified
amperage. WARNING! Do not
use a fuse of a higher amperage
rating than recommended to
avoid causing extensive damage to the electrical system and
possibly a fire. [EWA15132]
Specified fuses:
Main fuse 1:
15.0 A
Main fuse 2:
7.5 A
Taillight fuse:
7.5 A
Signaling system fuse:
7.5 A
ABS motor fuse:
30.0 A
ABS solenoid fuse:
15.0 A
ABS control unit fuse:
7.5 A
5. Turn the key to “ON” and turn on
the electrical circuit in question to
check if the device operates.
6. If the fuse immediately blows
again, have a Yamaha dealer
check the electrical system.
7. Install the battery cover by installing the screws.
8. Close the seat.
6-30
Headlight
This model is equipped with an LEDtype headlight.
If a headlight does not come on, have
a Yamaha dealer check its electrical
circuit.
ECA16581
NOTICE
Do not affix any type of tinted film or
stickers to the headlight lens.
U2DSE0E0.book Page 31 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU67290
Replacing an auxiliary light
bulb
1
This model is equipped with two auxiliary lights. If an auxiliary light bulb
burns out, replace it as follows.
1. Remove the windshield by removing the screws.
1
2
1. Headlight cover
2. Bolt
1
2
2
1. Auxiliary light bulb
3. Remove the auxiliary light bulb
socket (together with the bulb) by
turning the socket counterclockwise.
5. Insert a new bulb into the socket.
6. Install the socket (together with
the bulb) by turning it clockwise.
7. Install the headlight cover by installing the bolts.
1. Windshield
2. Screw
2. Remove the headlight cover by removing the bolts.
1
1. Auxiliary light bulb socket
4. Remove the burnt-out bulb by
pulling it out.
6-31
8. Install the windshield by installing
the screws.
6
U2DSE0E0.book Page 32 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU67300
Brake light
This model is equipped with an LEDtype brake light.
If the brake light does not come on,
have a Yamaha dealer check it.
EAU67310
Replacing the taillight bulb
1
1. Open the seat. (See page 3-15.)
2. Remove the grab bar by removing
the bolts.
2
1
2
1. Taillight cover
2. Screw
4. Remove the quick fasteners and
screws.
6
1. Grab bar
2. Bolt
1
3. Remove the taillight cover by removing the screws.
1. Quick fastener
6-32
U2DSE0E0.book Page 33 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
1
2
1
1
2
1. Screw
2. Quick fastener
1. Taillight unit
2. Side cover
1. Taillight bulb
6. Remove the taillight bulb socket
(together with the bulb) by turning
it counterclockwise.
1
1
2
1. Screw
2. Quick fastener
5. Pull the left and right side covers
slightly outward and pull the taillight unit rearward.
1. Taillight bulb socket
7. Remove the burnt-out bulb by
pulling it out.
6-33
8. Insert a new bulb into the socket.
9. Install the socket (together with
the bulb) by turning it clockwise.
10. Place the taillight unit in the original position, and then install the
screws and quick fasteners.
11. Install the taillight cover by installing the screws.
6
U2DSE0E0.book Page 34 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
12. Install the grab bar by installing the
bolts, and then tightening them to
the specified torque.
Tightening torque:
Grab bar bolt:
17 Nm (1.7 m·kgf, 12 ft·lbf)
13. Close the seat.
EAU43054
Replacing a front turn signal
light bulb
1
1. Place the vehicle on the centerstand.
2. Remove the turn signal light bulb
socket (together with the bulb) by
turning it counterclockwise.
1. Turn signal light bulb
1
6
1. Turn signal light bulb socket
3. Remove the burnt-out bulb by
pulling it out.
6-34
4. Insert a new bulb into the socket.
5. Install the socket (together with
the bulb) by turning it clockwise.
U2DSE0E0.book Page 35 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU67320
Replacing a rear turn signal
light bulb
1
2
1
1. Open the seat. (See page 3-15.)
2. Remove the grab bar by removing
the bolts.
1
2
1. Taillight cover
2. Screw
1. Turn signal light bulb
4. Remove the turn signal light bulb
socket (together with the bulb) by
turning it counterclockwise.
1. Grab bar
2. Bolt
6. Insert a new bulb into the socket.
7. Install the socket (together with
the bulb) by turning it clockwise.
8. Install the taillight cover by installing the screws.
1
3. Remove the taillight cover by removing the screws.
1. Turn signal light bulb socket
5. Remove the burnt-out bulb by
pulling it out.
6-35
9. Install the grab bar by installing the
bolts, and then tightening them to
the specified torque.
6
U2DSE0E0.book Page 36 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU25882
Tightening torque:
Grab bar bolt:
17 Nm (1.7 m·kgf, 12 ft·lbf)
10. Close the seat.
6
Troubleshooting
Although Yamaha scooters receive a
thorough inspection before shipment
from the factory, trouble may occur
during operation. Any problem in the
fuel, compression, or ignition systems,
for example, can cause poor starting
and loss of power.
The following troubleshooting charts
represent quick and easy procedures
for checking these vital systems yourself. However, should your scooter require any repair, take it to a Yamaha
dealer, whose skilled technicians have
the necessary tools, experience, and
know-how to service the scooter properly.
Use only genuine Yamaha replacement parts. Imitation parts may look
like Yamaha parts, but they are often
inferior, have a shorter service life and
can lead to expensive repair bills.
EWA15142
WARNING
When checking the fuel system, do
not smoke, and make sure there are
no open flames or sparks in the area, including pilot lights from water
6-36
heaters or furnaces. Gasoline or
gasoline vapors can ignite or explode, causing severe injury or property damage.
U2DSE0E0.book Page 37 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
EAU42706
Troubleshooting charts
Starting problems or poor engine performance
1. Fuel
There is enough fuel.
Check the battery.
There is no fuel.
Supply fuel.
Check the fuel level in
the fuel tank.
2. Battery
The engine does not start.
Check the battery.
The engine turns over
quickly.
The battery is good.
The engine turns over
slowly.
Check the battery lead connections,
and have a Yamaha dealer charge
the battery if necessary.
Operate the electric starter.
3. Ignition
The engine does not start.
Check the ignition.
Wet
Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.
Operate the electric starter.
Dry
Have a Yamaha dealer check the vehicle.
The engine does not start.
Check the compression.
Remove the spark plug
and check the electrodes.
4. Compression
There is compression.
The engine does not start.
Have a Yamaha dealer check the vehicle.
There is no compression.
Have a Yamaha dealer check the vehicle.
Operate the electric starter.
6-37
6
U2DSE0E0.book Page 38 Thursday, March 19, 2015 10:34 AM
Periodic maintenance and adjustment
Engine overheating
EWAT1041
WARNING
 Do not remove the radiator cap when the engine and radiator are hot. Scalding hot fluid and steam may be
blown out under pressure, which could cause serious injury. Be sure to wait until the engine has cooled.
 Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the cap counterclockwise to the
detent to allow any residual pressure to escape. When the hissing sound has stopped, press down on the cap
while turning it counterclockwise, and then remove the cap.
The coolant level is low.
Check the cooling system
for leakage.
6
Wait until the
engine has cooled.
Check the coolant level in the
reservoir and radiator.
The coolant level
is OK.
There is
leakage.
There is
no leakage.
Have a Yamaha dealer check
and repair the cooling system.
Add coolant. (See TIP.)
Start the engine. If the engine overheats again, have a
Yamaha dealer check and repair the cooling system.
TIP
If coolant is not available, tap water can be temporarily used instead, provided that it is changed to the recommended coolant as soon as possible.
6-38
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Scooter care and storage
EAU37834
Matte color caution
EAUN1000
Care
ECA15193
NOTICE
Some models are equipped with
matte colored finished parts. Be
sure to consult a Yamaha dealer for
advice on what products to use before cleaning the vehicle. Using a
brush, harsh chemical products or
cleaning compounds when cleaning
these parts will scratch or damage
their surface. Wax also should not
be applied to any matte colored finished parts.
While the open design of a scooter reveals the attractiveness of the technology, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed
on a car, however, it detracts from the
overall appearance of a scooter. Frequent and proper care does not only
comply with the terms of the warranty,
but it will also keep your scooter looking good, extend its life and optimize
its performance.
Before cleaning
1. Cover the muffler outlet with a
plastic bag after the engine has
cooled down.
2. Make sure that all caps and covers as well as all electrical couplers and connectors, including
the spark plug cap, are tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod7-1
ucts onto seals, gaskets and
wheel axles. Always rinse the dirt
and degreaser off with water.
Cleaning
ECA10784
NOTICE
 Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are
used on hard-to-remove dirt, do
not leave the cleaner on the affected area any longer than instructed. Also, thoroughly rinse
the area off with water, immediately dry it, and then apply a corrosion protection spray.
 Improper cleaning can damage
plastic parts (such as cowlings,
panels, windshields, headlight
lenses, meter lenses, etc.) and
the mufflers. Use only a soft,
clean cloth or sponge with water to clean plastic. However, if
the plastic parts cannot be thoroughly cleaned with water, diluted mild detergent with water
may be used. Be sure to rinse
7
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Scooter care and storage
7
off any detergent residue using
plenty of water, as it is harmful
to plastic parts.
 Do not use any harsh chemical
products on plastic parts. Be
sure to avoid using cloths or
sponges which have been in
contact with strong or abrasive
cleaning products, solvent or
thinner, fuel (gasoline), rust removers or inhibitors, brake fluid,
antifreeze or electrolyte.
 Do not use high-pressure washers or steam-jet cleaners since
they cause water seepage and
deterioration in the following areas: seals (of wheel and swingarm bearings, fork and brakes),
electric components (couplers,
connectors,
instruments,
switches and lights), breather
hoses and vents.
 For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as
they will cause dulling or
scratching. Some cleaning
compounds for plastic may
leave scratches on the wind-
shield. Test the product on a
small hidden part of the windshield to make sure that it does
not leave any marks. If the windshield is scratched, use a quality
plastic polishing compound after washing.
After normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge,
and then rinse thoroughly with clean
water. Use a toothbrush or bottlebrush
for hard-to-reach areas. Stubborn dirt
and insects will come off more easily if
the area is covered with a wet cloth for
a few minutes before cleaning.
After riding in the rain, near the sea, or
on salt-sprayed roads
Since sea salt or salt sprayed on roads
during winter are extremely corrosive
in combination with water, carry out
the following steps after each ride in
the rain, near the sea, or on saltsprayed roads.
7-2
TIP
Salt sprayed on roads in the winter
may remain well into spring.
1. Clean the scooter with cold water
and a mild detergent after the engine has cooled down. NOTICE:
Do not use warm water since it
increases the corrosive action
of the salt. [ECA10792]
2. Apply a corrosion protection spray
on all metal, including chromeand nickel-plated, surfaces to prevent corrosion.
Cleaning the windshield
Avoid using any alkaline or strong acid
cleaner, gasoline, brake fluid, or any
other solvent. Clean the windshield
with a cloth or sponge dampened with
a neutral detergent, and after cleaning,
thoroughly wash it off with water. For
additional cleaning, use Yamaha Windshield Cleaner or other quality cleaner.
Some cleaning compounds for plastics
may leave scratches on surfaces of the
windshield. Before using them, make a
test by polishing an area which does
not affect your visibility.
U2DSE0E0.book Page 3 Thursday, March 19, 2015 10:34 AM
Scooter care and storage
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainlesssteel parts, including the exhaust
system. (Even the thermally induced discoloring of stainlesssteel exhaust systems can be removed through polishing.)
3. To prevent corrosion, it is recommended to apply a corrosion protection spray on all metal,
including chrome- and nickel-plated, surfaces.
4. Use spray oil as a universal cleaner to remove any remaining dirt.
5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely before storing or covering it.
discs and brake linings with a
regular brake disc cleaner or
acetone, and wash the tires with
warm water and a mild detergent.
 Before operating the scooter
test its braking performance
and cornering behavior.
ECAU0022
NOTICE
 Apply spray oil and wax sparingly and make sure to wipe off
any excess.
 Never apply oil or wax to any
rubber parts, plastic parts or
headlight, taillight and meter
lenses, but treat them with a
suitable care product.
 Avoid using abrasive polishing
compounds as they will wear
away the paint.
EWA10943
WARNING
Contaminants on the brakes or tires
can cause loss of control.
 Make sure that there is no oil or
wax on the brakes or tires. If
necessary, clean the brake
on for a short period of time will
help remove the moisture from the
lens.
TIP
 Consult a Yamaha dealer for advice on what products to use.
 Washing, rainy weather or humid
climates can cause the headlight
lens to fog. Turning the headlight
7-3
7
U2DSE0E0.book Page 4 Thursday, March 19, 2015 10:34 AM
Scooter care and storage
EAU36564
Storage
Short-term
Always store your scooter in a cool, dry
place and, if necessary, protect it
against dust with a porous cover. Be
sure the engine and the exhaust system are cool before covering the
scooter.
ECA10821
NOTICE
7
 Storing the scooter in a poorly
ventilated room or covering it
with a tarp, while it is still wet,
will allow water and humidity to
seep in and cause rust.
 To prevent corrosion, avoid
damp cellars, stables (because
of the presence of ammonia)
and areas where strong chemicals are stored.
Long-term
Before storing your scooter for several
months:
1. Follow all the instructions in the
“Care” section of this chapter.
2. Fill up the fuel tank and add fuel
stabilizer (if available) to prevent
the fuel tank from rusting and the
fuel from deteriorating.
3. Perform the following steps to
protect the cylinder, piston rings,
etc. from corrosion.
a. Remove the spark plug cap
and spark plug.
b. Pour a teaspoonful of engine
oil into the spark plug bore.
c. Install the spark plug cap onto
the spark plug, and then place
the spark plug on the cylinder
head so that the electrodes are
grounded. (This will limit sparking during the next step.)
d. Turn the engine over several
times with the starter. (This will
coat the cylinder wall with oil.)
e. Remove the spark plug cap
from the spark plug, and then
install the spark plug and the
spark plug cap. WARNING! To
prevent damage or injury
from sparking, make sure to
ground the spark plug electrodes while turning the engine over. [EWA10952]
7-4
4. Lubricate all control cables and
the pivoting points of all levers and
pedals as well as of the sidestand/centerstand.
5. Check and, if necessary, correct
the tire air pressure, and then lift
the scooter so that both of its
wheels are off the ground. Alternatively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.
6. Cover the muffler outlet with a
plastic bag to prevent moisture
from entering it.
7. Remove the battery and fully
charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an excessively cold or warm place [less
than 0 °C (30 °F) or more than 30
°C (90 °F)]. For more information
on storing the battery, see page
6-28.
TIP
Make any necessary repairs before
storing the scooter.
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Specifications
Dimensions:
Overall length:
1955 mm (77.0 in)
Overall width:
740 mm (29.1 in)
Overall height:
1115 mm (43.9 in)
Seat height:
765 mm (30.1 in)
Wheelbase:
1350 mm (53.1 in)
Ground clearance:
135 mm (5.31 in)
Minimum turning radius:
2000 mm (78.7 in)
Weight:
Curb weight:
127 kg (280 lb)
Engine:
Engine type:
Liquid cooled 4-stroke, SOHC
Cylinder arrangement:
Single cylinder
Displacement:
125 cm3
Bore × stroke:
52.0 × 58.7 mm (2.05 × 2.31 in)
Compression ratio:
11.2 : 1
Starting system:
Electric starter
Lubrication system:
Wet sump
Engine oil:
Air filter:
Recommended brand:
YAMALUBE
Type:
SAE 10W-40 or 20W-40
0
10
30
50
70
Air filter element:
Oil-coated paper element
Fuel:
90 110 130 ˚F
Recommended fuel:
Regular unleaded gasoline (Gasohol (E10)
acceptable)
Fuel tank capacity:
6.6 L (1.74 US gal, 1.45 Imp.gal)
Fuel injection:
SAE 10W-40
Throttle body:
ID mark:
2DS1 00
SAE 20W-40
Spark plug(s):
-20 -10
0
10
20
30
40
50 ˚C
Recommended engine oil grade:
API service SG type or higher, JASO
standard MA or MB
Engine oil quantity:
Periodic oil change:
0.90 L (0.95 US qt, 0.79 Imp.qt)
Final transmission oil:
Type:
YAMALUBE 10W-40 or SAE 10W-30 type
SE motor oil
Quantity:
0.15 L (0.16 US qt, 0.13 Imp.qt)
Coolant quantity:
Coolant reservoir (up to the maximum level
mark):
0.25 L (0.26 US qt, 0.22 Imp.qt)
Radiator (including all routes):
0.46 L (0.49 US qt, 0.40 Imp.qt)
8-1
Manufacturer/model:
NGK/CPR8EA-9
Spark plug gap:
0.8–0.9 mm (0.031–0.035 in)
Clutch:
Clutch type:
Dry, centrifugal automatic
Transmission:
Primary reduction ratio:
1.000
Final drive:
Gear
Secondary reduction ratio:
10.208 (56/16 x 35/12)
Transmission type:
V-belt automatic
Chassis:
Frame type:
Underbone
8
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Specifications
Caster angle:
26.00 °
Trail:
92 mm (3.6 in)
Front tire:
Type:
Tubeless
Size:
110/70-13M/C 48P
Manufacturer/model:
DUNLOP/SCOOTSMART
Rear tire:
Type:
Tubeless
Size:
130/70-13M/C 63P
Manufacturer/model:
DUNLOP/SCOOTSMART
Loading:
8
Maximum load:
168 kg (370 lb)
(Total weight of rider, passenger, cargo
and accessories)
Tire air pressure (measured on cold
tires):
Front (1 person):
150 kPa (1.50 kgf/cm2, 22 psi)
Rear (1 person):
250 kPa (2.50 kgf/cm2, 36 psi)
Front (2 persons):
150 kPa (1.50 kgf/cm2, 22 psi)
Rear (2 persons):
250 kPa (2.50 kgf/cm2, 36 psi)
Front wheel:
Wheel type:
Cast wheel
Rim size:
13M/C x MT3.00
Rear wheel:
Wheel type:
Cast wheel
Rim size:
13M/C x MT3.50
Front brake:
Type:
Single disc brake
Operation:
Right hand operation
Specified brake fluid:
DOT 4
Rear brake:
Type:
Single disc brake
Operation:
Left hand operation
Specified brake fluid:
DOT 4
Front suspension:
Type:
Telescopic fork
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
100 mm (3.9 in)
Rear suspension:
Type:
Unit swing
8-2
Spring/shock absorber type:
Coil spring/oil damper
Wheel travel:
90 mm (3.5 in)
Electrical system:
System voltage:
12 V
Ignition system:
TCI
Charging system:
AC magneto
Battery:
Model:
YTZ7V
Voltage, capacity:
12 V, 6.0 Ah
Bulb voltage, wattage × quantity:
Headlight:
LED
Brake/tail light:
12 V, LED/10.0 W × 1
Front turn signal light:
12 V, 10.0 W × 2
Rear turn signal light:
12 V, 10.0 W × 2
Auxiliary light:
12 V, 5.0 W × 2
Meter lighting:
LED
High beam indicator light:
LED
Turn signal indicator light:
LED
U2DSE0E0.book Page 3 Thursday, March 19, 2015 10:34 AM
Specifications
Coolant temperature warning light:
LED
Engine trouble warning light:
LED
ABS warning light:
LED
Fuses:
Main fuse 1:
15.0 A
Main fuse 2:
7.5 A
Taillight fuse:
7.5 A
Signaling system fuse:
7.5 A
ABS control unit fuse:
7.5 A
ABS motor fuse:
30.0 A
ABS solenoid fuse:
15.0 A
8
8-3
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Consumer information
EAU53562
Identification numbers
Record the vehicle identification number, engine serial number, and the
model label information in the spaces
provided below. These identification
numbers are needed when registering
the vehicle with the authorities in your
area and when ordering spare parts
from a Yamaha dealer.
VEHICLE IDENTIFICATION NUMBER:
ENGINE SERIAL NUMBER:
9
EAU26411
Vehicle identification number
EAU26442
Engine serial number
1
1
1. Vehicle identification number
1. Engine serial number
The vehicle identification number is
stamped into the frame.
The engine serial number is stamped
into the crankcase.
TIP
The vehicle identification number is
used to identify your vehicle and may
be used to register it with the licensing
authority in your area.
EAU26501
Model label
1
MODEL LABEL INFORMATION:
1. Model label
9-1
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Consumer information
The model label is affixed to the inside
of the rear storage compartment. (See
page 3-16.) Record the information on
this label in the space provided. This
information will be needed when ordering spare parts from a Yamaha dealer.
9
9-2
U2DSE0E0.book Page 1 Thursday, March 19, 2015 10:34 AM
Index
A
Front and rear brake lever free play,
checking............................................. 6-21
Front and rear brake pads, checking ... 6-22
Front fork, checking ............................. 6-26
Fuel....................................................... 3-13
Fuel consumption, tips for reducing ...... 5-3
Fuel tank cap........................................ 3-12
Fuel tank overflow hose ....................... 3-14
Fuses, replacing ................................... 6-29
ABS.......................................................3-11
ABS warning light ...................................3-3
Acceleration and deceleration ................5-2
Air filter and V-belt case air filter
elements .............................................6-16
Auxiliary light bulb, replacing................6-31
B
Battery ..................................................6-28
Brake fluid, changing ............................6-24
Brake fluid level, checking ....................6-22
Brake lever, front ..................................3-10
Brake lever, rear....................................3-11
Brake levers, lubricating .......................6-25
Brake light.............................................6-32
Braking....................................................5-2
C
Cables, checking and lubricating .........6-24
Care ........................................................7-1
Catalytic converter................................3-14
Centerstand and sidestand,
checking and lubricating ....................6-26
Coolant .................................................6-13
Coolant temperature warning light .........3-3
D
Dimmer switch ......................................3-10
10
E
Engine break-in.......................................5-3
Engine oil and oil strainer......................6-10
Engine serial number ..............................9-1
Engine trouble warning light ...................3-3
F
Final transmission oil ............................6-12
Safety information...................................1-1
Seat.......................................................3-15
Sidestand ..............................................3-17
Spark plug, checking ..............................6-8
Specifications .........................................8-1
Starting off ..............................................5-2
Starting the engine..................................5-1
Start switch ...........................................3-10
Steering, checking ................................6-27
Storage ...................................................7-4
Storage compartments .........................3-16
H
Handlebar switches.............................. 3-10
Headlight .............................................. 6-30
High beam indicator light ....................... 3-3
Horn switch .......................................... 3-10
I
Identification numbers............................ 9-1
Ignition circuit cut-off system............... 3-17
Indicator lights and warning lights ......... 3-2
K
Keyhole shutter ...................................... 3-2
M
Main switch/steering lock....................... 3-1
Maintenance and lubrication, periodic ... 6-3
Maintenance, emission control
system.................................................. 6-2
Matte color, caution ............................... 7-1
Model label............................................. 9-1
Multi-function meter unit ........................ 3-4
P
Panels, removing and installing.............. 6-7
Parking ................................................... 5-4
Part locations ......................................... 2-1
S
Safe-riding points ................................... 1-5
10-1
T
Taillight bulb, replacing .........................6-32
Throttle grip and cable,
checking and lubricating ....................6-25
Throttle grip free play, checking ...........6-18
Tires ......................................................6-19
Tool kit ....................................................6-1
Troubleshooting ....................................6-36
Troubleshooting charts .........................6-37
Turn signal indicator lights ......................3-2
Turn signal light bulb (front),
replacing .............................................6-34
Turn signal light bulb (rear),
replacing .............................................6-35
Turn signal switch .................................3-10
V
Valve clearance.....................................6-19
V-belt, checking ....................................6-24
Vehicle identification number..................9-1
W
Wheel bearings, checking.....................6-27
Wheels ..................................................6-21
U2DSE0E0.book Page 2 Thursday, March 19, 2015 10:34 AM
Original instructions
PRINTED IN INDONESIA
2015.04-*.*×1 CR
DIC183
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement