Crossland X, v.6 (rev 2), en-VX (Work nr: PP-112049_50)

Crossland X, v.6 (rev 2), en-VX (Work nr: PP-112049_50)
Contents
Introduction .................................... 2
In brief ............................................ 6
Keys, doors and windows ............ 21
Seats, restraints ........................... 42
Storage ........................................ 64
Instruments and controls ............. 73
Lighting ...................................... 110
Climate control ........................... 119
Driving and operating ................. 131
Vehicle care ............................... 184
Service and maintenance .......... 223
Technical data ........................... 227
Customer information ................ 240
Index .......................................... 248
2
Introduction
Introduction
Introduction
Vehicle specific data
Please enter your vehicle's data on
the previous page to keep it easily
accessible. This information is
available in the sections "Service and
maintenance" and "Technical data"
as well as on the identification plate.
Introduction
Your vehicle is a designed
combination of advanced technology,
safety, environmental friendliness
and economy.
This Owner's Manual provides you
with all the necessary information to
enable you to drive your vehicle
safely and efficiently.
Make sure your passengers are
aware of the possible risk of accident
and injury which may result from
improper use of the vehicle.
You must always comply with the
specific laws and regulations of the
country that you are in. These laws
may differ from the information in this
Owner's Manual.
Disregarding the description given in
this manual may affect your warranty.
When this Owner's Manual refers to a
workshop visit, we recommend your
Vauxhall Authorised Repairer. For
gas vehicles, we recommend a
Vauxhall Authorised Repairer
licensed to service gas vehicles.
All Vauxhall Authorised Repairers
provide first-class service at
reasonable prices. Experienced
mechanics trained by Vauxhall work
according to specific Vauxhall
instructions.
The customer literature pack should
always be kept ready to hand in the
vehicle.
Using this manual
●
●
This manual describes all options
and features available for this
model. Certain descriptions,
including those for display and
menu functions, may not apply to
your vehicle due to model
variant, country specifications,
special equipment or
accessories.
The "In brief" section will give you
an initial overview.
●
●
●
●
●
●
●
3
The table of contents at the
beginning of this manual and
within each section shows where
the information is located.
The index will enable you to
search for specific information.
This Owner's Manual depicts lefthand drive vehicles. Operation is
similar for right-hand drive
vehicles.
The Owner's Manual uses the
engine identifier code. The
corresponding sales designation
and engineering code can be
found in the section "Technical
data".
Directional data, e.g. left or right,
or front or back, always relate to
the direction of travel.
Displays may not support your
specific language.
Display messages and interior
labelling are written in bold
letters.
4
Introduction
Danger, Warnings and
Cautions
9 Danger
Text marked 9 Danger provides
information on risk of fatal injury.
Disregarding this information may
endanger life.
9 Warning
Text marked 9 Warning provides
information on risk of accident or
injury. Disregarding this
information may lead to injury.
Caution
Text marked Caution provides
information on possible damage to
the vehicle. Disregarding this
information may lead to vehicle
damage.
Symbols
Page references are indicated with 3.
3 means "see page".
Chronological order to select menu
entries in the vehicle personalisation
is indicated with I.
Page references and index entries
refer to the indented headings given
in the section table of content.
Thank you for choosing a Vauxhall.
We wish you many hours of
pleasurable driving.
Your Vauxhall Team
Introduction
5
6
In brief
In brief
Vehicle unlocking
Tailgate
Press c to unlock the doors and load
compartment. Open the doors by
pulling the handles.
Press P to unlock the tailgate only.
After unlocking, press the touchpad
switch above the licence plate and
open the tailgate.
Radio remote control 3 22.
Central locking system 3 24.
Electronic key system 3 23.
Load compartment 3 30.
Initial drive information
In brief
Seat adjustment
Backrests inclination
Seat height
Turn handwheel. Do not lean on
backrest when adjusting.
Seat position 3 43.
Seat adjustment 3 44.
Lever pumping motion
up
: seat higher
down : seat lower
Longitudinal adjustment
Pull handle, slide seat, release
handle. Try to move the seat back and
forth to ensure that the seat is locked
in place.
Seat position 3 43.
Seat adjustment 3 44.
Seat position 3 43.
Seat adjustment 3 44.
7
8
In brief
Seat inclination
Head restraint adjustment
Seat belt
Press switch
top
: front end higher
bottom : front end lower
Press release button, adjust height,
engage.
Head restraints 3 42.
Pull out the seat belt and fasten in belt
buckle. The seat belt must not be
twisted and must fit close against the
body. The backrest must not be tilted
back too far (maximum approx. 25°).
To unfasten belt, press red button on
belt buckle.
Seat position 3 43.
Seat belts 3 48.
Airbag system 3 51.
Seat position 3 43.
Seat adjustment 3 44.
In brief
Mirror adjustment
9
Exterior mirrors
Steering wheel adjustment
Select the relevant exterior mirror by
pushing the mirror button to the left or
right. Adjust respective mirror by the
four-way control.
Convex mirrors 3 34.
Electric adjustment 3 34.
Folding mirrors 3 35.
Heated mirrors 3 35.
Unlock lever, adjust steering wheel,
then engage lever and ensure it is
fully locked. Do not adjust steering
wheel unless vehicle is stationary and
steering wheel lock has been
released.
Seat position 3 43.
Ignition positions 3 132.
Interior mirror
To adjust the mirror, move the mirror
housing in the desired direction.
Manual anti-dazzle interior mirror
3 36.
Automatic anti-dazzle interior mirror
3 36.
10
In brief
Instrument panel overview
In brief
1
2
3
4
Power windows ..................... 37
Exterior mirrors ..................... 34
Cruise control ..................... 151
Speed limiter ....................... 153
Turn and lane-change
signals, headlight flash,
low/high beam, high beam
assist ................................... 114
Exit lighting ......................... 117
Parking lights ...................... 115
5
6
Buttons for Driver
Information Centre ................ 95
Side air vents ...................... 128
Instruments .......................... 84
Driver Information Centre ...... 95
Buttons for Driver
Information Centre ................ 95
8 Windscreen wiper and
washer, rear wiper and
washer ................................. 75
9 Head-up display .................... 99
10 Centre air vents .................. 128
11 Hazard warning flashers .... 113
12 Info-Display .......................... 97
7
13 Centre air vent ...................... 97
14 Anti-theft alarm system
status LED ........................... 32
15 Central locking system .......... 24
16 Glovebox .............................. 64
17
18
19
20
Fuse box ............................ 201
Controls for Info-Display
operation ............................... 97
Climate control system ........ 120
USB charging port ................ 78
Parking assist/Advanced
parking assist ..................... 160
Lane departure warning ..... 173
Eco button for stop-start
system ................................. 137
Electronic Stability Control
and Traction Control .......... 149
21 Power outlet .......................... 78
22 Manual transmission .......... 147
Automatic transmission ...... 144
23 Manual parking brake ......... 148
24 Power button ....................... 133
25 Ignition switch ..................... 132
26
27
28
29
11
Steering wheel adjustment . . 74
Horn ..................................... 75
Bonnet release lever .......... 186
Storage ................................. 64
Fuse box ............................ 201
30 Head-up display .................... 99
31 Light switch ........................ 110
Headlight range
adjustment ......................... 112
Front/rear fog lights ............ 114
Instrument illumination ....... 116
12
In brief
Exterior lighting
AUTO : automatic light control
switches automatically
between daytime running
light and headlight
: sidelights
8
: headlights
9
Automatic light control 3 111.
Fog lights
Press button in light switch:
> : front fog lights
ø : rear fog light
Headlight flash, high beam and
low beam
headlight flash : pull lever
high beam
: push lever
low beam
: push or pull lever
High beam 3 111.
High beam assist 3 112
Headlight flash 3 111.
Adaptive forward lighting 3 112
Turn and lane-change signals
lever up
: right turn signal
lever down : left turn signal
Turn and lane-change signals
3 114.
Parking lights 3 115.
In brief
Hazard warning flashers
Horn
13
Washer and wiper systems
Windscreen wiper
Operated by pressing ¨.
Hazard warning flashers 3 113.
Press j.
HI
LO
INT
: fast
: slow
: interval wiping
or
AUTO : automatic wiping with rain
sensor
OFF : off
For single wipe when the wiper is off,
press lever down to position 1x.
Windscreen wiper 3 75.
14
In brief
Windscreen washer
Rear window wiper
Rear window washer
Pull lever.
Windscreen washer system 3 75.
Washer fluid 3 188.
Wiper blade replacement 3 191.
Turn outer cap to activate the rear
window wiper:
OFF : off
INT : intermittent operation
ON : continuous operation
Push lever.
Washer fluid is sprayed on the rear
window and the wiper wipes a few
times.
Rear window wiper/washer 3 77.
In brief
Climate control
Electronic climate control system
Heated rear window
15
Demisting and defrosting the
windows
Heating and ventilation system, air
conditioning system
Heating and ventilation system, air
conditioning system
The heating is operated by pressing
b.
Heated rear window 3 38.
The heating is operated by pressing
b.
Heated exterior mirrors
Pressing b also activates the heated
exterior mirrors.
Heated exterior mirrors 3 35.
●
●
●
●
●
Press à: the air distribution is
directed towards the windscreen.
Set temperature controller £ to
warmest level.
Switch on air conditioning A/C if
required.
Set fan speed Z to highest level.
Switch on heated rear window b.
16
●
In brief
Switch on heated
windscreen ,.
● Open side air vents as required
and direct them towards the door
windows.
Heating and ventilation system
3 119.
Air conditioning system 3 120.
Heated windscreen 3 39.
Electronic climate control system
Transmission
Manual transmission
●
Press à. The LED in the button
illuminates to indicate activation.
● Temperature and air distribution
are set automatically and the fan
runs at high speed.
● Switch on air conditioning by
pressing A/C, if required.
● Switch on heated rear window b.
● Switch on heated
windscreen ,.
Electronic climate control system
3 123.
To engage reverse on 5-speed
transmission, depress the clutch
pedal and then push and move the
selector lever to the right and rear.
In brief
Automatic transmission
17
Starting off
Check before starting off
●
●
●
To engage reverse on 6-speed
transmission, depress the clutch
pedal, pull the ring under the selector
lever and move the selector lever to
the left and front.
Manual transmission 3 147.
●
P
R
N
D
M
<
]
:
:
:
:
:
:
:
park position
reverse
neutral mode
automatic mode
manual mode
upshift
downshift
Automatic transmission 3 144.
●
tyre pressure and condition
3 205, 3 238
Engine oil level and fluid levels
3 187.
All windows, mirrors, exterior
lighting and number plates are
free from dirt, snow and ice and
are operational.
Proper position of mirrors, seats,
and seat belts 3 34, 3 43,
3 49.
Brake function at low speed,
particularly if the brakes are wet.
18
In brief
Starting the engine
Ignition switch
●
●
●
●
●
Turn key to position 1.
Move the steering wheel slightly
to release the steering wheel
lock.
Manual transmission: operate
clutch and brake pedal.
Automatic transmission: operate
brake pedal and move selector
lever to P or N.
Do not operate accelerator pedal.
Turn key to position 2 and
release after engine has been
started.
Diesel engine starts after control
indicator ! for preheating
extinguishes.
Starting the engine 3 135.
Start power button
Manual transmission: operate clutch
and brake pedal.
Automatic transmission: operate
brake pedal and move selector lever
to P or N.
Do not operate accelerator pedal.
Press and release Start/Stop button.
Diesel engine starts after control
indicator ! for preheating
extinguishes.
In brief
Stop-start system
Parking
9 Warning
●
If the vehicle is at a low speed or at a
standstill and certain conditions are
fulfilled, an Autostop is activated.
An Autostop is indicated by control
indicator D.
Manual transmission: to restart the
engine, depress the clutch pedal
again. Control indicator D
extinguishes.
Automatic transmission: to restart the
engine, release the brake pedal.
Control indicator D extinguishes.
Stop-start system 3 137.
●
●
●
Do not park the vehicle on an
easily ignitable surface. The
high temperature of the
exhaust system could ignite the
surface.
Always apply the parking
brake. Activate the manual
parking brake without pressing
the release button. Apply as
firmly as possible on a downhill
slope or uphill slope. Depress
brake pedal at the same time to
reduce operating force.
Switch off the engine.
If the vehicle is on a level
surface or uphill slope, engage
first gear or set the selector
lever to position P before
removing the ignition key or
switching off ignition on
vehicles with power button. On
an uphill slope, turn the front
wheels away from the kerb.
●
●
●
●
19
If the vehicle is on a downhill
slope, engage reverse gear or
set the selector lever to position
P before removing the ignition
key or switching off ignition on
vehicles with power button.
Turn the front wheels towards
the kerb.
Close the windows.
Remove the ignition key from
the ignition switch or switch off
ignition on vehicles with power
button. Turn the steering wheel
until the steering wheel lock is
felt to engage.
Lock the vehicle with e on the
radio remote control.
Activate the anti-theft alarm
system 3 32.
The engine cooling fans may run
after the engine has been
switched off 3 186.
20
In brief
Caution
After running at high engine
speeds or with high engine loads,
operate the engine briefly at a low
load or run in neutral for
approx. 30 seconds before
switching off, in order to protect
the turbocharger.
Keys, locks 3 21, Laying-up the
vehicle for a long period of time
3 185.
Keys, doors and windows
Keys, doors and
windows
Keys, locks ................................... 21
Keys .......................................... 21
Radio remote control ................. 22
Electronic key system ................ 23
Central locking system .............. 24
Automatic locking ...................... 28
Child locks ................................. 29
Doors ........................................... 30
Load compartment .................... 30
Vehicle security ............................ 31
Anti-theft locking system ........... 31
Anti-theft alarm system .............. 32
Immobiliser ................................ 34
Exterior mirrors ............................ 34
Convex shape ........................... 34
Electric adjustment .................... 34
Folding mirrors .......................... 35
Heated mirrors ........................... 35
Interior mirrors ............................. 36
Manual anti-dazzle .................... 36
Automatic anti-dazzle ................ 36
Windows ...................................... 36
Windscreen ............................... 36
Power windows ......................... 37
Heated rear window .................. 38
Heated windscreen .................... 39
Sun visors .................................. 40
Roof ............................................. 40
Glass panel ............................... 40
21
Keys, locks
Keys
Caution
Do not attach heavy or bulky items
to the ignition key.
Replacement keys
The key number is specified on a
detachable tag.
The key number must be quoted
when ordering replacement keys as it
is a component of the immobiliser
system.
Locks 3 219.
Central locking 3 24.
Starting the engine 3 135.
Radio remote control 3 22.
Electronic key 3 23.
The code number of the adapter for
the locking wheel nuts is specified on
a card. It must be quoted when
ordering a replacement adapter.
Wheel changing 3 212.
22
Keys, doors and windows
Key with foldaway key section
Radio remote control
The remote control has a range of up
to 100 metres, but may also be much
less due to external influences. The
hazard warning flashers confirm
operation.
Handle with care, protect from
moisture and high temperatures and
avoid unnecessary operation.
Replacing battery in radio remote
control
Replace the battery as soon as the
range reduces.
Press button to extend. To fold the
key, first press the button.
Lock cylinders
Designed to free-wheel if they are
forcefully rotated without the correct
key or if the correct key is not fully
inserted. To reset, turn cylinder with
the correct key until its slot is vertical,
remove key then re-insert it. If the
cylinder still free-wheels, turn the key
through 180° and repeat operation.
Enables operation of the following
functions via the use of the remote
control buttons:
● central locking system 3 24
● anti-theft locking system 3 31
● anti-theft alarm system 3 32
● tailgate unlocking 3 24
● power windows 3 37
● mirrors folding
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
Keys, doors and windows
Fault
1. To unclip the cover insert a small
screwdriver between the back
cover and the remote control.
2. Remove the back cover.
3. Extract the flat battery from its
location.
4. Replace battery with a battery of
the same type. Pay attention to
the installation position.
5. Clip the cover in place.
If the central locking system cannot
be operated with the radio remote
control, the cause may be one of the
following:
● Fault in radio remote control.
● The range is exceeded.
● The battery voltage is too low.
● Frequent, repeated operation of
the radio remote control while not
in range, which will require resynchronisation.
● Overload of the central locking
system by operating at frequent
intervals, the power supply is
interrupted for a short time.
● Interference from higher-power
radio waves from other sources.
Manual unlocking 3 24.
23
Electronic key system
Enables a keyless operation of the
following functions:
● central locking system 3 24
● ignition switching on and starting
the engine 3 135
The electronic key simply needs to be
on the driver's person.
Additionally, the electronic key
includes the functionality of the radio
remote control 3 22.
Handle with care, protect from
moisture and high temperatures and
avoid unnecessary operation.
24
Keys, doors and windows
Fault
Replacing battery in electronic
key
Replace the battery as soon as the
system no longer operates properly
or the range is reduced. The need for
battery replacement is indicated by a
message in the Driver Information
Centre 3 101.
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
1. To unclip the cover insert a small
screwdriver in the cutout.
2. Remove the cover.
3. Extract the flat battery from its
location.
4. Replace battery with a battery of
the same type. Pay attention to
the installation position.
5. Clip the cover in place.
If the central locking cannot be
operated or the engine cannot be
started, the cause may be one of the
following:
● Fault in electronic key.
● Electronic key is out of reception
range.
● The battery voltage is too low.
● Overload of the central locking
system by operating at frequent
intervals, the power supply is
interrupted for a short time.
● Interference from higher-power
radio waves from other sources.
To rectify the cause of the fault,
change the position of the electronic
key.
Manual unlocking 3 24.
Central locking system
Unlocks and locks doors, load
compartment and fuel filler flap.
Pull an interior door handle fully to
unlock and open the respective door.
Keys, doors and windows
Notice
In the event of an accident in which
airbags or belt pretensioners are
deployed, the vehicle is
automatically unlocked.
Notice
A short time after unlocking with the
remote control the doors are locked
automatically if no door has been
opened.
Remote control operation
Unlocking
Unlocking mode can be set in the
vehicle personalisation menu in the
Info-Display. Two settings are
selectable:
● All doors, load compartment and
fuel filler flap will be unlocked by
pressing O once.
● Only the driver's door and fuel
filler flap will be unlocked by
pressing O once. To unlock all
doors and load compartment,
press O twice.
Select the relevant setting in the
Vehicle personalisation.
Vehicle personalisation 3 102.
Unlocking the tailgate
Press P longer to unlock the
tailgate only.
Unlocking and opening the tailgate
3 30.
Locking
Close doors, load compartment and
fuel filler flap.
Press O.
25
Press N.
If a door is not closed properly, the
central locking system will not work.
Confirmation
Operation of the central locking
system is confirmed by the hazard
warning flashers.
26
Keys, doors and windows
Electronic key system operation
Unlocking
●
All doors, load compartment and
fuel filler flap will be unlocked by
passing your hand behind any of
the door handles or by pressing
the tailgate touchpad.
● Only the tailgate will be unlocked
by pressing the tailgate
touchpad.
Vehicle personalisation 3 102
Locking
The electronic key must be outside
the vehicle, within a range of approx.
one metre of the relevant door side.
Pass your hand behind any door
handle to unlock the vehicle or press
the tailgate touchpad.
Unlocking mode can be set in the
vehicle personalisation. Three
settings are selectable:
● Only the driver's door will be
unlocked by passing your hand
behind the driver's door handle.
Press with a finger or thumb on one
of the door handles (at the markings)
or press the tailgate touchpad.
All doors, load compartment and fuel
filler flap will be locked.
Keys, doors and windows
The system locks if any door has
been opened and all doors are now
closed.
If the driver's door is not closed
properly, the electronic key remains in
the vehicle or the ignition is not off,
locking will not be permitted and a
warning chime sounds.
If there have been two or more
electronic keys in the vehicle and the
ignition was on once, the doors will be
locked even if just one electronic key
is taken out of the vehicle.
Unlocking and opening the tailgate
The tailgate can be unlocked and
opened by pushing the touchpad
under the tailgate moulding when the
electronic key is in range. The doors
remain locked depending on the
configuration in the vehicle
personalisation.
Load compartment 3 30
Vehicle personalisation 3 102
Operation with buttons on the
electronic key
27
Confirmation
Operation of central locking system is
confirmed by the hazard warning
flashers.
Central locking buttons
Locks or unlocks all doors, the load
compartment and fuel filler flap from
the passenger compartment via a
switch.
The central locking system can also
be operated with the buttons on the
electronic key.
Press O to unlock the driver's door
and the fuel filler flap or all doors, the
fuel filler flap and the tailgate.
Press N to lock the driver's door and
the fuel filler flap or all doors, the fuel
filler flap and the tailgate.
Press P longer to unlock and open
only the tailgate or all doors, the fuel
filler flap and the tailgate.
Remote control operation 3 24.
Press Q to lock. The LED in the button
illuminates.
Press Q again to unlock. The LED in
the button extinguishes.
28
Keys, doors and windows
Operation with the key in case of
a central locking system fault
In case of a fault, e.g. vehicle battery
or remote control/electronic key
battery is discharged, the driver's
door can be locked or unlocked with
the mechanical key.
The other doors can be opened by
pulling the interior handle. The load
compartment and fuel filler flap will
possibly not be unlocked.
By switching on the ignition, the antitheft locking system is deactivated.
Manual locking
Manual unlocking
Electronic key: press and hold the
latch to extract the integral key.
Manually lock the driver's door by
inserting and turning the key in the
lock cylinder.
Manually unlock the driver's door by
inserting and turning the key in the
lock cylinder.
To lock the other doors, first remove
the black cover by inserting a key and
turning clockwise.
Insert key into the recess and move
latch sideways.
Remove key and attach the black
cover.
The fuel filler flap and tailgate are
possibly not locked.
Automatic locking
Automatic locking after driving off
This system allows automatic locking
of the doors as soon as the speed of
the vehicle exceeds 10 km/h.
Keys, doors and windows
If one of the doors or the load
compartment is open, the automatic
central locking does not take place.
This is signalled by the sound of the
locks rebounding, accompanied by
illumination of h in the instrument
panel, an audible signal and the
display of an alert message.
Automatic relock after unlocking
29
Mechanical child locks
This feature automatically locks all
doors, load compartment and fuel
filler flap a short time after unlocking
with the remote control or electronic
key, provided no door has been
opened.
Child locks
9 Warning
Use the child locks whenever
children are occupying the rear
seats.
You can activate or deactivate this
function permanently. With the
ignition on, press Q until an audible
signal starts and a corresponding
message is displayed.
The state of the system stays in
memory when switching off the
ignition.
Turn the red child lock in the rear
doors to the horizontal position by
using a key. The door cannot be
opened from the inside.
To deactivate, turn the child lock to
the vertical position.
30
Keys, doors and windows
Electric child locks
Switching off
Press Ô again. The indicator lamp on
button goes off, accompanied by a
confirmation message. This indicator
lamp remains on while child lock is
switched on.
Doors
Load compartment
Tailgate
Opening
Remotely operated system to prevent
opening of the rear doors using their
interior controls and use of the rear
electric windows.
Switching on
Press Ô. The indicator lamp in the
button comes on, accompanied by a
confirmation message. This indicator
lamp remains on until the child lock is
switched off.
After unlocking, press the touchpad
switch above the licence plate and
open the tailgate.
Keys, doors and windows
Closing
gases, which cannot be seen or
smelled, could enter the vehicle.
This can cause unconsciousness
and even death.
Caution
Use the interior handle.
Do not push the touchpad switch
whilst closing as this will unlock the
tailgate again.
Central locking system 3 24.
General hints for operating
tailgate
9 Danger
Do not drive with the tailgate open
or ajar, e.g. when transporting
bulky objects, since toxic exhaust
Before opening the tailgate, check
overhead obstructions, e.g. a
garage door, to avoid damage to
the tailgate. Always check the
moving area above and behind the
tailgate.
Notice
The installation of certain heavy
accessories onto the tailgate may
affect its ability to remain open.
Notice
At low outside temperatures the
tailgate may not open fully by itself.
In this event, lift the tailgate manually
to its normal end position.
31
Vehicle security
Anti-theft locking system
9 Warning
Do not use the system if there are
people in the vehicle! The doors
cannot be unlocked from the
inside.
The system deadlocks all the doors.
All doors must be closed otherwise
the system cannot be activated.
Unlocking the vehicle disables the
mechanical anti-theft locking system.
This is not possible with the central
locking button.
32
Keys, doors and windows
Activating
●
●
vehicle inclination, e.g. if it is
raised
ignition
Activation
Press N on the radio remote control
twice within five seconds.
Anti-theft alarm system
The anti-theft alarm system is
combined with the central locking
system.
It monitors:
● doors, tailgate, bonnet
● passenger compartment
including adjoining load
compartment
All doors must be closed and the
electronic key of the electronic key
system must not remain in the
vehicle. Otherwise the system cannot
be activated.
● Radio remote control: selfactivated 30 seconds after
locking the vehicle by pressing e
once.
● Electronic key system: selfactivated 30 seconds after
locking the vehicle by pressing
with a finger or thumb on one of
the front door handles at the
markings.
●
●
Radio remote control or
electronic key: directly by
pressing e twice within
five seconds.
Electronic key system with
passive locking enabled: briefly
activated after passive locking
occurs.
Notice
Changes to the vehicle interior such
as the use of seat covers and open
windows, could impair the function
of passenger compartment
monitoring.
Keys, doors and windows
Activation without monitoring of
passenger compartment and
vehicle inclination
33
3. Close doors.
4. Activate the anti-theft alarm
system.
Status message is displayed in the
Driver Information Centre.
Indication
LED in the central locking button
flashes if the anti-theft alarm system
is activated.
Seek the assistance of a workshop in
the event of faults.
Deactivation
Switch off the monitoring of
passenger compartment and vehicle
inclination when animals are being
left in the vehicle, because of high
volume ultrasonic signals or
movements triggering the alarm. Also
switch off when the vehicle is on a
ferry or train.
1. Close tailgate, bonnet, windows.
2. Press o. LED in the button o
illuminates for a maximum of
ten minutes.
Radio remote control: Unlocking the
vehicle by pressing c deactivates the
anti-theft alarm system.
Electronic key system: Unlocking the
vehicle by pressing on one of the front
door handles at the markings
deactivates the anti-theft alarm
system.
The electronic key must be outside
the vehicle, within a range of approx.
one metre of the relevant door side.
The system is not deactivated by
unlocking the driver's door with the
key or with the central locking button
in the passenger compartment.
34
Keys, doors and windows
Alarm
When triggered, the alarm horn
sounds and the hazard warning lights
flash simultaneously. The number
and duration of alarm signals are
stipulated by legislation.
The anti-theft alarm system can be
deactivated by pressing c, by
pressing the switch on the door
handle with electronic key system or
switching on the ignition.
The anti-theft alarm system can be
deactivated by pressing c, by
pressing on one of the front door
handles at the markings with
electronic key system or switching on
the ignition.
A triggered alarm, which has not been
interrupted by the driver, will be
indicated by the hazard warning
lights. They will flash quickly three
times the next time the vehicle is
unlocked with the radio remote
control. Additionally a warning
message is displayed in the Driver
Information Centre after switching on
the ignition.
Vehicle messages 3 101.
If the vehicle's battery is to be
disconnected (e.g. for maintenance
work), the alarm siren must be
deactivated as follows: switch the
ignition on then off, then disconnect
the vehicle's battery within
15 seconds.
Immobiliser
The system is part of the ignition
switch and checks whether the
vehicle is allowed to be started with
the key being used.
The immobiliser is activated
automatically after the key has been
removed from the ignition switch.
Exterior mirrors
Convex shape
The convex exterior mirror on the
driver's side contains an aspherical
area and reduces blind spots. The
shape of the mirror makes objects
appear smaller, which will affect the
ability to estimate distances.
Side blind spot alert 3 168.
Electric adjustment
Notice
Radio Frequency Identification
(RFID) tags may cause interference
with the key. Do not have it placed
near the key when starting the
vehicle.
Notice
The immobiliser does not lock the
doors. You should always lock the
vehicle after leaving it and switch on
the anti-theft alarm system 3 24,
3 32.
Select the relevant exterior mirror by
pushing the mirror button to the left or
right.
Keys, doors and windows
Then swivel the control to adjust the
mirror.
Electric folding
Heated mirrors
Pull mirror button rearwards. Both
exterior mirrors will fold.
Pull mirror button rearwards again to
return both exterior mirrors to their
original position.
If an electrically folded mirror is
manually extended, pulling mirror
button rearwards will only electrically
extend the other mirror.
Operated by pressing b.
Heating works with the engine
running and is switched off
automatically after a short time.
Heated rear window 3 38.
Folding mirrors
For pedestrian safety, the exterior
mirrors will swing out of their normal
mounting position if they are struck
with sufficient force. Reposition the
mirror by applying slight pressure to
the mirror housing.
35
36
Keys, doors and windows
Interior mirrors
Automatic anti-dazzle
Manual anti-dazzle
Windows
Windscreen
Windscreen stickers
Do not attach stickers such as toll
road stickers or similar on the
windscreen in the area of the interior
mirror. Otherwise the detection zone
of the sensor and the view area of the
camera in the mirror housing could be
restricted.
To reduce dazzle, adjust the lever on
the underside of the mirror housing.
Dazzle from following vehicles at
night is automatically reduced.
Windscreen replacement
Caution
If the vehicle has a front-looking
camera sensor for the driver
assistance systems, it is very
important that any windscreen
replacement is performed
accurately according to Vauxhall
specifications. Otherwise, these
systems may not work properly
and there is a risk of unexpected
behaviour and/or messages from
these systems.
Keys, doors and windows
Safety function
Caution
If the window glass encounters
resistance above the middle of the
window during automatic closing, it is
immediately stopped and opened
again.
If the vehicle is equipped with a
Head-up display, it is very
important that any windscreen
replacement is performed
accurately according to Vauxhall
specifications. Otherwise, the
system may not work properly and
the image may look out of focus.
Power windows
9 Warning
Take care when operating the
power windows. Risk of injury,
particularly to children.
If there are children on the rear
seats, switch on the child safety
system for the power windows.
Keep a close watch on the
windows when closing them.
Ensure that nothing becomes
trapped in them as they move.
Switch on ignition to operate power
windows.
37
Override safety function
Operate the switch for the respective
window by pushing to open or pulling
to close.
Pushing or pulling gently to the first
detent: window moves up or down as
long as the switch is operated.
Pushing or pulling firmly to the second
detent then releasing: window moves
up or down automatically with safety
function enabled. To stop movement,
operate the switch once more in the
same direction.
In the event of closing difficulties due
to frost or the like, switch on the
ignition, then pull the switch to the first
detent and hold. The window moves
up without safety function enabled.
To stop movement, release the
switch.
38
Keys, doors and windows
Child safety system for rear
windows
Press V to deactivate rear door
power windows; the LED illuminates.
To activate, press V again.
Operating windows from outside
The windows can be operated
remotely from outside the vehicle.
Initialising the power windows
Press and hold c to open windows.
Press and hold e to close windows.
Release button to stop window
movement.
If the windows are fully opened or
closed, the hazard warning lights will
flash twice.
Overload
If the windows are repeatedly
operated within short intervals, the
window operation is disabled for
some time.
If the windows cannot be closed
automatically (e.g. after
disconnecting the vehicle battery), a
warning message is displayed in the
Driver Information Centre.
Vehicle messages 3 101.
Activate the window electronics as
follows:
1. Close doors.
2. Switch on ignition.
3. Pull switch until the window is
closed and keep pulling for
additional two seconds.
4. Push switch until the window is
completely open and keep
pushing for additional
two seconds.
5. Repeat for each window.
Heated rear window
Operated by pressing b together with
heated exterior mirrors.
Heating works with the engine
running and is switched off
automatically after a short time.
Keys, doors and windows
Depending on climate control system,
b is located at a different position.
Climate Control systems 3 119.
39
Vehicles with electronic climate
control system
Vehicles with electronic climate
control system
Heated windscreen
Vehicles with air conditioning
system
Vehicles with heating and
ventilation system or air
conditioning system
Operated by pressing ,. LED in
button illuminates.
Heating works with the engine
running and is switched off
automatically after a short time.
Depending on climate control
system, , is located at a different
position.
40
Keys, doors and windows
Sun visors
The sun visors can be folded down or
swivelled to the side to prevent
dazzling.
The covers of the mirrors should be
closed when driving.
A ticket holder is located on the
backside of the sun visor.
Roof
Glass panel
Do not affix any stickers to the roof.
Do not cover the vehicle using a
tarpaulin.
Sunblind
The sunblind is electrically operated.
Press N firmly to the second detent
and then release at the rear: the
sunblind is opened as long as the
switch is operated.
Press N gently to the first detent at
the front: the sunblind is closed as
long as the switch is operated.
Press N firmly to the second detent
and then release at the front: the
sunblind is closed as long as the
switch is operated.
Safety function
If the sunblind encounters resistance
during automatic closing, it is
immediately stopped and opened
again.
Function standby
In ignition switch position 1 the
sunblind is operational 3 132.
Press N gently to the first detent at
the rear: the sunblind is opened as
long as the switch is operated.
Initialising after a power failure
After a power failure, it may only be
possible to operate the sunblind to a
limited extent. Initialise the system as
follows:
Keys, doors and windows
1. Turn key in ignition switch to
position 1.
2. Press N twice gently to the first
detent at the rear, the sunblind
opens slightly.
3. Immediately press N twice gently
to the first detent at the front, the
sunblind closes slightly.
After step 3 the sunblind is in
initialising mode without safety
function.
4. Press N gently to the first detent
at the rear until the sunblind is
completely opened.
5. Press N gently to the first detent
at the front until the sunblind is
completely closed.
After this procedure, the sunblind is
initialised with safety function
activated.
When N is pressed firmly to the
second detent during initialising, the
procedure is cancelled.
41
42
Seats, restraints
Seats, restraints
Head restraints
Height adjustment
Position
Head restraints ............................ 42
Front seats ................................... 43
Seat position .............................. 43
Seat adjustment ........................ 44
Armrest ...................................... 46
Heating ...................................... 46
Rear seats ................................... 47
Armrest ...................................... 47
Seat belts ..................................... 48
Three-point seat belt ................. 49
Airbag system .............................. 51
Front airbag system ................... 54
Side airbag system .................... 54
Curtain airbag system ............... 55
Airbag deactivation .................... 56
Child restraints ............................. 57
Child restraint systems .............. 57
Child restraint installation
locations ................................... 60
Head restraints on front seats
9 Warning
Only drive with the head restraint
set to the proper position.
Press release button, adjust height,
engage.
The upper edge of the head restraint
should be at upper head level. If this
is not possible for extremely tall
people, set to highest position, and
set to lowest position for small people.
Seats, restraints
Head restraints on rear seats
Front seats
Height adjustment
Seat position
43
9 Warning
Only drive with the seat correctly
adjusted.
9 Danger
Do not sit closer than 25 cm to the
steering wheel, to permit safe
airbag deployment.
Pull the head restraint upwards or
press the catch to release and push
the head restraint downwards.
●
9 Warning
Never adjust seats while driving as
they could move uncontrollably.
●
Sit with buttocks as far back
against the backrest as possible.
Adjust the distance between the
seat and the pedals so that legs
are slightly angled when fully
pressing the pedals. Slide the
front passenger seat as far back
as possible.
Set seat height high enough to
have a clear field of vision on all
sides and of all display
instruments. There should be at
least one hand of clearance
between head and the roof
frame. Your thighs should rest
lightly on the seat without
pressing into it.
44
Seats, restraints
●
Sit with shoulders as far back
against the backrest as possible.
Set the backrest rake so that it is
possible to easily reach the
steering wheel with arms slightly
bent. Maintain contact between
shoulders and the backrest when
turning the steering wheel. Do
not angle the backrest too far
back. We recommend a
maximum rake of approx. 25°.
Adjust seat and steering wheel in
a way that the wrist rests on top
of the steering wheel while the
arm is fully extended and
shoulders on the backrest.
Adjust the steering wheel 3 74.
Adjust the head restraint 3 42.
Adjust the thigh support so that
there is a space approx. two
fingers wide between the edge of
the seat and the hollow of the
knee.
Adjust the lumbar support so that
it supports the natural shape of
the spine.
●
●
●
●
●
Seat adjustment
Backrest inclination
Drive only with engaged seats and
backrests.
Longitudinal adjustment
Turn handwheel. Do not lean on
backrest when adjusting.
Pull handle, slide seat, release
handle. Try to move the seat back and
forth to ensure that the seat is locked
in place.
Seats, restraints
45
Seat height
Seat inclination
Lumbar support
Lever pumping motion
up
: seat higher
down : seat lower
Press switch
top
: front end higher
bottom : front end lower
Adjust lumbar support using the fourway switch to suit personal
requirements.
Moving support up and down: push
switch up or down.
Increasing and decreasing support:
push switch forwards or backwards.
46
Seats, restraints
Adjustable thigh support
Armrest
Pull the lever and slide the thigh
support.
Armrest can be folded up.
Heating
Adjust heating to the desired setting
by pressing ß for the respective seat
one or more times. The control
indicator in the button indicates the
setting.
Prolonged use of the highest setting
for people with sensitive skin is not
recommended.
Seat heating is operational when
engine is running.
During an Autostop, seat heating is
also operational.
Stop-start system 3 137.
Seats, restraints
Rear seats
Armrest
Longitudinal adjustment
On vehicles with sliding rear seats,
both parts of the rear seat can be
individually moved forwards or
backwards.
9 Warning
Seat backrests must be
completely folded up or down to
have the seats engaged in the
guide rails.
Only drive with the seats engaged
in the guide rails.
Folding backrests 3 65.
9 Warning
Never adjust seats while driving as
they could move uncontrollably.
Pull handle, slide seat, release
handle and allow seat to engage.
The seats can be engaged in
intermediate positions.
The armrest contains cupholders.
Folding down armrest 3 65.
47
48
Seats, restraints
Seat belts
The seat belts are locked during
heavy acceleration or deceleration of
the vehicle, holding the occupants in
the seat position. Therefore the risk of
injury is considerably reduced.
9 Warning
Fasten seat belt before each trip.
In the event of an accident, people
not wearing seat belts endanger
their fellow occupants and
themselves.
Seat belts are designed to be used by
only one person at a time. Child
restraint system 3 57.
Periodically check all parts of the belt
system for damage, soiling and
proper functionality.
Have damaged components
replaced. After an accident, have the
belts and triggered belt pretensioners
replaced by a workshop.
Notice
Make sure that the belts are not
damaged by shoes or sharp-edged
objects or are trapped. Prevent dirt
from getting into the belt retractors.
Seat belt reminder
Each seat is equipped with a seat belt
reminder, indicated by a control
indicator X for the respective seat in
the roof console 3 89.
Belt force limiters
Stress on the body is reduced by the
gradual release of the belt during a
collision.
Belt pretensioners
In the event of a head-on, rear-end or
side-on collision of a certain severity,
the front and rear seat belts are
tightened. The front seat belts are
tightened by two pretensioners per
seat. The outer rear seat belts are
tightened by one pretensioner per
seat.
9 Warning
Incorrect handling (e.g. removal or
fitting of belts) can trigger the belt
pretensioners.
Deployment of the belt pretensioners
is indicated by continuous illumination
of control indicator v 3 90.
Triggered belt pretensioners must be
replaced by a workshop. Belt
pretensioners can only be triggered
once.
Notice
Do not affix or install accessories or
other objects that may interfere with
the operation of the belt
pretensioners. Do not make any
Seats, restraints
49
Unfasten
modifications to belt pretensioner
components as this will invalidate
the operating permit of your vehicle.
Three-point seat belt
Fasten
Loose or bulky clothing prevents the
belt from fitting snugly. Do not place
objects such as handbags or mobile
phones between the belt and your
body.
Withdraw the belt from the retractor,
guide it untwisted across the body
and insert the latch plate into the
buckle. Tighten the lap belt regularly
whilst driving by pulling the shoulder
belt.
9 Warning
The belt must not rest against hard
or fragile objects in the pockets of
your clothing.
Seat belt reminder X 3 89.
To release belt, press red button on
belt buckle.
Centre seat belt of the second
seat row
The centre seat is equipped with a
particular three-point seat belt.
50
Seats, restraints
Pull latch plates with the belt out of
belt holder in the roof.
Insert lower latch plate into left-hand
buckle (1) at the centre seat. Guide
the upper latch plate with the belt over
the lap area and the shoulder (do not
twist) and insert it into right-hand
buckle (2) at centre seat.
To unfasten the seat belt, first press
the button on the right-hand buckle
(2) and remove upper latch plate.
Then press the button on the lefthand buckle (1) and remove lower
latch plate. The seat belt retracts
automatically.
Using the seat belt while pregnant
9 Warning
The lap belt must be positioned as
low as possible across the pelvis
to prevent pressure on the
abdomen.
Seats, restraints
Airbag system
The airbag system consists of a
number of individual systems
depending on the scope of
equipment.
When triggered, the airbags inflate
within milliseconds. They also deflate
so quickly that it is often unnoticeable
during the collision.
9 Warning
The airbag system deploys in an
explosive manner, repairs must be
performed by skilled personnel
only.
9 Warning
Adding accessories that change
the vehicle's frame, bumper
system, height, front end or side
sheet metal, may keep the airbag
system from working properly. The
operation of the airbag system can
also be affected by changing any
parts of the front seats, seat belts,
airbag sensing and diagnostic
module, steering wheel,
instrument panel, inner door seals
including the speakers, any of the
airbag modules, ceiling or pillar
trim, front sensors, side impact
sensors or airbag wiring.
Notice
The airbag systems and belt
pretensioner control electronics are
located in the centre console area.
Do not put any magnetic objects in
this area.
Do not affix any objects onto the
airbag covers and do not cover them
with other materials. Have damaged
covers replaced by a workshop.
Each airbag is triggered only once.
Have deployed airbags replaced by
a workshop. Furthermore, it may be
necessary to have the steering
wheel, the instrument panel, parts of
the panelling, the door seals,
handles and the seats replaced.
Do not make any modifications to
the airbag system as this will
invalidate the vehicle operating
permit.
51
Control indicator v for airbag systems
3 90.
Child restraint systems on front
passenger seat with airbag
systems
Warning according to ECE R94.02:
EN: NEVER use a rearward-facing
child restraint on a seat protected by
an ACTIVE AIRBAG in front of it;
DEATH or SERIOUS INJURY to the
CHILD can occur.
DE: Nach hinten gerichtete
Kindersitze NIEMALS auf einem Sitz
verwenden, der durch einen davor
befindlichen AKTIVEN AIRBAG
52
Seats, restraints
geschützt ist, da dies den TOD oder
SCHWERE VERLETZUNGEN DES
KINDES zur Folge haben kann.
FR: NE JAMAIS utiliser un siège
d'enfant orienté vers l'arrière sur un
siège protégé par un COUSSIN
GONFLABLE ACTIF placé devant lui,
sous peine d'infliger des
BLESSURES GRAVES, voire
MORTELLES à l'ENFANT.
ES: NUNCA utilice un sistema de
retención infantil orientado hacia
atrás en un asiento protegido por un
AIRBAG FRONTAL ACTIVO. Peligro
de MUERTE o LESIONES GRAVES
para el NIÑO.
RU: ЗАПРЕЩАЕТСЯ
устанавливать детское
удерживающее устройство лицом
назад на сиденье автомобиля,
оборудованном фронтальной
подушкой безопасности, если
ПОДУШКА НЕ ОТКЛЮЧЕНА! Это
может привести к СМЕРТИ или
СЕРЬЕЗНЫМ ТРАВМАМ
РЕБЕНКА.
NL: Gebruik NOOIT een achterwaarts
gericht kinderzitje op een stoel met
een ACTIEVE AIRBAG ervoor, om
DODELIJK of ERNSTIG LETSEL van
het KIND te voorkomen.
DA: Brug ALDRIG en bagudvendt
autostol på et forsæde med AKTIV
AIRBAG, BARNET kan komme i
LIVSFARE eller komme ALVORLIGT
TIL SKADE.
SV: Använd ALDRIG en bakåtvänd
barnstol på ett säte som skyddas med
en framförvarande AKTIV AIRBAG.
DÖDSFALL eller ALLVARLIGA
SKADOR kan drabba BARNET.
FI: ÄLÄ KOSKAAN sijoita taaksepäin
suunnattua lasten turvaistuinta
istuimelle, jonka edessä on
AKTIIVINEN TURVATYYNY, LAPSI
VOI KUOLLA tai VAMMAUTUA
VAKAVASTI.
NO: Bakovervendt
barnesikringsutstyr må ALDRI brukes
på et sete med AKTIV
KOLLISJONSPUTE foran, da det kan
føre til at BARNET utsettes for
LIVSFARE og fare for ALVORLIGE
SKADER.
PT: NUNCA use um sistema de
retenção para crianças voltado para
trás num banco protegido com um
AIRBAG ACTIVO na frente do
mesmo, poderá ocorrer a PERDA DE
VIDA ou FERIMENTOS GRAVES na
CRIANÇA.
IT: Non usare mai un sistema di
sicurezza per bambini rivolto
all'indietro su un sedile protetto da
AIRBAG ATTIVO di fronte ad esso:
pericolo di MORTE o LESIONI
GRAVI per il BAMBINO!
EL: ΠΟΤΕ μη χρησιμοποιείτε παιδικό
κάθισμα ασφαλείας με φορά προς τα
πίσω σε κάθισμα που προστατεύεται
από μετωπικό ΕΝΕΡΓΟ ΑΕΡΟΣΑΚΟ,
διότι το παιδί μπορεί να υποστεί
ΘΑΝΑΣΙΜΟ ή ΣΟΒΑΡΟ
ΤΡΑΥΜΑΤΙΣΜΟ.
PL: NIE WOLNO montować fotelika
dziecięcego zwróconego tyłem do
kierunku jazdy na fotelu, przed
którym znajduje się WŁĄCZONA
PODUSZKA POWIETRZNA.
Niezastosowanie się do tego
zalecenia może być przyczyną
ŚMIERCI lub POWAŻNYCH
OBRAŻEŃ u DZIECKA.
Seats, restraints
TR: Arkaya bakan bir çocuk emniyet
sistemini KESİNLİKLE önünde bir
AKTİF HAVA YASTIĞI ile
korunmakta olan bir koltukta
kullanmayınız. ÇOCUK ÖLEBİLİR
veya AĞIR ŞEKİLDE
YARALANABİLİR.
UK: НІКОЛИ не використовуйте
систему безпеки для дітей, що
встановлюється обличчям назад,
на сидінні з УВІМКНЕНОЮ
ПОДУШКОЮ БЕЗПЕКИ, інакше це
може призвести до СМЕРТІ чи
СЕРЙОЗНОГО ТРАВМУВАННЯ
ДИТИНИ.
HU: SOHA ne használjon hátrafelé
néző biztonsági gyerekülést előlről
AKTÍV LÉGZSÁKKAL védett ülésen,
mert a GYERMEK HALÁLÁT vagy
KOMOLY SÉRÜLÉSÉT okozhatja.
HR: NIKADA nemojte koristiti sustav
zadržavanja za djecu okrenut prema
natrag na sjedalu s AKTIVNIM
ZRAČNIM JASTUKOM ispred njega,
to bi moglo dovesti do SMRTI ili
OZBILJNJIH OZLJEDA za DIJETE.
SL: NIKOLI ne nameščajte otroškega
varnostnega sedeža, obrnjenega v
nasprotni smeri vožnje, na sedež z
AKTIVNO ČELNO ZRAČNO
BLAZINO, saj pri tem obstaja
nevarnost RESNIH ali SMRTNIH
POŠKODB za OTROKA.
SR: NIKADA ne koristiti bezbednosni
sistem za decu u kome su deca
okrenuta unazad na sedištu sa
AKTIVNIM VAZDUŠNIM
JASTUKOM ispred sedišta zato što
DETE može da NASTRADA ili da se
TEŠKO POVREDI.
MK: НИКОГАШ не користете детско
седиште свртено наназад на
седиште заштитено со АКТИВНО
ВОЗДУШНО ПЕРНИЧЕ пред него,
затоа што детето може ДА ЗАГИНЕ
или да биде ТЕШКО ПОВРЕДЕНО.
BG: НИКОГА не използвайте
детска седалка, гледаща назад,
върху седалка, която е защитена
чрез АКТИВНА ВЪЗДУШНА
ВЪЗГЛАВНИЦА пред нея - може да
се стигне до СМЪРТ или
СЕРИОЗНО НАРАНЯВАНЕ на
ДЕТЕТО.
RO: Nu utilizaţi NICIODATĂ un scaun
pentru copil îndreptat spre partea din
spate a maşinii pe un scaun protejat
de un AIRBAG ACTIV în faţa sa;
53
acest lucru poate duce la DECESUL
sau VĂTĂMAREA GRAVĂ a
COPILULUI.
CS: NIKDY nepoužívejte dětský
zádržný systém instalovaný proti
směru jízdy na sedadle, které je
chráněno před sedadlem AKTIVNÍM
AIRBAGEM. Mohlo by dojít k
VÁŽNÉMU PORANĚNÍ nebo ÚMRTÍ
DÍTĚTE.
SK: NIKDY nepoužívajte detskú
sedačku otočenú vzad na sedadle
chránenom AKTÍVNYM AIRBAGOM,
pretože môže dôjsť k SMRTI alebo
VÁŽNYM ZRANENIAM DIEŤAŤA.
LT: JOKIU BŪDU nemontuokite atgal
atgręžtos vaiko tvirtinimo sistemos
sėdynėje, prieš kurią įrengta AKTYVI
ORO PAGALVĖ, nes VAIKAS GALI
ŽŪTI arba RIMTAI SUSIŽALOTI.
LV: NEKĀDĀ GADĪJUMĀ
neizmantojiet uz aizmuguri vērstu
bērnu sēdeklīti sēdvietā, kas tiek
aizsargāta ar tās priekšā uzstādītu
AKTĪVU DROŠĪBAS SPILVENU, jo
pretējā gadījumā BĒRNS var gūt
SMAGAS TRAUMAS vai IET BOJĀ.
54
Seats, restraints
ET: ÄRGE kasutage tahapoole
suunatud lapseturvaistet istmel, mille
ees on AKTIIVSE TURVAPADJAGA
kaitstud iste, sest see võib
põhjustada LAPSE SURMA või
TÕSISE VIGASTUSE.
MT: QATT tuża trażżin għat-tfal li
jħares lejn in-naħa ta’ wara fuq sit
protett b’AIRBAG ATTIV quddiemu;
dan jista’ jikkawża l-MEWT jew
ĠRIEĦI SERJI lit-TFAL.
GA: Ná húsáid srian sábháilteachta
linbh cúil RIAMH ar shuíochán a
bhfuil mála aeir ag feidhmiú os a
chomhair. Tá baol BÁIS nó GORTÚ
DONA don PHÁISTE ag baint leis.
Beyond the warning required by
ECE R94.02, for safety reasons a
forward-facing child restraint system
must only be used subject to the
instructions and restrictions in the
table 3 60.
The airbag label is located on both
sides of the front passenger sun visor.
Airbag deactivation 3 56.
Front airbag system
The front airbag system consists of
one airbag in the steering wheel and
one in the instrument panel on the
front passenger side. These can be
identified by the word AIRBAG.
The front airbag system is triggered in
the event of a front-end impact of a
certain severity. The ignition must be
switched on.
9 Warning
Optimum protection is only
provided when the seat is in the
proper position.
Seat position 3 43.
Keep the area in which the airbag
inflates clear of obstructions.
Fit the seat belt correctly and
engage securely. Only then is the
airbag able to protect.
Side airbag system
The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the upper body and head of
the front seat occupants
considerably.
Seats, restraints
The side airbag system consists of an
airbag in each front seat backrest.
This can be identified by the word
AIRBAG.
The side airbag system is triggered in
the event of a side impact of a certain
severity. The ignition must be
switched on.
55
9 Warning
Keep the area in which the airbag
inflates clear of obstructions.
Notice
Only use protective seat covers that
have been approved for the vehicle.
Be careful not to cover the airbags.
Curtain airbag system
The curtain airbag system consists of
an airbag in the roof frame on each
side. This can be identified by the
word AIRBAG on the roof pillars.
The curtain airbag system is triggered
in the event of a side-on impact of a
certain severity. The ignition must be
switched on.
The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the upper body and pelvis in
the event of a side-on collision
considerably.
The inflated airbags cushion the
impact, thereby reducing the risk of
injury to the head in the event of a
side-on impact considerably.
9 Warning
Keep the area in which the airbag
inflates clear of obstructions.
The hooks on the handles in the
roof frame are only suitable for
hanging up light articles of
clothing, without coat hangers. Do
not keep any items in these
clothes.
56
Seats, restraints
Airbag deactivation
The front passenger airbag system
must be deactivated for child restraint
system on the passenger seat
according to the instructions in the
table 3 60. The side airbag and
curtain airbag systems, the belt
pretensioners and all driver airbag
systems will remain active.
Use the ignition key to choose the
position:
*OFF : front passenger airbag is
deactivated and will not
inflate in the event of a
collision. Control indicator
*OFF illuminates
continuously in the centre
console
ÓON : front passenger airbag is
active
9 Danger
The front passenger airbag system
can be deactivated via a keyoperated switch on the passenger
side of the instrument panel.
Deactivate passenger airbag only
in combination with the use of a
child restraint system, subject to
the instructions and restrictions in
the table 3 60.
Otherwise, there is a risk of fatal
injury for a person occupying a
seat with a deactivated front
passenger airbag.
If the control indicator ÓON
illuminates for approx. 60 seconds
after the ignition is switched on, the
front passenger airbag system will
inflate in the event of a collision.
If the control indicator *OFF
illuminates after the ignition is
switched on, the front passenger
airbag system is deactivated. It stays
on while the airbag is deactivated.
If both control indicators are
illuminated at the same time, there is
a system failure. The status of the
system is not discernible, therefore
no person is allowed to occupy the
front passenger seat. Contact a
workshop immediately.
Seats, restraints
Consult a workshop immediately if
neither of the two control indicators
are illuminated.
Change status only when the vehicle
is stopped with the ignition off.
Status remains until the next change.
Control indicator for airbag
deactivation 3 90.
Child restraints
Child restraint systems
9 Danger
If using a rear-facing child restraint
system on the front passenger
seat, the airbag system for the
front passenger seat must be
deactivated. This also applies to
certain forward-facing child
restraint systems as indicated in
the tables 3 60.
Airbag deactivation 3 56.
Airbag label 3 51.
We recommend a child restraint
system which is tailored specifically to
the vehicle. For further information,
contact your workshop.
When a child restraint system is being
used, pay attention to the following
usage and installation instructions
and also those supplied with the child
restraint system.
57
Always comply with local or national
regulations. In some countries, the
use of child restraint systems is
forbidden on certain seats.
Child restraint systems can be
fastened with:
● Three-point seat belt
● ISOFIX brackets
● Top-tether anchor
Three-point seat belt
Child restraint systems can be
fastened by using a three-point seat
belt.
ISOFIX brackets
58
Seats, restraints
Fasten vehicle-approved ISOFIX
child restraint systems to the ISOFIX
brackets. Specific vehicle ISOFIX
child restraint system positions are
marked in the ISOFIX table 3 60.
ISOFIX brackets are indicated by a
label on the backrest.
An i-size child restraint system is an
universal ISOFIX child restraint
system according UN Regulation No.
129.
All i-size child restraint systems can
be used on any vehicle seat suitable
for i-size, i-size table 3 60.
Either a Top-tether strap or a support
leg must be used in addition to the
ISOFIX brackets.
Top-tether anchors
Top-tether anchors are marked with
the symbol : for a child seat.
In addition to the ISOFIX brackets,
fasten the Top-tether strap to the
Top-tether anchors.
ISOFIX child restraint systems of
universal category positions are
marked in the table by IUF 3 60.
Selecting the right system
i-size child seats and vehicle seats
with i-size approval are marked with
i-size symbol, see illustration.
The rear seats are the most
convenient location to fasten a child
restraint system.
Children should travel facing
rearwards in the vehicle as long as
possible. This makes sure that the
child's backbone, which is still very
weak, is under less strain in the event
of an accident.
Suitable are restraint systems that
comply with valid UN ECE
regulations. Check local laws and
regulations for mandatory use of child
restraint systems.
The following child restraints are
recommended for the following
weight classes:
● Maxi Cosi Cabriofix for group 0,
group 0+
● Duo Plus for group I
● Kidfix XP for group II/III
● Graco Junior for group III
Ensure that the child restraint system
to be installed is compatible with the
vehicle type.
Ensure that the mounting location of
the child restraint system within the
vehicle is correct, see following
tables.
Seats, restraints
Allow children to enter and exit the
vehicle only on the side facing away
from the traffic.
When the child restraint system is not
in use, secure the seat with a seat belt
or remove it from the vehicle.
Notice
Do not affix anything on the child
restraint systems and do not cover
them with any other materials.
A child restraint system which has
been subjected to stress in an
accident must be replaced.
59
60
Seats, restraints
Child restraint installation locations
Permissible options for fastening a child restraint system with a three-point seat belt
On front passenger seat
Weight class
activated airbag
deactivated airbag
On rear outboard seats
On rear centre seat
Group 0: up to 10 kg
X
U1,2
U/L3
X
Group 0+: up to 13 kg
X
U1,2
U/L3
X
Group I: 9 to 18 kg
X
U1,2
U/L3,4
X
Group II: 15 to 25 kg
U1,2
X
U/L3,4
X
Group III: 22 to 36 kg
U1,2
X
U/L3,4
X
U : universal suitability in conjunction with three-point seat belt
L : suitable for particular child restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories. The
child restraint system must be approved for the specific vehicle type (refer to the vehicle type list of the child restraint
system)
X : no child restraint system permitted in this weight class
1 : move seat forwards as far as necessary and adjust seat backrest inclination as far as necessary to a vertical position
to ensure that the belt runs forwards from the upper anchorage point
2 : move seat height adjustment upwards as far as necessary and adjust seat backrest inclination as far as necessary
to a vertical position to ensure that the belt is tight on the buckle side
3 : move the respective front seat ahead of the child restraint system forwards and the sliding rear seat backwards as
far as necessary
4 : adjust the respective headrest as necessary or remove if required
Seats, restraints
61
Permissible options for fitting an ISOFIX child restraint system with ISOFIX brackets
On front passenger seat
Weight class
Size class Fixture
On rear outboard
activated airbag deactivated airbag seats
On rear centre
seat
Group 0: up to 10 kg
G
ISO/L2
X
X
X
X
F
ISO/L1
X
X
X
X
E
ISO/R1 X
X
IL1
X
Group 0+: up to 13 kg E
ISO/R1 X
X
IL1
X
D
ISO/R2 X
X
IL1
X
C
ISO/R3 X
X
IL1
X
D
ISO/R2 X
X
IL1,2
X
C
ISO/R3 X
X
IL1,2
X
B
ISO/F2
X
B1
A
Group I: 9 to 18 kg
X
IL,
IUF1,2
X
ISO/F2X X
X
IL, IUF1,2
X
ISO/F3
X
X
IL, IUF1,2
X
Group II: 15 to 25 kg
X
X
IL1,2
X
Group III: 22 to 36 kg
X
X
IL1,2
X
62
IL
Seats, restraints
: suitable for particular ISOFIX restraint systems of the 'specific-vehicle', 'restricted' or 'semi-universal' categories.
The ISOFIX restraint system must be approved for the specific vehicle type (refer to the vehicle type list of the child
restraint system)
IUF : suitable for ISOFIX forward-facing child restraint systems of universal category approved for use in this weight class
X : no ISOFIX child restraint system approved in this weight class
1
: move the respective front seat ahead of the child restraint system forwards and the sliding rear seat backwards as
far as necessary
2
: adjust the respective headrest as necessary or remove if required
C – ISO/R3
: rear-facing child
F– ISO/L1
: left lateral facing
ISOFIX size class and seat device
restraint system
position child
A – ISO/F3
: forward-facing
for children of
restraint system
child restraint
maximum size in
(carry-cot)
system for
the weight class
G – ISO/L2
: right lateral facing
children of
up to 18 kg
position child
maximum size in
D – ISO/R2
: rear-facing child
restraint system
the weight class
restraint system
(carry-cot)
9 to 18 kg
for smaller
B – ISO/F2
: forward-facing
children in the
child restraint
weight class up to
system for smaller
18 kg
children in the
E – ISO/R1
: rear-facing child
weight class
restraint system
9 to 18 kg
for young children
B1 – ISO/F2X : forward-facing
in the weight class
child restraint
up to 13 kg
system for smaller
children in the
weight class
9 to 18 kg
Seats, restraints
63
Permissible options for fitting an i-Size child restraint system with ISOFIX brackets
On front passenger seat
i-Size child restraint systems
activated airbag
deactivated airbag
On rear outboard seats
On rear centre seat
X
X
i-U
X
i - U : suitable for i-Size 'universal' forward and rearward facing child restraint systems
X
: seating position not suitable for i-Size 'universal' child restraint systems
64
Storage
Storage
Storage compartments ................ 64
Glovebox ................................... 64
Cupholders ................................ 64
Centre console storage ............. 65
Load compartment ....................... 65
Load compartment cover ........... 68
Rear floor storage cover ............ 68
Lashing eyes ............................. 69
Warning triangle ........................ 70
First aid kit ................................. 70
Roof rack system ......................... 71
Roof rack ................................... 71
Loading information ..................... 71
Storage compartments
9 Warning
Do not store heavy or sharp
objects in the storage
compartments. Otherwise, the
storage compartment lid could
open and vehicle occupants could
be injured by objects being thrown
around in the event of hard
braking, a sudden change in
direction or an accident.
On some versions the glovebox is
ventilated. Air ventilation and
temperature depend on the settings
of the climate control system. The air
vent in the glove box can be closed
3 128.
Other versions may have a CD player
in the glove box.
The glovebox should be closed whilst
driving.
Cupholders
Glovebox
Cupholders are located in the centre
console.
Storage
65
Load compartment
Additional cupholders are located in
the rear armrest. Fold down armrest.
Centre console storage
Depending on the version, the
storage compartment is located
under a cover.
The rear seat backrest is divided in
two parts. Both parts can be folded
down.
Before folding rear seat backrests,
execute the following if necessary:
● Remove the load compartment
cover 3 68.
● Press and hold the catch to push
the head restraints down 3 42.
Load compartment extension
(version with fixed rear seats)
The storage container can be used to
store small items.
●
Pull the release lever on one or
both outer sides and fold down
66
Storage
Load compartment extension
(version with sliding rear seats)
the backrests onto the seat
cushion.
Without folding backrests
Move both rear seats to the most
forward position 3 47.
With folding backrests
● Move both rear seats to the most
rearward position 3 47.
●
When folding the backrests,
insert the seat belts in the guiding
latches and pull the seat belts
along with them.
To fold up, raise the backrests
and guide them into an upright
position until they engage
audibly.
The backrests are properly
engaged when the red mark near
the release lever is no longer
visible.
9 Warning
When folding up, ensure that
backrests are securely locked in
position before driving. Failure to
do so may result in personal injury
or damage to the load or vehicle in
the event of hard braking or a
collision.
●
Pull the loop and fold down the
backrest onto the seat cushion.
Storage
Folding the armrest in the rear
centre backrest
To fold down the backrest from
the load compartment, lift the
release lever.
Notice
Fold up the armrest before folding
down the relevant part of the
backrest. Otherwise this part of the
backrest can not be folded down.
●
When folding the backrests,
insert the seat belts in the guiding
latches and pull the seat belts
along with them.
To fold up, raise the backrests
and guide them into an upright
position until they engage
audibly.
Pull the loop to fold down the rear
armrest.
67
68
Storage
The armrest can also be folded down
from the rear by pulling the loop.
Suitable for loading long, narrow
objects.
Ensure that the armrest engages
after folding up.
The load compartment cover can be
stored behind the rear seat backrests.
Unhook retaining straps and lift the
cover backwards until it unlatches.
Then slide it down in the guides
behind the seat backrests.
Fitting cover
Load compartment cover
Engage cover in side guides and fold
downwards. Attach the retaining
straps to the tailgate.
Do not place any objects on the cover.
Removing cover
Lift cover, slightly angle and turn it.
Remove the cover.
Rear floor storage cover
Stowing
Unhook retaining straps from tailgate.
The rear floor cover can be removed.
Raise cover at the recess and
remove.
Storage
69
Lashing eyes
The cover can also be stored behind
the rear seats.
Double load floor
The double load floor can be inserted
in the load compartment in two
positions:
●
●
lower position above the spare
wheel well cover
upper position interlocked with
the grab handle into back panel
trim
To remove, press the handle to
unlock the load floor and lift it up while
using the handle.
If mounted in the upper position, the
space between the load floor and the
spare wheel well cover can be used
as a storage compartment.
In this position, if the rear seat
backrests are folded forwards, an
almost completely flat load bay is
created.
In the upper position, the double load
floor is able to withstand a maximum
load of 100 kg. In the lower position,
the double load floor is able to
withstand the maximum permissible
load.
The lashing eyes are designed to
secure items against slippage, e.g.
using lashing straps or luggage net.
70
Storage
Warning triangle
First aid kit
Stow the warning triangle in the space
at the rear of the load compartment
and secure it with the velcro fastener.
Fold down the cover on the left side
of the load compartment.
Stow the first aid kit in the stowage
compartment.
Storage
Roof rack system
Roof rack
Detach the cover from each mounting
point and fasten the roof rack with the
attached screws.
71
Loading information
For safety reasons and to avoid
damage to the roof, the vehicleapproved roof rack system is
recommended.
Follow the installation instructions
and remove the roof rack when not in
use.
Mounting roof rack
●
Open all doors.
Mounting points are located in each
door frame of the vehicle body.
●
Heavy objects in the load
compartment should be placed
against the seat backrests. Make
sure that the backrests are
securely engaged, i.e. no longer
showing the red marks on the
side near the release lever or on
the loop. If objects can be
stacked, heavier objects should
be placed at the bottom.
Secure objects with lashing
straps attached to lashing eyes
3 69.
72
●
●
●
●
●
●
Storage
Secure loose objects in the load
compartment to prevent from
sliding.
When transporting objects in the
load compartment, the backrests
of the rear seats must not be
angled forward.
Do not allow the load to protrude
above the upper edge of the
backrests.
Do not place any objects on the
load compartment cover or the
instrument panel, and do not
cover the sensor on top of the
instrument panel.
The load must not obstruct the
operation of the pedals, parking
brake and gear selector, or
hinder the freedom of movement
of the driver. Do not place any
unsecured objects in the interior.
Do not drive with an open load
compartment.
9 Warning
Always make sure that the load in
the vehicle is securely stowed.
Otherwise objects can be thrown
around inside the vehicle and
cause personal injury or damage
to the load or car.
●
●
The payload is the difference
between the permitted gross
vehicle weight (see identification
plate 3 227) and the EC kerb
weight.
To calculate the payload, enter
the data for your vehicle in the
weights table at the front of this
manual.
The EC kerb weight includes
weights for the driver (68 kg),
luggage (7 kg) and all fluids (fuel
tank 90% full).
Optional equipment and
accessories increase the kerb
weight.
Driving with a roof load increases
the sensitivity of the vehicle to
cross-winds and has a
detrimental effect on vehicle
handling due to the vehicle's
higher centre of gravity.
Distribute the load evenly and
secure it properly with retaining
straps. Adjust the tyre pressure
and vehicle speed according to
the load conditions. Check and
retighten the straps frequently.
Do not drive faster than 75 mph.
The permissible roof load is
60 kg. The roof load is the
combined weight of the roof rack
and the load.
Instruments and controls
Instruments and
controls
Controls ....................................... 74
Steering wheel adjustment ........ 74
Steering wheel controls ............. 74
Heated steering wheel ............... 74
Horn ........................................... 75
Windscreen wiper/washer ......... 75
Rear window wiper/washer ....... 77
Outside temperature .................. 77
Clock ......................................... 78
Power outlets ............................. 78
Inductive charging ..................... 79
Cigarette lighter ......................... 80
Ashtrays .................................... 80
Warning lights, gauges and indi‐
cators ........................................... 81
Instrument cluster ...................... 81
Speedometer ............................. 84
Odometer .................................. 85
Trip odometer ............................ 85
Tachometer ............................... 85
Fuel gauge ................................ 86
Fuel selector .............................. 86
Engine coolant temperature
gauge ....................................... 87
Engine oil level monitor ............. 88
Service display .......................... 88
Control indicators ...................... 89
Turn signal ................................. 89
Seat belt reminder ..................... 89
Airbag and belt tensioners ......... 90
Airbag deactivation .................... 90
Charging system ....................... 90
Malfunction indicator light .......... 90
Service vehicle soon ................. 91
Stop engine ............................... 91
System check ............................ 91
Brake and clutch system ........... 91
Antilock brake system (ABS) ..... 91
Gear shifting .............................. 92
Lane departure warning ............ 92
Electronic Stability Control and
Traction Control system ........... 92
Electronic Stability Control and
Traction Control system off ...... 92
Engine coolant temperature ...... 92
Preheating ................................. 93
Diesel particle filter .................... 93
AdBlue ....................................... 93
Deflation detection system ........ 93
Engine oil pressure .................... 93
Low fuel ..................................... 94
Autostop .................................... 94
Exterior light .............................. 94
High beam ................................. 94
73
High beam assist ....................... 94
Low beam .................................. 94
Fog light ..................................... 94
Rear fog light ............................. 94
Rain sensor ............................... 94
Cruise control ............................ 94
Speed limiter ............................. 95
Traffic sign assistant .................. 95
Door open .................................. 95
Information displays ..................... 95
Driver Information Centre .......... 95
Info display ................................ 97
Head-up display ........................ 99
Vehicle messages ...................... 101
Warning chimes ....................... 101
Battery voltage ........................ 101
Vehicle personalisation .............. 102
Telematics service ..................... 105
OnStar ..................................... 105
74
Instruments and controls
Controls
Heated steering wheel
Steering wheel adjustment
Driver assistance systems 3 151.
Further information is available in the
Infotainment manual.
Unlock lever, adjust steering wheel,
then engage lever and ensure it is
fully locked.
Do not adjust steering wheel unless
vehicle is stationary and steering
wheel lock has been released.
Steering wheel controls
Some driver assistance systems,
Infotainment system and a connected
mobile phone can be operated via the
controls on the steering wheel.
Activate heating by pressing *.
Activation is indicated by the LED in
the button.
Instruments and controls
The recommended grip areas of the
steering wheel are heated quicker
and to a higher temperature than the
other areas.
Heating is operational when the
engine is running and during an
Autostop.
Stop-start system 3 137.
Windscreen wiper/washer
75
Adjustable wiper interval
Windscreen wiper with adjustable
wiper interval
Horn
HI
LO
INT
OFF
Press j.
:
:
:
:
fast
slow
interval wiping
off
For a single wipe when the
windscreen wiper is off, press the
lever downwards to position 1x.
Do not use if the windscreen is frozen.
Switch off in car washes.
Wiper lever in position INT.
Turn the adjuster wheel to adjust the
wiping frequency.
76
Instruments and controls
Windscreen wiper with rain
sensor
HI
: fast
LO
: slow
AUTO : automatic wiping with rain
sensor
OFF : off
In AUTO position, the rain sensor
detects the amount of water on the
windscreen and automatically
regulates the frequency of the
windscreen wiper.
For a single wipe when the
windscreen wiper is off, press the
lever downwards to position 1x.
Do not use if the windscreen is frozen.
Switch off in car washes.
Adjustable sensitivity of the rain
sensor
Keep the sensor free from dust, dirt
and ice.
Control indicator < 3 75.
Wiper lever in position AUTO.
Turn the adjuster wheel to adjust the
sensitivity of the rain sensor.
Windscreen washer
Instruments and controls
Pull lever. Washer fluid is sprayed
onto the windscreen and the wiper
wipes a few times.
Washer fluid 3 188.
Rear window wiper/washer
Rear window wiper
Turn outer cap to activate the rear
window wiper:
OFF : off
INT : intermittent operation
ON : continuous operation
Do not use if the rear window is
frozen.
Switch off in car washes.
The rear window wiper comes on
automatically when the windscreen
wiper is switched on and reverse gear
is engaged.
Activation or deactivation of this
function can be changed in the
Vehicle personalisation menu 3 102.
77
The rear window washer system is
deactivated when the fluid level is
low.
Washer fluid 3 188.
Outside temperature
Rear window washer
A drop in temperature is indicated
immediately and a rise in temperature
after a time delay.
Push lever.
Washer fluid is sprayed onto the rear
window and the wiper wipes a few
times.
Illustration shows an example.
If outside temperature drops to 3 °C,
a warning message is displayed in the
Driver Information Centre.
78
Instruments and controls
9 Warning
A 12 Volt power outlet is located in the
centre console.
The road surface may already be
icy even though the display
indicates a few degrees above 0
°C.
Do not connect any current-delivering
accessories, e.g. electrical charging
devices or batteries.
Do not damage the outlets by using
unsuitable plugs.
Stop-start system 3 137.
USB charging port
Clock
Date and time are shown in the
Info-Display 3 97.
Setting date and time, see
Infotainment manual.
Power outlets
Another power outlet is located in the
console between the front seats.
Do not exceed the maximum power
consumption of 120 watts.
With ignition off, the power outlet is
deactivated. Additionally, the power
outlet is deactivated in the event of
low vehicle battery voltage.
Electrical accessories that are
connected must comply with the
electromagnetic compatibility
requirements laid down in
DIN VDE 40 839.
One or two USB ports are located in
the centre console. Both USB ports
are prepared for charging devices.
When two USB ports are avilable, the
upper USB port can be used to
connect a phone for phone projection.
Instruments and controls
Notice
The sockets must always be kept
clean and dry.
Inductive charging
9 Warning
Inductive charging can affect the
operation of implanted
pacemakers or other medical
devices. If applicable, seek
medical advice before using the
inductive charging device.
9 Warning
Remove any metal objects from
the charging device before
charging a mobile phone, as these
objects could become very hot.
To charge a device, the ignition must
be switched on.
LED status on the charging device
(see arrow):
● Illuminates green:
- mobile phone with inductive
charging functionality was
recognised.
● Illuminates yellow:
- metall objects have been
detected in the charging area.
Remove objects to allow
charging.
- mobile phone was not placed
properly.
79
PMA or Qi compatible mobile phones
can be charged inductively.
A back cover with an integrated coil
(e.g. Samsung 4 and 5) or a jacket
(e.g. some iPhone models) may be
required to charge a mobile phone.
The mobile phone must be smaller
than 8 cm in width and 15 cm in length
to fit into the charging device.
Protective cover for the mobile phone
could have impact on the inductive
charging.
To charge a mobile phone:
1. Remove all objects from the
charging device.
2. Place the mobile phone with the
display facing upwards on the
charging device.
3. Ensure that the mobile phone is
located at the right bottom corner
of the charging device.
In the case that the yellow LED
illuminates:
1. Remove the mobile phone from
the charging device.
2. Rotate the mobile phone by 180°.
80
Instruments and controls
3. Wait three seconds after the LED
has extinguished and place the
mobile phone on the charging
device again.
4. Ensure that the mobile phone is
located at the right bottom corner
of the charging device.
Ashtrays
Caution
To be used only for ash and not for
combustible rubbish.
Cigarette lighter
A portable ashtray can be placed in
the cupholders.
The cigarette lighter is located is
located behind the storage cover
below the climate controls. Press
cover to open.
Press in cigarette lighter. It switches
off automatically once the element is
glowing. Pull out lighter.
Instruments and controls
Warning lights, gauges
and indicators
Instrument cluster
Depending on the version, two
instrument clusters are available:
81
82
Instruments and controls
Baselevel instrument cluster
Instruments and controls
Midlevel instrument cluster
83
84
Instruments and controls
Overview
b
Electronic Stability Control
and Traction Control system
3 92
f
High beam assist 3 94
>
Fog light 3 94
Electronic Stability Control
and Traction Control system
off 3 92
ø
Rear fog light 3 94
<
Rain sensor 3 94
B
Side blind spot alert 3 168
m
Cruise control 3 94
ß
Speed limiter 3 95
L
Traffic sign assistant 3 95
h
Door open 3 95
O
Turn signal 3 89
X
Seat belt reminder 3 89
v
Airbag and belt tensioners
3 90
V
Airbag deactivation 3 90
!
Preheating 3 93
p
Charging system 3 90
%
Diesel particle filter 3 93
Z
Malfunction indicator light
3 90
Y
AdBlue 3 93
w
Deflation detection system
3 93
I
Engine oil pressure 3 93
Engine oil level monitor
3 88
Yo
Low fuel 3 94
Wo
Engine coolant temperature
high 3 92
D
Autostop 3 94
8
Exterior light 3 94
9
Low beam 3 94
C
High beam 3 94
H
a
Service vehicle soon 3 91
STOP Stop engine 3 91
J
System check 3 91
R
Brake and clutch system
3 91
u
Antilock brake system (ABS)
3 91
R
Gear shifting 3 92
)
Lane departure warning
3 92
Speedometer
Instruments and controls
85
Tachometer
Indicates vehicle speed.
Odometer
The total recorded distance is
displayed in miles.
Trip odometer
The recorded distance since the last
reset is displayed in the Driver
Information Centre.
Trip odometer counts up to
9,999 miles and then restarts at 0.
Press L for 2 seconds to reset trip
odometer.
Two trip odometer pages are
selectable in the trip/fuel information
menu for different trips 3 95.
Displays the engine speed.
Drive in a low engine speed range for
each gear as much as possible.
Caution
If the needle is in the red warning
zone, the maximum permitted
engine speed is exceeded. Engine
at risk.
86
Instruments and controls
Fuel gauge
Displays the fuel level in the tank.
Control indicator o illuminates if the
level in the tank is low.
Never run the fuel tank dry.
Because of the fuel remaining in the
tank, the top-up quantity may be less
than the specified fuel tank capacity.
Fuel selector
Liquid gas operation, LPG
LED off
LED
flashes
: petrol operation
: checking conditions for
fuel transition to liquid
gas operation.
Illuminates if conditions
are fulfilled.
LED illu‐ : liquid gas operation
minates
LED
: liquid gas tank is empty
flashes 5 or failure in liquid gas
times
system. A message is
and
displayed in the Driver
extin‐
Information Centre.
guishes
Pressing LPG switches between
petrol and liquid gas operation as
soon as the required parameters
(coolant temperature, gas
temperature and minimum engine
speed) have been reached. The
requirements are usually fulfilled after
approximately 60 seconds
(depending on exterior temperature)
and the first firm press on the
accelerator. The status LED shows
the current operating mode.
If the fuel tank is empty, the engine
will not start.
The selected fuel mode is stored and
reactivated at the next ignition cycle if
conditions allow.
As soon as the liquid gas tank is
empty, petrol operation is
automatically engaged until the
ignition is switched off.
When switching automatically
between petrol or gas operation, a
brief delay of engine tractive power
may be noticeable.
Instruments and controls
Every six months, run the petrol tank
down until control indicator Y
illuminates, then refuel. This helps
maintain fuel quality and system
function for petrol operation.
Fill the tank completely at regular
intervals to prevent corrosion in the
tank.
Faults and remedies
If gas mode is not possible, check the
following:
● Is there enough liquid gas
present?
● Is there enough petrol present for
starting?
Due to extreme temperatures in
combination with the gas
composition, it may take slightly
longer before the system switches
from petrol to gas mode.
In extreme situations, the system may
also switch back to petrol mode if the
minimum requirements are not
fulfilled. If conditions allow, it may be
possible to manually switch back to
liquid gas operation.
Seek the assistance of a workshop in
the event of all other faults.
Caution
Repairs and adjustments may only
be made by trained specialists in
order to maintain the safety and
warranty on the LPG system.
87
Notice
In the event of an accident, switch off
the ignition and lights.
Fuel for liquid gas operation 3 177.
Engine coolant temperature
gauge
Liquid gas is given a particular odour
(odorised) so that any leaks can be
detected easily.
9 Warning
If you smell gas in the vehicle or in
the immediate vicinity, switch to
petrol mode immediately. No
smoking. No naked flames or
ignition sources.
If the gas odour persists, do not start
the engine. Have the cause of the
fault remedied by a workshop.
When using underground car parks,
follow the instructions of the operator
and local laws.
Displays the coolant temperature.
50 : engine operating temperature
not yet reached
90 : normal operating temperature
130 : temperature too high
Control indicator o illuminates if
engine coolant temperature is too
high.
88
Instruments and controls
Caution
If engine coolant temperature is
too high, stop vehicle, switch off
engine. Danger to engine. Check
coolant level.
Engine oil level monitor
The state of the engine oil level is
displayed in the Driver Information
Centre for a few seconds following
the service information after switching
on the ignition.
A proper state of oil level is indicated
by the message Oil level correct.
If oil level is low, I flashes and Oil
level incorrect is indicated,
accompanied by the H indicator.
Confirm oil level by using the oil
dipstick and top up engine oil
respectively. Engine oil 3 187.
A fault of measurment is indicated by
the message Oil level measurment
invalid. Check oil level manually by
using the dipstick.
Service display
The service system informs when to
change the engine oil and filter or a
vehicle service is required. Based on
driving conditions, the interval at
which an engine oil and filter change
is required can vary considerably.
Service information3 223
If service due is required within the
next 3000 km, the remaining distance
or time duration is indicated for
several seconds. Simultaneously
symbol F lights up permamently as
reminder.
If service due is less than 1000 km,
F flashes and then lights up
permanently. Remaining distance or
time duration is indicated for several
seconds.
Overdued service is indicated by a
message in the Driver Information
Centre which indicates the overdued
distance. F flashes and then lights up
permanently until service is executed.
Reset of service interval
A required service due is displayed in
the Driver Information Centre for
seven seconds after switching on the
ignition.
If no service is required for the next
3000 km or more, no service
information appears in the display.
After each service, the service
indicator must be reset to ensure
proper functionality. It is
recommended to seek the assistance
of a workshop.
If service is executed by yourself,
operate as following:
● switch off ignition
● press and hold button M or
CHECK
Instruments and controls
●
●
switch on ignition; the distance
indication begins a countdown
when the display indicates =0,
release the button. Symbol F
disappears
blue : confirmation of activation
white : confirmation of activation
See all control indicators on different
instrument clusters 3 81.
Retrieving service information
Turn signal
To retrieve the status of the service
information at any time press button
M or CHECK. The service
information is displayed for a few
seconds.
Service information 3 223.
O illuminates or flashes green.
Control indicators
The control indicators described are
not present in all vehicles. The
description applies to all instrument
versions. Depending on the
equipment, the position of the control
indicators may vary. When the
ignition is switched on, most control
indicators will illuminate briefly as a
functionality test.
The control indicator colours mean:
red
: danger, important reminder
yellow : warning, information, fault
green : confirmation of activation
89
Seat belt reminder
Seat belt reminder on all seats
X illuminates or flashes red in the
instrument cluster together with the
indication in the roof console for each
seat belt.
Illuminates briefly
The parking lights are switched on.
Flashes
A turn signal or the hazard warning
flashers are activated.
Rapid flashing: failure of a turn signal
light or associated fuse, failure of turn
signal light on trailer.
Bulb replacement 3 191, Fuses
3 199.
Turn signals 3 114.
●
When the ignition is switched on,
X in the instrument cluster and
the symbol for the respective
seat in the roof console comes
90
●
Instruments and controls
on, if the seat belt of any
occupied seat has not been
fastened.
After running up, X in the
instrument cluster and the
symbol for the respective seat in
the roof console flashes for a
certain time together with a
chime. After a certain time of
driving X illuminates constantly
until the seat belt of the
respective seat has been
fastened or if any passenger has
unfastened the seat belt.
Deployment of the belt pretensioners
or airbags is indicated by continuous
illumination of v.
9 Warning
Have the cause of the fault
remedied immediately by a
workshop.
Belt pretensioners, airbag system
3 48, 3 51.
Airbag deactivation
Airbag and belt tensioners
v illuminates red.
When the ignition is switched on, the
control indicator illuminates for
approx. four seconds. If it does not
illuminate, does not go out after
four seconds or illuminates whilst
driving, there is a fault in the airbag
system. Seek the assistance of a
workshop. The airbags and belt
pretensioners may fail to trigger in the
event of an accident.
The front passenger airbag is
activated.
*OFF illuminates yellow.
The front passenger airbag is
deactivated.
Airbag deactivation 3 56.
Charging system
p illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Stop, switch off engine. Vehicle
battery is not charging. Engine
cooling may be interrupted. The
brake servo unit may cease to be
effective. Seek the assistance of a
workshop.
Malfunction indicator light
Z illuminates or flashes yellow.
ÓON illuminates yellow.
Instruments and controls
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Fault in the emission control system.
The permitted emission limits may be
exceeded.
Seek the assistance of a workshop
immediately.
Flashes when the engine is
running
The engine management system has
a fault that could lead to catalytic
converter damage. Ease up on the
accelerator until the flashing stops.
Seek the assistance of a workshop
immediately.
Service vehicle soon
H illuminates yellow.
Illuminates briefly when the ignition is
switched on.
May illuminate together with other
control indicators and a
corresponding message in the Driver
Information Centre.
Seek the assistance of a workshop
immediately.
Illuminates red
Stop engine
Brake and clutch system
Y illuminates red.
Illuminates briefly when the ignition is
switched on.
Illuminates together with other control
indicators, accompanied by a warning
chime and a corresponding message
in the Driver Information Centre.
Stop engine immediately and seek
the assistance of a workshop.
System check
J illuminates yellow or red.
Illuminates yellow
A minor engine fault has been
detected.
91
A major engine fault has been
detected.
Stop engine as soon as possible and
seek the assistance of a workshop.
R illuminates red.
The brake and clutch fluid level is too
low, when manual parking brake is
not applied 3 189.
9 Warning
Stop. Do not continue your
journey. Consult a workshop.
Illuminates when the manual parking
brake is applied and ignition is
switched on 3 148.
Antilock brake system
(ABS)
u illuminates yellow.
92
Instruments and controls
Illuminates for a few seconds after the
ignition is switched on. The system is
ready for operation when the control
indicator extinguishes.
If the control indicator does not go out
after a few seconds, or if it illuminates
while driving, there is a fault in the
ABS. The brake system remains
operational but without ABS
regulation.
Antilock brake system 3 148.
Gear shifting
R with the number of a higher gear is
indicated, when upshifting is
recommended for fuel saving
reasons.
Lane departure warning
) flashes yellow when the system
recognises an unintended lane
change.
Lane departure warning 3 173.
Electronic Stability Control
and Traction Control system
b illuminates or flashes yellow.
Flashes
The system is actively engaged.
Engine output may be reduced and
the vehicle may be braked
automatically to a small degree.
Electronic Stability Control and
Traction Control system 3 149.
Electronic Stability Control
and Traction Control system
off
n illuminates yellow.
The systems are deactivated.
Illuminates
Engine coolant temperature
A fault in the system is present.
Continued driving is possible. Driving
stability, however, may deteriorate
depending on road surface
conditions.
Have the cause of the fault remedied
by a workshop.
o illuminates red.
Illuminates when the engine is
running
Stop, switch off engine.
Caution
Coolant temperature too high.
Instruments and controls
Check coolant level immediately
3 188.
If there is sufficient coolant, consult a
workshop.
Preheating
! illuminates yellow.
Preheating of Diesel engine is
activated. Only activates when
outside temperature is low. Start the
engine when control indicator
extinguishes.
Diesel particle filter
% or H illuminates yellow.
The diesel particle filter requires
cleaning.
Continue driving until the control
indicator extinguishes.
Illuminates temporarily
Start of saturation of the particle filter.
Start cleaning process as soon as
possible by driving at a vehicle speed
of at least 40 mph.
93
Illuminates constantly
Illuminates
Indication of a low additive level. Seek
the assistance of a workshop.
Diesel particle filter 3 140.
Tyre pressure loss in one or more
wheels. Stop immediately and check
tyre pressure.
AdBlue
Y flashes or illuminates yellow.
Illuminates yellow
The remaining driving range is
between 600 km and 2400 km.
Have the AdBlue® topped-up as soon
as possible by a qualified workshop.
You can add up to 10 litres of
AdBlue® to its tank.
Flashes yellow
The remaining driving range is
between 0 and 600 km.
Top-up the AdBlue® as soon as
possible to avoid a breakdown by a
qualified workshop. You can add up
to 10 litres of AdBlue® to its tank.
Deflation detection system
w illuminates or flashes yellow.
Flashes
Fault in system. Consult a workshop.
Engine oil pressure
I illuminates red.
Illuminates when the ignition is
switched on and extinguishes shortly
after the engine starts.
Illuminates when the engine is
running
Caution
Engine lubrication may be
interrupted. This may result in
damage to the engine and/or
locking of the drive wheels.
1. Depress clutch.
2. Select neutral gear.
94
Instruments and controls
3. Move out of the flow of traffic as
quickly as possible without
impeding other vehicles.
4. Switch off ignition.
9 Warning
When the engine is off,
considerably more force is needed
to brake and steer.
During an Autostop, the brake
servo unit will still be operational.
Do not remove key until vehicle is
stationary, otherwise the steering
wheel lock could engage
unexpectedly.
Check oil level before seeking
assistance of a workshop 3 187.
Low fuel
o illuminates yellow.
Level in fuel tank is too low.
Refuelling 3 178.
Bleeding the diesel fuel system
3 190.
Autostop
Low beam
D illuminates or flashes green.
9 illuminates green.
Illuminated when low beam is on.
Illuminates green
Engine is in an Autostop.
Fog light
Flashes green
> illuminates green.
The front fog lights are on 3 114.
Autostop is temporarily unavailable,
or Autostop mode is invoked
automatically.
Stop-start system 3 137.
Exterior light
8 illuminates green.
The exterior lights are on 3 110.
High beam
C illuminates blue.
Illuminated when high beam is on or
during headlight flash 3 111.
High beam assist
f illuminates green.
The high beam assist is activated,
see Adaptive forward lighting 3 112.
Rear fog light
ø illuminates yellow.
The rear fog light is on 3 115.
Rain sensor
< illuminates green.
Illuminated when rain sensor position
on wiper stalk is selected.
Side blind spot alert
B illuminates green.
The system is active.
Cruise control
m illuminates in the Driver
Information Centre.
Instruments and controls
Cruise control 3 151.
Information displays
Speed limiter
Driver Information Centre
ß illuminates in the Driver
Information Centre.
Speed limiter 3 153.
The Driver Information Centre is
located in the instrument cluster.
Depending on the version and the
instrument cluster, the Driver
Information Centre is available as
Baselevel or Midlevel display.
Driver Information Centre indicates:
● overall and trip odometer
● digital speed indication
● trip/fuel information menu
● gear shift indication
● service information
● vehicle and warning messages
● driver assistance messages
● pop-up messages
Traffic sign assistant
L displays by the front camera
detected traffic signs in the Driver
Information Centre.
Traffic sign assistant 3 151.
Door open
h illuminates red.
A door or the tailgate is open.
95
Selecting menus and functions
The menus and functions can be
selected via the buttons on the turn
signal lever.
Turn the adjuster wheel to select a
page in the Trip/fuel information
menu.
Press SET/CLR to confirm or reset a
function.
Vehicle and service messages are
popped up in the Driver Information
Centre if required. Scroll messages
by turning the adjuster wheel.
Confirm messages by pressing
SET/CLR. Vehicle messages 3 101.
96
Instruments and controls
Trip/fuel information menu,
Baselevel display
Turn the adjuster wheel to select a
page:
Trip odometer
The recorded distance since the
reset.
Press L for 2 seconds to reset trip
odometer.
Average fuel consumption
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
To reset, press SET/CLR for a few
seconds.
Average speed
Display of average speed. The
measurement can be reset at any
time.
To reset, press SET/CLR for a few
seconds.
Fuel range
Range is calculated from current fuel
level and current consumption. The
display shows average values.
After refuelling, the range is updated
automatically after a brief delay.
When the level in the fuel tank is low,
a message appears on the display
and the control indicator o in the fuel
gauge illuminates 3 94.
Instantaneous Fuel Consumption
Display of the instantaneous
consumption.
Digital speed
Digital display of the instantaneous
speed.
Trip/fuel information menu,
Midlevel display
Differerent pages with combined
information can be selected.
Turn the adjuster wheel to select a
page.
Information page:
Fuel range
Range is calculated from current fuel
level and current consumption. The
display shows average values.
After refuelling, the range is updated
automatically after a brief delay.
Instruments and controls
When the level in the fuel tank is low,
a message appears on the display
and the control indicator o in the fuel
gauge illuminates 3 94.
Instantaneous Fuel Consumption
Display of the instantaneous
consumption.
Trip 1 page:
Average speed
Display of average speed. The
measurement can be reset at any
time.
Average fuel consumption
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
Distance travelled
Displays the current distance for trip
1 since the reset.
The values of trip 1 page can be reset
by pressing SET/CLR for a few
seconds.
Trip 2 page:
Average speed
Display of average speed. The
measurement can be reset at any
time.
Average fuel consumption
Display of average consumption. The
measurement can be reset at any
time and starts with a default value.
Distance travelled
Displays the current distance for trip
2 since a certain reset.
The values of trip 2 page can be reset
by pressing SET/CLR for a few
seconds.
Digital speed page
Digital display of the instantaneous
speed.
Stop and Start time counter
A time counter calculates the time
spent in STOP mode during a
journey. It resets to zero every time
the ignition is switched on.
Compass page
Displays the geographic direction of
driving.
97
Blank page
No trip/fuel information is displayed.
Info display
The Info-Display is located in the
instrument panel near the instrument
cluster.
Depending on the vehicle
configuration the vehicle has a
● Graphic-Info-Display
or
● 7'' Colour-Info-Display with
touchscreen functionality
or
● 8'' Colour-Info-Display with
touchscreen functionality
The Info displays can indicate:
● time 3 78
● outside temperature 3 77
● date 3 78
● Infotainment system, see
description in the Infotainment
manual
● indication of rear view camera
3 172
98
●
●
●
●
●
Instruments and controls
indication of panoramic view
system 3 169
indication of parking assist
instructions 3 160
navigation, see description in the
Infotainment manual
vehicle and system messages
3 101
settings for vehicle
personalisation 3 102
Press èäåé to select a menu page.
Press OK to confirm a selection.
Press BACK to exit a menu without
changing a setting.
7'' Colour-Info-Display
Selecting menus and settings
Menus and settings are accessed via
the display.
Graphic-Info-Display
Press X to switch on the display.
Press MENU to select main menu
page.
Press X to switch on the display.
Press ; to display the homepage.
Touch required menu display icon
with the finger.
Touch a respective icon to confirm a
selection.
Touch 9 to return to the next higher
menu level.
Press ; to return to the homepage.
For further information, see
Infotainment manual.
Vehicle personalisation 3 102.
8'' Colour-Info-Display
Selecting menus and settings
There are three options to operate the
display:
● via buttons below the display
● by touching the touchscreen with
the finger
● via speech recognition
Instruments and controls
Button and touch operation
Speech recognition
Description see Infotainment manual.
Vehicle personalisation 3 102.
Head-up display
Press X to switch on the display.
Press SET to select system settings
(units, language, time and date).
Press Í to select vehicle settings or
driving functions.
Touch required menu display icon or
a function with the finger.
Confirm a required function or
selection by touching.
Touch r on the display to exit a
menu without changing a setting.
For further information, see
Infotainment manual.
The Head-up display (HUD) displays
driver information concerning the
instrument cluster onto a foldable
projection plane on the driver's side.
The information appears as an image
projected from a lense in the
instrument panel onto the projection
plane directly ahead in driver's view.
The image appears focused out
toward the front of the vehicle.
99
Head-up display views:
● vehicle speed
● speed limits by the traffic sign
assistant
● set speed of speed limiter
● set speed of cruise control
● navigation information.
Adjust position of Head-up
display image
1. Adjust the driver's seat.
2. Start the engine.
3. Press ä or å to centre the image.
It can only be adjusted up and
down, not side to side.
100
Instruments and controls
9 Warning
If the head-up display image is too
bright or too high in your field of
view, it may obstruct your view
when it is dark outside. Be sure to
keep the head-up display image
dim and placed low in your field of
view.
Adjust brightness
The Head-up display image will
automatically dim and brighten to
compensate for outside lighting.
Brightness can also be adjusted
manually as needed:
Press e to brighten the display. Press
æ to dim the display.
The image can temporarily light up
depending on angel and position of
sunlight.
Switching off
Press æ and hold to turn the Head-up
display off.
Language
Preferred language can be set in
vehicle personalisation menu 3 102.
Units
Units can be changed in vehicle
personalisation menu 3 102.
Care of Head-up display
Clean the screen of the Head-up
display with a soft cloth sprayed with
glass cleaner. Wipe the lens gently,
then dry it.
System limitations
Head-up display may not operate
properly when:
● The lens in the instrument panel
is covered by objects or not
clean.
● Display brightness is too dim or
bright.
● Image is not adjusted to the
proper height.
● The driver wears polarized
sunglasses.
If the head-up image is not correct for
other reasons, contact a workshop.
Instruments and controls
Vehicle messages
Messages in the
Colour-Info-Display
Messages are indicated in the Driver
Information Centre, in some cases
together with a warning and signal
chime.
Some important messages may
appear additionally in the
Info-Display. Some messages only
pop-up for a few seconds.
Warning chimes
When starting the engine or whilst
driving
Press SET/CLR on the turn signal
lever to confirm a message.
Vehicle and service messages
The vehicle messages are displayed
as text. Follow the instructions given
in the messages.
Only one warning chime will sound at
a time.
The warning chime regarding not
fastened seat belts has priority over
any other warning chime.
● If a seat belt is not fastened.
● If a door or the tailgate is not fully
closed when starting off.
● If a certain speed is exceeded
with parking brake applied.
● If cruise control deactivates
automatically.
● If a programmed speed or speed
limit is exceeded.
●
●
●
●
●
101
If a warning message appears in
the Driver Information Centre.
If the electronic key is not in the
passenger compartment.
If the parking assist detects an
object.
If an unintended lane change
occurs.
If the diesel particle filter has
reached the maximum filling
level.
When the vehicle is parked and/or
the driver's door is opened
●
With exterior lights on.
During an Autostop
●
●
If the driver's door is opened.
If any condition for an autostart is
not fulfilled.
Battery voltage
When the vehicle battery voltage is
running low, a warning message will
appear in the Driver Information
Centre.
102
Instruments and controls
When the vehicle is being driven, the
load reduction function temporarily
deactivates certain functions, such as
the air conditioning, the heated rear
screen, heated steering wheel, etc.
The deactivated functions are
reactivated automatically as soon as
conditions permit.
Vehicle personalisation
Select ˆ Personalisationconfiguration, I OK.
The vehicle's behaviour can be
personalised by changing the settings
in the Info-Display.
Depending on vehicle equipment and
country-specific regulations some of
the functions described below may
not be available.
Some functions are only displayed or
active when the engine is running.
Unit settings
Select Display configuration, I OK.
Select Choise of units, I OK.
Select desired settings, I OK.
Graphic-Info-Display
Press MENU to open the menu page.
Use four-way button to operate the
display:
Language settings
Select Display configuration, I OK.
Select Choise of language, I OK.
Select desired language, I OK.
Vehicle settings
Select Define vehicle parameters, I
OK.
In the corresponding submenus the
following settings can be changed:
● Lighting.
Follow me home headlamps:
Activation and setting duration
time.
Welcome lighting: Activation and
setting duration time.
● Comfort
Ambient lighting: Activation/
Deactivation.
Instruments and controls
●
●
Rear wiper in reverse gear:
Activation/Deactivation.
Vehicle
Unlocking boot only: Activation/
Deactivation.
Plip action: Driver/all doors.
Driving assistance
Fatigue Detection system:
Activation/Deactivation.
Speed recommendation:
Activation/Deactivation.
7" Colour-Info-Display
Press ; to open homepage.
Use touch buttons to operate the
display:
Select Settings.
Unit settings
Select Units
Change units for Consumption and
Distance and Temperature.
Touch 9 repeatedly to return to the
homepage.
Language settings
Select Language.
Change language by touching the
respective entry.
Touch 9 repeatedly to return to the
homepage.
Vehicle settings
Select Vehicle.
In the corresponding submenus the
following settings can be changed:
● Collision / Detection Systems
Side Blind Spot Alert: Activates
or deactivates side blind spot
alert.
●
●
103
Drowsy Driver Alert: Activates or
deactivates the driver
drowsiness system.
Speed Limit Information:
Activates or deactivates the
speed limit information by traffic
sign recognition.
Rear View Camera Guidelines:
Activates or deactivates the rear
view camera guidelines on the
Info display.
Comfort and Convenience
Auto Wipe in Reverse Gear:
Activates or deactivates
automatic switching on of the
rear window wiper when reverse
gear is engaged.
Lighting
Ambient Lighting: Activates or
deactivates the ambient lighting
and adjusts its brightness.
Welcome Lighting: Activates or
deactivates and changes the
duration of welcome lighting.
104
Instruments and controls
Exit Lighting: Activates or
deactivates and changes the
duration of exit lighting.
● Remote Lock, Unlock, Start
Remote Door Unlock: Changes
the configuration to unlock the
driver's door only or all doors
when pressing O on the remote
control.
Unlock boot only: Activates or
deactivates unlocking the tailgate
only when pressing T on the
remote control.
Touch 9 repeatedly to return to the
homepage.
8" Colour-Info-Display
Change language by touching the
respective entry.
Confirm with G
Touch r repeatedly to exit the menu.
Vehicle settings
Press SET to open settings menu.
Use touch buttons to operate the
display.
Unit settings
Select System settings.
Change units for Consumption and
Distance and Temperature.
Confirm with G
Touch r repeatedly to exit the menu.
Language settings
Select Languages.
Press Í.
Select Vehicle settings.
In the corresponding submenus the
following settings can be changed:
● Headlights
Welcome lighting: Activates or
deactivates the function and
adjusts its duration.
Instruments and controls
●
●
●
Guide-me-home lighting:
Activates or deactivates the
function and adjusts its duration.
Comfort
Mood lighting: Adjusts the
brightness of the ambient
lighting.
Rear wiper in reverse: Activates
or deactivates automatic
switching on of the rear window
wiper when reverse gear is
engaged.
Vehicle access
Door unlock: boot only: Activates
or deactivates unlocking the
tailgate only when pressing T
on the remote control.
Door unlock: driver only:
Changes the configuration to
unlock the driver's door only or all
doors when pressing O on the
remote control.
Safety
Driver attention warning:
Activates or deactivates the
driver drowsiness system.
Driving functions
105
Telematics service
OnStar
OnStar is a personal connectivity and
service assistant with integrated
Wi-Fi hotspot. The OnStar service is
available 24 hours a day, seven days
a week.
Notice
OnStar is not available for all
markets. For further information,
contact your workshop.
Press Í.
Select Driving functions.
In the corresponding submenus the
following settings can be changed:
● Park Assist: Activates advanced
park assist, a parking maneuver
can be selected.
● Blind Spot Sensors: Activates or
deactivates side blind spot alert.
● Panoramic view system:
Activation/deactivation of the
function.
Notice
In order to be available and
operational, OnStar needs a valid
OnStar subscription, functioning
vehicle electrics, ignition on, mobile
service and GPS satellite link.
To activate the OnStar services and
set up an account, press Z and speak
with an advisor.
106
Instruments and controls
Depending on the equipment of the
vehicle, the following services are
available:
● Emergency services and support
in the case of a vehicle
breakdown
● Wi-Fi hotspot
● Smartphone application
● Remote control, e.g. location of
the vehicle, activation of horn and
lights, control of central locking
system
● Stolen vehicle assistance
● Vehicle diagnostics
Notice
The OnStar module of the vehicle is
deactivated after ten days without an
ignition cycle. Functions requiring a
data connection will be available
again after switching on the ignition.
OnStar buttons
Privacy button
Press and hold j until a message is
heard to activate or deactivate the
transmission of the vehicle location.
Press j to answer a call or to end a
call to an advisor.
Press j to access the Wi-Fi settings.
Service button
Press Z to establish a connection to
an advisor.
SOS button
Press [ to establish a priority
emergency connection to a specially
trained emergency advisor.
Status LED
Green: The system is ready with
activated transmission of the vehicle
location.
Green flashing: The system is on a
call.
Red: A problem arose.
Off: The system is ready with
deactivated transmission of the
vehicle location or the system is in
standby mode.
Red / green flashing for a short period
of time: The transmission of the
vehicle location has been
deactivated.
OnStar services
General services
If you need any information e.g.
opening hours, points of interest and
destinations or if you need any
support e.g. in the case of a vehicle
Instruments and controls
breakdown, a flat tyre and empty fuel
tank, press Z to establish a
connection to an advisor.
Notice
The Wi-Fi hotspot functionality is not
available for all markets.
Emergency services
In the case of an emergency situation,
press [ and talk to an advisor. The
advisor then contacts emergency or
assistance service providers and
directs them to your vehicle.
In the case of an accident with
activation of airbags or belt
tensioners, an automatic emergency
call is established. The advisor is
immediately connected to your
vehicle to see whether help is
needed.
Up to seven devices may be
connected.
To connect a mobile device with the
Wi-Fi hotspot:
1. Press j and then select Wi-Fi
settings on the Info-Display. The
settings displayed include the WiFi hotspot name (SSID),
password and connection type.
2. Start a Wi-Fi network search on
your mobile device.
3. Select your vehicle hotspot
(SSID) when listed.
4. When prompted, enter the
password on your mobile device.
Notice
Establishing an emergency call may
not be possible in areas without
sufficient network availability or due
to hardware damage during an
accident.
Wi-Fi hotspot
The Wi-Fi hotspot of the vehicle
provides internet connectivity with a
maximum speed of 4G/LTE.
Notice
To change the SSID or password,
press Z and talk to an advisor or log
in to your account.
To switch off the Wi-Fi hotspot
functionality, press Z to call an
advisor.
107
Smartphone app
With the My Vauxhall smartphone
app, some vehicle functions can be
operated remotely.
The following functions are available:
● Lock or unlock vehicle.
● Honk horn or flash lights.
● Check fuel level.
● Locate vehicle on a map.
● Manage Wi-Fi settings.
To operate these functions, download
the app from App Store® or
Google Play™ Store.
Remote control
If desired, use any phone to call an
advisor, who can remotely operate
specific vehicle functions. Find the
respective OnStar phone number on
our country-specific website.
The following functions are available:
● Lock or unlock vehicle.
● Provide information on the
vehicle location.
● Honk horn or flash lights.
108
Instruments and controls
Stolen vehicle assistance
If the vehicle is stolen, report the theft
to the authorities and request OnStar
stolen vehicle assistance. Use any
phone to call an advisor. Find the
respective OnStar phone number on
our country-specific website.
OnStar can provide support in
locating and recovering the vehicle.
Theft alert
When the anti-theft alarm system is
triggered, a notification is sent to
OnStar. You are then informed about
this event by text message or email.
Restart prevention
By sending remote signals, OnStar
can prevent the vehicle from
restarting once it has been turned off.
On-demand diagnostics
At any time e.g. if the vehicle displays
a vehicle message, press Z to
contact an advisor and ask to
complete a real-time diagnostic check
to directly determine the issue.
Depending on the results, the advisor
will provide further support.
Diagnostic report
The vehicle automatically transmits
diagnostic data to OnStar which
sends a monthly email report to you
and your preferred workshop.
Notice
The workshop notification function
can be disabled in your account.
The report contains the status of key
operating systems of the vehicle like
engine, transmission, airbags, ABS,
and other major systems. It also
provides information on possible
maintenance items and tyre pressure
(only with tyre pressure monitoring
system).
To look at the information in greater
detail, select the link within the email
and log in to your account.
OnStar settings
OnStar PIN
To have full access to all OnStar
services, a four-digit PIN is required.
The PIN has to be personalised when
first talking to an advisor.
To change the PIN, press Z to call an
advisor.
Account data
An OnStar subscriber has an account
where all the data is stored. To
request a change of the account
information, press Z and talk to an
advisor or log in to your account.
If the OnStar service is used on
another vehicle, press Z and request
that the account be transferred to the
new vehicle.
Notice
In any case, if the vehicle is disposed
of, sold or otherwise transferred,
immediately inform OnStar about
the changes and terminate the
OnStar service on this vehicle.
Vehicle location
The vehicle location is transmitted to
OnStar when service is requested or
triggered. A message on the InfoDisplay informs about this
transmission.
To activate or deactivate the
transmission of the vehicle location,
press and hold j until an audio
message is heard.
Instruments and controls
The deactivation is indicated by the
status light flashing red and green for
a short period of time and each time
the vehicle is started.
Notice
If the transmission of the vehicle
location is deactivated, some
services are no longer available.
Notice
The vehicle location always remains
accessible to OnStar in the case of
an emergency.
Find the privacy policy in your
account.
Software updates
OnStar may remotely carry out
software updates without further
notice or consent. These updates are
to enhance or maintain safety and
security or the operation of the
vehicle.
These updates may concern privacy
issues. Find the privacy policy in your
account.
109
110
Lighting
Lighting
Exterior lighting .......................... 110
Light switch .............................. 110
Automatic light control ............. 111
High beam ............................... 111
Headlight flash ......................... 111
Headlight range adjustment .... 112
Daytime running lights ............. 112
Adaptive forward lighting ......... 112
Hazard warning flashers .......... 113
Turn and lane-change signals . 114
Front fog lights ......................... 114
Rear fog light ........................... 115
Parking lights ........................... 115
Reversing lights ....................... 115
Misted light covers ................... 115
Interior lighting ........................... 116
Instrument panel illumination
control ..................................... 116
Interior lights ............................ 116
Reading lights .......................... 116
Sunvisor lights ......................... 117
Lighting features ........................ 117
Centre console lighting ............ 117
Entry lighting ............................ 117
Exit lighting .............................. 117
Battery discharge protection .... 118
Exterior lighting
Light switch
Turn light switch:
AUTO : automatic light control
switches automatically
between daytime running
light and headlight
: sidelights
8
: headlights
9
Control indicator 8 3 94.
Tail lights
Tail lights are illuminated together
with low/high beam and sidelights.
Lighting
Automatic light control
Additionally, headlights are switched
on if the windscreen wipers have
been activated for several wipes.
Adaptive forward lighting 3 112
111
Headlight flash
Tunnel detection
When a tunnel is entered headlights
are switched on immediately.
High beam
When the automatic light control
function is switched on and the
engine is running, the system
switches between daytime running
lights and headlights automatically
depending on the external lighting
conditions and information given by
the rain sensor system.
Daytime running light 3 112.
Automatic headlight activation
During poor lighting conditions
headlights are switched on.
To activate the headlight flash, pull
lever.
Pulling lever deactivates high beam.
Push lever to switch from low to high
beam.
Pull lever to deactivate high beam.
High beam assist 3 112.
112
Lighting
Headlight range adjustment
Daytime running lights
Manual headlight range
adjustment
Daytime running lights increases
visibility of the vehicle during daylight.
They are switched on automatically
during daytime when engine is
running.
The system switches between
daytime running lights and low beam
automatically, depending on the
lighting conditions.
Adaptive forward lighting
To adapt headlight range to the
vehicle load to prevent dazzling: turn
thumb wheel ? to required position.
0 : front seats occupied
1 : all seats occupied
2 : all seats occupied and load
compartment laden
3 : driver's seat occupied and load
compartment laden
The Adaptive forward lighting
functions are only available with LED
headlights.
LED headlights for low and high beam
ensure better visibility under all
conditions.
Operation is the same as for halogen
headlights.
Adaptive forward lighting functions
are active automatically with light
switch in position AUTO. Adaptive
forward lighting includes following
functions:
●
●
●
cornering lights
high beam assist
automatic headlight levelling
Cornering light
When turning, depending on the
steering angle and the turn signal
light, particular LEDs are triggered
which illuminate the direction of
travel. It is activated up to a speed of
25 mph.
High beam assist
This feature allows high beam to
function as the main driving light at
night and when vehicle speed
exceeds 15 mph.
Lighting
It switches automatically to low beam
when:
● The camera or a sensor in the
windscreen detects the lights of
oncoming or preceding vehicles.
● The vehicle speed drops below
9 mph.
● It is foggy or snowy.
● Driving in urban areas.
If there are no restrictions detected,
the system switches back to high
beam.
Activation
Activate this function pressing a
button on the turn and lane change
lever. The LED of the button
illuminates if the high beam assist is
activated. The high beam is switched
on automatically at a speed above
15 mph.
The green control indicator f
illuminates continuously when the
assist is activated, the blue one 7
illuminates when high beam is on.
Control indicator f 3 94.
Deactivation
Deactivate this function pressing a
button on the turn and lane change
lever.
If a headlight flash is activated when
the high beam assist is activated and
low beam is on, the high beam assist
will be deactivated. The system
changes to high beam.
If a headlight flash is activated when
the high beam assist is activated and
high beam is on, the high beam assist
will be deactivated. The system
changes to low beam.
To reactivate the high beam assist,
flash the headlights again.
113
Automatic headlight levelling
To prevent oncoming traffic from
being dazzled, headlight levelling is
automatically adjusted based on the
load in the vehicle.
Fault in Adaptive forward lightingLED system
When the system detects a failure in
the Adaptive forward lighting-LED
headlight system, a warning is
displayed in the Driver Information
Centre.
Hazard warning flashers
Operated by pressing ¨.
114
Lighting
When braking in an emergency, the
hazard warning flashers are switched
on automatically depending on the
force of deceleration. They are
switched off automatically the first
time you accelerate if you press ¨.
Turn and lane-change
signals
lever up
: right turn signal
lever down : left turn signal
A resistance point can be felt by
moving the lever.
Move the lever past the resistance
point to switch on constantly. When
the steering wheel moves opposite,
the turn signal is automatically
deactivated. Switch off manually by
moving the lever to its original
position.
Tap shortly to switch on for three
flashes, e.g., when changing lanes.
Move the lever to the resistance point
and hold for flashing until lever is
released.
If you forget to cancel the turn and
lane-change signals for more than
twenty seconds, the volume of the
audible signal will increase if the
speed is above 40 mph.
Front fog lights
Operated by pressing >.
Light switch in position AUTO:
switching on front fog lights will switch
headlights on automatically.
Lighting
Rear fog light
Parking lights
115
Reversing lights
The reversing light comes on when
the ignition is on and reverse gear is
selected.
Misted light covers
The inside of the light housing may
mist up briefly in poor, wet and cold
weather conditions, in heavy rain or
after washing. The mist disappears
quickly by itself; to help switch on the
headlights.
Operated by pressing ø.
Light switch in position AUTO:
switching on rear fog light will switch
headlights on automatically.
Light switch in position 8: rear fog
light can only be switched on with
front fog lights.
The vehicle rear fog light is
deactivated when towing a trailer or a
plug is connected with the socket, e.
g. when a bicycle carrier is used.
When the vehicle is parked, the
parking lights on one side can be
activated:
1. Switch off ignition.
2. Move turn signal lever all the way
up (right parking lights) or down
(left parking lights).
Confirmed by a signal and the
corresponding turn signal control
indicator.
116
Lighting
Interior lighting
Instrument panel
illumination control
Interior lights
Rear courtesy lights
During entry and exit of the vehicle,
the front and rear courtesy lights
automatically switch on and then off
after a delay.
Illuminate in conjunction with the front
courtesy light depending on rocker
switch position.
Notice
In the event of an accident with
airbag deployment the courtesy
lights are turned on automatically.
Reading lights
Front courtesy light
Brightness of the following lights can
be adjusted in position AUTO when
the light sensor detects night
conditions, or in position 8 or 9:
● instrument panel illumination
● Info-Display
● illuminated switches and
operation elements
Turn thumb wheel A and hold until
the desired brightness is obtained.
Operated by pressing s and t in the
courtesy lights.
Operate rocker switch:
w
: automatic switching on
and off
press u : on
press v : off
Lighting
Lighting features
Centre console lighting
A spotlight integrated in the overhead
console illuminates the centre
console when headlights are
switched off.
Entry lighting
Welcome lighting
Illustration shows rear courtesy lights.
Sunvisor lights
Illuminates when the cover is opened.
Some or all of the following lights are
switched on for a short time by
unlocking the vehicle with the radio
remote control:
● headlights
● tail lights
● number plate lights
● instrument panel light
● interior lights
The number of activated lights
depends on the surrounding light
conditions.
The lighting switches off immediately
when the ignition is switched on.
Starting off 3 17.
117
This function can be activated or
deactivated in the vehicle
personalisation.
Vehicle personalisation 3 102.
The following lights will additionally
switch on when the driver's door is
opened:
● illumination of some switches
● Driver Information Centre
● door pocket lights
Exit lighting
The following lights are switched on if
the key is removed from the ignition
switch:
● interior lights
● instrument panel light
They will switch off automatically after
a delay. This function works only in
the dark. Theatre lighting is activated
if the driver's door is opened during
this time.
118
Lighting
Battery discharge protection
Vehicle battery state of charge
function
The function guarantees longest
vehicle battery life via a generator
with controllable power output and
optimised power distribution.
To prevent discharge of the vehicle
battery when driving, the following
systems are reduced automatically in
two stages and finally switched off:
● auxiliary heater
● heated rear window and mirrors
● heated seats
● fan
In the second stage, a message
which confirms the activation of the
vehicle battery discharge protection
will be displayed in the Driver
Information Centre.
Switching off electric lights
To prevent discharge of the vehicle
battery when the ignition is switched
off, some interior lights are switched
off automatically after some time.
Climate control
Climate control
Climate control systems ............. 119
Heating and ventilation system 119
Air conditioning system ........... 120
Electronic climate control
system .................................... 123
Auxiliary heater ........................ 127
Air vents ..................................... 128
Adjustable air vents ................. 128
Fixed air vents ......................... 129
Maintenance .............................. 129
Air intake ................................. 129
Air conditioning regular
operation ................................ 130
Service .................................... 130
Climate control systems
Heating and ventilation
system
119
Temperature £
Adjust the temperature by turning
£ to the desired temperature.
red area : warmer
blue area : colder
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Air distribution l M K
Controls for:
● temperature £
● air distribution l, M and K
● fan speed Z
● demisting and defrosting à
● heated rear window and exterior
mirrors b
● heated seats ß
Press:
l : to windscreen and front door
windows
M : to head area and rear seats via
adjustable front air vents
K : to front and rear foot well and
windscreen
Combinations are possible.
Fan speed Z
Adjust the air flow by turning Z to the
desired speed.
to the right
: increase
to the left
: decrease
120
Climate control
Demisting and defrosting the
windows á
Heated seats ß
3 46.
Air conditioning system
●
●
●
●
●
Press á: the air distribution is
directed towards the windscreen.
Set temperature controller £ to
warmest level.
Set fan speed Z to highest level.
Switch on heated rear window b.
Open side air vents as required
and direct them towards the door
windows.
Heated rear window and exterior
mirrors b
3 38
Illustration shows functions which
may not be available for your
particular vehicle.
Controls for:
● temperature £
● air distribution l, M and K
● fan speed Z
● demisting and defrosting à
● air conditioning A/C
● air recirculation 4
●
●
●
heated rear window and exterior
mirrors b
heated windscreen ,
heated seats ß
Some changes of settings are
indicated briefly in the Info-Display.
Activated functions are indicated by
the LED in the respective button.
Temperature £
Adjust the temperature by turning
£ to the desired temperature.
red area : warmer
blue area : colder
Climate control
Heating will not be fully effective until
the engine has reached normal
operating temperature.
Air conditioning A/C
121
Activated cooling may inhibit
Autostops. Stop-start system 3 137.
Demisting and defrosting the
windows à
Air distribution l M K
Press:
l : to windscreen and front door
windows
M : to head area and rear seats via
adjustable front air vents
K : to front and rear foot well and
windscreen
Combinations are possible.
Fan speed Z
Adjust the air flow by turning Z to the
desired speed.
to the right
: increase
to the left
: decrease
Press A/C to switch on cooling.
Activation is indicated by the LED in
the button. Cooling is only functional
when the engine is running and
climate control fan is switched on.
Press A/C again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) as soon as the
outside temperature is slightly above
the freezing point. Therefore
condensation may form and drip from
under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons.
●
●
●
●
●
Press à: the air distribution is
directed towards the windscreen.
Set temperature controller £ to
warmest level.
Switch on air conditioning A/C if
required.
Set fan speed Z to highest level.
Switch on heated rear window b.
122
●
●
Climate control
Switch on heated
windscreen ,.
Open side air vents as required
and direct them towards the door
windows.
Notice
If à is pressed while the engine is
running, an Autostop will be inhibited
until à is pressed again.
If à is pressed while the engine is in
an Autostop, the engine will restart
automatically.
Stop-start system 3 137.
Air recirculation system 4
Press 4 to activate air recirculation
mode, LED is indicated.
Select air recirculation to assist in
cooling the interior or in blocking
outside odours or exhaust.
Press 4 again to deactivate air
recirculation mode.
Maximum cooling
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling, the
air humidity increases, so the
windows may mist up from inside.
The quality of the passenger
compartment air deteriorates,
which may cause the occupants to
feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate l.
Briefly open the windows so that hot
air can disperse quickly.
● Switch on air conditioning A/C.
● Press 4 for air recirculation
system on.
● Press M for air distribution.
● Set temperature control £ to
coldest level.
● Set fan speed Z to highest level.
● Open all vents.
Climate control
Heated rear window, windscreen
and exterior mirrors b
3 38
Heated seats ß
3 46.
Electronic climate control
system
The dual zone climate control allows
different temperatures for driver side
and front passenger side.
In automatic mode, temperature, fan
speed and air distribution are
regulated automatically.
Illustration shows functions which
may not be available for your
particular vehicle.
Controls for:
● temperature on driver side £
● MENU enters the Climate setting
menu in the Info-Display
● fan speed Z
● automatic mode AUTO
● temperature on front passenger
side £
● cooling A/C
● manual air recirculation 4
● demisting and defrosting à
● heated rear window and exterior
mirrors b
● heated windscreen ,
● heated seats ß
Activated functions are indicated by
the LED in the respective control.
The electronic climate control system
is only fully operational when the
engine is running.
123
Climate settings menu (MENU
button)
Settings for
● air distribution l, M, K
● fan speed Z
● temperature for driver and
passenger side 19°/21°
● dual zone temperature
synchronisation MONO
● air conditioning ON/OFF
● automatic mode AUTO
can be triggered manually in the
Climate setting menu. Press MENU to
enter the menu and follow the touch
buttons.
124
Climate control
Climate setting menu can also be
displayed
● by selecting Climate on the 7''
Colour-Info-Display or
● by pressing Í and then selecting
Climate from the menu on the 8''
Colour-Info-Display.
●
Automatic mode AUTO
●
Set the preselected
temperatures for driver and front
passenger using the left and right
control dial. Recommended
temperature is 22 °C.
Temperature is indicated in
displays beside the control dials
and in the climate settings menu.
Air recirculation mode 4 should
be deactivated. When
deactivated the LED in the button
is not illuminated.
Manual settings
Climate control system settings can
be changed by activating the
following functions:
Basic settings for automatic control
with maximum comfort:
● Press AUTO to start the air
conditioning automatically.
● Open all air vents to allow
optimised air distribution in
automatic mode.
Fan speed Z
Adjust the air flow by turning rotary
knob Z to the desired speed. Turn left
to decrease or turn right to increase.
Fan speed can also be changed by
touch buttons in the climate settings
display. Press MENU to enter the
menu.
Turning rotary knob Z anticlockwise:
fan and cooling are switched off.
To return to automatic mode, press
AUTO.
Climate control
Air distribution l, M, K
Temperature preselection £
125
If the minimum temperature Lo is set,
the climate control system runs at
maximum cooling, if cooling A/C is
switched on.
If the maximum temperature Hi is set,
the climate control system runs at
maximum heating.
Notice
If A/C is switched on, reducing the
set cabin temperature can cause the
engine to restart from an Autostop or
inhibit an Autostop.
Press MENU to enter the menu.
Touch (in the Colour-Info-Display):
l : to windscreen and front door
windows
M : to head area and rear seats via
adjustable air vents
K : to front and rear foot well and
windscreen
To return to automatic air distribution,
press AUTO.
Set the preselected temperatures
separately for driver and front
passenger to the desired value using
the left and right control dials. The dial
on the passenger side changes the
temperature for the passenger side.
The dial on the driver's side changes
the temperature for the driver's side or
for both sides depending on
activation of synchronisation MONO
in the climate settings menu. Press
MENU to enter the menu.
Recommended temperature is 22 °C.
Temperature is indicated in displays
beside the control dials and in the
climate settings menu.
Stop-start system 3 137.
Dual zone temperature
synchronisation MONO or SYNC
Press MENU to enter the menu.
Touch MONO or SYNC to link
passenger side temperature setting
to the driver side.
When passenger side control dial will
be adjusted, synchronisation is
deactivated.
126
Climate control
Air conditioning A/C
Manual air recirculation 4
compartment air deteriorates,
which may cause the occupants to
feel drowsy.
In warm and very humid ambient air
conditions, the windscreen may mist
up from outside, when cold air is
directed towards it. If windscreen
mists up from outside, activate
windscreen wiper and deactivate l.
Press A/C to switch on cooling. The
LED in the button illuminates to
indicate activation. Cooling is only
functional when the engine is running
and climate control fan is switched on.
Press A/C again to switch off cooling.
The air conditioning system cools and
dehumidifies (dries) when outside
temperature is above a specific level.
Therefore condensation may form
and drip from under the vehicle.
If no cooling or drying is required,
switch off the cooling system for fuel
saving reasons.
Press 4 to activate the air
recirculation mode. The LED in the
button illuminates to indicate
activation.
Press 4 again to deactivate
recirculation mode.
9 Warning
The exchange of fresh air is
reduced in air recirculation mode.
In operation without cooling, the
air humidity increases, so the
windows may mist up from inside.
The quality of the passenger
Climate control
Demisting and defrosting the
windows à
Notice
If à is pressed while the engine is
running, an Autostop will be inhibited
until à is pressed again.
If à is pressed while the engine is in
an Autostop, the engine will restart
automatically.
Stop-start system 3 137.
●
●
●
●
●
●
Press à. The LED in the button
illuminates to indicate activation.
Temperature and air distribution
are set automatically and the fan
runs at high speed.
Switch on air conditioning by
pressing A/C, if required.
Switch on heated rear window b.
Switch on heated
windscreen ,.
To return to previous mode press
à again, to return to automatic
mode press AUTO.
Deactivation of Electronic climate
control system
Cooling, fan and automatic mode can
be switched off by turning control dial
Z anticlockwise.
Activation by switching on the fan or
pressing AUTO.
Heated rear window, windscreen
and exterior mirrors b
3 38
Heated seats ß
3 46.
127
Auxiliary heater
Air heater
Quickheat is an electric auxiliary air
heater which automatically warms up
the passenger compartment more
quickly.
128
Climate control
Air vents
Adjustable air vents
Outer air vents in the instrument
panel
Centre air vent on top of the
instrument panel
Direct the flow of air by tilting and
swivelling the slats.
To close the vent, swivel the slats
outwards.
Close air flow by turning the thumb
wheel to the front.
Centre air vents in the instrument
panel
Direct the flow of air by tilting and
swivelling the slats.
To close the vent, swivel the slats
inwards.
Climate control
Air vent in the glovebox
Fixed air vents
Additional air vents are located
beneath the windscreen and door
windows and in the foot wells.
The air vent can be opened or closed
by turning.
At least two air vents must be open
while cooling is on.
9 Warning
Do not attach any objects to the
slats of the air vents. Risk of
damage and injury in case of an
accident.
129
Maintenance
Air intake
The air intake in front of the
windscreen in the engine
compartment must be kept clear to
allow air intake. Remove any leaves,
dirt or snow.
Cabin air filter
Change filter regulary for maximum
effect.
More frequent passenger
compartment air filter replacement
may be needed, if you drive in areas
with heavy traffic, poor air quality,
130
Climate control
areas with high dust levels or which
are sensitive to environmental
allergens.
Passenger compartment air filter
replacement may also be needed if
there is reduced air flow, windows
fogging up, or odors.
Your dealer can help to determine
when it is the right time to replace the
filter.
Air conditioning regular
operation
In order to ensure continuously
efficient performance, cooling must
be operated for a few minutes once a
month, irrespective of the weather
and time of year. Operation with
cooling is not possible when the
outside temperature is too low.
Service
For optimal cooling performance, it is
recommended to annually check the
climate control system, starting
three years after initial vehicle
registration, including:
●
●
●
●
●
●
●
functionality and pressure test
heating functionality
leakage check
check of drive belts
cleaning of condenser and
evaporator drainage
performance check
cabin air filter check
Driving and operating
Driving and
operating
Driving hints ............................... 132
Control of the vehicle ............... 132
Steering ................................... 132
Starting and operating ............... 132
New vehicle running-in ............ 132
Ignition switch positions ........... 132
Power button ........................... 133
Power saving mode ................. 134
Starting the engine .................. 135
Overrun cut-off ........................ 136
Stop-start system .................... 137
Parking .................................... 139
Engine exhaust .......................... 140
Diesel particle filter .................. 140
Catalytic converter ................... 140
AdBlue ..................................... 141
Automatic transmission .............. 144
Transmission display ............... 144
Selector lever .......................... 144
Manual mode ........................... 145
Electronic driving programmes 145
Fault ........................................ 146
Interruption of power supply .... 146
Manual transmission .................. 147
Brakes ........................................ 148
Antilock brake system ............. 148
Parking brake .......................... 148
Brake assist ............................. 149
Hill start assist ......................... 149
Ride control systems ................. 149
Electronic Stability Control and
Traction Control system ......... 149
Driver assistance systems ......... 151
Cruise control .......................... 151
Speed limiter ........................... 153
Forward collision alert ............. 155
Active emergency braking ....... 156
Front pedestrian protection ..... 158
Parking assist .......................... 160
Advanced parking assist ......... 163
Side blind spot alert ................. 168
Panoramic view system ........... 169
Rear view camera ................... 172
Lane departure warning .......... 173
Driver alert ............................... 175
Fuel ............................................ 176
Fuel for petrol engines ............. 176
Fuel for diesel engines ............ 177
Fuel for liquid gas operation .... 177
Refuelling ................................ 178
131
Trailer hitch ................................ 180
General information ................. 180
Driving characteristics and
towing tips .............................. 180
Trailer towing ........................... 180
Towing equipment ................... 181
132
Driving and operating
Driving hints
Control of the vehicle
Never coast with engine not
running
Many systems will not function in this
situation (e.g. brake servo unit, power
steering). Driving in this manner is a
danger to yourself and others.
All systems function during an
Autostop.
Stop-start system 3 137.
Idle boost
If charging of the vehicle battery is
required due to battery condition, the
power output of the generator must
be increased. This will be achieved by
an idle boost which may be audible.
A message appears in the Driver
Information Centre.
Pedals
To ensure the pedal travel is
uninhibited, there must be no mats in
the area of the pedals.
Use only floor mats, which fit properly
and are fixed by the retainers on the
driver side.
Steering
If power steering assist is lost
because the engine stops or due to a
system malfunction, the vehicle can
be steered but may require increased
effort.
Starting and operating
New vehicle running-in
Do not brake unnecessarily hard for
the first few journeys.
During the first drive, smoke may
occur because of wax and oil
evaporating off the exhaust system.
Park the vehicle in the open for a
while after the first drive and avoid
inhaling the fumes.
During the running-in period, fuel and
engine oil consumption may be
higher.
Additionally, the cleaning process of
the diesel particle filter may take
place more often.
Diesel particle filter 3 140.
Autostop may be inhibited to allow
charging of the vehicle battery.
Ignition switch positions
Turn key:
Driving and operating
9 Danger
Never remove the key from
ignition switch during driving as
this will cause steering wheel lock.
Power button
0 : ignition off: Some functions
remain active until key is
removed or driver's door is
opened, provided the ignition was
on previously
1 : ignition on power mode: Ignition
is on, diesel engine is preheating.
Control indicators illuminate and
most electrical functions are
operable
2 : engine start: Release key after
after engine has been started
Steering wheel lock
Remove key from ignition switch and
turn steering wheel until it engages.
133
Ignition on power mode without
starting the engine
Press Start/Stop without operating
clutch or brake pedal. Control
indicators illuminate and most
electrical functions are operable.
Engine and ignition off
Press Start/Stop briefly in each mode
or when engine is running and vehicle
is stationary. Some functions remain
active until driver's door is opened,
provided the ignition was on
previously.
Emergency shut off during driving
Press Start/Stop for five seconds
3 135. Steering wheel locks as soon
as vehicle is stationary.
Steering wheel lock
Electronic key must be inside the
vehicle.
Engine start
Operate clutch pedal (manual
transmission) or brake pedal
(automatic transmission) and press
Start/Stop. Release button after
starting procedure begins. Diesel
engine starts after preheating.
The steering wheel lock activates
automatically when:
● The vehicle is stationary.
● The ignition has been switched
off.
To release steering wheel lock, open
and close driver's door and switch on
accessory mode or start the engine
directly.
134
Driving and operating
Power saving mode
9 Warning
This function manages the duration of
using certain systems to avoid
discharging of the vehicle battery.
After the engine has stopped, some
systems can still be used such as the
audio and telematics system,
windscreen wipers, dipped beam
headlamps, courtesy lamps, etc. for a
total maximum time of about forty
minutes.
If the vehicle battery is discharged,
the vehicle must not be towed,
tow-started or jump-started as the
steering wheel lock cannot be
disengaged.
Operation on vehicles with
electronic key system in case of
failure
If either the electronic key fails or the
battery of the electronic key is weak,
the Driver Information Centre may
display No Remote Detected or
Replace Battery in Remote Key when
you try to start the vehicle.
Hold the electronic key with buttons
outside at the marking on the steering
column cover as shown in the
illustration.
Depress the clutch pedal (manual
transmission) or the brake pedal
(automatic transmission or manual
transmission automated) and press
Start/Stop button to start the engine.
This option is intended for
emergencies only. Replace the
electronic key battery as soon as
possible 3 23.
For unlocking or locking the doors,
see fault in radio remote control unit
or electronic key system 3 24.
Changing into power saving
mode
When a certain discharging status of
the vehicle battery is achieved, the
active functions are switched in
standby mode. A message appears in
the Driver Information Centre
indicating Power saving mode.
A telephone call being made at this
time will be maintained for around 10
minutes with the Bluetooth handsfree
system of the Infotainment system.
Driving and operating
Deactivating power saving mode
Starting the engine
Standby mode is reactivated
automatically next time the vehicle is
driven. To use the functions
immediately, start the engine:
● for less than ten minutes to use
the systems for approximately
five minutes
● for more than ten minutes to use
the systems for up to
approximately thirty minutes.
Have the engine run for the duration
specified to ensure that the battery
charge is sufficient. Do not repeatedly
and continuously restart the engine in
order to charge the battery.
Vehicles with ignition switch
135
Turn key briefly to position 2 and
release after the engine has been
started.
Manual transmission: during an
Autostop, the engine can be started
by depressing the clutch pedal
3 137.
Automatic transmission: during an
Autostop, the engine can be started
by releasing the brake pedal 3 137.
Vehicles with power button
Turn key to position 1 to release the
steering wheel lock.
Manual transmission: operate clutch
and brake pedal.
Automatic transmission: operate
brake pedal and move selector lever
to P or N.
Do not operate accelerator pedal.
Diesel engines: wait until control
indicator ! extinguishes.
Manual transmission: operate clutch
and brake pedal.
136
Driving and operating
Automatic transmission: operate
brake pedal and move selector lever
to P or N.
Do not operate accelerator pedal.
Press and release Start/Stop: an
automatic procedure operates the
starter with a short delay until the
engine is running.
Before restarting or to switch off the
engine when vehicle is stationary,
press Start/Stop once more briefly.
Manual transmission: during an
Autostop, the engine can be started
by depressing the clutch pedal
3 137.
Automatic transmission: during an
Autostop, the engine can be started
by releasing the brake pedal 3 137.
Emergency shut off during driving
If the engine needs to be switched off
during driving in case of emergency,
press Start/Stop for five seconds.
9 Danger
Switching off the engine during
driving may cause loss of power
support for brake and steering
systems. Assistance systems and
airbag systems are disabled.
Lighting and brake lights will
extinguish. Therefore power down
the engine and ignition while
driving only when required in case
of emergency.
Starting the vehicle at low
temperatures
Starting the engine without additional
heaters is possible down to -25 °С for
diesel engines and -30 °C for petrol
engines. Required is an engine oil
with the correct viscosity, the correct
fuel, performed services and a
sufficiently charged vehicle battery.
With temperatures below -30 °C the
automatic transmission requires a
warming phase of approx.
five minutes. The selector lever must
be in position P.
Heating functionalities
Notice
Individual heating functionalities,
such as heated seats or heated
steering wheel, may be temporarily
unavailable in the event of electrical
loading constraints. Functions will
be resumed after some minutes.
Turbo engine warm-up
Upon start-up, engine available
torque may be limited for a short time,
especially when the engine
temperature is cold. The limitation is
to allow the lubrication system to fully
protect the engine.
Overrun cut-off
The fuel supply is automatically cut off
during overrun, i.e. when the vehicle
is driven with a gear engaged but
accelerator pedal is released.
Depending on driving conditions, the
overrun cut-off may be deactivated.
Driving and operating
Stop-start system
The stop-start system helps to save
fuel and to reduce the exhaust
emissions. When conditions allow, it
switches off the engine as soon as the
vehicle is at a low speed or at a
standstill, e.g. at a traffic light or in a
traffic jam.
Activation
The stop-start system is available as
soon as the engine is started, the
vehicle starts-off and the conditions
as stated below in this section are
fulfilled.
Deactivation
Deactivate the stop-start system
manually by pressing Ò. The
deactivation is indicated when the
LED in the button illuminates.
137
Indication
Autostop
Vehicles with manual transmission
An Autostop can be activated at a
standstill.
Activate an Autostop as follows:
● Depress the clutch pedal.
● Set the lever to neutral.
● Release the clutch pedal.
The engine will be switched off while
the ignition stays on.
Vehicles with automatic transmission
If the vehicle is at a standstill with
depressed brake pedal, Autostop is
activated automatically.
The engine will be switched off while
the ignition stays on.
The stop-start system will be disabled
on inclines.
An Autostop is indicated by control
indicator D.
During an Autostop, the heating and
brake performance will be
maintained.
Conditions for an Autostop
The stop-start system checks if each
of the following conditions is fulfilled.
● The stop-start system is not
manually deactivated.
● The driver's door is closed or the
driver's seat belt is fastened.
● The vehicle battery is sufficiently
charged and in good condition.
● The engine is warmed up.
● The engine coolant temperature
is not too high.
138
Driving and operating
●
The engine exhaust temperature
is not too high, e.g. after driving
with high engine load.
● The ambient temperature is
sufficient.
● The climate control system
allows an Autostop.
● The brake vacuum is sufficient.
● The self-cleaning function of the
diesel particle filter is not active.
Otherwise an Autostop will be
inhibited.
Certain settings of the climate control
system may inhibit an Autostop. See
Climate control chapter for more
details 3 120.
If an autostop is temporarily not
available, D flashes green 3 94.
Immediately after driving at a higher
speed an Autostop may be inhibited.
New vehicle running-in 3 132.
Vehicle battery discharge protection
To ensure reliable engine restarts,
several vehicle battery discharge
protection features are implemented
as part of the stop-start system.
Power saving measures
During an Autostop, several electrical
features such as auxiliary electric
heater or rear window heating are
disabled or switched to a power
saving mode. The fan speed of the
climate control system is reduced to
save power.
Restart of the engine by the driver
Vehicles with manual transmission
Conventional restart
All engines have conventional restart.
Depress the clutch pedal without
depressing the brake pedal to restart
the engine.
On engines with late restart a
conventional restart is only possible
without depressed brake pedal.
Restart of the engine by the stopstart system
The selector lever must be in neutral
to enable an automatic restart.
If one of the following conditions
occurs during an Autostop, the
engine will be restarted automatically
by the stop-start system:
●
The stop-start system is
manually deactivated.
● The driver's seat belt is
unfastened or the driver's door is
opened.
● The engine temperature is too
low.
● The charging level of the vehicle
battery is below a defined level.
● The brake vacuum is not
sufficient.
● The climate control system
requests an engine start.
● The air conditioning is manually
switched on.
If an electrical accessory, e.g. a
portable CD player, is connected to
the power outlet, a brief power drop
during the restart might be noticeable.
Driving and operating
Parking
9 Warning
●
●
●
●
Do not park the vehicle on an
easily ignitable surface. The
high temperature of the
exhaust system could ignite the
surface.
Always apply the parking
brake. Activate the manual
parking brake without pressing
the release button. Apply as
firmly as possible on a downhill
slope or uphill slope. Depress
brake pedal at the same time to
reduce operating force.
Switch off the engine.
If the vehicle is on a level
surface or uphill slope, engage
first gear or set the selector
lever to position P before
removing the ignition key or
switching off ignition on
vehicles with power button. On
an uphill slope, turn the front
wheels away from the kerb.
●
●
●
●
●
If the vehicle is on a downhill
slope, engage reverse gear or
set the selector lever to position
P before removing the ignition
key or switching off ignition on
vehicles with power button.
Turn the front wheels towards
the kerb.
Close the windows.
Remove the ignition key from
the ignition switch or switch off
ignition on vehicles with power
button. Turn the steering wheel
until the steering wheel lock is
felt to engage.
Lock the vehicle.
Activate the anti-theft alarm
system.
The engine cooling fans may run
after the engine has been
switched off 3 186.
Caution
After running at high engine
speeds or with high engine loads,
operate the engine briefly at a low
139
load or run in neutral for
approx. 30 seconds before
switching off, in order to protect
the turbocharger.
Notice
In the event of an accident with
airbag deployment, the engine is
switched off automatically if the
vehicle comes to a standstill within a
certain time.
Emergency operation under
extreme cold temperatures
9 Warning
This emergency operation may
only be carried out in case of
extremely cold temperatures and if
the vehicle is parked on a level
surface.
In countries with extreme cold
temperatures it may be necessary to
park the vehicle without applied
parking brake.
This is an emergency operation to
avoid freezing of the parking brake.
140
Driving and operating
Engine exhaust
9 Danger
Engine exhaust gases contain
poisonous carbon monoxide,
which is colourless and odourless
and could be fatal if inhaled.
If exhaust gases enter the interior
of the vehicle, open the windows.
Have the cause of the fault
rectified by a workshop.
Avoid driving with an open load
compartment, otherwise exhaust
gases could enter the vehicle.
As soon as the traffic conditions
permit, regenerate the filter by driving
at a vehicle speed of at least 40 mph
until the control indicator
extinguishes.
Notice
On a new vehicle, the first particle
filter regeneration operations may
be accompanied by a burning smell,
which is normal. Following
prolonged operation of the vehicle at
very low speed or at idle, you may,
in exceptional circumstances, notice
the emission of water vapour at the
exhaust on acceleration. This does
not affect the behaviour of the
vehicle or the environment.
Diesel particle filter
Cleaning process not possible
Automatic cleaning process
If % or H stays on, accompanied
by an audible signal and a message,
this indicates that the particle filter
additive level is too low.
The reservoir must be topped-up
without delay. Seek the assistance of
a workshop.
The diesel particle filter system filters
harmful soot particles out of the
exhaust gases.
The start of saturation of the particle
filter is indicated by the temporary
illumination of % or H,
accompanied by a message in the
Driver Information Centre.
Catalytic converter
The catalytic converter reduces the
amount of harmful substances in the
exhaust gases.
Caution
Fuel grades other than those listed
on pages 3 176, 3 232 could
damage the catalytic converter or
electronic components.
Unburnt petrol will overheat and
damage the catalytic converter.
Therefore avoid excessive use of
the starter, running the fuel tank
dry and starting the engine by
pushing or towing.
In the event of misfiring, uneven
engine running, a reduction in engine
performance or other unusual
problems, have the cause of the fault
rectified by a workshop as soon as
possible. In an emergency, driving
can be continued for a short period,
keeping vehicle speed and engine
speed low.
Driving and operating
AdBlue
Caution
General information
The selective catalytic reduction
(BlueInjection) is a method to
substantially reduce the nitrogen
oxides in the exhaust emission. This
is achieved by injecting a Diesel
Exhaust Fluid (DEF) into the exhaust
system. The ammonia released by
the fluid reacts with nitrous gases
(NOx) from the exhaust and turns it
into nitrogen and water.
The designation of this fluid is
AdBlue®. It is a non-toxic, nonflammable, colourless and odourless
fluid which consists of 32% urea and
68% water.
9 Warning
Avoid contact of your eyes or skin
with AdBlue.
In case of eye or skin contact,
rinse off with water.
Avoid contact of the paintwork with
AdBlue.
In case of contact, rinse off with
water.
AdBlue freezes at a temperature of
approx. -11 °C. As the vehicle is
equipped with an AdBlue pre-heater,
the emissions reduction at low
temperatures is ensured. The AdBlue
pre-heater works automatically.
Level warnings
The AdBlue consumption is
approximately 0.7 litres per
600 miles. The consumption can be
higher depending on driving
behaviour (e.g. high load or towing).
Depending on the calculated range of
AdBlue, different messages are
displayed in the Driver Information
Centre. The messages and the
restrictions are a legal requirement.
141
The first possible warning message
appears at an AdBlue range below
1500 miles, shows up at each start
and each 190 miles range reduction:
Top up AdBlue: Starting impossible in
1500 mi
Additionally, control indicator Y
illuminates continuously and a chime
sounds with every message pop-up.
At an AdBlue range below 380 miles,
the following warning message is
being displayed, shows up at each
start and each 12 miles range
reduction:
Top up AdBlue: Starting impossible in
380 mi
Additionally, control indicator Y
flashes continuously and a chime
sounds with every message pop-up.
Notice
In case of high AdBlue consumption,
the Driver Information Centre may
display this warning without the
previous warning stages.
The last warning level is entered
when the AdBlue tank is empty.
Restart of the engine is not possible.
142
Driving and operating
The following warning message is
being displayed and cannot be
dismissed:
Top up AdBlue: Starting impossible
Additionally, control indicator Y
flashes continuously and engine
cannot be restarted until AdBlue tank
is being filled with at least 5 litres.
High emission warnings
If the exhaust emission rises above a
certain value, warnings similar to the
range warnings will be displayed in
the Driver Information Centre.
Requests to have the exhaust system
checked and finally the
announcement of the prevention of
an engine restart are displayed.
These restrictions are a legal
requirement.
Consult a workshop for assistance.
Refilling AdBlue
Caution
Only use AdBlue that complies
with European standards
DIN 70 070 and ISO 22241-1.
Do not use additives.
Do not dilute AdBlue.
Otherwise the selective catalytic
reduction system could be
damaged.
Notice
Whenever a filling pump with a
nozzle for passenger cars is not
available at a filling station, use only
AdBlue bottles or canisters with a
sealed refill adapter for refilling, to
prevent splashback and overspill,
and in order to ensure that the fumes
from the tank are captured and do
not emerge. AdBlue in bottles or
canisters is available in many filling
stations and can be purchased e.g.
at Vauxhall dealers and other retail
outlets.
Since AdBlue has a limited
durability, check the date of expiry
before refilling.
Notice
When AdBlue-tank is empty, refill at
least five litresto ensure that the new
AdBlue level is being detected.
In case AdBlue refill is not
successfully detected:
1. Continuously drive the vehicle
for ten minutes making sure that
vehicle speed is always higher
than 12 mph.
2. If AdBlue refill is detected
successfully, AdBlue supplydriven warnings or limitations will
disappear.
If AdBlue refill is still not detected,
seek the assistance of a workshop.
If AdBlue must be refilled at
temperatures below -11 °C, the
refilling of AdBlue may not be
detected by the system. In this
event, park the vehicle in a space
with a higher ambient temperature
until AdBlue is liquified.
Driving and operating
Notice
When unscrewing the protective cap
from the filler neck, ammonia fumes
may emerge. Do not inhale as the
fumes have a pungent smell. The
fumes are not harmful by inhalation.
It is recommended to fill the AdBlue
tank completely.
The vehicle must be parked on a level
surface.
The filler neck for AdBlue is located
behind the fuel filler flap, which is
located at left rear side of the vehicle.
The fuel filler flap can only be opened
if the vehicle is unlocked.
1. Remove key from ignition switch.
2. Close all doors to avoid ammonia
fumes entering the interior of the
vehicle.
3. Release the fuel filler flap by
pushing the flap 3 178.
143
9. Unscrew the hose from the filler
neck.
10. Mount the protective cap and turn
clockwise until it engages.
Notice
Dispose of AdBlue canister
according to environmental
requirements. Hose can be reused
after flushing with clear water before
AdBlue dries out.
4. Unscrew protective cap from the
filler neck.
5. Open AdBlue canister.
6. Mount one end of the hose on the
canister and screw the other end
on the filler neck.
7. Lift the canister until it is empty, or
until the flow from the canister has
stopped. This can take up to five
minutes.
8. Place the canister on the ground
to empty the hose, wait 15
seconds.
144
Driving and operating
Automatic transmission
The automatic transmission permits
automatic gearshifting (automatic
mode) or manual gearshifting
(manual mode).
Manual shifting is possible in manual
mode by tapping the selector lever to
+ or - 3 145.
In manual mode, M and the number
of the selected gear is indicated.
R indicates reverse gear.
N indicates neutral position.
P indicates park position.
Selector lever
Transmission display
Move the selector lever in the shifting
gate as shown in the illustration
above.
The mode or selected gear is shown
in the Driver Information Centre.
In automatic mode, the driving
programme is indicated by D.
P : park position, wheels are locked,
engage only when the vehicle is
stationary and the parking brake
is applied
R : reverse gear, engage only when
the vehicle is stationary
N : neutral
D : automatic mode
M : manual mode
< : upshift in manual mode
] : downshift in manual mode
The selector lever is locked in P and
can only be moved when the ignition
is on and the brake pedal is applied.
The engine can only be started with
the lever in position P or N. When
position N is selected, press the brake
pedal or apply the parking brake
before starting.
Do not accelerate while engaging a
gear. Never depress the accelerator
pedal and brake pedal at the same
time.
When a gear is engaged, the vehicle
slowly begins to creep when the
brake is released.
Driving and operating
Engine braking
Manual mode
To utilise the engine braking effect,
select a lower gear in good time when
driving downhill, see manual mode.
R with the number of a higher gear is
indicated, when upshifting is
recommended for fuel saving
reasons.
Shift indication appears only in
manual mode.
Rocking the vehicle is only
permissible if the vehicle is stuck in
sand, mud or snow. Move the selector
lever between D and R in a repeat
pattern. Do not race the engine and
avoid sudden acceleration.
Apply the parking brake and engage
P.
In manual mode, no automatic
shifting to a higher gear takes place
at high engine revolutions.
Gear shift indication
Rocking the vehicle
Parking
145
Move selector lever out of position D
towards the left in position M.
Tap selector lever upwards + to shift
to a higher gear.
Tap the selector lever downwards - to
shift to a lower gear.
If a higher gear is selected when
vehicle speed is too low, or a lower
gear when vehicle speed is too high,
the shift is not executed. This can
cause a message in the Driver
Information Centre.
Electronic driving
programmes
●
●
●
Following a cold start, the
operating temperature
programme increases engine
speed to quickly bring the
catalytic converter to the required
temperature.
Special programmes
automatically adapt the shifting
points when driving up inclines or
down hills.
In snowy or icy conditions or on
other slippery surfaces, the
electronic transmission control
146
Driving and operating
enables the driver to select
manually first, second or third
gear for starting off.
Kickdown
Pressing down the accelerator pedal
beyond the kickdown detent will lead
to maximum acceleration
independent of selected driving
mode. The transmission shifts to a
lower gear depending on engine
speed.
Fault
In the event of a fault a message is
displayed in the Driver Information
Centre. Vehicle messages 3 101.
Electronic transmission control
enables only third gear. The
transmission no longer shifts
automatically.
Do not drive faster than 62 mph.
Have the cause of the fault remedied
by a workshop.
Interruption of power supply
In the event of an interruption of
power supply, the selector lever
cannot be moved out of the P
position. The ignition key cannot be
removed from the ignition switch.
If the vehicle battery is discharged,
start the vehicle using jump leads
3 216.
If the vehicle battery is not the cause
of the fault, release the selector lever.
1. Apply the parking brake.
2. Release the selector lever trim
from the centre console. Poke
with a finger into the leather
socket below the selector lever
and push the trim upwards.
3. Push down the button and move
the selector lever out of P. Have
the cause of the power supply
interruption remedied by a
workshop.
4. Mount the selector lever trim onto
the centre console and refit.
Driving and operating
Manual transmission
147
When clutch slip is detected for a
specific time, the engine power will be
reduced. A warning is displayed in the
Driver Information Centre. Release
the clutch.
Caution
It is not advisable to drive with the
hand resting on the selector lever.
To engage reverse on 5-speed
transmission, depress the clutch
pedal and move the selector lever to
the right and rear.
To engage reverse on 6-speed
transmission, depress the clutch
pedal, pull the ring under the selector
lever and move the selector lever
quite to the left and front.
If the gear does not engage, set the
lever to neutral, release the clutch
pedal and depress again; then repeat
gear selection.
Do not slip the clutch unnecessarily.
When operating, depress the clutch
pedal completely. Do not use the
pedal as a foot rest.
Gear shift indication 3 92.
Stop-start system 3 137.
148
Driving and operating
Brakes
The brake system comprises two
independent brake circuits.
If a brake circuit fails, the vehicle can
still be braked using the other brake
circuit. However, braking effect is
achieved only when the brake pedal
is depressed firmly. Considerably
more force is needed for this. The
braking distance is extended. Seek
the assistance of a workshop before
continuing the journey.
When the engine is not running, the
support of the brake servo unit
disappears once the brake pedal has
been depressed once or twice.
Braking effect is not reduced, but
braking requires significantly greater
force. It is especially important to bear
this in mind when being towed.
Control indicator R 3 91.
ABS starts to regulate brake pressure
as soon as a wheel shows a tendency
to lock. The vehicle remains
steerable, even during hard braking.
ABS control is made apparent
through a pulse in the brake pedal
and the noise of the regulation
process.
For optimum braking, keep the brake
pedal fully depressed throughout the
braking process, despite the fact that
the pedal is pulsating. Do not reduce
the pressure on the pedal.
When braking in an emergency, the
hazard warning flashers are switched
on automatically depending on the
force of deceleration. They are
switched off automatically the first
time you accelerate.
After starting off, the system performs
a self-test which may be audible.
Antilock brake system
Antilock brake system (ABS)
prevents the wheels from locking.
Control indicator u 3 91.
Fault
9 Warning
If there is a fault in the ABS, the
wheels may be liable to lock due
to braking that is heavier than
normal. The advantages of ABS
are no longer available. During
hard braking, the vehicle can no
longer be steered and may
swerve.
Have the cause of the fault remedied
by a workshop.
Parking brake
9 Warning
Before leaving the vehicle, check
parking brake status. Control
indicator R must illuminate
constantly.
Driving and operating
Manual parking brake
9 Warning
Always apply parking brake firmly
without operating the release
button, and apply as firmly as
possible on a downhill or uphill
slope.
To release the parking brake, pull
the lever up slightly, press the
release button and fully lower the
lever.
To reduce the operating forces of
the parking brake, depress the
foot brake at the same time.
149
Control indicator R 3 91.
Ride control systems
Brake assist
Electronic Stability Control
and Traction Control system
If brake pedal is depressed quickly
and forcefully, maximum brake force
is automatically applied.
Operation of brake assist might
become apparent by a pulse in the
brake pedal and a greater resistance
when depressing the brake pedal.
Maintain steady pressure on the
brake pedal as long as full braking is
required. Maximum brake force is
automatically reduced when brake
pedal is released.
Hill start assist
The system helps prevent unintended
movement when driving away on
inclines.
When releasing the brake pedal after
stopping on an incline, brakes remain
on for further two seconds. The
brakes release automatically as soon
as the vehicle begins to accelerate.
Electronic Stability Control improves
driving stability when necessary,
regardless of the type of road surface
or tyre grip.
As soon as the vehicle starts to
swerve (understeer/oversteer),
engine output is reduced and the
wheels are braked individually.
Electronic Stability Control operates
in combination with the Traction
Control system. It prevents the driven
wheels from spinning.
The Traction Control system is a
component of the Electronic Stability
Control.
Traction Control improves driving
stability when necessary, regardless
of the type of road surface or tyre grip,
by preventing the driven wheels from
spinning.
As soon as the driven wheels starts to
spin, engine output is reduced and
the wheel spinning the most is braked
150
Driving and operating
individually. This considerably
improves the driving stability of the
vehicle on slippery road surfaces.
Electronic Stability Control and
Traction Control are operational after
each engine start as soon as the
control indicator b extinguishes.
When Electronic Stability Control and
Traction Control operate, b flashes.
9 Warning
Do not let this special safety
feature tempt you into taking risks
when driving.
Adapt speed to the road
conditions.
Control indicator b 3 92.
Deactivation
applying the brake or in the case that
the vehicle is driven faster than 30
mph.
a extinguishes when Electronic
Stability Control and Traction Control
are reactivated.
Electronic Stability Control and
Traction Control are also reactivated
the next time the ignition is switched
on.
Fault
Electronic Stability Control and
Traction Control can be deactivated,
everytime it is required: press a.
Control indicator a illuminates.
Control indicator a 3 92.
A status message appears in the
Driver Information Centre when
Electronic Stability Control Traction
Control are deactivated.
Electronic Stability Control and
Traction Control are reactivated by
pressing the a button again, by
If there is a fault in the system, the
control indicator b illuminates
continuously and a message appears
in the Driver Information Centre. The
system is not operational.
Have the cause of the fault remedied
by a workshop.
Driving and operating
Driver assistance
systems
9 Warning
Driver assistance systems are
developed to support the driver
and not to replace the driver's
attention.
The driver stays in full control of
the vehicle and accepts full
responsibility when driving the
vehicle.
When using driver assistance
systems, always take care
regarding the current traffic
situation and follow applicable
traffic rules.
Cruise control
The cruise control can store and
maintain speeds above 25 mph.
Additionally at least the third gear
must be engaged on manual
transmission, on automatic
transmission position D or the second
or a higher gear in position M must be
selected.
Deviations from the stored speeds
may occur when driving uphill or
downhill.
The system maintains the vehicle
speed at the preset speed by the
driver, without any action on the
accelerator pedal.
The preset speed can be exceeded
temporarily by pressing the
accelerator pedal.
The status and preset speed is
displayed in the Driver Information
Centre.
Do not use the cruise control if it is not
advisable to maintain a constant
speed.
Activating in first gear is not possible.
Control indicator m 3 94.
151
Switching on
Press m on the steering wheel:
symbol m and Pause are indicated in
the Driver Information Centre. The
system is still not active.
152
Driving and operating
Activation
Setting speed by the driver
Speed value is indicated in the Driver
Information Centre.
Accelerate to the desired speed and
press toggle switch once briefly to
RES/+ or SET/-. The current speed is
stored and maintained. Accelerator
pedal can be released.
The preset speed can then be
changed by pressing toggle switch to
RES/+ to increase or SET/- to
decrease the speed. Short press
changes speed in small steps, long
press in large steps.
Adopting speed by the traffic sign
assistant
The intelligent speed adaptation
informs the driver when a speed limit
is detected by the traffic sign
assistant. If the cruise control is
active, the recognised speed limit will
be displayed in the Driver Information
Centre and "MEM" illuminates.
Press MEM on the steering wheel to
request saving of the suggested
speed.
Press MEM on the steering wheel
once more to confirm and save the
new speed setting.
This speed is the new value for the
cruise control.
This function can be deactivated or
activated in the personalisation
menu, 3 102.
Driving and operating
Exceeding the set speed
Resume stored speed
Vehicle speed can be increased by
depressing the accelerator pedal.
When the accelerator pedal is
released, the previously stored speed
is resumed.
Press toggle switch to RES/+ or Ñ at
a speed above 25 mph. The stored
speed will be obtained.
Deactivation
Press m: the cruise control mode is
deselected and the cruise control
indication extinguishes in the Driver
Information Centre.
Pressing ß to activate the speed
limiter deactivates cruise control.
Switching off the ignition cancels any
programmed speed value.
Press Ñ: cruise control is in pause
mode, Pause is indicated. The
vehicle is driven without cruise
control.
Cruise control is deactivated, but not
switched off. Last stored speed
remains in memory for later speed
resume.
Cruise control is deactivated
automatically:
● The brake pedal is depressed.
● The clutch pedal is depressed.
● Vehicle speed is below 25 mph.
● The Traction Control system or
Electronic Stability Control is
operating.
● The selector lever is in N.
Switching off
153
The driver can accelerate the vehicle
up to the preset speed. Deviations
from the limited speed may occur
when driving downhill.
The preset speed can be exceeded
temporarily by pressing the
accelerator pedal firmly.
The status and preset speed limit is
displayed in the Driver Information
Centre.
Switching on
Fault
In the event of a cruise control fault,
the speed is cleared resulting in
flashing of the dashes.
Speed limiter
The speed limiter prevents the
vehicle exceeding a preset maximum
speed.
The maximum speed can be set at
speeds above 18 mph.
Press ß, symbol ß and Pause are
indicated in the Driver Information
Centre. The system is still not active.
154
Driving and operating
Activation
Setting speed by the driver
Press Ñ to activate speed limiter.
Press toggle switch once briefly to
RES/+ or SET/-.
Following the preset speed can be set
by pressing toggle switch to RES/+ to
increase or SET/- to decrease the
desired maximum speed. Short press
changes preset speed in small steps,
long press in large steps. Speed
value is indicated in the Driver
Information Centre.
Adopting speed by the traffic sign
assistant
The intelligent speed adaptation
informs the driver when a speed limit
is detected by the traffic sign
assistant. If the speed limiter is active,
the recognised speed limit will be
displayed in the Driver Information
Centre and "MEM" illuminates.
Press MEM on the steering wheel to
request saving of the suggested
speed.
Press MEM on the steering wheel
once more to confirm and save the
new speed setting.
This speed is the new value for the
speed limiter.
This function can be deactivated or
activated in the personalisation
menu, 3 102.
Exceeding the speed limit
In the event of an emergency, it is
possible to exceed the speed limit by
a "kickdown". In this case the preset
speed value flashes.
Release the accelerator pedal and
the speed limiter function is
reactivated once a speed lower than
the limit speed is obtained.
Deactivation
Press Ñ: speed limiter is in pause
mode, Pause is indicated. The
vehicle is driven without speed limit.
Driving and operating
Speed limiter is deactivated, but not
switched off. Last stored speed
remains in memory for later speed
resume.
Resume limit speed
Press Ñ. The stored speed limit will
be obtained.
Switching off
Press ß, the speed limiter mode is
deselected and the speed limit
indication extinguishes in the Driver
Information Centre.
Pressing m to activate cruise control
deactivates speed limiter.
The preset speed remains in the
memory when the ignition is switched
off.
Fault
In the event of a speed limiter fault,
the speed is cleared resulting in
flashing of the dashes.
The speed limiter may not operate
correctly if traffic signs do not comply
with the Vienna Convention on Road
Signs and Signals (Wiener
Übereinkommen über
Straßenverkehrszeichen).
Forward collision alert
The forward collision alert may help to
avoid or reduce the harm caused by
front-end crashes.
The forward collision alert uses the
front camera in the windscreen to
detect a vehicle directly ahead, in
your path.
The system triggers different level of
alerts depending on the risk of
collision detected. The alerts are
displayed in the Driver Information
Centre.
Level 1: A visual alert is displayed.
Level 2: A visual alert is displayed and
an audible alert sounds.
Caution
The colour lighting of this control
indicator does not correspond to
local traffic laws on following
distance. The driver bears full
155
responsibility for maintaining safe
following distance according to
applicable traffic rules, weather
and road conditions etc. at all
times.
9 Warning
Forward collision alert is just a
warning system and does not
apply the brakes. When
approaching a vehicle ahead too
rapidly, it may not provide you
enough time to avoid a collision.
The driver accepts full
responsibility for the appropriate
following distance based on traffic,
weather and visibility conditions.
The complete attention of the
driver is always required while
driving. The driver must always be
ready to take action and apply the
brakes.
156
Driving and operating
When the time to a potential collision
with a vehicle in front gets too small
and a collision is imminent, a warning
is displayed in the Driver Information
Centre.
Simultaneously a warning chime
sounds. Depress the brake pedal and
steer the vehicle, if it is required by the
situation.
Operation conditions
The following condition must be
fullfilled for proper operation:
The speed must be between 3 mph
and 87 mph.
Activation
To use forward colision alert, active
safety braking has to be activated in
the vehicle personalisation 3 102.
Selecting the alert sensitivity
The alert sensitivity has to be set to
close, normal or distant in the vehicle
personalisation menu 3 102.
Deactivation
The system can only be deactivated
by deactivating the active emergency
braking in the vehicle personalisation
3 102.
System limitations
Forward collision alert is designed to
warn on vehicles only, but may react
also to other objects.
In the following cases, forward
collision alert may not detect a vehicle
ahead or sensor performance is
limited:
● Driving on winding or hilly roads.
● During nighttime driving.
● Weather limits visibility, such as
fog, rain, or snow
● The windscreen is damaged or
affected by foreign items, e.g.
stickers.
Active emergency braking
Active emergency braking can help to
reduce the damage and injury from
crashes with vehicles, pedestrians
and obstacles directly ahead, when a
collision can no longer be avoided
either by manual braking or by
steering. Before the active
emergency braking applies, the driver
is warned by the forward collision
alert 3 155 or the front pedestrian
protection alert 3 158.
The feature uses various inputs (e.g.
camera sensor, brake pressure,
vehicle speed) to calculate the
probability of a frontal collision.
9 Warning
This system is not intended to
replace the driver responsibility for
driving the vehicle and looking
ahead. Its function is limited to
supplemental use only to reduce
the vehicle speed before a
collision.
The system may not react to
animals. After a sudden lane
change, the system needs a
certain time to detect the next
preceding vehicle.
The driver must always be ready
to take action and apply the brakes
and steer to avoid collisions.
Driving and operating
Operation conditions
Active emergency braking is
equipped with a front camera and
operates in forward gear above
walking speed up to 53 mph.
Activation
Active emergency braking can be
activated in the vehicle
personalisation menu 3 102.
Functionality
The system includes:
● brake preparation system
● emergency automatic braking
● forward looking brake assist
● forward collision alert
● front pedestrian protection
Brake preparation system
When approaching a vehicle ahead
or a pedestrian so quickly that a
collision is likely, the brake
preparation system slightly
pressurizes the brakes. This reduces
the response time, when a manual or
automatic braking is requested.
The brake system is prepared so that
braking can occur more rapidly.
Emergency automatic braking
After activation of brake preparation
system and just before the imminent
collision, this function automatically
applies limited braking to reduce the
impact speed of the collision or
prohibit a crash. Depending on the
situation, the vehicle may
automatically brake moderately or
hard. This front automatic braking can
only occur if a vehicle 3 155 or a
pedestrian 3 158 ahead is detected .
Emergency automatic braking may
slow the vehicle to a complete stop to
try to avoid a potential crash.
9 Warning
Emergency automatic braking is
an emergency crash preparation
feature and is not designed to
avoid crashes. Do not rely on the
system to brake the vehicle.
Emergency automatic braking will
not brake outside of its operating
157
speed range and only responds to
detected vehicles and
pedestrians.
Forward looking brake assist
In addition to the brake preparation
system and emergency automatic
braking, the forward looking brake
assist function makes the brake assist
more sensitive. Therefore, pressing
the brake pedal less strongly results
in immediate hard braking. This
function helps the driver brake
quicker and harder before the
imminent collision.
9 Warning
Active emergency braking is not
designed to apply hard
autonomous braking or to
automatically avoid a collision. It is
designed to reduce the vehicle
speed before a collision. It may not
react to animals. After a sudden
158
Driving and operating
lane change, the system needs a
certain time to detect the next
preceding vehicle.
The complete attention of the
driver is always required while
driving. The driver must always be
ready to take action and apply the
brakes and steer to avoid
collisions.
The system is designed to work with
all occupants wearing their seat belts.
Forward collision alert
3 155
Front pedestrian protection
3 158.
Deactivation
Active emergency braking can be
deactivated in the vehicle
personalisation menu 3 102. If
deactivated a message is displayed
in the Driver Information Centre.
System limitations
In some cases, the active emergency
braking system may provide an
automatic braking in situations that
seem to be unnecessary, for instance
in parking garages, due to traffic signs
in a curve or due to vehicles in
another lane. This is normal
operation, the vehicle does not need
service. Firmly apply the accelerator
pedal to override the automatic
braking if the situation and the
surroundings permit.
In the following cases, active
emergency braking performance is
limited:
● Driving on winding or hilly roads.
● Detecting all vehicles, especially
vehicles with a trailer, tractors,
muddy vehicles, etc.
● Detecting a vehicle when
weather limits visibility, such as in
fog, rain, or snow.
● During nighttime driving.
●
Weather limits visibility, such as
fog, rain, or snow.
● The windscreen is damaged or
affected by foreign items, e.g.
stickers.
Complete attention is always required
while driving, and you should be
ready to take action and apply the
brakes and/or steer the vehicle to
avoid crashes.
Fault
In case the system requires a service,
a message is displayed in the Driver
Information Centre.
If the system does not work as it
should do, vehicle messages are
displayed in the Driver Information
Centre.
Vehicle messages 3 101.
Front pedestrian protection
Front pedestrian protection may help
to avoid or reduce the harm caused
by front-end crashes with nearby
pedestrians when driving in a forward
gear.
Driving and operating
Front pedestrian protection uses the
front camera in the windscreen to
detect a pedestrian directly ahead, in
your path.
The system triggers different level of
alerts depending on the risk of
collision detected. The alerts are
displayed in the Driver Information
Centre.
Level 1: A visual alert is displayed.
Level 2: A visual alert is displayed and
an audible alert sounds.
9 Danger
Front pedestrian braking does not
provide an alert or automatically
brake the vehicle, unless it detects
a pedestrian.
The system may not detect
pedestrians, including children,
when the pedestrian is not directly
ahead, not fully visible, not
standing upright, or when part of a
group.
Caution
The colour lighting of this control
indicator does not correspond to
local traffic laws on following
distance. The driver bears full
responsibility for maintaining safe
following distance according to
applicable traffic rules, weather
and road conditions etc. at all
times.
When the time to a potential collision
with a pedestrian in front gets too
small and a collision is imminent, a
warning is displayed in the Driver
Information Centre.
Simultaneously a warning chime
sounds. Depress the brake pedal and
steer the vehicle, if it is required by the
situation.
Operation conditions
The following condition must be
fullfilled for proper operation:
The speed must be between 3 mph
and 37 mph.
159
Activation
To use the system, active safety
braking has to be activated in the
vehicle personalisation 3 102.
Selecting the alert sensitivity
The alert sensitivity has to be set to
close, normal or distant in the vehicle
personalisation menu 3 102.
Deactivation
The system can only be deactivated
by deactivating the active emergency
braking in the vehicle personalisation,
3 102.
System limitations
Front pedestrian protection is
designed to warn on pedestrians
only, but may react also to other
objects.
In the following cases, the system
may not detect a pedestrian ahead or
sensor performance is limited:
● Driving on winding or hilly roads.
● During nighttime driving.
160
●
●
Driving and operating
Weather limits visibility, such as
fog, rain, or snow
The windscreen is damaged or
affected by foreign items, e.g.
stickers.
rear obstacles. It informs and warns
the driver by giving acoustic signals
and display indication.
Parking assist
General information
When attaching a trailer or bike
carrier to the trailer hitch, the parking
assist is deactivated.
9 Warning
The driver bears full responsibility
for the parking manoeuvre.
Always check the surrounding
area when driving backwards or
forwards while using parking
assist system.
Rear parking assist
The rear parking assist makes
parking easier by measuring the
distance between the vehicle and
The system operates with ultrasonic
parking sensors in the rear bumper.
Activation
Rear parking assist is activated when
reverse gear is engaged and ignition
is switched on.
The system is ready to operate when
the LED in the parking assist button
r OFF does not illuminate.
Indication
The system warns the driver with
acoustic signals against potentially
hazardous obstacles behind the
vehicle in a distance range up to
50 cm while reverse gear is engaged.
Depending on which side of the
vehicle is closer to an obstacle, you
will hear acoustic warning signals in
the vehicle on the respective side.
The interval between the sounds
becomes shorter as the vehicle gets
closer to that obstacle. When the
distance is less than approx. 30 cm,
the sound is continuous.
Driving and operating
Additionally, the distance to rear
obstacles is displayed by changing
distance lines in the Info Display
3 97. When the obstacle is very close,
9 for Danger is displayed in the
screen.
Deactivation
The system is switched off when
reverse gear is disengaged. Press
r OFF to deactivate the system
manually. The LED in the button
illuminates when the system is
deactivated.
Front-rear parking assist
The front-rear parking assist
measures the distance between the
vehicle and obstacles in front and
behind the vehicle. It informs and
warns the driver by giving acoustic
signals and display indication.
It uses two different acoustic warning
signals for the front and rear
monitoring areas, each with a
different tone frequency.
161
Activation
In addition to the rear parking assist,
the front parking assist is triggered
when an obstacle is detected in front
and the speed of the vehicle is still
below 6 mph.
The system is ready to operate when
the LED in the parking assist button
r does not illuminate.
When the system is deactivated, the
LED in the button illuminates.
The system operates with ultrasonic
parking sensors in the rear and front
bumper.
Indication
The system warns the driver with
acoustic signals against potentially
hazardous obstacles in front of the
vehicle and behind the vehicle.
162
Driving and operating
Depending on which side of the
vehicle is closer to an obstacle, you
will hear acoustic warning signals in
the vehicle on the respective side.
The interval between the sounds
becomes shorter as the vehicle gets
closer to that obstacle. When the
distance is less than approx. 30 cm,
the sound is continuous.
Deactivation
The system is deactivated
automatically when vehicle speed
exceeds 6 mph or if the vehicle stops
for more than three seconds in a
forward gear or if no further obstacles
are detected.
Manual deactivation is also possible
by pressing the parking assist button
r.
When the system is deactivated
manually, the LED in the button
extinguishes and a message pops-up
in the Driver Information Centre.
After a manual deactivation, the frontrear parking assist is activated again
if r is pressed or if reverse gear is
engaged.
System limitations
Additionally, the distance to rear and
front obstacles is displayed by
changing distance lines in the InfoDisplay 3 97.
In the event of a fault or if the system
does not work temporarily, e.g.
because of high external noise level
or other interference factors, Service
in the cluster instrument illuminates.
A message is indicated in the Driver
Information Centre.
9 Warning
Under certain circumstances,
various reflective surfaces on
objects or clothing as well as
external noise sources may cause
the system to fail to detect
obstacles.
Special attention must be paid to
low obstacles which can damage
the lower part of the bumper.
Caution
Performance of the system can be
reduced when sensors are
covered, e.g. by ice or snow.
Performance of the parking assist
system can be reduced due to
heavy loading.
Special conditions apply if there
are taller vehicles in the vicinity
(e.g. off-road vehicles, mini vans,
vans). Object identification and
correct distance indication in the
upper part of these vehicles
cannot be guaranteed.
Driving and operating
Objects with a very small reflection
cross-section, e.g. objects of
narrow size or soft materials, may
not be detected by the system.
Parking assist systems do not
detect objects outside the
detection range.
Advanced parking assist
9 Warning
The driver bears full responsibility
for accepting the parking slot
suggested by the system and the
parking manoeuvre.
Always check the surrounding
area in all directions when using
the advanced parking assist.
The advanced parking assist
measures a suitable parking slot
while passing, calculates the
trajectory and automatically steers
the vehicle while parking.
Advanced parking assist provides
assistance for the following
manoeuvres:
● Entry into a parallel parking slot.
● Entry into a perpendicular
parking slot.
● Exit from a parallel parking slot.
The driver must control acceleration,
braking and gear shifting, while
steering is done automatically. The
driver can take control at any time by
gripping the steering wheel.
It may be necessary to move forwards
and backwards more than once.
Instructions are given in the InfoDisplay 3 97.
Advanced parking assist can only be
activated when driving forwards.
163
Advanced parking assist is always
combined with front-rear parking
assist.
The system has six ultrasonic parking
sensors each in both the rear and
front bumper.
Entry into a parallel parking slot
Activation
7'' Colour-Info-Display: to search for a
parking slot, activate the system by
selecting Park Assist on the
homepage of the touch screen. Then
select Enter parallel parking space.
164
Driving and operating
8'' Colour-Info-Display: to search for a
parking slot, activate the system by
pressing Í. Select Driving functions
on the touch screen and then Park
Assist. Select Enter parallel parking
space.
$ illuminates in the instrument cluster
to confirm the function.
Slow down the vehicle speed below
12 mph.
Select parking side by switching on
turn signal indicator on the respective
side.
The allowed parallel distance
between the vehicle and a row of
parked cars is between 0.5 metres
and 1.5 metres.
The system will not identify slots that
are clearly smaller or larger than the
vehicle.
When a free slot is detected, a visual
feedback on the Colour-Info-Display
and a first acoustic signal is given.
Drive slowly forwards. When the
second acoustic signal is given, stop
the vehicle, select reverse gear,
release the steering wheel and start
moving without exceeding 4 mph.
Move forwards and backwards while
observing the warnings of the Parking
assist until the end of manoeuvre is
indicated. When finished, $
extinguishes in the instrument cluster.
Entry into a perpendicular parking
slot
Activation
7'' Colour-Info-Display: to search for a
parking slot, activate the system by
selecting Park Assist on the
homepage of the touch screen. Then
select Enter perpendicular parking
space.
Driving and operating
8'' Colour-Info-Display: when search
for a parking slot, activate the system
by pressing Í. Select Driving
functions on the touch screen and
then Park Assist. Select Enter bay
parking space.
$ illuminates in the instrument cluster
to confirm the function.
Slow down the vehicle speed below
12 mph.
Select parking side by switching on
turn signal indicator on the respective
side.
The allowed parallel distance
between the vehicle and a row of
parked cars is between 0.5 metres
and 1.5 metres.
When several successive slots are
found, the vehicle will be directed
towards the last one.
When a free slot is detected, a visual
feedback on the Colour-Info-Display
and an acoustic signal is given. Stop
the vehicle, select reverse gear,
release the steering wheel and start
moving without exceeding 4 mph.
165
Move forwards and backwards as
instructed by observing the warnings
of the Parking assist and paying
attention to the acoustic signals until
the end of manoeuvre is indicated.
When finished, $ extinguishes in the
instrument cluster.
During the parking manoeuvre, the
system is automatically deactivated
once the rear of the vehicle is within
50 cm of an obstacle.
166
Driving and operating
Exiting a parallel parking slot
Display indication
Activation
7'' Colour-Info-Display: when exiting a
parallel parking slot, activate the
system by selecting Park Assist on
the homepage of the touch screen.
Then select Exit parallel parking
space.
8'' Colour-Info-Display: when exiting a
parallel parking slot, activate the
system by pressing Í. Select Driving
functions on the touch screen and
then Park Assist. Select Exit parallel
parking space.
Select exit side by switching on the
respective turn signal indicator.
Engage reverse or forward gear,
release the steering wheel and start
moving without exceeding 3 mph.
The instructions on the display show:
● General hints and warning
messages.
● The demand to stop the vehicle,
when a parking slot is detected.
● The direction of driving during the
parking manoeuvre.
● The demand to shift into reverse
or first gear.
● The demand to stop or to drive
slowly.
● The successful completion of the
parking manoeuvre indicated by
a pop-up symbol and a chime.
● The cancelling of a parking
manoeuvre.
Move forwards and backwards while
observing the warnings of the Parking
assist until the end of manoeuvre is
indicated. The manoeuvre is
complete when the vehicle's front
wheels are out of the parking slot and
$ extinguishes in the instrument
cluster.
After deactivation check control over
the vehicle.
Deactivation
The current park assist manoeuvre is
cancelled via the button to return to
the previous screen in the ColourInfo-Display. To deactivate the
system completely, press r Off in
the centre console.
Driving and operating
The system is deactivated
automatically:
● if the ignition is switched off
● if stalling the engine
● if no manoeuvre is started within
5 minutes of selection of the type
of manoeuvre
● after a prolonged stop of the
vehicle during a manoeuvre
● if the electronic stability control
(ESC) is triggered
● if the speed of the vehicle
exceeds the stated limit
● when the driver interrupts
movement of the steering wheel
● after 4 manoeuvre cycles
● on opening the driver's door
● if one of the front wheels
encounters an obstacle
● parking manoeuvre successfully
ended
Deactivation by the driver or by the
system during manoeuvring will be
indicated on the display. Additionally,
an acoustic signal sounds.
The system is switched off
automatically when towing a
electrically connected trailer.
Contact your dealer to switch off the
system for a prolonged period.
Fault
In the event of a fault, $ flashes for a
few seconds, accompanied by an
acoustic signal. If the fault occurs
during the use of the system, $
extinguishes.
In the event of a fault in the power
steering, c flashes in the instrument
panel, accompanied by a message.
9 Warning
Under certain circumstances,
various reflective surfaces on
objects or clothing as well as
external noise sources may cause
the system to fail to detect
obstacles.
Special attention must be paid to
low obstacles which can damage
the lower part of the bumper.
167
Caution
Performance of the system can be
reduced when sensors are
covered, e.g. by ice or snow.
Performance of the parking assist
system can be reduced due to
heavy loading.
Special conditions apply if there
are taller vehicles in the vicinity
(e.g. off-road vehicles, mini vans,
vans). Object identification and
correct distance indication in the
upper part of these vehicles
cannot be guaranteed.
Objects with a very small reflection
cross-section, e.g. objects of
narrow size or soft materials, may
not be detected by the system.
Parking assist systems do not
detect objects outside the
detection range.
Notice
It is possible that the sensor detects
a non-existing object caused by
echo disturbance from external
168
Driving and operating
acoustic noise or mechanical
misalignments (sporadic false
warnings may occur).
Make sure that the front number
plate is properly mounted (not bent
and no gaps to the bumper on the left
or right side) and the sensors are
firmly in place.
Advanced parking assist system
may not respond to changes in the
available parking space after
initiating a parking manoeuvre. The
system may recognize an entry, a
gateway, a courtyard or even a
crossing as a parking slot. After
selecting reverse gear the system
will start a parking manoeuvre. Take
care regarding the availability of the
suggested parking slot.
Surface irregularities, e.g. on
construction zones, are not detected
by the system. The driver accepts
responsibility.
Side blind spot alert
The Side blind spot alert system
detects and reports objects on either
side of the vehicle, within a specified
"blind spot" zone. The system
displays a visual alert in each exterior
mirror, when detecting objects that
may not be visible in the interior and
exterior mirrors.
Side blind spot alert uses some of the
advanced parking assist sensors
which are located in the front and rear
bumper on both sides of the vehicle.
9 Warning
8'' Colour-Info-Display: press Í.
Select Driving functions on the touch
screen and then Blind spot
monitoring. System is activated by
viewing on.
B illuminates continously green in the
instrument cluster to confirm the
function.
Functionality
Side blind spot alert does not
replace driver vision.
The system does not detect:
● vehicles outside the side blind
zones which may be rapidly
approaching
● pedestrians, cyclists or animals
Before changing a lane, always
check all mirrors, look over the
shoulder and use the turn signal.
Activation
7'' Colour-Info-Display: select Blind
spot monitoring on the homepage of
the touch screen. System is activated
by viewing W.
When the system detects a vehicle in
the side blind zone while driving
forwards, a round LED will illuminate
in the relevant exterior mirror.
The LED comes on immediately when
being passed.
Driving and operating
The LED comes on after a delay when
passing another vehicle slowly.
Operation conditions
The following conditions must be
fullfilled for proper operation:
● All vehicles are moving in the
same direction and in adjacent
lanes.
● The speed of your vehicle is
between 7 and 87 mph.
● Passing a vehicle with a speed
difference of less than 6 mph.
● Another vehicle is passing with a
speed difference of less than 15
mph.
● The traffic flow is normal.
● Driving on a straight or slightly
curved road.
● The vehicle is not pulling a trailer.
No alert will be given in the following
situations:
● In the presence of non-moving
objects (parked vehicles,
barriers, street lamps, road
signs...).
● With vehicles moving in the
opposite direction.
● Driving on a winding road or a
sharp corner.
● When passing (or being passed
by) a very long vehicle (lorry,
coach...) which is at the same
time detected at the rear in the
blind spot angle and present in
the driver's forward field of vision.
● In very heavy traffic: vehicles
detected in front and behind are
confused with a lorry or a
stationary object.
● When passing too quickly.
Deactivation
The system is deactivated in the
vehicle personalisation 3 102. B
extinguishes in the instrument cluster.
Additionally, an acoustic signal
sounds
169
The state of the system is stored
when switching off the ignition.
The system is automatically
deactivated when towing an
electrically connected trailer.
Fault
In the event of a fault, B flashes for a
few moments in the instrument panel,
accompanied by F and a
display message. Contact a dealer or
a qualified workshop to have the
system checked.
Panoramic view system
This system allows views of the
vehicle's surroundings to be
displayed as a nearly 180° picture in
the Info display, like a bird's eye view.
The system uses:
● rear camera, installed in the
tailgate
● ultrasonic parking sensors in the
rear bumper
The screen in the Info display is
divided into two parts: on the right
there is a view from above the vehicle,
170
Driving and operating
and on the left there is the view from
the rear displayed. The parking
sensors complete the information on
the view from above the vehicle.
Activation
Panoramic view system is activated
by:
● engaging reverse gear
● driving up to 6 mph
Functionality
Different views can be selected in the
left part of the display. Change the
type of view at any time during a
manoeuvre by pressing the touch
field in the left lower zone of the
display:
● Rear view
● Auto mode
● Zoom view
● 180° view
The display is immediately updated
with the type of view selected.
AUTO mode is activated by default. In
this mode, the system selects the
best view, standard or zoom, to
display according to the information
from the parking sensors.
The state of the system is not kept in
memory when the ignition is switched
off.
Rear view
The area behind the vehicle is
displayed in the screen. The vertical
lines represent the width of the
vehicle with mirrors unfolded. The
direction of the lines changes with the
position of the steering wheel.
The first horizontal line represents a
distance of about 30 cm beyond the
edge of vehicle's rear bumper. The
upper horizontal lines represent
distances of about one and two
metres beyond the edge of your
vehicle's rear bumper.
This view is available in AUTO mode
or in the view selection menu.
Driving and operating
Auto mode
This mode is activated by default.
Using sensors in the rear bumper, the
automatic view changes from a rear
view to a view from above, as an
obstacle is approached during a
manoeuvre.
obstacles nearby. This view is
available with AUTO mode or in the
view selection menu.
180° view
Zoom view
171
Deactivation
Panoramic view system is
deactivated when:
● driving faster than 6 mph
● seven seconds after disengaging
reverse gear
● by pressing the icon q in the left
upper corner of the touch screen
● opening the tailgate
General information
9 Warning
The camera records the vehicle's
surroundings during the manoeuvre
in order to reconstruct a view from
above the rear of the vehicle in its
near surroundings, allowing the
vehicle to be manoeuvred around
The 180° view facilitates reversing
out of a parking bay, making it
possible to see the approach of
vehicles, pedestrians and cyclists.
This view is not recommended for
carrying out a complete manoeuvre.
It is made up of three areas: left 1,
centre 2 and right 3. This view is
available from the view selection
menu only.
The panoramic view system does
not replace driver vision. It will not
display children, pedestrians,
cyclists, crossing traffic, animals,
or any other objects outside of the
camera view area, e. g. below the
bumper, or underneath the
vehicle.
Do not drive or park the vehicle
using only the panoramic view
system.
Always check the surrounding of
the vehicle before driving.
172
Driving and operating
Displayed images may be further
or closer than they appear. The
area displayed is limited and
objects that are close to either
edge of the bumper or under the
bumper are not displayed on the
screen.
System limitations
Caution
For optimal operation of the
system, it is important to keep the
lense of the camera in the tailgate
between the number plate lights
always clean. Rinse the lense with
water and wipe with a soft cloth.
Do not clean the lense with a
steam-jet or high-pressure jet
cleaner.
The panoramic view system may not
operate properly when:
● The surrounding is dark.
● The sun or the beam of
headlights is shining directly into
the camera lenses.
●
●
●
●
●
●
During nighttime driving.
Weather limits visibility, such as
fog, rain, or snow.
The camera lenses are blocked
by snow, ice, slush, mud, dirt.
The vehicle is towing a trailer.
The vehicle had an accident.
There are extreme temperature
changes.
Rear view camera
Do not reverse or park the vehicle
using only the rear view camera.
Always check the surrounding of
the vehicle before driving.
Switching on
Rear view camera is automatically
activated when reverse gear is
engaged.
Functionality
The rear view camera assists the
driver when reversing by displaying a
view of the area behind the vehicle.
The view of the camera is displayed
in the Info-Display.
9 Warning
The rear view camera does not
replace driver vision. Note that
objects that are outside the
camera's field of view and the
parking assist sensors, e.g. below
the bumper or underneath the
vehicle, are not displayed.
The camera is mounted above the
licence plate.
Driving and operating
The area displayed by the camera is
limited. The distance of the image that
appears on the display differs from
the actual distance.
Guide lines
edge of your vehicle's rear bumper.
The crossing curves represent the
maximum turning circle.
Deactivation of guide lines
Guide lines can be deactivated in the
Info-Display. Select Settings, I
Vehicle, I Collision detection, I Rear
view camera guide lines, I §.
Info-Display 3 97.
Vehicle personalisation 3 102.
Switching off
The camera is switched off when a
certain forward speed is exceeded or
if reverse gear is disengaged for
approx. 10 seconds.
The vertical lines represent the
general direction of the vehicle and
the distance between the vertical
lines corresponds to the width of your
vehicle without mirrors. The first
horizontal line represents a distance
of about 30 cm beyond the edge of
vehicle's rear bumper. The upper
horizontal lines represent distances
of about 1 and 2 metres beyond the
System limitations
The rear view camera may not
operate properly when:
● The surrounding is dark.
● The beam of headlights is shining
directly into the camera lenses.
● During nighttime driving.
● Weather limits visibility, such as
fog, rain, or snow.
●
●
●
●
●
173
The camera lenses are blocked
by snow, ice, slush, mud, dirt.
Clean the lense, rinse with water,
and wipe with a soft cloth.
The tailgate will be opened.
The vehicle is towing an
electrically connected trailer.
The vehicle had a rear end
accident.
There are extreme temperature
changes.
Lane departure warning
The lane departure warning system
observes the lane markings between
which the vehicle is driving via a front
camera. The system detects lane
changes and warns the driver in the
event of an unintended lane change
via visual and acoustic signals.
Criteria for the detection of an
unintended lane change are:
● No operation of turn signals.
● No brake pedal operation.
● No active accelerator operation
or speeding-up.
174
Driving and operating
If the driver is active, no warning will
be issued.
The system can not operate when no
lane marking is detected.
Activation
System limitations
Deactivation
The system is deactivated by
pressing ½, the LED in the button
illuminates.
At speeds below 37 mph the system
is inoperable.
Fault
The lane departure warning system is
activated by pressing ½. The system
is switched on when the LED in the
button is not illuminated.
The system is only operable at
vehicle speeds above 37 mph and if
lane markings are available.
When the system recognises an
unintended lane change, the control
indicator ) flashes yellow.
Simultaneously a chime sound is
activated.
In the event of a fault, F
appears in the instrument panel,
accompanied by a display message.
Contact a dealer or a qualified
workshop to have the system
checked.
The lane departure warning system
may not operate properly when:
● The windscreen is not clean.
● There are adverse environmental
conditions like heavy rain, snow,
direct sunlight or shadows.
The system performance may not
operate properly when:
● Vehicle speed is below 37 mph.
● Driving on winding or hilly roads.
● During nighttime driving.
● Weather limits visibility, such as
fog, rain, or snow.
● The sensor in the windscreen is
blocked by snow, ice, slush, mud,
dirt, windscreen damage or
affected by foreign items, e.g.
stickers.
● The sun is shining directly into
the camera lens.
● Close vehicles ahead.
● Banked roads.
● Road edges.
● Roads with poor lane markings.
● Sudden lighting changes.
Driving and operating
Driver alert
Driving time alert
The driver alert system monitores the
driving time and the vigilance of the
driver. Monitoring the vigilance of the
driver is based on the trajectory
variations of the vehicle compared to
the lane markings.
The system includes a driving time
alert combined with driver drowsiness
detection.
The driver gets notified by a pop-up
reminder symbol € in the Driver
Information Centre simultaneously
with a acoustic alert if the driver has
not taken a break after two hours of
driving at a speed above 40 mph. The
alert is repeated hourly until the
vehicle is stopped, no matter how
vehicle speed evolves.
The counting of driving time alert is
reset when the ignition has been
switched off for a few minutes.
9 Warning
The system cannot replace the
need for vigilance on the part of
the driver. It is recommended that
you take a break as soon as you
feel tired or at least every two
hours. Do not take the wheel if you
are tired.
Activation or Deactivation
The system can be activated or
deactivated in the vehicle
personalisation 3 102
The state of the system stays in
memory when the ignition is switched
off.
Driver drowsiness detection
The system monitors the driver's level
of vigilance. A camera at the top of the
windscreen detects variations in
trajectory compared to the lane
markings. This system is particularly
suited to fast roads (speed higher
than 40 mph).
If the trajectory of the vehicle
suggests a certain level of
drowsiness or inattention by the
driver, the system triggers the first
175
level of alert. The driver is notified by
a message and an audible signal is
given.
After three first level alerts, the
system triggers a new alert with a
message, accompanied by a more
pronounced audible signal.
In certain driving conditions (poor
road surface or strong winds), the
system may give alerts independent
of the driver's level of vigilance.
The driver drowsiness detection is
reinitialised when the ignition has
been switched off for a few minutes or
the speed remains below 40 mph for
a few minutes.
System limitations
In the following situations, the system
may not operate properly or even not
operate at all:
● Poor visibility caused by
inadequate lighting of the
roadway, falling snow, heavy
rain, dense fog etc.
176
●
●
●
●
●
Driving and operating
Dazzle caused by headlamps of
an oncoming vehicles, low sun,
reflections on damp roads,
leaving a tunnel, alternating
shade and light etc.
Windscreen area in front of the
camera covered by dirt, snow,
stickers etc.
No lane markings detected or
multiple lane markings due to
roadworks
Close vehicles ahead
Winding roads or narrow roads
Fuel
Caution
Fuel for petrol engines
Only use unleaded fuel that complies
with European standard EN 228 or
E DIN 51626-1 or equivalent.
The engine is capable of running with
fuel that contains up to 10% ethanol
(e.g. named E10).
Use fuel with the recommended
octane rating. A lower octane rating
can reduce engine power and torque
and slightly increases fuel
consumption.
Caution
Do not use fuel or fuel additives
that contain metallic compounds
such as manganese-based
additives. This may cause engine
damage.
Use of fuel that does not comply to
EN 228 or E DIN 51626-1 or
equivalent can lead to deposits or
engine damage.
Caution
Use of fuel with a lower octane
rating than the lowest possible
rating could lead to uncontrolled
combustion and engine damage.
The engine specific requirements
regarding octane rating are given in
the engine data overview 3 232. A
country-specific label at the fuel filler
flap can supersede the requirement.
Fuel additives outside Europe
Fuel should contain detergent
additives that help prevent engine
and fuel system deposits from
forming. Clean fuel injectors and
intake valves will allow the emission
control system to work properly.
Driving and operating
Some fuel does not contain sufficient
quantities of additive to keep fuel
injectors and intake valves clean.
To make up for this lack of
detergency, add Fuel System
Treatment PLUS to the fuel tank at
every engine oil change or every
6,000 miles, whichever occurs first. It
is available at your workshop.
Fuels containing oxygenates such as
ethers and ethanol, as well as
reformulated fuel, are available in
some cities. If these fuels comply with
the previously described
specification, then they are
acceptable to use. However, E85
(85% ethanol) and other fuels
containing more than 15% ethanol
must be used only in FlexFuel
vehicles.
Some fuels, mainly high octane
racing fuels, can contain an octane
enhancing additive called
methylcyclopentadienyl manganese
tricarbonyl (MMT). Do not use fuels or
fuel additives with MMT as they can
reduce spark plug life and affect
emission control system
performance. The malfunction
indicator light Z may turn on 3 90. If
this occurs, seek the assistance of a
workshop.
Fuel for diesel engines
Only use diesel fuel that complies
with EN 590.
In countries outside the European
Union use Euro-Diesel fuel with a
sulfur concentration below 50 ppm.
Caution
Caution
Do not use fuel containing
methanol. It can corrode metal
parts in the fuel system and also
damage plastic and rubber parts.
This damage would not be
covered by the vehicle warranty.
Use of fuel that does not comply to
EN 590 or similar can lead to
engine powerloss, increased wear
or engine damage.
177
Do not use marine diesel oils, heating
oils, Aquazole and similar dieselwater emulsions. Diesel fuels must
not be diluted with fuels for petrol
engines.
Low temperature operation
At temperatures below 0° C, some
diesel products with biodiesel blends
may clog, freeze or gel, which may
affect the fuel supply system. Starting
and engine operation may not work
properly. Make sure to fill winter
grade diesel fuel at ambient
temperatures below 0° C.
Arctic grade diesel fuel can be used
in extreme cold temperatures below
-20° C. Using this fuel grade in warm
or hot climates is not recommended
and may cause engine stalling, poor
starting or damage on the fuel
injection system.
Fuel for liquid gas operation
Liquid gas is known as LPG
(Liquefied Petroleum Gas) or under
its French name GPL (Gaz de Pétrole
Liquéfié). LPG is also known as
Autogas.
178
Driving and operating
LPG consists mainly of propane and
butane. The octane rating is between
105 and 115, depending on the
butane proportion. LPG is stored as a
liquid at a pressure of approximately
five to ten bar.
The boiling point depends on the
pressure and the mixing ratio. At
ambient pressure, it is between
-42 °C (pure propane) and -0.5 °C
(pure butane).
Refuelling
Fuel is flammable and explosive.
No smoking. No naked flames or
sparks.
If you can smell fuel in your
vehicle, have the cause of this
remedied immediately by a
workshop.
Caution
Caution
The system works at an ambient
temperature of approx. -8 °C to
100 °C.
Full functioning of the LPG system
can only be guaranteed with liquid
gas which complies with the minimum
requirements of DIN EN 589.
9 Danger
9 Danger
Before refuelling, switch off
ignition and any external heaters
with combustion chambers.
Follow the operating and safety
instructions of the filling station
when refuelling.
In case of misfuelling, do not
switch on ignition.
Fuel filler flap is located at left rear
side of vehicle.
Driving and operating
179
Fuel filler cap
Only use genuine fuel filler caps.
Diesel-engined vehicles have special
fuel filler caps.
The fuel filler flap can only be opened
if the vehicle is unlocked. Release the
fuel filler flap by pushing the flap.
Petrol and Diesel refuelling
To open, turn the cap slowly
anticlockwise.
The fuel filler cap can be attached to
the hook on the fuel filler flap.
To refuel, fully insert the pump nozzle
and switch it on.
After the automatic cut-off, the tank
can be topped up by operating the
pump nozzle a maximum of two more
times.
Caution
Wipe off any overflowing fuel
immediately.
To close, turn the fuel filler cap
clockwise.
Close the flap and allow it to engage.
180
Driving and operating
Trailer hitch
General information
The factory-fitted towing equipment is
folded up under the rear bumper
fascia.
Entrust retrofitting of towing
equipment to a workshop. It may be
necessary to make changes that
affect the cooling system, heat
shields or other equipment. Only use
towing equipment that has been
approved for your vehicle.
To avoid vehicle damage, the power
tailgate cannot be operated with the
radio remote control when a trailer is
electrically connected.
The bulb outage detection function for
trailer brake light cannot detect a
partial bulb outage, e.g. in case of four
times five watt bulbs, the function only
detects lamp outage when only a
single five Watt lamp remains or none
remain.
Fitting of towing equipment could
cover the opening of the towing eye.
If this is the case use the coupling ball
bar for towing.
Driving characteristics and
towing tips
Before attaching a trailer, lubricate
the coupling ball. However, do not do
so if a stabiliser, which acts on the
coupling ball, is being used to reduce
snaking movements.
During trailer towing do not exceed a
speed of 50 mph. A maximum speed
of 60 mph is only appropriate if an
oscillation damper is used and the
permissible gross trailer weight does
not exceed the vehicle's curb weight.
For trailers with low driving stability
and caravan trailers, the use of an
oscillation damper is strongly
recommended.
If the trailer starts snaking, drive more
slowly, do not attempt to correct the
steering and brake sharply if
necessary.
When driving downhill, drive in the
same gear as if driving uphill and
drive at a similar speed.
Adjust tyre pressure to the value
specified for full load 3 238.
Trailer towing
Trailer loads
The permissible trailer loads are
vehicle and engine-dependent
maximum values which must not be
exceeded. The actual trailer load is
the difference between the actual
gross weight of the trailer and the
actual coupling socket load with the
trailer coupled.
The permissible trailer loads are
specified in the vehicle documents. In
general, they are valid for gradients
up to 12%.
The permissible trailer load applies
up to the specified incline and at sea
level. Since engine power decreases
as altitude increases due to the air
becoming thinner, therefore reducing
climbing ability, the permissible gross
train weight also decreases by 10%
for every 1000 metres of altitude. The
gross train weight does not have to be
reduced when driving on roads with
slight inclines (less than 8%, e.g.
motorways).
Driving and operating
The permissible gross train weight
must not be exceeded. This weight is
specified on the identification plate
3 227.
Vertical coupling load
The vertical coupling load is the load
exerted by the trailer on the coupling
ball. It can be varied by changing the
weight distribution when loading the
trailer.
The maximum permissible vertical
coupling load of 60 kg is specified on
the towing equipment identification
plate and in the vehicle documents.
Always aim for the maximum load,
especially in the case of heavy
trailers. The vertical coupling load
should never fall below 25 kg.
181
Rear axle load
When the trailer is coupled and the
towing vehicle fully loaded, the
permissible rear axle load (see
identification plate or vehicle
documents) may be exceeded by
60 kg, the gross vehicle weight rating
must not be exceeded. If the
permissible rear axle load is
exceeded, a maximum speed of
60 mph applies.
Towing equipment
Caution
When operating without a trailer,
remove the coupling ball bar.
Stowage of coupling ball bar
The bag with the coupling ball bar is
stowed on the rear floor cover in the
load compartment.
Place the strap through the rear right
lashing eye, wrap around twice and
tighten the strap to secure the bag.
Fitting the coupling ball bar
182
Driving and operating
Swivel the connecting socket
downwards. Remove the sealing plug
from the opening for the coupling ball
bar and stow it.
Checking the tensioning of the
coupling ball bar
● Red marking on rotary knob must
point towards green marking on
coupling ball bar.
● The gap between the rotary knob
and the coupling ball bar must be
approx. 6 mm.
● The key must be in position c.
Otherwise, the coupling ball bar must
be tensioned before being inserted:
●
Unlock coupling ball bar by
turning key to position c.
●
Pull out rotary knob and turn
clockwise as far as it will go.
Inserting the coupling ball bar
Insert the tensioned coupling ball bar
in the opening and push firmly
upwards until it audibly engages.
The rotary handle snaps back into its
original position resting against the
coupling ball bar without a gap.
9 Warning
Do not touch rotary handle during
insertion.
Lock the coupling ball bar by turning
the key to position e. Remove the key
and close the protective flap.
Driving and operating
Eye for break-away stopping cable
9 Warning
Towing a trailer is permitted only
when a coupling ball bar is fitted
correctly. If the coupling ball bar
does not engage correctly, seek
the assistance of a workshop.
Dismounting the coupling ball bar
Attach breakaway stopping cable to
eye.
Check that the coupling ball bar is
correctly installed
● Green marking on rotary knob
must point towards green
marking on coupling ball bar.
● There must be no gap between
the rotary handle and the
coupling ball bar.
● The coupling ball bar must be
firmly engaged in the opening.
● The coupling ball bar must be
locked and the key removed.
Open the protective flap and turn the
key to position c to unlock the
coupling ball bar.
Pull out rotary handle and turn
clockwise as far as it will go. Pull out
coupling ball bar downwards.
Insert sealing plug in opening.
183
Swivel the connecting socket
upwards.
Stow the coupling ball bar in the bag
and secure by fixing the strap through
the rear right lashing eye. Wrap
around twice and tighten the strap to
secure the bag.
184
Vehicle care
Vehicle care
General Information ................... 184
Accessories and vehicle
modifications .......................... 184
Vehicle storage ........................ 185
End-of-life vehicle recovery ..... 185
Vehicle checks ........................... 186
Performing work ...................... 186
Bonnet ..................................... 186
Engine oil ................................. 187
Engine coolant ......................... 188
Washer fluid ............................ 188
Brakes ..................................... 189
Brake fluid ............................... 189
Vehicle battery ......................... 189
Diesel fuel system bleeding ..... 190
Wiper blade replacement ........ 191
Bulb replacement ....................... 191
Halogen headlights .................. 191
LED headlights ........................ 194
Fog lights ................................. 194
Tail lights ................................. 194
Side turn signal lights .............. 198
Number plate light ................... 199
Interior lights ............................ 199
Instrument panel illumination ... 199
Electrical system ........................ 199
Fuses ....................................... 199
Engine compartment fuse box . 200
Instrument panel fuse box ....... 201
Vehicle tools .............................. 204
Tools ........................................ 204
Wheels and tyres ....................... 204
Winter tyres ............................. 204
Tyre designations .................... 205
Tyre pressure .......................... 205
Tyre deflation detection
system .................................... 206
Tread depth ............................. 207
Changing tyre and wheel size . 208
Wheel covers ........................... 208
Tyre chains .............................. 208
Tyre repair kit .......................... 209
Wheel changing ....................... 212
Spare wheel ............................ 214
Jump starting ............................. 216
Towing ....................................... 217
Towing the vehicle ................... 217
Towing another vehicle ........... 218
Appearance care ....................... 219
Exterior care ............................ 219
Interior care ............................. 221
General Information
Accessories and vehicle
modifications
We recommend the use of genuine
parts and accessories and factory
approved parts specific for your
vehicle type. We cannot assess or
guarantee reliability of other products
- even if they have a regulatory or
otherwise granted approval.
Any modification, conversion or other
changes made to standard vehicle
specifications (including, without
limitation, software modifications,
modifications of the electronic control
units) may invalidate the warranty
offered by Vauxhall. Furthermore,
such changes may affect driver
assistance systems, may impact fuel
consumption, CO2 emissions and
other emissions of the vehicle and
cause the vehicle to no longer
conform to the operating permit,
impacting the validity of your vehicle
registration.
Vehicle care
Caution
When transporting the vehicle on
a train or on a recovery vehicle, the
mud flaps might be damaged.
●
Vehicle storage
●
●
Storage for a long period of time
●
If the vehicle is to be stored for several
months:
● Wash and wax the vehicle.
● Have the wax in the engine
compartment and underbody
checked.
● Clean and preserve the rubber
seals.
● Fill up fuel tank completely.
● Change the engine oil.
● Drain the washer fluid reservoir.
● Check the coolant antifreeze and
corrosion protection.
● Adjust tyre pressure to the value
specified for full load.
Park the vehicle in a dry, well
ventilated place. Engage first or
reverse gear or set selector lever
to P. Prevent the vehicle from
rolling.
Do not apply the parking brake.
Open the bonnet, close all doors
and lock the vehicle.
Disconnect the clamp from the
negative terminal of the vehicle
battery. Beware that all systems
are not functional, e.g. anti-theft
alarm system.
Putting back into operation
When the vehicle is to be put back into
operation:
● Connect the clamp to the
negative terminal of the vehicle
battery. Activate the electronics
of the power windows.
● Check tyre pressure.
● Fill up the washer fluid reservoir.
● Check the engine oil level.
● Check the coolant level.
● Fit the number plate if necessary.
185
End-of-life vehicle recovery
Information on end-of-life vehicle
recovery centres and the recycling of
end-of-life vehicles is available on our
website, where legally required. Only
entrust this work to an authorised
recycling centre.
186
Vehicle care
Vehicle checks
Performing work
9 Danger
The ignition system uses
extremely high voltage. Do not
touch.
Bonnet
Opening
Open the driver's door.
Move the safety catch sideways to the
left vehicle side and open the bonnet.
The bonnet is held open
automatically.
If the bonnet is opened during an
Autostop, the engine will be restarted
automatically for safety reasons.
Stop-start system 3 137.
9 Warning
Only perform engine compartment
checks when the ignition is off.
The cooling fan may start
operating even if the ignition is off.
Closing
Pull the release lever and return it to
its original position.
Lower the bonnet and let it fall into the
latch from a low height (20-25 cm).
Check that the bonnet is engaged.
Vehicle care
187
Caution
Do not press the bonnet into the
latch to avoid dents.
Engine oil
Check the engine oil level manually
on a regular basis to prevent damage
to the engine. Ensure that the correct
specification of oil is used.
Recommended fluids and lubricants
3 225.
The maximum engine oil
consumption is 0.6 litres per
600 miles.
Check with the vehicle on a level
surface. The engine must be at
operating temperature and switched
off for at least five minutes.
Caution
It is the owner's responsibility to
maintain the proper level of an
appropriate quality oil in the
engine.
Pull out the dipstick, wipe it clean,
reinsert it fully, pull out and read the
engine oil level.
When the engine oil level has
dropped to the MIN mark, top up the
engine oil.
Different dipsticks are used
depending on engine variant.
We recommend the use of the same
grade of engine oil that was used at
last change.
188
Vehicle care
the coolant concentration checked
and have the cause of the coolant
loss remedied by a workshop.
The engine oil level must not exceed
the MAX mark on the dipstick.
Caution
Washer fluid
Overfilled engine oil must be
drained or suctioned out.
Capacities 3 237.
Fit the cap on straight and tighten it.
Engine coolant
The coolant provides freeze
protection down to approx. -37 °C.
Caution
Only use approved antifreeze.
Coolant and antifreeze 3 225.
Coolant level
Caution
Too low a coolant level can cause
engine damage.
If the cooling system is cold, the
coolant level should be above the
MIN mark. Top up if the level is low.
9 Warning
Allow the engine to cool before
opening the cap. Carefully open
the cap, relieving the pressure
slowly.
To top up, use a 1:1 mixture of
released coolant concentrate mixed
with clean tap water. If no coolant
concentrate is available, use clean
tap water. Install the cap tightly. Have
Fill with clean water mixed with a
suitable quantity of approved
windscreen washer fluid which
contains antifreeze.
Vehicle care
189
Caution
Only washer fluid with a sufficient
antifreeze concentration provides
protection at low temperatures or
a sudden drop in temperature.
Washer fluid 3 225.
Brakes
In the event of minimum thickness of
the brake lining, a squealing noise
sounds during braking.
Continued driving is possible but
have the brake lining replaced as
soon as possible.
Once new brake linings are installed,
do not brake unnecessarily hard for
the first few journeys.
Brake fluid
9 Warning
Brake fluid is poisonous and
corrosive. Avoid contact with eyes,
skin, fabrics and painted surfaces.
The brake fluid level must be between
the MIN and MAX marks.
If fluid level is below MIN seek the
assistance of a workshop.
Brake and clutch fluid 3 225.
Vehicle battery
The vehicle battery is maintenancefree provided that the driving profile
allows sufficient charging of the
battery. Short-distance-driving and
frequent engine starts can discharge
the battery. Avoid the use of
unnecessary electrical consumers.
Batteries do not belong in household
waste. They must be disposed of at
an appropriate recycling collection
point.
Laying up the vehicle for more than
four weeks can lead to battery
discharge. Disconnect the clamp from
the negative terminal of the vehicle
battery.
Ensure the ignition is switched off
before connecting or disconnecting
the vehicle battery.
Battery discharge protection 3 118.
Disconnecting the battery
If the vehicle's battery is to be
disconnected (e.g. for maintenance
work), the alarm siren must be
deactivated as follows: Switch the
ignition on then off, then disconnect
the vehicle's battery within
15 seconds.
190
Vehicle care
After having reconnected the battery
of a vehicle equipped with an antitheft alarm system, wait 10 minutes
until you start the engine.
Replacing the vehicle battery
Notice
Any deviation from the instructions
given in this section may lead to
temporary deactivation or
disturbance of the stop-start system.
When the vehicle battery is being
replaced, please ensure that there
are no open ventilation holes in the
vicinity of the positive terminal. If a
ventilation hole is open in this area, it
must be closed off with a dummy cap,
and the ventilation in the vicinity of the
negative terminal must be opened.
Ensure that the battery is always
replaced by the same type of battery.
The vehicle battery has to be
replaced by a workshop.
Stop-start system 3 137.
Charging the vehicle battery
9 Warning
On vehicles with stop-start
system, ensure that the charging
potential does not exceed
14.6 volts when using a battery
charger. Otherwise the vehicle
battery might be damaged.
Jump starting 3 216.
Warning label
Meaning of symbols:
● No sparks, naked flames or
smoking.
● Always shield eyes. Explosive
gases can cause blindness or
injury.
● Keep the vehicle battery out of
reach of children.
● The vehicle battery contains
sulphuric acid which could cause
blindness or serious burn
injuries.
● See the Owner's Manual for
further information.
● Explosive gas may be present in
the vicinity of the vehicle battery.
Diesel fuel system bleeding
If the tank has been run dry, the diesel
fuel system must be bled. Switch on
the ignition three times for
15 seconds at a time. Then crank the
engine for a maximum of
40 seconds. Repeat this process after
no less than five seconds. If the
engine fails to start, seek the
assistance of a workshop.
Vehicle care
Wiper blade replacement
Wiper blade on the rear window
191
Bulb replacement
Switch off the ignition and switch off
the relevant switch or close the doors.
Only hold a new bulb at the base. Do
not touch the bulb glass with bare
hands.
Use only the same bulb type for
replacement.
Replace headlight bulbs from within
the engine compartment.
Lift the wiper arm until it stays in the
raised position, press button to
disengage the wiper blade and
remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Lift wiper arm. Disengage wiper blade
as shown in illustration and remove.
Attach the wiper blade slightly angled
to the wiper arm and push until it
engages.
Lower wiper arm carefully.
Bulb check
After a bulb replacement switch on
the ignition, operate and check the
lights.
Halogen headlights
Halogen headlights with separate
housings for low beam and high
beam/turn signal light.
192
Vehicle care
1. Rotate the cap (1) anticlockwise
and remove it.
3. Remove the bulb from the plug
connector by pulling.
4. Replace the bulb and connect it to
the plug connector.
5. Insert and push the bulb holder
into the reflector housing by
setting the lug into position.
6. Fit the cap and rotate clockwise.
Turn signal light
High beam, turn signal light (1)
Low beam (2)
High beam
2. Withdraw the upper bulb holder
from the reflector housing.
1. Rotate the cap (1) anticlockwise
and remove it.
Vehicle care
193
3. Press latch and remove the bulb
from the bulb holder.
4. Replace the bulb and attach it to
the bulb holder.
5. Insert the bulb holder into the
reflector housing and rotate
clockwise.
6. Fit the cap and rotate clockwise.
Low beam
2. Lift the retainer, then pull the plug
connector backwards.
3. Fold down the retainer and
remove the bulb from the reflector
housing.
2. Rotate the lower bulb holder
anticlockwise to disengage.
Withdraw the bulb holder from the
reflector housing.
1. Rotate the cap (2) anticlockwise
and remove it.
194
Vehicle care
2. Disengage the bulb socket from
the plug connector by pressing
the retaining lug.
3. Remove and replace the bulb
socket with bulb and attach the
plug connector.
4. Insert the bulb socket into the
reflector housing by turning
clockwise and engage.
4. Replace the bulb and push it into
the reflector housing by setting
the lug into position.
5. Fold up the retainer and hold in
position.
6. Attach the plug connector to the
bulb and fix it with the retainer.
7. Fit the cap and rotate clockwise.
Sidelight/Daytime running light
In case of defective LEDs, have them
replaced by a workshop.
LED headlights
Headlights for low and high beam,
sidelights, daytime running lights and
turn signal lights are designed as
LEDs and can not be changed.
Have lights repaired by a workshop in
case of failure.
Fog lights
The bulbs are accessible from the
underside of the vehicle.
Tail lights
1. Turn the bulb holder anticlockwise and remove it from the
reflector housing.
Depending on version, tail lights and
brake lights are designed as LEDs. In
case of failure, have LEDs replaced
by a workshop.
Vehicle care
Light assembly in the body
Detaching the light assembly
1. Unscrew the two screws that
secure the light assembly.
2. Remove the light assembly by
pulling it straight back.
195
Remove the bulb by pulling and
replace.
Tail light/Brake light 1
Turn-signal light 2
Version with LED
Only turn signal light bulb can be
replaced.
3. Remove the three screws that
secure the bulb carrier.
4. Version without LED
Remove the bulb socket from the
light assembly by turning it
anticlockwise.
196
Vehicle care
Light assembly in the tailgate
Detaching the light assembly
Remove the turn signal light bulb
from the socket by pulling it
straight out.
Replace bulb.
Attaching the light assembly
1. Attach the bulb carrier to the light
assembly and secure with the
three screws.
2. Attach the light assembly to the
vehicle body as shown in the
illustration and secure with the
two screws.
1. Release the cover in the tailgate
and remove it.
Vehicle care
2. Unscrew the plastic securing nut
by hand.
3. Carefully withdraw the light
assembly from the recesses and
remove.
197
4. Press latch to release and remove
bulb carrier.
5. Version without LED
Remove the bulb socket from the
light assembly by turning it
anticlockwise.
Remove and replace the bulb:
Tail light 1
Rear fog light (right side), reverse
light (left side) 2
Version with LED
Only reverse light bulb can be
replaced.
Remove the bulb from the socket
by pulling it straight out.
198
Vehicle care
Replace bulb.
Attaching the light assembly
1. Attach bulb carrier to the light
assembly.
Side turn signal lights
To replace bulb, remove lamp
housing:
2. Turn bulb holder anticlockwise
and remove from housing.
2. Attach the light assembly to the
tailgate.
3. Secure the light assembly with the
plastic securing nut.
4. Attach the cover to the tailgate.
1. Slide lamp to its left side and
remove with its right end.
3. Pull bulb from bulb holder and
replace it.
Vehicle care
4. Insert bulb holder and turn
clockwise.
5. Insert left end of the lamp, slide to
the left and insert right end.
Number plate light
The number plate light is designed as
LEDs and can not be changed. In
case of defective LEDs, have them
replaced by a workshop.
Interior lights
Courtesy light, reading lights
Have bulbs replaced by a workshop.
Load compartment light
Have bulbs replaced by a workshop.
Instrument panel
illumination
Have bulbs replaced by a workshop.
199
Electrical system
Fuses
Data on the replacement fuse must
match the data on the defective fuse.
There are three fuse boxes in the
vehicle:
● engine compartment
● instrument panel
Before replacing a fuse, turn off the
respective switch and the ignition.
A blown fuse can be recognised by its
melted wire.
Caution
Do not replace the fuse until the
cause of the fault has been
remedied.
Some functions are protected by
several fuses.
Fuses may also be inserted without
existence of a function.
Fuse extractor
A fuse extractor may be located in the
fuse box in the engine compartment.
200
Vehicle care
Engine compartment fuse
box
No. Circuit
The fuse box is in the front left of the
engine compartment.
Disengage the cover and remove it.
Place the fuse extractor on the
various types of fuse from the top or
side, and withdraw fuse.
1
Fan climate control system
2
–
3
Body fuse box
4
–
5
Instrument panel fuse box
6
Engine cooling unit
7
Body control module
8
Engine control fuel pump
9
Engine control
Vehicle care
201
No. Circuit
No. Circuit
Instrument panel fuse box
10
Engine control
27
Body control module
11
Engine control
28
Engine control module
Fuse box on the left side of the
instrument panel
12
Engine cooling unit
29
Front wiper
13
Body control module
30
Body control module
14
Intelligent battery sensor
15
–
16
Front fog light
17
–
After having changed defective fuses,
close the fuse box cover and press
until it engages.
If the fuse box cover is not closed
correctly, malfunction may occur.
18
High beam right
19
High beam left
20
Engine control fuel pump
21
Starter
22
–
23
Starter
24
Trailer hitch
25
Instrument panel fuse box
26
Transmission control module
In right-hand drive vehicles, the fuse
box is located behind a cover in the
glovebox. Open the glovebox and
remove the cover.
202
Vehicle care
No. Circuit
No. Circuit
6
Windscreen washer pump front/
rear
21 Anti-theft alarm system / Start
button
7
Heated steering wheel
22 Rain sensor / Camera
8
Rear wiper
23 Door module
9
–
24 Advanced parking assist /
Camera / Infotainment
10 Central locking system
11 Central locking system
No. Circuit
12 Instrument cluster
1
Interior mirror / Exhaust
system / Electric power
steering / Clutch sensor / LPG /
Exterior mirror adjustment /
Inductive charging
13 Climate control system / USB
2
–
3
Trailer Hitch
16 Brake / Starter / Retained power
off
4
Horn
5
Windscreen washer pump front/
rear
14 OnStar
15 Instrument cluster / Climate
control system
17 Instrument cluster
18 Advanced parking assist
19 Top column module / Trailer
control module
20 –
25 Airbag
26 Top column module
27 Anti-theft alarm system
28 –
29 Infotainment
30 –
31 Infotainment
32 Power outlet front
33 –
34 Heated exterior mirrors / Door
module
Vehicle care
No. Circuit
No. Circuit
35 Instrument cluster / Light
switch / Advanced parking
assist/ Transmission control
module
10
Power outlet rear
11
–
12
–
36 Courtesy lights / Sunvisor
lights / Glovebox light
Fuse box on the right side of the
instrument panel
No. Circuit
In right-hand drive vehicles, the fuse
box is behind a cover in the
instrument panel. Disengage cover at
the side and remove.
1
Heated rear window
2
Heated exterior mirrors
3
Front power window
4
Driver's door control unit
5
Rear power window
6
Heated seats
7
–
8
Infotainment
9
–
203
204
Vehicle care
Vehicle tools
Vehicles without spare wheel
Tools
Tyre condition, wheel condition
Vehicles with spare wheel
The jack, tools, a strap for securing a
damaged wheel and the towing eye
are placed in the tool box in the right
wall of the load compartment. Spare
wheel 3 214.
Wheels and tyres
Drive over edges slowly and at right
angles if possible. Driving over sharp
edges can cause tyre and wheel
damage. Do not trap tyres on the kerb
when parking.
Regularly check the wheels for
damage. Seek the assistance of a
workshop in the event of damage or
unusual wear.
The screwdriver and the towing eye
are located in a box below the floor
cover in the load compartment.
Tyre repair kit 3 209.
Winter tyres
Winter tyres improve driving safety at
temperatures below 7 °C and should
therefore be fitted on all wheels.
In accordance with country-specific
regulations, affix the speed sticker in
the driver's field of view.
All tyre sizes are permitted as winter
tyres 3 238.
Vehicle care
Tyre designations
Directional tyres
E.g. 195/65 R 15 91 T
195 : tyre width, mm
65 : cross-section ratio (tyre height
to tyre width), %
R : belt type: Radial
RF : type: RunFlat
15 : wheel diameter, inches
91 : load index e.g. 95 is equivalent
to 615 kg
T
: speed code letter
Directional tyres should be mounted
so that they rotate in the correct
direction. The proper rotation
direction is indicated by a symbol
(e.g. an arrow) on the sidewall.
Speed code letter:
Q : up to 100 mph
S : up to 112 mph
T : up to 118 mph
H : up to 130 mph
V : up to 150 mph
W : up to 168 mph
Choose a tyre appropriate for the
maximum speed of your vehicle.
The maximum speed is achievable at
kerb weight with driver (75 kg) plus
125 kg payload. Optional equipment
could reduce the maximum speed of
the vehicle.
Performance 3 234.
Tyre pressure
Check the pressure of cold tyres at
least every 14 days and before any
long journey. Do not forget the spare
wheel. This also applies to vehicles
with tyre pressure monitoring system.
Tyre pressure 3 238.
205
The tyre pressure information label
on the left door frame indicates the
original equipment tyres and the
correspondent tyre pressures.
The tyre pressure data refers to cold
tyres. It applies to summer and winter
tyres.
Always inflate the spare tyre to the
pressure specified for full load.
The ECO tyre pressure serves to
achieve the smallest amount of fuel
consumption possible.
Incorrect tyre pressures will impair
safety, vehicle handling, comfort and
fuel economy and will increase tyre
wear.
Tyre pressures differ depending on
various options. For the correct tyre
pressure value, follow the procedure
below:
1. Identify drive axle and body style.
2. Identify the engine identifier code.
Engine data 3 232.
3. Identify the respective tyre.
The tyre pressure tables show all
possible tyre combinations 3 238.
206
Vehicle care
For the tyres approved for your
vehicle, refer to the EEC Certificate of
Conformity provided with your vehicle
or other national registration
documents.
The driver is responsible for correct
adjustment of tyre pressure.
9 Warning
If the pressure is too low, this can
result in considerable tyre warmup and internal damage, leading to
tread separation and even to tyre
blow-out at high speeds.
9 Warning
For specific tyres the
recommended tyre pressure as
shown in the tyre pressure table
may exceed the maximum tyre
pressure as indicated on the tyre.
Never exceed the maximum tyre
pressure as indicated on the tyre.
Temperature dependency
The tyre pressure depends on the
temperature of the tyre. During
driving, tyre temperature and
pressure increase. Tyre pressure
values provided on the tyre
information label and tyre pressure
chart are valid for cold tyres, which
means at 20 °C.
The pressure increases by nearly
1.5 psi for a 10 °C temperature
increase. This must be considered
when warm tyres are checked.
Tyre deflation detection
system
The tyre deflation detection system
continually checks the rotation speed
of all four wheels and warns on low
tyre pressure condition once vehicle
is driving. This is achieved by
comparing tyre rolling circumference
with reference values.
If a tyre loses pressure the control
indicator w illuminates and a warning
message is displayed in the Driver
Information Centre.
In this case reduce speed, avoid
sharp cornering and strong braking.
Stop at next safe opportunity and
check tyre pressure.
Control indicator w 3 93.
After adjusting tyre pressure initialise
system to extinguish the control
indicator and restart system.
Caution
Deflation detection system warns
just about low tyre pressure
condition and does not replace
regular tyre maintenance by the
driver.
In case of a system malfunction a
message is displayed in the Driver
Information Centre. Set correct tyre
pressure and reinitialise system. If the
failure continues to be displayed,
contact a workshop. The system is
inoperable when ABS or ESC has a
malfunction or a temporary spare
wheel is used. Once the road tyre has
been refitted, check the tyre pressure
with cold tyres and initialise the
system.
Vehicle care
System initialisation
After tyre pressure correction or
wheel change, the system must be
initialised to learn new circumference
reference values:
1. Always ensure that all four tyres
have correct tyre pressure
3 238.
2. Apply manual parking brake.
3. Press w to reset deflation
detection system.
4. Reset is confirmed by pop-up
indication.
After initialisation system
automatically calibrates to new tyre
pressures during driving. After longer
drive the system will adopt and
monitor new pressures.
Always check tyre pressure with cold
tyres.
System has to be reinitialised when:
● Tyre pressure has been changed
● Load condition has been
changed
● Wheels have been swapped or
exchanged
The system will not warn
instantaneously on a tyre blow out or
a rapid deflation. This is due to
required calculation time.
Tread depth
Check tread depth at regular
intervals.
Tyres should be replaced for safety
reasons at a tread depth of 2-3 mm
(4 mm for winter tyres).
207
For safety reasons, it is
recommended that the tread depth of
the tyres on one axle should not vary
by more than 2 mm.
The legally permissible minimum
tread depth (1.6 mm) has been
reached when the tread has worn
down as far as one of the tread wear
indicators (TWI). Their position is
indicated by markings on the
sidewall.
If there is more wear at the front than
the rear, swap round front wheels and
rear wheels periodically. Ensure that
the direction of rotation of the wheels
remains the same.
208
Vehicle care
Tyres age, even if they are not used.
We recommend tyre replacement
every 6 years.
Changing tyre and wheel
size
If tyres of a different size than those
fitted at the factory are used, it may be
necessary to reprogramme the
speedometer as well as to reinitialise
the tyre deflation detection system
and make other vehicle modifications.
Tyre deflation detection system
3 206.
Have the label with tyre pressures
replaced.
9 Warning
The use of unsuitable tyres or
wheels may lead to accidents and
will invalidate the vehicle
operating permit.
Wheel covers
Tyre chains
Wheel covers and tyres that are
factory approved for the respective
vehicle and comply with all of the
relevant wheel and tyre combination
requirements must be used.
If the wheel covers and tyres used are
not factory approved, the tyres must
not have a rim protection ridge.
Wheel covers must not impair brake
cooling.
9 Warning
Use of unsuitable tyres or wheel
covers could lead to sudden
pressure loss and thereby
accidents.
Vehicles with steel wheels: When
using locking wheel nuts, do not
attach wheel covers.
Tyre chains are only permitted on the
front wheels.
Always use fine mesh chains that add
no more than 10 mm to the tyre tread
and the inboard sides (including chain
lock).
9 Warning
Damage may lead to tyre blowout.
Tyre chains are only permitted on
tyres of size 195/65 R15 91 and
195/60 R16 89
Temporary spare wheel
Vehicle care
209
The use of tyre chains is not permitted
on the temporary spare wheel.
Tyre repair kit
Minor damage to the tyre tread can be
repaired with the tyre repair kit.
Do not remove foreign bodies from
the tyres.
Tyre damage exceeding 4 mm or that
is at tyre's sidewall cannot be repaired
with the tyre repair kit.
9 Warning
Do not drive faster than 50 mph.
Do not use for a lengthy period.
Steering and handling may be
affected.
If you have a flat tyre:
Apply the parking brake and engage
first gear, reverse gear or P.
The tyre repair kit is in the load
compartment below the floor cover.
1. Remove the sealant bottle and the
compressor.
2. Pull speed limit label from sealant
bottle and place it in driver's
visible area.
3. Remove the electrical connection
cable and air hose from the
stowage compartments on the
underside of the compressor.
210
Vehicle care
4. Screw the compressor air hose to
the connection on the sealant
bottle.
5. Fit the sealant bottle into the
bracket on the compressor.
Set the compressor near the tyre
in such a way that the sealant
bottle is upright.
6. Unscrew valve cap from defective
tyre.
7. Screw the filler hose to the tyre
valve.
8. The switch on the compressor
must be set to J.
9. Connect the compressor plug to
the power outlet or cigarette
lighter socket.
To avoid discharging the battery,
we recommend running the
engine.
10. Set the rocker switch on the
compressor to I. The tyre is filled
with sealant.
11. The compressor pressure gauge
briefly indicates up to 6 bar whilst
the sealant bottle is emptying
(approx. 30 seconds). Then the
pressure starts to drop.
12. All of the sealant is pumped into
the tyre. Then the tyre is being
inflated.
13. The prescribed tyre pressure
should be obtained within ten
minutes.
Tyre pressure 3 238.
When the correct pressure is
obtained, switch off the
compressor.
If the prescribed tyre pressure is
not obtained within ten minutes,
remove the tyre repair kit. Move
the vehicle one tyre rotation.
Reattach the tyre repair kit and
continue the filling procedure for
ten minutes. If the prescribed tyre
pressure is still not obtained, the
tyre is too badly damaged. Seek
the assistance of a workshop.
Vehicle care
211
Repeat the checking procedure
once more after driving further
three miles (but no more than ten
minutes) to check that there is no
more loss of pressure.
If the tyre pressure has fallen
below 1.5 bar, the vehicle must
not be used. Seek the assistance
of a workshop.
17. Stow away tyre repair kit in load
compartment.
Drain excess tyre pressure with
the button on the air hose.
Do not run the compressor longer
than ten minutes.
14. Detach the tyre repair kit. Remove
sealant bottle from bracket. Screw
the filler hose to the free
connection of the sealant bottle.
This prevents sealant from
escaping. Stow tyre repair kit in
load compartment.
15. Remove any excess sealant
using a cloth.
16. Continue driving immediately so
that sealant is evenly distributed
in the tyre. After driving approx.
three miles (but no more than ten
minutes), stop and check tyre
pressure. Screw compressor air
hose directly onto tyre valve when
doing this. Fill tyre as described
before. Drain excess tyre
pressure with the button on the air
hose.
If tyre pressure hasn't decreased
under 1.5 bar, set it to the correct
value. Otherwise the vehicle must
not be used. Seek assistance of a
workshop.3 238
Notice
The driving characteristics of the
repaired tyre are severely affected,
therefore have this tyre replaced.
If unusual noise is heard or the
compressor becomes hot, turn
compressor off for at least
30 minutes.
The built-in safety valve opens at a
pressure of seven bar (102 psi).
Note the expiry date of the kit. After
this date its sealing capability is no
longer guaranteed. Pay attention to
storage information on sealant
bottle.
212
Vehicle care
Replace the used sealant bottle.
Dispose of the bottle as prescribed
by applicable laws.
The compressor and sealant can be
used from approx. -30 °C.
Wheel changing
Some vehicles are equipped with a
tyre repair kit instead of a spare wheel
3 209.
Make the following preparations and
observe the following information:
● Park the vehicle on a level, firm
and non-skid surface. The front
wheels must be in the straightahead position.
● Apply the parking brake and
engage first gear, reverse gear or
P.
● Remove the spare wheel 3 214.
● Never change more than one
wheel at once.
● Use the jack only to change
wheels in case of puncture, not
for seasonal winter or summer
tyre change.
● The jack is maintenance-free.
●
●
●
●
●
●
If the ground on which the vehicle
is standing is soft, a solid board
(max. 1 cm thick) should be
placed under the jack.
Take heavy objects out of the
vehicle before jacking up.
No people or animals may be in
the vehicle when it is jacked-up.
Never crawl under a jacked-up
vehicle.
Do not start the vehicle when it is
raised on the jack.
Before screwing in the wheel
bolts, clean them.
9 Warning
Do not grease wheel bolts.
9 Warning
Ensure to use always the correct
wheel bolts if changing the
wheels. When installing the spare
wheel, the bolts for alloy wheels
can also be used.
●
Note that the spare wheel is
secured by the conical contact of
each bolt if the wheel bolts for the
alloy wheels are used. In this
case, the washers do not come
into contact with the spare wheel.
1. Disengage wheel bolt caps with a
screwdriver and remove.
Steel wheels with cover: Pull off
the wheel cover.
Alloy wheels: Disengage wheel
bolt caps with a screwdriver and
remove. To protect the wheel,
place a soft cloth between the
screwdriver and the alloy wheel.
Vehicle care
213
the jacking point in a manner that
prevents it from slipping.
2. Fold out the wheel wrench and
install ensuring that it locates
securely and loosen each wheel
bolt by half a turn.
The wheels might be protected by
locking wheel bolts. To loosen
these specific bolts, first attach
the adapter for the locking wheel
bolts onto the head of the bolt
before installing the wheel
wrench. The adapter is located in
the load compartment under the
rear floor cover.
3. Ensure the jack is correctly
positioned under the relevant
vehicle jacking point.
4. Set the jack to the necessary
height. Position it directly below
Ensure that the edge of the body
fits into the notch of the jack.
214
5.
6.
7.
8.
9.
10.
Vehicle care
Attach wheel wrench and with the
jack correctly aligned rotate wheel
wrench until wheel is clear of the
ground.
Unscrew the wheel bolts.
Change the wheel. Spare wheel
3 214.
Screw on the wheel bolts.
Lower vehicle.
Install the wheel wrench ensuring
that it is located securely and
tighten each bolt in a crosswise
sequence. Tightening torque is
100 Nm for all wheels.
If the vehicle is equipped with
alloy wheels, note that the wheel
bolts can also be used for the steel
spare wheel. In this case, the
spare wheel is secured by the
conical contact of each bolt.
Align the valve hole in the wheel
cover with the tyre valve before
installing.
Install wheel bolt caps.
11. Stow and secure the replaced
wheel 3 214, the vehicle tools
3 204 and the adapter for the
locking wheel bolts 3 64.
12. Check the tyre pressure of the
installed tyre and the wheel bolt
torque as soon as possible.
Have the defective tyre renewed or
repaired as soon as possible.
Jacking position for lifting platform
Front arm position of the lifting
platform at the underbody.
Spare wheel
Mounting the temporary spare
wheel
Rear arm position of the lifting
platform at the underbody.
Only mount one temporary spare
wheel. Do not drive faster than
50 mph. Take curves slowly. Do not
use for a long period of time.
Vehicle care
Caution
The use of a spare wheel that is
smaller than the other wheels or in
combination with winter tyres
could affect driveability. Have the
defective tyre replaced as soon as
possible.
The temporary spare wheel has a
steel rim.
The temporary spare wheel is located
in the load compartment beneath the
floor covering.
To remove:
1. Open the floor cover.
2. The temporary spare wheel is
secured with a wing nut. Turn
wing nut anticlockwise and
remove the wheel.
There is a box with tools in the
right wall of the load
compartment. Vehicle tools3 204
3. When, after a wheel change, no
wheel is placed in the spare wheel
well, secure the tool box by
turning right back the wing nut and
close the floor cover.
4. After a wheel change back to a full
size wheel, place the spare wheel
outside up in the well and secure
with the wing nut.
If your vehicle gets a flat tyre on the
rear while towing another vehicle,
mount the temporary spare wheel in
the front and the full tyre in the rear.
Tyre chains 3 208.
Stowing a damaged full size
wheel in the load compartment
The spare wheel well is not designed
for other tyre sizes than the temporary
spare wheel. A damaged full size
wheel must be stowed in the load
215
compartment and secured with a
strap. Vehicle tools 3 204. To secure
the wheel:
1. Position the wheel outside up
close to one sidewall of the load
compartment.
2. Place the loop end of the strap
through the front lashing eye on
the appropriate side.
3. Place the hook end of the strap
through the loop and pull it until
the strap is fastened securely to
the lashing eye.
216
Vehicle care
Jump starting
●
Do not start with quick charger.
A vehicle with a discharged vehicle
battery can be started using jump
leads and the vehicle battery of
another vehicle.
●
9 Warning
4. Insert the strap through the
spokes of the wheel as shown in
the illustration.
5. Mount the hook to the rear lashing
eye.
6. Tighten the strap and secure it
using the buckle.
9 Danger
Always drive with folded up and
engaged rear seat backrests when
stowing a damaged full size wheel
in the load compartment.
Be extremely careful when starting
with jump leads. Any deviation
from the following instructions can
lead to injuries or damage caused
by battery explosion or damage to
the electrical systems of both
vehicles.
9 Warning
Avoid contact of the battery with
eyes, skin, fabrics and painted
surfaces. The fluid contains
sulphuric acid which can cause
injuries and damage in the event
of direct contact.
●
Never expose the vehicle battery
to naked flames or sparks.
●
●
●
●
●
●
A discharged vehicle battery can
already freeze at a temperature
of 0 °C. Defrost the frozen battery
before connecting jump leads.
Wear eye protection and
protective clothing when
handling a battery.
Use a booster battery with the
same voltage (12 Volts). Its
capacity (Ah) must not be much
less than that of the discharged
vehicle battery.
Use jump leads with insulated
terminals and a cross section of
at least 16 mm2 (25 mm2 for
diesel engines).
Do not disconnect the discharged
vehicle battery from the vehicle.
Switch off all unnecessary
electrical consumers.
Do not lean over the vehicle
battery during jump starting.
Do not allow the terminals of one
lead to touch those of the other
lead.
Vehicle care
●
●
The vehicles must not come into
contact with each other during
the jump starting process.
Apply the parking brake,
transmission in neutral,
automatic transmission in P.
Open the positive terminal protection
caps of both vehicle batteries.
Lead connection order:
1. Connect the red lead to the
positive terminal of the booster
battery.
2. Connect the other end of the red
lead to the positive terminal of the
discharged battery.
3. Connect the black lead to the
negative terminal of the booster
battery.
4. Connect the other end of the black
lead to a vehicle grounding point
of your vehicle in the engine
compartment.
Route the leads so that they cannot
catch on rotating parts in the engine
compartment.
To start the engine:
1. Start the engine of the vehicle
providing the jump.
2. After five minutes, start the other
engine. Start attempts should be
made for no longer than
15 seconds at an interval of one
minute.
3. Allow both engines to idle for
approx. three minutes with the
leads connected.
4. Switch on electrical consumers
(e.g. headlights, heated rear
window) of the vehicle receiving
the jump start.
5. Reverse above sequence exactly
when removing leads.
217
Towing
Towing the vehicle
Insert a screwdriver in the slot at the
bottom of the cap. Release the cap by
carefully moving the screwdriver
downwards.
The towing eye is stowed with the
vehicle tools 3 204.
218
Vehicle care
Caution
Towing another vehicle
Drive slowly. Do not drive jerkily.
Excessive tractive force can
damage the vehicle.
Screw in the towing eye as far as it will
go until it stops in a horizontal
position.
Attach a tow rope – or better still a tow
rod – to the towing eye.
The towing eye must only be used for
towing and not for recovering the
vehicle.
Switch on ignition to release steering
wheel lock and to permit operation of
brake lights, horn and windscreen
wiper.
Switch the selector lever to neutral.
Release the parking brake.
When the engine is not running,
considerably more force is needed to
brake and steer.
To prevent the entry of exhaust gases
from the towing vehicle, switch on the
air recirculation and close the
windows.
Vehicles with automatic transmission:
The vehicle must be towed facing
forwards, not faster than 50 mph nor
further than 60 miles. In all other
cases and when the transmission is
defective, the front axle must be
raised off the ground.
Seek the assistance of a workshop.
After towing, unscrew the towing eye.
Insert cap with the outer flange into
the recess and fix cap by pushing.
Insert a screwdriver in the slot at the
bottom of the cap. Release the cap by
carefully moving the screwdriver
downwards.
The towing eye is stowed with the
vehicle tools 3 204.
Vehicle care
Caution
Drive slowly. Do not drive jerkily.
Excessive tractive force can
damage the vehicle.
After towing, unscrew the towing eye.
Insert cap with the upper flange into
the recess and fix cap by pushing.
Screw in the towing eye as far as it will
go until it stops in a horizontal
position.
The lashing eye at the rear
underneath the vehicle must never be
used as a towing eye.
Attach a tow rope – or better still a tow
rod – to the towing eye.
The towing eye must only be used for
towing and not for recovering a
vehicle.
219
Appearance care
Exterior care
Locks
The locks are lubricated at the factory
using a high quality lock cylinder
grease. Use a de-icing agent only
when absolutely necessary, as this
has a degreasing effect and impairs
lock function. After using a de-icing
agent, have the locks regreased by a
workshop.
Washing
The paintwork of your vehicle is
exposed to environmental influences.
Wash and wax your vehicle regularly.
When using automatic vehicle
washes, select a programme that
includes waxing.
Bird droppings, dead insects, resin,
pollen and the like should be cleaned
off immediately, as they contain
aggressive constituents which can
cause paint damage.
220
Vehicle care
If using a vehicle wash, comply with
the vehicle wash manufacturer's
instructions. The windscreen wiper
and rear window wiper must be
switched off. Remove antenna and
external accessories such as roof
racks etc.
If you wash your vehicle by hand,
make sure that the insides of the
wheel housings are also thoroughly
rinsed out.
Wax painted parts of the vehicle
regularly.
Clean edges and folds on opened
doors and the bonnet as well as the
areas they cover.
Clean bright metal mouldings with a
cleaning solution approved for
aluminium to avoid damages.
Caution
Always use a cleaning agent with
a pH value of four to nine.
Do not use cleaning agents on hot
surfaces.
Do not clean the engine compartment
with a steam-jet or high-pressure jet
cleaner.
Thoroughly rinse and leather-off the
vehicle. Rinse leather frequently. Use
separate leathers for painted and
glass surfaces: remnants of wax on
the windows will impair vision.
Have the door hinges of all doors
greased by a workshop.
Exterior lights
Headlight and other light covers are
made of plastic. Do not use any
abrasive or caustic agents, do not use
an ice scraper, and do not clean them
dry.
Polishing and waxing
Wax the vehicle regularly (at the
latest when water no longer beads).
Otherwise, the paintwork will dry out.
Polishing is necessary only if the paint
has become dull or if solid deposits
have become attached to it.
Paintwork polish with silicone forms a
protective film, making waxing
unnecessary.
Plastic body parts must not be treated
with wax or polishing agents.
Windows and windscreen wiper
blades
Use a soft lint-free cloth or chamois
leather together with window cleaner
and insect remover.
When cleaning the rear window from
inside, always wipe in parallel to the
heating element to prevent damage.
For mechanical removal of ice, use a
sharp-edged ice scraper. Press the
scraper firmly against the glass so
that no dirt can get under it and
scratch the glass.
Clean smearing wiper blades with a
soft cloth and window cleaner.
Remove dirt residues from smearing
wiper blades by using a soft cloth and
window cleaner. Also make sure to
remove any residues such as wax,
insect residues and similar from the
window.
Ice residues, pollution and continuous
wiping on dry windows will damage or
even destroy the wiper blades.
Vehicle care
Glass panel
Never clean with solvents or abrasive
agents, fuels, aggressive media
(e.g. paint cleaner, acetonecontaining solutions etc.), acidic or
highly alkaline media or abrasive
pads.
Wheels and tyres
Do not use high-pressure jet
cleaners.
Clean rims with a pH-neutral wheel
cleaner.
Rims are painted and can be treated
with the same agents as the body.
Paintwork damage
Rectify minor paintwork damage with
a touch-up pen before rust forms.
Have more extensive damage or rust
areas repaired by a workshop.
Underbody
Some areas of the vehicle underbody
have a PVC undercoating while other
critical areas have a durable
protective wax coating.
After the underbody is washed, check
the underbody and have it waxed if
necessary.
Bitumen/rubber materials could
damage the PVC coating. Have
underbody work carried out by a
workshop.
Before and after winter, wash the
underbody and have the protective
wax coating checked.
Liquid gas system
9 Danger
Liquid gas is heavier than air and
can collect in sink points.
Take care when performing work
at the underbody in a pit.
For painting work and when using a
drying booth at a temperature above
60 °C, the liquid gas tank must be
removed.
Do not make any modifications to the
liquid gas system.
221
Towing equipment
Do not clean the coupling ball bar with
a steam-jet or high-pressure jet
cleaner.
Interior care
Interior and upholstery
Only clean the vehicle interior,
including the instrument panel fascia
and panelling, with a dry cloth or
interior cleaner.
Clean the leather upholstery with
clear water and a soft cloth. In case of
heavy soiling, use leather care.
The instrument cluster and the
displays should only be cleaned using
a soft damp cloth. If necessary use a
weak soap solution.
Clean fabric upholstery with a
vacuum cleaner and brush. Remove
stains with an upholstery cleaner.
222
Vehicle care
Clothing fabrics may not be
colourfast. This could cause visible
discolourations, especially on lightcoloured upholstery. Removable
stains and discolourations should be
cleaned as soon as possible.
Clean seat belts with lukewarm water
or interior cleaner.
Caution
Close Velcro fasteners as open
Velcro fasteners on clothing could
damage seat upholstery.
The same applies to clothing with
sharp-edged objects, like zips or
belts or studded jeans.
Plastic and rubber parts
Plastic and rubber parts can be
cleaned with the same cleaner as
used to clean the body. Use interior
cleaner if necessary. Do not use any
other agent. Avoid solvents and petrol
in particular. Do not use highpressure jet cleaners.
Service and maintenance
Service and
maintenance
General information ................... 223
Service information .................. 223
Recommended fluids, lubricants
and parts .................................... 225
Recommended fluids and
lubricants ................................ 225
General information
Service information
In order to ensure economical and
safe vehicle operation and to
maintain the value of your vehicle, it
is of vital importance that all
maintenance work is carried out at the
proper intervals as specified.
The detailed, up-to-date service
schedule for your vehicle is available
at the workshop.
Severe operating conditions exist if
one or more of the following
circumstances occur frequently: Cold
starting, stop and go operation, e.g.
for taxis and police vehicles, trailer
operation, mountain driving, driving
on poor and sandy road surfaces,
increased air pollution, presence of
airborne sand and high dust content,
driving at high altitude and large
variations of temperature.
Under these severe operating
conditions, certain service work may
be required more frequently than the
regular service interval indicated in
223
the service display. Contact a
workshop for customised service
schedules.
Service display 3 88.
Service intervals - country group 1
Maintenance of your vehicle is
required every 16,000 miles or after
one year, whichever occurs first,
unless otherwise indicated in the
service display.
These service intervals are valid for
the following countries:
Andorra, Austria, Belgium, Cyprus,
Denmark, Finland, France, Germany,
Greece, Greenland, Iceland, Ireland,
Italy, Liechtenstein, Luxembourg,
Malta, Monaco, Netherlands,
Norway, Portugal, San Marino, Spain,
Sweden, Switzerland, United
Kingdom.
Service intervals - country group 2
Maintenance of your vehicle
equipped with engine EB2F, EB2DT
or EB2DTS is required every
10,000 miles or after one year,
whichever occurs first, unless
224
Service and maintenance
otherwise indicated in the service
display. Maintenance of your vehicle
with any other engine than mentioned
before is required every
16,000 miles or after one year,
whichever occurs first, unless
otherwise indicated in the service
display.
These service intervals are valid for
the following countries:
Albania, Estonia, Latvia, Lithuania,
Macedonia, Montenegro, Poland,
Serbia, Slovenia.
Service intervals - country group 3
Maintenance of your vehicle
equipped with engine EB2DTS is
required every 6,000 miles or after
one year, whichever occurs first,
unless otherwise indicated in the
service display. Maintenance of your
vehicle equipped with engine EB2F or
EB2DT is required every
10,000 miles or after one year,
whichever occurs first, unless
otherwise indicated in the service
display. Maintenance of your vehicle
with any other engine than mentioned
before is required every
16,000 miles or after one year,
whichever occurs first, unless
otherwise indicated in the service
display.
These service intervals are valid for
the following countries:
Bosnia-Herzegovina, Bulgaria,
Croatia, Czech Republic, Hungary,
Romania, Slovakia.
Service intervals - country group 4
Maintenance of your vehicle is
required every 6,000 miles or after
one year, whichever occurs first,
unless otherwise indicated in the
service display.
These service intervals are valid for
the countries which are not listed in
country group 1, 2 or 3.
Confirmations
Confirmation of service is recorded in
the Service and warranty booklet.
The date and mileage is completed
with the stamp and signature of the
servicing workshop.
Make sure that the Service and
warranty booklet is completed
correctly as continuous proof of
service is essential if any warranty or
goodwill claims are to be met, and is
also a benefit when selling the
vehicle.
Service and maintenance
Recommended fluids,
lubricants and parts
Recommended fluids and
lubricants
Only use products that meet the
recommended specifications.
9 Warning
Operating materials are
hazardous and could be
poisonous. Handle with care. Pay
attention to information given on
the containers.
Engine oil
Engine oil is identified by its quality
and its viscosity. Quality is more
important than viscosity when
selecting which engine oil to use. The
oil quality ensures e.g. engine
cleanliness, wear protection and oil
aging control, whereas viscosity
grade gives information on the oil's
thickness over a temperature range.
225
Dexos is the newest engine oil quality
that provides optimum protection for
gasoline and diesel engines. If it is
unavailable, engine oils of other listed
qualities have to be used.
Recommendations for gasoline
engines are also valid for
Compressed Natural Gas (CNG),
Liquified Petroleum Gas (LPG) and
Ethanol (E85) fuelled engines.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 229.
Use of engine oils for all petrol
engines with only ACEA quality is
prohibited, since it can cause engine
damage under certain operating
conditions.
Select the appropriate engine oil
based on its quality and on the
minimum ambient temperature
3 229.
Topping up engine oil
Engine oil viscosity grades
The SAE viscosity grade gives
information of the thickness of the oil.
Multigrade oil is indicated by two
figures, e.g. SAE 5W-30. The first
figure, followed by a W, indicates the
low temperature viscosity and the
second figure the high temperature
viscosity.
Select the appropriate viscosity grade
depending on the minimum ambient
temperature 3 229.
Caution
In case of any spilled oil, wipe it up
and dispose it properly.
Engine oils of different manufacturers
and brands can be mixed as long as
they comply with the required engine
oil quality and viscosity.
Additional engine oil additives
The use of additional engine oil
additives could cause damage and
invalidate the warranty.
226
Service and maintenance
All of the recommended viscosity
grades are suitable for high ambient
temperatures.
Coolant and antifreeze
Use only organic acid type-long life
coolant (LLC) antifreeze approved for
the vehicle. Consult a workshop.
The system is factory filled with
coolant designed for excellent
corrosion protection and frost
protection down to approx. -37 °C.
This concentration should be
maintained all year round. The use of
additional coolant additives that
intend to give additional corrosion
protection or seal against minor leaks
can cause function problems. Liability
for consequences resulting from the
use of additional coolant additives will
be rejected.
Washer fluid
Use only washer fluid approved for
the vehicle to prevent damage of
wiper blades, paintwork, plastic and
rubber parts. Consult a workshop.
Brake and clutch fluid
Over time, brake fluid absorbs
moisture which will reduce braking
effectiveness. The brake fluid should
therefore be replaced at the specified
interval.
Technical data
Technical data
Vehicle identification .................. 227
Vehicle Identification Number .. 227
Identification plate ................... 227
Engine identification ................ 228
Vehicle data ............................... 229
Recommended fluids and
lubricants ................................ 229
Engine data ............................. 232
Performance ............................ 234
Vehicle weight ......................... 235
Vehicle dimensions ................. 236
Capacities ................................ 237
Tyre pressures ........................ 238
Vehicle identification
227
Identification plate
Vehicle Identification
Number
The identification plate is located on
the front left or right door frame.
The Vehicle Identification Number
may be stamped on the identification
plate and on the floor pan, under the
floor covering, visible under a cover.
The Vehicle Identification Number
may be embossed on the instrument
panel, visible through the windscreen,
or in the engine compartment on the
right body panel.
228
Technical data
Information on identification label:
1 : manufacturer
2 : type approval number
3 : vehicle identification number
4 : permissible gross vehicle weight
rating in kg
5 : permissible gross train weight
in kg
6 : maximum permissible front axle
load in kg
7 : maximum permissible rear axle
load in kg
8 : vehicle-specific or countryspecific data
The combined total of front and rear
axle loads must not exceed the
permissible gross vehicle weight. For
example, if the front axle is bearing its
maximum permissible load, the rear
axle can only bear a load that is equal
to the gross vehicle weight minus the
front axle load.
The technical data is determined in
accordance with European
Community standards. We reserve
the right to make modifications.
Specifications in the vehicle
documents always have priority over
those given in this manual.
Engine identification
The technical data tables show the
engine identifier code. Engine data
3 232.
To identify the respective engine,
refer to the engine power in the EEC
Certificate of Conformity provided
with your vehicle or other national
registration documents.
Technical data
229
Vehicle data
Recommended fluids and lubricants
European service schedule
Required engine oil quality
Countries with European service interval (country groups 1,2,3) 3 223
Engine oil quality
Petrol engines
(including CNG, LPG, E85)
Diesel engines
dexos1 Gen2
✔
–
dexos2
–
✔
Diesel engines only: In case dexos quality is unavailable, you may use max. one litre engine oil quality ACEA C3 once
between each oil change.
Engine oil viscosity grades
Countries with European service interval (country groups 1,2,3) 3 223
Ambient temperature
Petrol and diesel engines
down to -25 °C
SAE 0W-30 or SAE 0W-40
SAE 5W-30 or SAE 5W-40
below -25 °C
SAE 0W-30 or SAE 0W-40
230
Technical data
International service schedule
Required engine oil quality
Countries with international service interval (country group 4) 3 223
Engine oil quality
Petrol engines
(including CNG, LPG, E85)
Diesel engines
dexos1 Gen2
✔
–
dexos2
–
✔
In case dexos quality is unavailable you may use the oil qualities listed below:
Countries with international service interval (country group 4) 3 223
Engine oil quality
Petrol engines
(including CNG, LPG, E85)
Diesel engines
ACEA A3/B4
–
✔
ACEA C3
–
✔
Engine oil viscosity grades
Countries with international service interval (country group 4) 3 223
Ambient temperature
Petrol and diesel engines
down to -25 °C
SAE 0W-30 or SAE 0W-40
SAE 5W-30 or SAE 5W-40
Technical data
Countries with international service interval (country group 4) 3 223
below -25 °C
SAE 0W-30 or SAE 0W-40
down to -20 °C
SAE 10W-301) or SAE 10W-40 1)
1)
Permitted, but usage of oils with dexos quality is recommended.
231
232
Technical data
Engine data
Engine identifier code
B12xE
B12xE
B12xHT
B12xHT
Sales designation
1.2
1.2 LPG
1.2 Turbo
1.2 Turbo
Engineering code
EB2F
EB2F
EB2DT
EB2DTS
Piston displacement [cm3]
1199
1199
1199
1199
Engine power [kW]
60
55
81
96
at rpm
5750
5600
5500
5500
Torque [Nm]
118
115
205
230
at rpm
2750
2800
1500
1750
Petrol
Liquid gas/Petrol
Petrol
Petrol
recommended
95
95
95
95
possible
98
98
98
98
Additional fuel type
–
Liquid gas (LPG)
–
–
Fuel type
Octane rating
2)
RON2)
A country-specific label at the fuel filler flap can supersede the engine-specific requirement.
Technical data
Engine identifier code
B16DT
B16DTH
B16DTH
Sales designation
1.6
1.6
1.6
Engineering code
DV6FD
DV6FC
DV6FC
Piston displacement [cm3]
1560
1560
1560
Engine power [kW]
73
85
88
at rpm
3750
3500
3500
Torque [Nm]
254
300
300
at rpm
1750
1750
1750
Fuel type
Diesel
Diesel
Diesel
Additional fuel type
–
–
–
233
234
Technical data
Performance
B12xE
B12xE
LPG
B12xHT
B12xHT
Manual transmission
106
106
1173)
1284)
Automatic transmission
–
–
116
–
Engine
Maximum speed [mph]
3)
4)
5-gear transmission
6-gear transmission
Engine
B16DT
B16DTH
Manual transmission
112
116
Automatic transmission
–
–
Maximum speed [mph]
Technical data
Vehicle weight
Kerb weight, basic model without any optional equipment
without/with
air conditioning
[kg]
5)
6)
Engine
Manual
transmission
Automatic
transmission
B12xE
1163/1174
–
B12xE
LPG
1159/1170
–
B12xHT
1234/12455)
1278/1289
B12xHT
1263/12746)
–
B16DT
1278/1289
–
B16DTH
1306/1319
–
5-gear transmission
6-gear transmission
Optional equipment and accessories increase the kerb weight.
Loading information 3 71.
235
236
Technical data
Vehicle dimensions
Crossland X
Length [mm]
4212
Width without exterior mirrors [mm]
1765
Width with two exterior mirrors [mm]
1976
Width with two exterior mirrors folded [mm]
1825
Height (without antenna) [mm]
1597
Length of load compartment floor [mm]
793
Length of load compartment with folded rear seats [mm]
1483
Load compartment width [mm]
947
Load compartment height with cover [mm]
584
Load compartment height without cover [mm]
894
Height of load compartment opening [mm]
712
Wheelbase [mm]
2604
Turning circle diameter [m]
11.2
Technical data
237
Capacities
Engine oil
Engine
B12xE,
B12xE
LPG
B12xHT
B16DT
B16DTH
including Filter [l]
3.25
3.5
3.75
3.75
between MIN and MAX [l]
1.0
1.0
1.0
1.5
Fuel tank
Petrol/diesel, refilling quantity [l]
45
Liquid gas LPG, refilling quantity [l]
36
AdBlue tank
AdBlue, refilling quantity [l]
14.8
238
Technical data
Tyre pressures
Engine
Tyres
Comfort with up to 3 people
ECO with up to 3 people
With full load
front
rear
front
rear
front
rear
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
B12xE,
B12xE
LPG,
B12xHT
195/65 R15 91T,
195/60 R16 89H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 290/2.9 (42)
215/50 R17 91H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
205/60 R16 92H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
B12xHT7)
195/60 R16 89H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 290/2.9 (42)
215/50 R17 91H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
205/60 R16 92H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
195/65 R15 91T,
195/60 R16 89H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 290/2.9 (42)
215/50 R17 91H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
205/60 R16 92H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
B16DT
Technical data
239
Comfort with up to 3 people
ECO with up to 3 people
With full load
front
rear
front
rear
front
rear
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
[kPa/bar]
([psi])
B16DTH 195/60 R16 89H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 290/2.9 (42)
215/50 R17 91H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
205/60 R16 92H
230/2.3 (33)
230/2.3 (33)
250/2.5 (36)
250/2.5 (36)
240/2.4 (35) 270/2.7 (39)
Temporary spare
wheel
125/85 R16
420/4.2 (60)
420/4.2 (60)
–
–
420/4.2 (60) 420/4.2 (60)
Engine
All
7)
Tyres
6-gear manual transmission / 96kW
240
Customer information
Customer
information
Customer information
Declaration of conformity
Tansmission systems
Customer information ................ 240
Declaration of conformity ......... 240
REACH .................................... 243
Collision damage repair ........... 243
Software acknowledgement .... 243
Software update ...................... 245
Registered trademarks ............ 246
Vehicle data recording and pri‐
vacy ........................................... 246
Event data recorders ............... 246
Radio Frequency Identification
(RFID) ..................................... 247
This vehicle has systems that
transmit and / or receive radio waves
subject to Directive 1999/5/EC or
2014/53/EU. The manufacturers of
the systems listed below declare
conformity withDirective 1999/5/EC
or 2014/53/EU. The full text of the EU
declaration of conformity for each
system is available at the following
internet address: www.opel.com/
conformity
Importer is
Opel / Vauxhall, Bahnhofsplatz,
65423 Ruesselsheim am Main,
Germany.
Navi 5.0 IntelliLink
Continental
LCIE Bureau Veritas-Site de
Fontenay aux Roses, 33 avenue du
général Leclerc, 92260 Fontenay aux
Roses, France
Operation
Maximum output
frequency (MHz) (dBm)
2400.0 - 2483.5
2.2
2400.0 - 2483.5
15
Infotainment system R 4.0 IntelliLink
LGE
LG Electronics European Shared
Service Center B.V.
Krijgsman 1, 1186 DM Amstelveen,
The Netherlands
Operation
Maximum output
frequency (MHz) (dBm)
2400.0 - 2483.5
4
2400.0 - 2483.5
13
5725.0 - 5850.0
13
Infotainment system R 4.0
Clarion
244 rue du Pré à Varois, 54670
Custines, France
Operation frequency:
2400 - 2480 MHz
Maximum output: 4 dBm
Customer information
OnStar module
LGE
LG Electronics European Shared
Service Center B.V.
Krijgsman 1, 1186 DM Amstelveen,
The Netherlands
Operation
Maximum output
frequency (MHz) (dBm)
2402 - 2480
4
2412 - 2462
18
880 - 915
33
1710 - 1785
24
1850 - 1910
24
1920 - 1980
24
2500 - 2570
23
Antenna module
Laird
Daimlerring 31, 31135 Hildesheim,
Germany
Operation frequency: N/A
Maximum output: N/A
ASK Automotive Pvt. Ltd.
Unit 2 Plot No. 30-31, FathepurNawada, Manesar, Gurugram,
Haryana 122050, India
Operation frequency: N/A
Maximum output: N/A
Radio remote control transmitter
Hülsbeck & Fürst GmbH & Co. KG
Steeger Str. 17, 42551 Velbert,
Germany
Operation frequency: 433.92 MHz
Maximum output: 10 dBm
Radio remote control receiver
Delphi European, Middle Eastern &
African Regional Offices Customer
Technology
Center Avenue de Luxembourg,
L-4940 Bascharage, G.D. of
Luxembourg
Operation frequency:
119.0 - 128.6 kHz
Maximum output: 16dBµA/m @ 10m
Electronic key transmitter
Valeo
43 Rue Bayen, 75017 Paris, France
241
Operation frequency: 433.92 MHz
Maximum output: 10 dBm
Immobiliser
KOSTAL of America, Inc.
350 Stephenson Hwy, Troy MI 48083,
USA
Operation frequency: 125 kHz
Maximum output: 5 dBμA/m at 10m
242
Jack
Customer information
Customer information
Translation of the original declaration
of conformity
Declaration of conformity according
to EC Directive 2006/42/EC
We declare that the product:
Product designation: Jack
Type/GM part number: 3637376
Type/PSA part number: 9649243380
is in compliance with the provisions of
Directive 2006/42/EC.
Applied technical standards:
GMN9737
: jacking
GM 14337
: standard equipment
jack – hardware
tests
GMW15005 : standard equipment
jack and spare tyre,
vehicle test
ISO TS 16949 : quality
management
systems
The signatory is authorised to
compile the technical documentation.
Rüsselsheim, 13th December 2016
signed by
André-Alexander Konter
Engineering Group Manager Tyre
and Wheel Systems
Adam Opel AG
D-65423 Rüsselsheim
REACH
Registration, Evaluation,
Authorisation and Restriction of
Chemicals (REACH) is a European
Union regulation adopted to improve
the protection of human health and
the environment from the risks that
can be posed by chemicals. Visit
www.opel.com/reach for further
information and for access to the
Article 33 communication.
243
Collision damage repair
Paint thickness
Due to production techniques, the
thickness of the paint can vary
between 50 and 400 µm.
Therefore, different paint thickness is
no indicator for a collision damage
repair.
Software acknowledgement
Certain OnStar components include
libcurl and unzip software and other
third party software. Below are the
notices and licenses associated with
libcurl and unzip and for other third
party software please see http://
www.lg.com/global/support/
opensource/index.
libcurl
Copyright and permission notice
Copyright (c) 1996 - 2010, Daniel
Stenberg, <[email protected]>.
All rights reserved.
244
Customer information
Permission to use, copy, modify, and
distribute this software for any
purpose with or without fee is hereby
granted, provided that the above
copyright notice and this permission
notice appear in all copies.
The software is provided "as is",
without warranty of any kind, express
or implied, including but not limited to
the warranties of merchantability,
fitness for a particular purpose and
noninfringement of third party rights.
In no event shall the authors or
copyright holders be liable for any
claim, damages or other liability,
whether in an action of contract, tort
or otherwise, arising from, out of or in
connection with the software or the
use or other dealings in the software.
Except as contained in this notice, the
name of a copyright holder shall not
be used in advertising or otherwise to
promote the sale, use or other
dealings in this Software without prior
written authorization of the copyright
holder.
unzip
This is version 2005-Feb-10 of the
Info-ZIP copyright and license. The
definitive version of this document
should be available at ftp://ftp.infozip.org/pub/infozip/license.html
indefinitely.
Copyright (c) 1990-2005 Info-ZIP. All
rights reserved.
For the purposes of this copyright and
license, “Info-ZIP” is defined as the
following set of individuals:
Mark Adler, John Bush, Karl Davis,
Harald Denker, Jean-Michel Dubois,
Jean-loup Gailly, Hunter Goatley, Ed
Gordon, Ian Gorman, Chris Herborth,
Dirk Haase, Greg Hartwig, Robert
Heath, Jonathan Hudson, Paul
Kienitz, David Kirschbaum, Johnny
Lee, Onno van der Linden, Igor
Mandrichenko, Steve P. Miller, Sergio
Monesi, Keith Owens, George
Petrov, Greg Roelofs, Kai Uwe
Rommel, Steve Salisbury, Dave
Smith, Steven M. Schweda, Christian
Spieler, Cosmin Truta, Antoine
Verheijen, Paul von Behren, Rich
Wales, Mike White.
This software is provided “as is,”
without warranty of any kind, express
or implied. In no event shall Info-ZIP
or its contributors be held liable for
any direct, indirect, incidental, special
or consequential damages arising out
of the use of or inability to use this
software.
Permission is granted to anyone to
use this software for any purpose,
including commercial applications,
and to alter it and redistribute it freely,
subject to the following restrictions:
1. Redistributions of source code
must retain the above copyright
notice, definition, disclaimer, and
this list of conditions.
2. Redistributions in binary form
(compiled executables) must
reproduce the above copyright
notice, definition, disclaimer, and
this list of conditions in
documentation and/or other
materials provided with the
distribution. The sole exception to
this condition is redistribution of a
standard UnZipSFX binary
(including SFXWiz) as part of a
self-extracting archive; that is
Customer information
permitted without inclusion of this
license, as long as the normal
SFX banner has not been
removed from the binary or
disabled.
3. Altered versions--including, but
not limited to, ports to new
operating systems, existing ports
with new graphical interfaces, and
dynamic, shared, or static library
versions--must be plainly marked
as such and must not be
misrepresented as being the
original source. Such altered
versions also must not be
misrepresented as being Info-ZIP
releases--including, but not
limited to, labeling of the altered
versions with the names “InfoZIP” (or any variation thereof,
including, but not limited to,
different capitalizations), “Pocket
UnZip,” “WiZ” or “MacZip” without
the explicit permission of Info-ZIP.
Such altered versions are further
prohibited from misrepresentative
use of the Zip-Bugs or Info-ZIP email addresses or of the Info-ZIP
URL(s).
4. Info-ZIP retains the right to use
the names “Info-ZIP,” “Zip,”
“UnZip,” “UnZipSFX,” “WiZ,”
“Pocket UnZip,” “Pocket Zip,” and
“MacZip” for its own source and
binary releases.
Software update
The Infotainment system can
download and install selected
software updates over a wireless
connection.
Notice
The availability of these over-the-air
vehicle software updates varies by
vehicle and country. Find more
information on our home page.
Internet connection
Downloading over-the-air vehicle
software updates requires internet
connectivity, which can be accessed
through the vehicle's built-in OnStar
245
connection or another passwordprotected Wi-Fi hotspot, e.g. provided
by a mobile phone.
To connect the Infotainment system
to a hotspot, select Settings on the
home screen, Wi-Fi and then Manage
Wi-Fi Networks. Select the desired
Wi-Fi network, and follow the onscreen prompts.
Updates
The system will prompt for certain
updates to be downloaded and
installed. There is also an option to
check for updates manually.
To manually check for updates, select
Settings on the home screen,
Software Information and then
System Update. Follow the on-screen
prompts.
Notice
Steps for downloading and installing
updates may vary by vehicle.
Notice
During the installation process, the
vehicle may not be operational.
246
Customer information
Registered trademarks
Apple Inc.
Apple CarPlay™ is a trademark of
Apple Inc.
App Store® and iTunes Store® are
registered trademarks of Apple Inc.
iPhone®, iPod®, iPod touch®, iPod
nano®, iPad® and Siri® are registered
trademarks of Apple Inc.
Bluetooth SIG, Inc.
Bluetooth® is a registered trademark
of Bluetooth SIG, Inc.
DivX, LLC
DivX® and DivX Certified® are
registered trademarks of DivX, LLC.
EnGIS Technologies, Inc.
BringGo® is a registered trademark of
EnGIS Technologies, Inc.
Google Inc.
Android™ and Google Play™ Store
are trademarks of Google Inc.
Stitcher Inc.
Stitcher™ is a trademark of Stitcher,
Inc.
Verband der Automobilindustrie e.V.
AdBlue® is a registered trademark of
the VDA.
Vehicle data recording
and privacy
Event data recorders
Data storage modules in the
vehicle
A large number of electronic
components of your vehicle contain
data storage modules temporarily or
permanently storing technical data
about the condition of the vehicle,
events and errors. In general, this
technical information documents the
condition of parts, modules, systems
or the environment:
● operating conditions of system
components (e.g. filling levels)
● status messages of the vehicle
and its single components (e.g.
number of wheel revolutions /
rotational speed, deceleration,
lateral acceleration)
● dysfunctions and defects in
important system components
Customer information
●
vehicle reactions in particular
driving situations (e.g. inflation of
an airbag, activation of the
stability regulation system)
● environmental conditions (e.g.
temperature)
These data are exclusively technical
and help identifying and correcting
errors as well as optimising vehicle
functions.
Motion profiles indicating travelled
routes cannot be created with these
data.
If services are used (e.g. repair
works, service processes, warranty
cases, quality assurance),
employees of the service network
(manufacturer included) are able to
read out this technical information
from the event and error data storage
modules applying special diagnostic
devices. If required, you will receive
further information at these
workshops. After an error has been
corrected, the data are deleted from
the error storage module or they are
constantly overwritten.
When using the vehicle, situations
may occur in which these technical
data related to other information
(accident report, damages on the
vehicle, witness statements etc.) may
be associated with a specific person possibly, with the assistance of an
expert.
Additional functions contractually
agreed upon with the client (e.g.
vehicle location in emergency cases)
allow the transmission of particular
vehicle data from the vehicle.
Radio Frequency
Identification (RFID)
RFID technology is used in some
vehicles for functions such as tyre
pressure monitoring and ignition
system security. It is also used in
connection with conveniences such
as radio remote controls for door
locking/unlocking and starting, and invehicle transmitters for garage door
openers. RFID technology in
Vauxhall vehicles does not use or
record personal information or link
with any other Vauxhall system
containing personal information.
247
248
Index
A
Accessories and vehicle
modifications .......................... 184
Active emergency braking.......... 156
Adaptive forward lighting ........... 112
AdBlue.................................. 93, 141
Adjustable air vents ................... 128
Advanced parking assist............ 163
Airbag and belt tensioners ........... 90
Airbag deactivation ................ 56, 90
Airbag label................................... 51
Airbag system .............................. 51
Air conditioning regular
operation ................................ 130
Air conditioning system .............. 120
Air intake .................................... 129
Air vents...................................... 128
Antilock brake system ................ 148
Antilock brake system (ABS) ....... 91
Anti-theft alarm system ................ 32
Anti-theft locking system .............. 31
Appearance care........................ 219
Armrest................................... 46, 47
Ashtrays ....................................... 80
Automatic anti-dazzle .................. 36
Automatic light control ............... 111
Automatic locking ........................ 28
Automatic transmission ............. 144
Autostop............................... 94, 137
Auxiliary heater........................... 127
B
Battery discharge protection ...... 118
Battery voltage ........................... 101
Belts.............................................. 48
BlueInjection............................... 141
Bonnet ....................................... 186
Brake and clutch fluid................. 225
Brake and clutch system ............. 91
Brake assist ............................... 149
Brake fluid .................................. 189
Brakes ............................... 148, 189
Breakdown.................................. 217
Bulb replacement ....................... 191
C
Capacities .................................. 237
Catalytic converter ..................... 140
Central locking system ................ 24
Centre console lighting .............. 117
Centre console storage ............... 65
Changing tyre and wheel size . . . 208
Charging system .......................... 90
Child locks ................................... 29
Child restraint installation
locations ................................... 60
Child restraints.............................. 57
Child restraint systems ................ 57
Cigarette lighter ........................... 80
Climate control ............................. 15
Climate control systems............. 119
249
Clock............................................. 78
Collision damage repair.............. 243
Control indicators.......................... 89
Control of the vehicle ................. 132
Controls........................................ 74
Convex shape .............................. 34
Coolant and antifreeze............... 225
Cruise control ...................... 94, 151
Cupholders .................................. 64
Curtain airbag system .................. 55
D
Danger, Warnings and Cautions . . . 4
Daytime running lights ............... 112
Declaration of conformity............ 240
DEF............................................ 141
Deflation detection system........... 93
Diesel exhaust fluid.................... 141
Diesel fuel system bleeding ....... 190
Diesel particle filter............... 93, 140
Door open .................................... 95
Doors............................................ 30
Driver alert.................................. 175
Driver assistance systems.......... 151
Driver Information Centre............. 95
Driving characteristics and
towing tips .............................. 180
Driving hints................................ 132
E
Electric adjustment ...................... 34
Electrical system......................... 199
Electronic climate control system 123
Electronic driving programmes . . 145
Electronic key system................... 23
Electronic Stability Control and
Traction Control system.... 92, 149
Electronic Stability Control and
Traction Control system off....... 92
End-of-life vehicle recovery ....... 185
Engine compartment fuse box ... 200
Engine coolant ........................... 188
Engine coolant temperature ........ 92
Engine coolant temperature
gauge ....................................... 87
Engine data ............................... 232
Engine exhaust .......................... 140
Engine identification................... 228
Engine oil ................... 187, 225, 229
Engine oil level monitor................ 88
Engine oil pressure ...................... 93
Entry lighting .............................. 117
Event data recorders.................. 246
Exit lighting ................................ 117
Exterior care .............................. 219
Exterior light ................................. 94
Exterior lighting .................... 12, 110
Exterior mirrors............................. 34
F
Fault ........................................... 146
First aid......................................... 70
First aid kit ................................... 70
Fixed air vents ........................... 129
Fog light ....................................... 94
Fog lights ................................... 194
Folding mirrors ............................. 35
Forward collision alert................. 155
Front airbag system ..................... 54
Front fog lights ........................... 114
Front pedestrian protection........ 158
Front seats.................................... 43
Fuel............................................. 176
Fuel for diesel engines .............. 177
Fuel for liquid gas operation....... 177
Fuel for petrol engines ............... 176
Fuel gauge ................................... 86
Fuel selector ................................ 86
Fuses ......................................... 199
G
Gauges......................................... 84
Gear shifting................................. 92
General information ................... 180
Glass panel .................................. 40
Glovebox ..................................... 64
H
Halogen headlights .................... 191
Hand brake................................. 148
250
Hazard warning flashers ............ 113
Headlight flash ........................... 111
Headlight range adjustment ...... 112
Headlights................................... 110
Head restraint adjustment ............. 8
Head restraints ............................ 42
Head-up display............................ 99
Heated mirrors ............................. 35
Heated rear window ..................... 38
Heated steering wheel ................. 74
Heated windscreen....................... 39
Heating ........................................ 46
Heating and ventilation system . 119
High beam ........................... 94, 111
High beam assist.......................... 94
Hill start assist ........................... 149
Horn ....................................... 13, 75
I
Identification plate ..................... 227
Ignition switch positions ............. 132
Immobiliser .................................. 34
Indicators...................................... 84
Inductive charging........................ 79
Info display................................... 97
Instrument cluster ........................ 81
Instrument panel fuse box ......... 201
Instrument panel illumination ..... 199
Instrument panel illumination
control .................................... 116
Instrument panel overview ........... 10
Interior care ............................... 221
Interior lighting............................ 116
Interior lights ...................... 116, 199
Interior mirrors.............................. 36
Interruption of power supply ...... 146
Introduction .................................... 3
J
Jump starting ............................. 216
K
Keys ............................................. 21
Keys, locks................................... 21
L
Lane departure warning....... 92, 173
Lashing eyes ............................... 69
LED headlights........................... 194
Lighting features......................... 117
Light switch ................................ 110
Load compartment ................ 30, 65
Load compartment cover ............. 68
Loading information ..................... 71
Low beam..................................... 94
Low fuel ....................................... 94
LPG...................................... 86, 177
M
Malfunction indicator light ............ 90
Manual anti-dazzle ...................... 36
Manual mode ............................. 145
Manual transmission .................. 147
Mirror adjustment ........................... 9
Misted light covers ..................... 115
N
New vehicle running-in .............. 132
Number plate light ..................... 199
O
Object detection systems........... 160
Odometer ..................................... 85
Oil, engine.......................... 225, 229
OnStar........................................ 105
Outside temperature .................... 77
Overrun cut-off ........................... 136
P
Panoramic view system.............. 169
Parking ................................ 19, 139
Parking assist ............................ 160
Parking brake ............................ 148
Parking lights ............................. 115
Particulate filter........................... 140
Performance .............................. 234
Performing work ........................ 186
Power button.............................. 133
Power outlets ............................... 78
Power saving mode.................... 134
Power windows ............................ 37
251
Preheating ................................... 93
Puncture..................................... 212
Q
Quickheat................................... 127
R
Radio Frequency Identification
(RFID)..................................... 247
Radio remote control ................... 22
Rain sensor.................................. 94
REACH....................................... 243
Reading lights ............................ 116
Rear floor storage cover .............. 68
Rear fog light ....................... 94, 115
Rear seats.................................... 47
Rear view camera ...................... 172
Rear window wiper/washer .......... 77
Recommended fluids and
lubricants ........................ 225, 229
Refuelling ................................... 178
Registered trademarks............... 246
Reversing lights ......................... 115
Ride control systems.................. 149
Roof.............................................. 40
Roof load...................................... 71
Roof rack ..................................... 71
S
Safety belts................................... 48
Seat adjustment ....................... 7, 44
Seat belt ........................................ 8
Seat belt reminder ....................... 89
Seat belts ..................................... 48
Seat heating................................. 46
Seat position ................................ 43
Selective catalytic reduction....... 141
Selector lever ............................. 144
Service ............................... 130, 223
Service display ............................ 88
Service information .................... 223
Service vehicle soon .................... 91
Side airbag system ...................... 54
Side blind spot alert.................... 168
Sidelights.................................... 110
Side turn signal lights ................ 198
Software acknowledgement....... 243
Software update......................... 245
Spare wheel ............................... 214
Speed limiter......................... 95, 153
Speedometer ............................... 84
Starting and operating................ 132
Starting off ................................... 17
Starting the engine .................... 135
Steering...................................... 132
Steering wheel adjustment ...... 9, 74
Steering wheel controls ............... 74
Stop engine.................................. 91
Stop-start system........................ 137
Storage......................................... 64
Storage compartments................. 64
Sunvisor lights ........................... 117
Sun visors .................................... 40
Symbols ......................................... 4
System check............................... 91
T
Tachometer ................................. 85
Tail lights ................................... 194
Three-point seat belt .................... 49
Tools .......................................... 204
Tow bar....................................... 180
Towing................................ 180, 217
Towing another vehicle ............. 218
Towing equipment ..................... 181
Towing the vehicle ..................... 217
Traffic sign assistant..................... 95
Trailer coupling........................... 180
Trailer towing ............................. 180
Transmission ............................... 16
Transmission display ................. 144
Tread depth ............................... 207
Trip odometer .............................. 85
Turn and lane-change signals ... 114
Turn signal ................................... 89
Tyre chains ................................ 208
Tyre deflation detection system . 206
Tyre designations ...................... 205
Tyre pressure ............................ 205
Tyre pressures ........................... 238
Tyre repair kit ............................. 209
252
U
Ultrasonic parking assist............. 160
Upholstery.................................. 221
Using this manual .......................... 3
V
Valet mode................................... 97
Vehicle battery ........................... 189
Vehicle checks............................ 186
Vehicle data................................ 229
Vehicle data recording and
privacy..................................... 246
Vehicle dimensions .................... 236
Vehicle Identification Number .... 227
Vehicle jack................................ 204
Vehicle messages ..................... 101
Vehicle personalisation ............. 102
Vehicle security............................ 31
Vehicle specific data ...................... 3
Vehicle storage........................... 185
Vehicle tools............................... 204
Vehicle unlocking ........................... 6
Vehicle weight ........................... 235
Ventilation................................... 119
W
Warning chimes ......................... 101
Warning lights............................... 84
Warning triangle .......................... 70
Washer and wiper systems ......... 13
Washer fluid ............................... 188
Wheel changing ......................... 212
Wheel covers ............................. 208
Wheels and tyres ....................... 204
Windows....................................... 36
Windscreen................................... 36
Windscreen wiper/washer ........... 75
Winter tyres ............................... 204
Wiper blade replacement .......... 191
Copyright by General Motors UK Ltd.
The information contained in this publication is effective as of the date indicated below. General Motors UK Ltd. reserves the right to make changes to the technical specifications,
features and design of the vehicles relative to the information contained in this publication, as well as changes to the publication itself.
Edition: August 2017, General Motors UK Ltd.
Printed on chlorine-free bleached paper.
ID-VCDAORIE1708-en
*ID-VCDAORIE1708-EN*
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement