542001 PRO 81 PRTS.cdr
Parts list for the PRO 81 4-gallon
Backpack Sprayer
PARTS LIST
635
Kit
Kit
Kit
Kit
Kit
Kit
Kit
Kit
636
573 633
636
639
636
10
2CH 636
2A 636
635
639
Kit 13
1AS
638
Kit 14
Kit 17
Kit 18F
13 12
637
13 12
13 12
181
637
13
633
635 634 633
Kit
Kit
Kit
Kit
Kit
Kit
13
12
635
634
17 18F
13 14
13 14
13 14
17
637
11P
13
637 181
13
14
638
8
7
7
532
638
532
638
638
7 180
180 7
638
18F
18F
18F
GRIP 18F
367
21
20
18F
FILT 18F
19 18F
20
20
GREASE
367
21
19
19
19
21
18F
18F
18F
18F
20
21
18F
18F
22
18F
25
24
26 25
Kit 367
Kit 392
Kit 532
Kit
Kit
Kit
Kit
573
633
634
635
Kit
Kit
Kit
Kit
636
637
638
639
Kit FILT
Kit GRIP
+ Kit GREASE
18F 392
392 25
Kit 26
Kit 180
638
7
181 7
19
20
21
22
24
25
Kit 181
14
638
17
1AS
2A
2CH
7
8
10
11P
12
24 25
25
6” strainer for tank lid
Seal for 6” lid
Check valve for lid
Pump handle (fold back type)
Clips for pump handle
O-ring for pressure tank
Plastic retention clamp
O-ring and washer set for
diaphragm (kit 13)
Diaphragm pump module
(complete)
Crank with plastic pin
Hose set
Complete spray gun with built-in
filter & grip
Spindle set
Spindle, O-ring, & washer set
Plug set (cap, spring & o-ring)
20” brass spray wand
Nozzle holder
Adjustable brass nozzle with
holder
O-ring for spray tip
Small locking R-pin for pump
handle
Large locking R-pin for pump
handle
O-rings (2) for gun grip
Washer set for spray guns
Screws & lock nut set for pump
lever for professional line
Special buckle attachment
Shoulder strap clip
Shoulder strap clips
Padded adjustable shoulder
straps (2) w/hooks
Blue tank lid & seal
Nylon bearing and washer
Ambidextrous pump lever assy
Solvent resistant pressure
chamber
Filter replacement for Kit 18F
Grip replacement for Kit 18F
Silicone grease lubricant for all
sprayers.
NOTE:
+ Not supplied with unit, see sheet of accessories.
NOTE:
For best results, the sprayer shoulde be pumped
every 5 seconds on a continuous basis. This will
maintain your spraying pressure. If you do not pump,
you will not have pressure to spray.
ATTENTION
FOR BEST PERFORMANCE, PERIODICALLY
GREASE PUMPING MECHANISM, ALL
O-RINGS,& SEALS
b
The PRO 81 Backpack Sprayer
We would like to congratulate you on the purchase of your new PRO 81, the sprayer that allows you the easiest,
most comfortable way of carrying out your farm and garden projects with the revolutionary diaphragm pump
(Patented), that eleminates the problems inherent in most sprayers.
We strongly recommend you to carefully read and follow all the information on this sheet, the Warnings Sheet and the Trouble
Shooting Guide (if needed). Also follow all instructions in MSDS (Material Safety Data Sheet) provided by the manufacturer
of the chemical product used.
HOW TO ASSEMBLE
1.
2.
Attach spray wand to spray gun and tighten firmly.
Take pump handle Kit 7 and insert into the tube of the pump lever Kit 638 the pump lever is ambidextrous
so the handle can be inserted on the right or left side as you wish. You will
notice holes drilled through both the pump handle and the pump lever. Align these holes, take the “R” pin
provided and place through the holes. This affixes the handle in place and is ready for use.
For storage reverse process and then place “R” pin through the pump lever Kit 638 to keep from losing “R” pin.
HOW TO PREPARE YOUR UNIT FOR USE
1.
2.
3.
4.
5.
6.
Remove cap.
Mix solutions in a separate receptacle, following manufacturers directions on the container.
Pour pre-mixed solutions through the strainer into sprayer and cap.
Place sprayer on back and pressurize tank by pumping approximately 10 to 15 times. For best results, the
sprayer should be pumped every 5 seconds on a continuous basis. This will maintain your spraying
pressure. If you do not pump, you will not have pressure to spray.
Always oil the seal on cap of unit as well as the check valve, this will extend life of seal and it is important for
obtaining proper seal with no leaks.
A unit that has been used with herbicides should never be used to spray insecticides, unless the sprayer has
been properly cleaned and all other chemicals neutralized. Failure to do this could cause you to kill plants that
have been sprayed. Consult with the manufacturer of the chemicals in use to obtain proper instructions.
HOW TO CLEAN AND MAINTAIN
1.
2.
3.
Remove cap and pour out remaining solution, then rinse all parts thoroughly with clean water.
Leaving approximately ½ gallon of fresh water in tank, pressurize and flush pumping systems by depressing
trigger at least 2 minutes, then drain all remaining water.
Always store tank clean and empty in a dry, shaded location.
BN542.001-0512E/EX
Rev.01
Calle Swissmex No. 500
Col. Las Ceibas,47440
Lagos de Moreno Jalisco,
México
Fax (474) 742-0856, 742-4185
( (474) 741-2200, 741-2201
741-2202
www.swissmex.com
[email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement