YardFeed 200
GB
Origo™
M13y
YardFeed 200
Instruction manual
0459 937 101 GB 20120621
Valid for serial no. 612-xxx-xxxx, 613-xxx-xxxx
-2-
1 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1
4
6
Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
3 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
8
4.1
Lifting instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
5 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
5.1
5.2
5.3
5.4
5.5
Connections and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Function explanations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wire feed pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replacing and inserting wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Changing feed rollers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
9
11
11
12
6 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
6.1
Inspection and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
12
7 ORDERING SPARE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDER NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WEAR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
13
14
16
18
20
Rights reserved to alter specifications without notice.
TOCe
-3-
GB
1
SAFETY
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who works on or
near the equipment observes all the relevant safety precautions. Safety precautions must meet the
requirements that apply to this type of equipment. The following recommendations should be ob­
served in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the equip­
ment. Incorrect operation of the equipment may lead to hazardous situations which can result in in­
jury to the operator and damage to the equipment.
1.
Anyone who uses the equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding and cutting
2.
The operator must ensure that:
S no unauthorised person is stationed within the working area of the equipment when it is
started up.
S no-one is unprotected when the arc is struck
3.
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame-proof
clothing, safety gloves.
S Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which could become
trapped or cause burns.
5.
General precautions
S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.
-4bm47d1ea
© ESAB AB 2005
GB
WARNING
Arc welding and cutting can be injurious to yourself and others. Take precautions when welding and
cutting. Ask for your employer's safety practices which should be based on manufacturers' hazard
data.
ELECTRIC SHOCK - Can kill
S
Install and earth the unit in accordance with applicable standards.
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S
Insulate yourself from earth and the workpiece.
S
Ensure your working stance is safe.
FUMES AND GASES - Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone
and the general area.
ARC RAYS - Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
clothing.
S
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE - Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION - Call for expert assistance in the event of malfunction.
Read and understand the instruction manual before installing or operating.
PROTECT YOURSELF AND OTHERS!
CAUTION
Read and understand the instruction manual before
installing or operating.
CAUTION
This product is solely intended for arc welding.
CAUTION
Class A equipment is not intended for use in residential locations where
the electrical power is provided by the public low-voltage supply system.
There may be potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations, due to conducted
as well as radiated disturbances.
-5bm47d1ea
© ESAB AB 2005
GB
Dispose of electronic equipment at the recycling facility!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical and/or
electronic equipment that has reached the end of its life must be disposed of at a
recycling facility.
As the person responsible for the equipment, it is your responsibility to obtain
information on approved collection stations.
For further information contact the nearest ESAB dealer.
ESAB can provide you with all necessary welding protection and accessories.
2
INTRODUCTION
The wire feed unit YardFeed 200 is intended for MIG/MAG welding together with
stepped and thyristor-controlled welding power sources.
It comes in different variants, see page 16.
The wire feed unit contains a four-wheel drive wire feed mechanism as well as
control electronics.
ESAB's accessories for the product can be found on page 20.
2.1
Equipment
The wire feed unit is supplied with:
S
Instruction manual
S
Decal with recommended wear parts
S
Gas flow meter
-6bm47d1ea
© ESAB AB 2005
GB
3
TECHNICAL DATA
YardFeed 200
Mains voltage
42 V 50-60 Hz
Power requirement
150 VA
Motor current Imax
3.5 A
Settings data
Wire feed speed
Burnback time
2/4 stroke
Gas flushing
Wire inching
1.9 -25.0 m/min
0 -0.5 s
2 stroke or 4 stroke
-
Gun connection
EURO
Max. diameter wire bobbin
200 mm
Wire dimension
Fe
Ss
Al
Cored wire
0.6 - 1.2 mm
0.6 - 1.2 mm
1.0 - 1.2 mm
0.8 - 1.2 mm
Weight
11.3 kg
Dimensions (l x w x h)
593 x 210 x 302 mm
Operating temperature
-10 to +40° C
Shielding gas
max pressure
All types intended for MIG/MAG welding
0.5 MPa ( 5 bar)
Type of cooling
max pressure
50% water / 50% monoetylenglycol
0.5 MPa ( 5 bar)
Maximum permissible load at
60% duty cycle
365 A
Enclosure class
IP23
Duty cycle
The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or cut at
a certain load without overloading. The duty cycle is valid for 40° C.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
-7bm47d1ea
© ESAB AB 2005
GB
4
INSTALLATION
The installation must be carried out by a professional.
WARNING
When welding in an environment with increased electrical danger, only power
sources intended for this environment may be used. These power sources are
marked with the symbol
4.1
Lifting instructions
5
OPERATION
General safety regulations for handling the equipment can be found on
page 4. Read through before you start using the equipment!
WARNING
Assure that the side panels are closed during operation.
WARNING
Rotating parts can cause injury, take great care.
WARNING
Risk of crushing when replacing the wire bobbin!
Do not use safety gloves when inserting the welding wire between the feed rollers.
-8bm47d1ea
© ESAB AB 2005
GB
5.1
Connections and control devices
1
Connection for welding current from power
source, (OKC)
8
Safety contact switch
2
Connection for shielding gas
9
Connection for welding gun
3
Connection for control cable from power
source
10
Toggle switch for gas flushing / wire
inching
4
Connection RED, for coolant to power
source (cooling unit)
11
Toggle switch for 2 stroke/ 4 stroke
5
Connection BLUE, for coolant from power
source (cooling unit)
12
Display
6
Connection RED, for coolant from welding
gun
13
Knob for setting the voltage**
7
Connection BLUE, with ELP* for coolant to
the welding gun
14
Knob for setting wire feed speed
Note! Display (digital instrument) and coolant connections only available on certain models.
* ELP = ESAB Logic Pump, see point 5.2.
** Voltage regulation from the wire feed unit does not function with step regulated power sources.
5.2
Function explanations
Water connection
The wire feed unit with water connection is equipped with a detection system ELP
(ESAB Logic Pump) which checks that the water hoses are connected. When
connecting a water-cooled welding gun, the water pump starts.
Detection only works with power sources that are equipped with ELP.
Strain relief
Hook the strain relief onto the hook on the rear side of the feeder unit and the
connection cable.
-9bm47d1ea
© ESAB AB 2005
GB
Safety contact switch
0 Welding OFF
1 Welding ON
Heat ON (accessory) and welding OFF
The bobbin area is heated so that the welding
wire is not damp when welding .
Gasflow control and burnback time
A = Controlling gas flow.
B = Gas flow meter
C = Setting burnback time.
Burnback time is a delay between the time
when the wire starts to brake until the time
when the power source switches off the
welding voltage. Too short burnback time
results in a long wire stickout after completion
of welding, with a risk of the wire being caught
in the solidifying weld pool. Too long burnback
time results in a shorter stickout, with
increased risk of the arc striking back to the contact tip.
Gas flushing
Gas flushing is used when measuring the gas flow or to flush any air or moisture
from the gas hoses before welding starts. Gas flushing occurs for as long as the
toggle switch is held depressed and occurs without voltage or wire feed starting.
Wire inching
Wire inching is used when one needs to feed wire without welding voltage being
applied. The wire is fed as long as the toggle switch is depressed.
2 stroke
With 2-stroke gasflow starts when the welding gun trigger switch is pressed. The
welding process then starts. Releasing the trigger switch stops welding entirely and
starts burn back time (if selected).
4 stroke
With 4 stroke, the gas flow starts when the welding gun trigger switch is pressed in
and the wire feed starts when it is released. The welding process continues until the
switch is pressed in again, the wire feed and burn back time (if selected) stops when
the switch is released.
- 10 bm47d1ea
© ESAB AB 2005
GB
Voltage
Higher voltage increases the arc length and produces a hotter, wider arc.
NOTE! Voltage regulation from the wire feed unit does not function with step
regulated power sources.
Wire feed speed
This sets the required feed speed of the filler wire in m/minute.
5.3
Wire feed pressure
Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder's pressure rollers. It is important that the
pressure is not too great.
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
ÏÏ
Fig 1
Fig 2
To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.
When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.
If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).
5.4
S
S
S
S
S
S
Replacing and inserting wire
Open the side panel.
Disconnect the pressure sensor by folding it backwards, the pressure rollers
slide up.
Straighten out the new wire 10-20 cm. File away burrs and sharp edges from the
end of the wire before inserting it into the wire feed unit.
Make sure that the wire goes properly into the feed roller's track and into the
outflow nozzle or wire guide.
Secure the pressure sensor.
Close the side panel.
- 11 bm47d1ea
© ESAB AB 2005
GB
5.5
Changing feed rollers
S
S
Open the side panel.
Disconnect the pressure sensor (1) by folding it
backwards, the pressure rollers slide up.
S Disconnect the pressure rollers (2) by turning the
axle (3) 1/4 turn clockwise and pulling out the axle.
The pressure rollers disconnect.
S Disconnect the feed rollers (4) by unscrewing the
nuts (5) and pulling out the rollers.
During installation, repeat the above in reverse order.
Choice of track in the feed rollers
Turn the feed roller with the dimensioning mark for the required
track towards you.
6
MAINTENANCE
Regular maintenance is important for safe, reliable operation.
CAUTION
All guarantee undertakings from the supplier cease to apply if the customer attempts any
work to rectify any faults in the product during the guarantee period.
6.1
Inspection and cleaning
Wire feed unit
Check regularly that the wire feed unit is not clogged with dirt.
S
Cleaning and replacement of the wire feed unit mechanism's worn parts should
take place at regular intervals in order to achieve trouble-free wire feed. Note
that if pre-tensioning is set too hard, this can result in abnormal wear on the
pressure roller, feed roller and wire guide.
The brake hub
The hub is adjusted when delivered.
S
Adjust the brake hub so that wire is slightly slack when wire
feed stops.
- 12 bm47d1ea
© ESAB AB 2005
GB
Welding gun
S
The welding gun's wear parts should be cleaned and replaced at regular
intervals in order to achieve trouble-free wire feed. Blow the wire guide clean
regularly and clean the contact tip.
7
ORDERING SPARE PARTS
YardFeed 200 is designed and tested in accordance with the international and Europe­
an standards EN 60974-5 and EN 60974-10. It is the obligation of the service unit
which has carried out the service or repair work to make sure that the product still
conforms to the said standard.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.
- 13 bm47d1ea
© ESAB AB 2005
Diagram
1366
1
1316
13XP2
13C4
G
13G1
13XS6
F03
13XS5
1313
E01
1312
E02
13XS9
CURRENT RELAY
13XS6
1309
F01
1310
F02
WELDING GUN
13XP1 1366
POWER SOURCE
H
H
F
F
1335
A
A
1333
B
B
1334
+15VB J
J
1367
REF
K
K
1368
0VB
L
L
1369
Arc Voltage
42VAC
3
2
1
13RP2
VOLTAGE
X
R
1320
Y
S
1321
Clock Display
U
U
1361
12V Display
0V
D
E
D
E
1362
1363
Load Display V
V
1364
Data Display
T
1365
T
- 14 bm47e
2
1317
YardFeed 200
© ESAB AB 2005
F04
13C5
2
13S3
2 / 4 STROKE
1
1326
13M1
-
1325
M
Red
Black
+
13XS11
13XS8
J01
B06
J02
13XS2
B07
K01
K02
K04
K03
1354
1355
1357
1356
3
2
GAS PURGE
13S4
1
INCHING
13XS1
13AP01 Control board
A01
1
A02
2
A03
3
1351
1352
1353
3
2
1
13RP1
WIRE FEED
13XS11
B03
3
B04
4
B05
G03 G01
1327
A
3
1
2
C
9
7
8
13S2
13S1
1349
1350
3
2
1
13RP3
BURNBACKTIME
G05
G02 G04
1314
5
1348
13XS7
1315
1328
13YV1
1373 1372
2
1
2
1
13XS4
1383 1382
WATER CONNECTION
MONITORING
13R1
HEATINGKIT
01
02
03
13AP02
Digital instrument
04
05
13XS12
- 15 bm47e
© ESAB AB 2005
YardFeed 200
Order number
Ordering no.
Denomination
Type
0459 906 881 Wire feed unit
Origot YardFeed 200 with control panel M13Y
0459 906 882 Wire feed unit
Origot YardFeed 200 with digital instrument and control
panel M13Y
0459 906 891 Wire feed unit
Origot YardFeed 200 with water cooling and control panel
M13Y
0459 906 892 Wire feed unit
Origot YardFeed 200 with water cooling, digital instrument
and control panel M13Y
0459 839 005 Spare parts list
Origot YardFeed 200
Instruction manuals and the spare parts list are available on the Internet at www.esab.com
- 16 bm47o
© ESAB AB 2005
- 17 p
YardFeed 200
Wear parts
Item
Ordering no.
Denomination
Wire type
HI 1
0455 072 002
0456 615 001
Intermediate nozzle
Intermediate nozzle
Fe, Ss & cored
Al
HI 2
0469 837 880
0469 837 881
Outlet nozzle
Outlet nozzle
Fe, Ss & cored
Al
HI 3
0191 496 114
Key
HI 4
0215 701 007
Locking washer
HI 5a
0459 440 001
Motor gear euro
Item
Ordering no.
Denomination
Wire type
HI 5b
0459 052 001
0459 052 002
0459 052 003
Feed/pressure rollers
Feed/pressure rollers
Feed/pressure rollers
Fe, Ss & cored
Fe, Ss & cored
Fe, Ss & cored
0458 825 001
Feed/pressure rollers
0458 824 001
0458 824 002
0458 824 003
Feed/pressure rollers
Feed/pressure rollers
Feed/pressure rollers
Wire dimensions
Ø 2.0 mm steel for 0.6-1.2 mm
Ø 2.0 mm plastic for 0.8-1.2 mm
Wire dimensions
Groove
typ
Roller
markings
Ø 0.6 & 0.8 mm
Ø 0.8 & 0.9/1.0 mm
Ø 0.9/1.0 & 1.2 mm
V
V
V
0.6 S2 & 0.8 S2
0.8 S2 & 0.9/1.0 S2
0.9/1.0 S2 & 1.2 S2
Cored
Ø 0.9/1.0 & 1.2 mm
V-Knurled
1.0 R2 & 1.2 R2
Al
Al
Al
Ø 0.8 & 0.9/1.0 mm
Ø 1.0 & 1.2 mm
Ø 1.2 mm
U
U
U
0.8 A2 & 1.0 A2
1.0 A2 & 1.2 A2
1.2 A2
Use only pressure and feed rollers marked A2, R2 or S2.
The rollers are marked with wire dimension in mm, some are also marked with inch.
Item
Ordering no.
Denomination
Notes
HI 6
Washer
Ø 16/5x1
HI 7
Screw
M4x12
HI 8
Screw
M6x12
HI 9
Washer
Ø 16/8.4x1.5
HI 10
0469 838 001
Cover
HI 11
0458 722 880
Axle and Nut
HI 12
0459 441 880
Gear adapter
HI 13
0455 049 001
Inlet nozzle
For Fe, Ss, Al and cored wire
0460 007 001
Inlet nozzle
Long-life for Fe, Ss, Al and cored wire
0458 999 001
Shaft
HI 14
Welding with aluminium wire
In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be
used, It is recommended to use 3 m long welding gun for aluminium wire, equipped with appropriate
wear parts.
- 18 bm47vw
© ESAB AB 2005
YardFeed 200
- 19 bm47vw
© ESAB AB 2005
YardFeed 200
Accessories
Digital Volt / Ampere meter . . . . . . . . . . . . . . 0455 173 882
Gas flow meter . . . . . . . . . . . . . . . . . . . . . . . . . 0460 005 880
Heating kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 941 880
Control panel protection . . . . . . . . . . . . . . . . . 0459 961 880
Strain relief for welding gun . . . . . . . . . . . . . 0457 341 881
Water kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0460 006 880
- 20 bm47va
© ESAB AB 2005
YardFeed 200
Connection set air, 19/23 pole
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 582
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 583
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 584
35 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 585
50 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 586
Connection set water, 19/23 pole
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 592
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0459 836 593
0459 836 594
0459 836 595
0459 836 596
Connection set air, 19/19 pole
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 562
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 563
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 564
35 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 565
50 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 566
Connection set water, 19/19 pole
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 836 572
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
35 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
50 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0459 836 573
0459 836 574
0459 836 575
0459 836 576
- 21 bm47va
© ESAB AB 2005
- 22 p
- 23 p
ESAB subsidiaries and representative offices
Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna-Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
BULGARIA
ESAB Kft Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Vamberk
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
ROMANIA
ESAB Romania Trading SRL
Bucharest
Tel: +40 316 900 600
Fax: +40 316 900 601
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
RUSSIA
LLC ESAB
Moscow
Tel: +7 (495) 663 20 08
Fax: +7 (495) 663 20 09
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
UKRAINE
ESAB Ukraine LLC
Kiev
Tel: +38 (044) 501 23 24
Fax: +38 (044) 575 21 88
ITALY
ESAB Saldatura S.p.A.
Bareggio (Mi)
Tel: +39 02 97 96 8.1
Fax: +39 02 97 96 87 01
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem-MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
Africa
EGYPT
ESAB Egypt
Dokki-Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
SOUTH AFRICA
ESAB Africa Welding & Cutting Ltd
Durbanvill 7570 - Cape Town
Tel: +27 (0)21 975 8924
Distributors
For addresses and phone
numbers to our distributors in
other countries, please visit our
home page
www.esab.com
AUSTRALIA
ESAB South Pacific
Archerfield BC QLD 4108
Tel: +61 1300 372 228
Fax: +61 7 3711 2328
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 2326 3000
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 45 670 7073
Fax: +81 45 670 7001
MALAYSIA
ESAB (Malaysia) Snd Bhd
USJ
Tel: +603 8023 7835
Fax: +603 8023 0225
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
THE NETHERLANDS
ESAB Nederland B.V.
Amersfoort
Tel: +31 33 422 35 55
Fax: +31 33 422 35 44
www.esab.com
© ESAB AB
110915
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising