ACD-14-PRO-EUR Dual Display

ACD-14-PRO-EUR Dual Display
www.beha-amprobe.com
ACD-14-PRO-EUR Dual Display
600 A TRMS Clamp Multimeter
Test Voltage and Amperage Simultaneously
The ACD-14-PRO-EUR offers a complete range of measuring
functions for both HVAC and electrical applications.
This modern clamp meter features a large backlit
dual LC-Display and is capable of simultaneously displaying
voltage and amps. The ACD-14-PRO-EUR is packed with
features including TRMS, low pass filter, in-rush current,
frequency, resistance, capacitance, temperature, DC
micro-amps, Amp-Tip and non-contact voltage detection.
The Amp-Tip function allows for precise measurement of
current down to the tenth of an amp for reliable, accurate
current measurement of both large and small diameter
wires. The low pass filter allows measurement of current
and voltage on variable frequency drives (motors with
speed controlled by frequency). The meter features a
rubber over-mold enclosure that provides extra durability
and is safety rated to measurement category CAT III 600 V.
ACD-14-PRO-EUR
Features
Non-Contact
Voltage Detection
(NCV)
Amp-Tip function for
precise Low Current
Measurement
• Large LCD with dual display
that can display voltage and
amps concurrently
• True-RMS for accurate
voltage measurements in noisy
environments
• Low pass filter for current
and voltage measurements on
variable frequency drives
• Amp-Tip function for precise
low current measurement down
to 0.1 Amp
• HVAC applications with
Temperature, DC Micro-amps
and Capacitance
• In-rush current
Rotary Switch for
one-hand operation
Large Dual LC-Display
with Backlight
TRMS Function
provides accurate
measurements
Upper Display:
Reading for AC current
• Temperature
Lower Display:
Reading for V, Hz, Ω, μF,
μA and Temperature
• Non-contact voltage detection
(NCV)
• Audible continuity and
diode test
• Data hold
Rubber
Overmold
for extra
durability
Data Hold Button
Built-in low
pass filter
• Auto ranging
• Auto Power Off
Input
Terminals
• Low Battery indicator
• Safety rated, measurement
category CAT III 600 V
ACD-14-PRO-EUR
Dual Display 600 A TRMS Clamp
Multimeter
Beha-Amprobe® | In den Engematten 14 | 79286 Glottertal, Germany | Tel: +49 (0) 7684 8009-0 | [email protected] | www.beha-amprobe.com
©2015 Beha-Amprobe® 13521-eng
www.beha-amprobe.com
ACD-14-PRO-EUR Key Applications
The Beha-Amprobe ACD-14-PRO-EUR features low
profile jaws to test in tight spaces with TRMS for
accurate measurements.
The ACD-14-PRO-EUR has a full set of functions to cover
a variety of professional applications.
Voltage drop test - dual display allows user to view
voltage and current simultaneously to assess voltage drop for
current changing from zero to a maximum value.
Voltage drop test is required by international standards
(IEC/HD 60364-6) to ensure normal operation and efficiency. It
defines the maximum percentage of the voltage drop between
maximum voltage at zero current and minimum voltage at
maximum current. This assures that electrical equipment and
motors are working within specified voltage to avoid potential
damage to electrical components.
Functions for core HVAC applications: Temperature
measurement (with included thermocouple), capacitance for
start-up and run capacitors, and DC micro-amps for flame sensors
testing.
Accurate measurement of current, voltage and
frequency on all electrical systems including distorted, nonsinusoidal signals (True-RMS function).
Amp-Tip is a small wire guide that is built into the tip of the
main clamp meter jaws. It allows for precise measurement of lowcurrent down to the tenth of an amp on small diameter wires, to
provide reliable, accurate measurements.
The ACD-14-PRO-EUR can test and display voltage and
current measurements simultaneously with the large
backlit LCD dual display, for voltage drop tests and other
applications.
Testing variable frequency drives with low pass filter.
Variable frequency drives are energy efficient motors where
speed is controlled by frequency. These motor drives generate
high frequency noise, which may cause standard meters to
provide erroneous readings when measuring voltage and current.
The low pass filter will remove this noise and provide accurate
measurements.
Capacitance measurement for motor capacitors or
compensation capacitors.
Resistance and continuity functions to verify quality of
electrical connections and to check if motor and transformer coils
are working properly.
In-rush current measurement to verify maximum current
surge during motor start-up. Too high of in-rush current can cause
gradual damage of components and may cause fuses or circuit
breakers to trip.
DC micro-amps range for measurement of flame sensors. Test
the proper operation of the flame sensor safety system in gas
appliances. A broken sensor in a gas appliance will prevent the
safety valve from opening and the appliance will not work.
All Beha-Amprobe tools, including the Beha-Amprobe
ACD-14-PRO-EUR, are rigorously tested for safety, accuracy,
reliability, and ruggedness in our state-of-the-art test lab. In
addition, Beha-Amprobe products that measure electricity are listed
by a 3rd party safety lab. This system assures that Beha-Amprobe
products meet or exceed safety regulations and will perform in a tough,
professional environment for many years to come.
Beha-Amprobe® | In den Engematten 14 | 79286 Glottertal, Germany | Tel: +49 (0) 7684 8009-0 | [email protected] | www.beha-amprobe.com
©2015 Beha-Amprobe® 13521-eng
www.beha-amprobe.com
ACD-14-PRO-EUR Dual Display
Detailed Specifications
Features
ACD-14-PRO-EUR
600 A TRMS Clamp Multimeter
Safety rated, Measurement category
AC Voltage
(with Digital Low-Pass Filter and True-RMS)
DC Voltage
AC Current
(True-RMS)
Precise Low Current AC
(Amp-Tip)
DC micro amps
CAT III 600 V
Range: 0.0 to 600.0 V
Accuracy: ±1.0% + 5LSD (50 to 60 Hz)
Range: 0.0 to 600.0 V
Accuracy: ±1.0% + 5LSD
Range: 0.00 to 600.0 A
Accuracy: ±1.8% + 5LSD (50 to <100 Hz)
±2.0% + 5LSD (100 to 400 Hz)
Range: 0.00 to 60.00 A
Accuracy: ±1.5% + 5LSD (50 to 60 Hz)
Range: 0.0 to 2000 µA
Accuracy: ±1.0% + 5LSD
Frequency
Range: 5.00 to 999.9 Hz
Accuracy: ±1.0% + 5LSD (600 V range)
Resistance
Range: 0.0 Ω to 60.00 kΩ
Accuracy: ±1.0% + 5LSD
Range: > 60.00 kΩ to 6000 kΩ
Accuracy: ±1.2% + 5LSD
Capacitance
Range: 200.0 µF, 2500 µF
Accuracy: ± (2.0 % + 4 LSD)
Diode Test
Range: 0.0 to 3.000 V
Accuracy: ± (1.5 % + 5 LSD)
Continuity Beeper
Temperature*
(Type K thermocouple)
*K-type thermocouple accuracy tolerances
not included
Non-Contact Voltage
Jaw opening
Dual Display
True-RMS
Low Pass Filter
Autoranging
Inrush Current
Data Hold
ON ≤ 10 Ω
OFF > 250 Ω
Range: -40.0 to +752 °F, -40.0 to +400 °C
Accuracy: ±1.0% + 1.5 °F (-40.0 to +99.9 °F)
±1.0% + 2 °F (+100 to +752 °F)
±1.0% + 0.8 °C (-40.0 to +99.9 °C)
±1.0% + 1 °C (+100 to +400 °C)
10 to 550 V, 50/60 Hz
1.18 in (30 mm)
•
•
•
•
•
•
Backlight
•
Auto Power Off
•
Low battery indication
•
General Specifications
Polarity
Dual Display
Update rate
Operating temperature
Automatic
Dual-LCD 33/4 -digit, 6000 counts
5 per second nominal
32 to 104 °F (0 to 40 °C)
Relative humidity
80 %RH up to 88 °F (31 °C) decreasing linearly to 50 %RH at 104 °F (40 °C)
Operating altitude
6,562 ft (0 to 2000 m)
Pollution degree
Storage temperature
Temperature coefficient
Battery
EMC
Safety compliance
2
-4 °F to 140 °F (-20 °C to 60 °C), < 80 % RH
Nominal 0.15 x (specified accuracy)/ °C @ (0 °C to 18 °C or 28 °C to 40 °C)
Two AAA (IEC LR 03) 1.5 V battery
Meets EN 61326-1
UL/IEC/EN 61010-1 ed. 3.0, UL/IEC/EN 61010-2-033 ed. 1.0, CAN/CSA C22.2 NO. 61010-1 ed. 3.0, UL/IEC/EN 61010-2-032 ed. 3.0 & IEC/EN 61010031 ed. 1.1
Certification
Dimensions (L x W x H):
Weight:
8.62 x 3.03 x 1.46 in (219 x 77 x 37 mm)
approx. 0.46 lb (208 g)
Accessories included: User Manual, Test leads, Carrying Case, Batteries AAA (2x), Banana Plug K-type Thermocouple
Beha-Amprobe® | In den Engematten 14 | 79286 Glottertal, Germany | Tel: +49 (0) 7684 8009-0 | [email protected] | www.beha-amprobe.com
©2015 Beha-Amprobe® 13521-eng
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement